arm64: dts: qcom: sm8150: Add SM8150 DTS
v2 cover arm64: dts: qcom: sm8150: Add SM8150 DTS
This series adds DTS for SM8150, PMIC PM8150, PM8150B, PM8150L and the MTP for SM8150.
Changes in v2:
- Squash patches
- Fix comments given by Stephen namely, lowercase for hext numbers, making rpmhcc have xo_board as parent, rename pon controller to power-on controller, make pmic nodes as disabled etc.
- removed the dependency on clk defines and use raw numbers
Vinod Koul (8):
arm64: dts: qcom: sm8150: add base dts file
arm64: dts: qcom: pm8150: Add Base DTS file
arm64: dts: qcom: pm8150b: Add Base DTS file
arm64: dts: qcom: pm8150l: Add Base DTS file
arm64: dts: qcom: sm8150-mtp: add base dts file
arm64: dts: qcom: sm8150-mtp: Add regulators
arm64: dts: qcom: sm8150: Add reserved-memory regions
arm64: dts: qcom: sm8150: Add apps shared nodes
arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/pm8150.dtsi | 95 +++++ arch/arm64/boot/dts/qcom/pm8150b.dtsi | 84 +++++ arch/arm64/boot/dts/qcom/pm8150l.dtsi | 78 ++++ arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 375 +++++++++++++++++++ arch/arm64/boot/dts/qcom/sm8150.dtsi | 479 ++++++++++++++++++++++++ 6 files changed, 1112 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pm8150.dtsi create mode 100644 arch/arm64/boot/dts/qcom/pm8150b.dtsi create mode 100644 arch/arm64/boot/dts/qcom/pm8150l.dtsi create mode 100644 arch/arm64/boot/dts/qcom/sm8150-mtp.dts create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsi
Signature · 1 line
2.20.1
PATCH v2 1/8 arm64: dts: qcom: sm8150: add base dts file
This add base DTS file with cpu, psci, firmware, clock, tlmm and spmi nodes which enables boot to console
--- arch/arm64/boot/dts/qcom/sm8150.dtsi | 305 +++++++++++++++++++++++++++ 1 file changed, 305 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsi
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +305 -0
@@ -0,0 +1,305 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/soc/qcom,rpmh-rsc.h> +#include <dt-bindings/clock/qcom,rpmh.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32764>; + clock-output-names = "sleep_clk"; + }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&L2_100>; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&L2_200>; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&L2_300>; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&L2_400>; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&L2_500>; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x600>; + enable-method = "psci"; + next-level-cache = <&L2_600>; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x700>; + enable-method = "psci"; + next-level-cache = <&L2_700>; + L2_700: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm-sm8150", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0 0x80000000 0 0>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + soc: soc@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8150"; + reg = <0x00100000 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", + "sleep_clk"; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&sleep_clk>; + }; + + qupv3_id_1: geniqup@ac0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x00ac0000 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc 123>, + <&gcc 124>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + uart2: serial@a90000 { + compatible = "qcom,geni-debug-uart"; + reg = <0x00a90000 0x4000>; + clock-names = "se"; + clocks = <&gcc 105>; + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + }; + + tlmm: pinctrl@3100000 { + compatible = "qcom,sm8150-pinctrl"; + reg = <0x03100000 0x300000>, + <0x03500000 0x300000>, + <0x03900000 0x300000>, + <0x03d00000 0x300000>; + reg-names = "west", "east", "north", "south"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&tlmm 0 0 175>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + intc: interrupt-controller@17a00000 { + compatible = "arm,gic-v3"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x17a00000 0x10000>, /* GICD */ + <0x17a60000 0x100000>; /* GICR * 8 */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@17c20000 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x17c20000 0x1000>; + clock-frequency = <19200000>; + + frame@17c21000{ + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c21000 0x1000>, + <0x17c22000 0x1000>; + }; + + frame@17c23000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c23000 0x1000>; + status = "disabled"; + }; + + frame@17c25000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c25000 0x1000>; + status = "disabled"; + }; + + frame@17c27000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c26000 0x1000>; + status = "disabled"; + }; + + frame@17c29000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c29000 0x1000>; + status = "disabled"; + }; + + frame@17c2b000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c2b000 0x1000>; + status = "disabled"; + }; + + frame@17c2d000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c2d000 0x1000>; + status = "disabled"; + }; + }; + + spmi_bus: spmi@c440000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0c440000 0x0001100>, + <0x0c600000 0x2000000>, + <0x0e600000 0x0100000>, + <0x0e700000 0x00a0000>, + <0x0c40a000 0x0026000>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + cell-index = <0>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>; + }; +};
Signature · 1 line
2.20.1
Re: [PATCH v2 1/8] arm64: dts: qcom: sm8150: add base dts file
Quoted 20 lines · Vinod Koul
This add base DTS file with cpu, psci, firmware, clock, tlmm and spmi nodes which enables boot to console
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/sm8150.dtsi | 305 +++++++++++++++++++++++++++ 1 file changed, 305 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsiarch/arm64/boot/dts/qcom/sm8150.dtsi new file +5
-0@@ -0,0 +1,305 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +#include <dt-bindings/interrupt-controller/arm-gic.h>
arch/arm64/boot/dts/qcom/sm8150.dtsi line 15
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +10
-0+#include <dt-bindings/soc/qcom,rpmh-rsc.h> +#include <dt-bindings/clock/qcom,rpmh.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { };
What is the point of an empty node without a label? Perhaps I'm missing something.
Quoted 14 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +14
-0+ + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32764>; + clock-output-names = "sleep_clk";
arch/arm64/boot/dts/qcom/sm8150.dtsi line 39
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +10
-0+ }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo485";
I don't see this compatible inDocumentation/devicetree/bindings/arm/cpus.yaml
Quoted 87 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +87
-0+ reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&L2_100>; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&L2_200>; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&L2_300>; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&L2_400>; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&L2_500>; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x600>; + enable-method = "psci"; + next-level-cache = <&L2_600>; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu";
arch/arm64/boot/dts/qcom/sm8150.dtsi line 136
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +10
-0+ compatible = "qcom,kryo485"; + reg = <0x0 0x700>; + enable-method = "psci"; + next-level-cache = <&L2_700>; + L2_700: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + };
I was expecting to see the cpu-map here, defining
the core to cluster relationship.
Quoted 33 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +33
-0+ + firmware { + scm: scm { + compatible = "qcom,scm-sm8150", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0 0x80000000 0 0>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + soc: soc@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8150"; + reg = <0x00100000 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", + "sleep_clk";
arch/arm64/boot/dts/qcom/sm8150.dtsi line 179
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +10
-0+ clocks = <&rpmhcc RPMH_CXO_CLK>, + <&sleep_clk>; + }; + + qupv3_id_1: geniqup@ac0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x00ac0000 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc 123>, + <&gcc 124>;
Is there no defines for these?
Quoted 129 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +126
-0+ #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + uart2: serial@a90000 { + compatible = "qcom,geni-debug-uart"; + reg = <0x00a90000 0x4000>; + clock-names = "se"; + clocks = <&gcc 105>; + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + }; + + tlmm: pinctrl@3100000 { + compatible = "qcom,sm8150-pinctrl"; + reg = <0x03100000 0x300000>, + <0x03500000 0x300000>, + <0x03900000 0x300000>, + <0x03d00000 0x300000>; + reg-names = "west", "east", "north", "south"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&tlmm 0 0 175>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + intc: interrupt-controller@17a00000 { + compatible = "arm,gic-v3"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x17a00000 0x10000>, /* GICD */ + <0x17a60000 0x100000>; /* GICR * 8 */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@17c20000 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x17c20000 0x1000>; + clock-frequency = <19200000>; + + frame@17c21000{ + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c21000 0x1000>, + <0x17c22000 0x1000>; + }; + + frame@17c23000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c23000 0x1000>; + status = "disabled"; + }; + + frame@17c25000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c25000 0x1000>; + status = "disabled"; + }; + + frame@17c27000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c26000 0x1000>; + status = "disabled"; + }; + + frame@17c29000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c29000 0x1000>; + status = "disabled"; + }; + + frame@17c2b000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c2b000 0x1000>; + status = "disabled"; + }; + + frame@17c2d000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c2d000 0x1000>; + status = "disabled"; + }; + }; + + spmi_bus: spmi@c440000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0c440000 0x0001100>, + <0x0c600000 0x2000000>, + <0x0e600000 0x0100000>, + <0x0e700000 0x00a0000>, + <0x0c40a000 0x0026000>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + cell-index = <0>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>; + }; +};Signature · 1 line
2.20.1
Re: [PATCH v2 1/8] arm64: dts: qcom: sm8150: add base dts file
Quoted 26 lines · Niklas Cassel
Quoted 25 lines · Vinod Koul
This add base DTS file with cpu, psci, firmware, clock, tlmm and spmi nodes which enables boot to console
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/sm8150.dtsi | 305 +++++++++++++++++++++++++++ 1 file changed, 305 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsiarch/arm64/boot/dts/qcom/sm8150.dtsi new file +10
-0@@ -0,0 +1,305 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/soc/qcom,rpmh-rsc.h> +#include <dt-bindings/clock/qcom,rpmh.h> + +/ { + interrupt-parent = <&intc>;
Quoted 8 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi line 15
Quoted 5 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +5
-0+ + #address-cells = <2>; + #size-cells = <2>; + + chosen { };What is the point of an empty node without a label? Perhaps I'm missing something.
Hmm that seems to be the case with other dts in qcom folder :), we do have chosen in mtp dts as well which is not empty
Quoted 20 lines
Quoted 20 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +19
-0+ + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32764>; + clock-output-names = "sleep_clk"; + }; + }; + + cpus { + #address-cells = <2>;
Quoted 8 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi line 39
Quoted 5 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +5
-0+ #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo485";I don't see this compatible in
Documentation/devicetree/bindings/arm/cpus.yaml
Thanks for pointing, will send
Quoted 93 lines
Quoted 93 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +92
-0+ reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&L2_100>; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&L2_200>; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&L2_300>; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&L2_400>; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&L2_500>; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x600>; + enable-method = "psci"; + next-level-cache = <&L2_600>; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x700>; + enable-method = "psci"; + next-level-cache = <&L2_700>; + L2_700: l2-cache {
Quoted 8 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi line 50
Quoted 5 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +5
-0+ compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + };I was expecting to see the cpu-map here, defining
the core to cluster relationship.
That would come later with bunch of other support
Quoted 38 lines
Quoted 38 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +37
-0+ + firmware { + scm: scm { + compatible = "qcom,scm-sm8150", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0 0x80000000 0 0>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + soc: soc@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8150"; + reg = <0x00100000 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", + "sleep_clk"; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&sleep_clk>; + }; +
Quoted 8 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi line 179
Quoted 6 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +6
-0+ qupv3_id_1: geniqup@ac0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x00ac0000 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc 123>, + <&gcc 124>;Is there no defines for these?
It is, but if you look at cover we did that here so that we can get these merged and not worry about dependency. The defines are in clock tree. After next cycle these will be replaced with defines.
Signature · 1 line
~Vinod
Re: [PATCH v2 1/8] arm64: dts: qcom: sm8150: add base dts file
In reply to Vinod KoulQuoted 16 lines · Vinod Koul
This add base DTS file with cpu, psci, firmware, clock, tlmm and spmi nodes which enables boot to console
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/sm8150.dtsi | 305 +++++++++++++++++++++++++++ 1 file changed, 305 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsiarch/arm64/boot/dts/qcom/sm8150.dtsi new file +0
-0
arch/arm64/boot/dts/qcom/sm8150.dtsi line 1
Quoted 1 line
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +1
-0@@ -0,0 +1,305 @@ +// SPDX-License-Identifier: BSD-3-Clause
This is fine.
arch/arm64/boot/dts/qcom/sm8150.dtsi line 3
Quoted 2 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +2
-0+// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited
These two lines should be in /* */
Quoted 289 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +289
-0+ +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/soc/qcom,rpmh-rsc.h> +#include <dt-bindings/clock/qcom,rpmh.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32764>; + clock-output-names = "sleep_clk"; + }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&L2_100>; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&L2_200>; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&L2_300>; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&L2_400>; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&L2_500>; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x600>; + enable-method = "psci"; + next-level-cache = <&L2_600>; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x700>; + enable-method = "psci"; + next-level-cache = <&L2_700>; + L2_700: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + }; + firmware { + scm: scm { + compatible = "qcom,scm-sm8150", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0 0x80000000 0 0>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + soc: soc@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8150"; + reg = <0x00100000 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", + "sleep_clk"; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&sleep_clk>; + }; + + qupv3_id_1: geniqup@ac0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x00ac0000 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc 123>, + <&gcc 124>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + uart2: serial@a90000 { + compatible = "qcom,geni-debug-uart"; + reg = <0x00a90000 0x4000>; + clock-names = "se"; + clocks = <&gcc 105>; + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + }; + + tlmm: pinctrl@3100000 { + compatible = "qcom,sm8150-pinctrl"; + reg = <0x03100000 0x300000>, + <0x03500000 0x300000>, + <0x03900000 0x300000>, + <0x03d00000 0x300000>; + reg-names = "west", "east", "north", "south"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&tlmm 0 0 175>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + intc: interrupt-controller@17a00000 { + compatible = "arm,gic-v3"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x17a00000 0x10000>, /* GICD */ + <0x17a60000 0x100000>; /* GICR * 8 */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@17c20000 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x17c20000 0x1000>; + clock-frequency = <19200000>; + + frame@17c21000{ + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c21000 0x1000>, + <0x17c22000 0x1000>; + }; + + frame@17c23000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c23000 0x1000>; + status = "disabled"; + }; + + frame@17c25000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c25000 0x1000>; + status = "disabled"; + }; + + frame@17c27000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c26000 0x1000>; + status = "disabled"; + }; + + frame@17c29000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c29000 0x1000>; + status = "disabled"; + }; + + frame@17c2b000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c2b000 0x1000>; + status = "disabled"; + }; + + frame@17c2d000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x17c2d000 0x1000>; + status = "disabled"; + }; + }; + + spmi_bus: spmi@c440000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0c440000 0x0001100>, + <0x0c600000 0x2000000>, + <0x0e600000 0x0100000>, + <0x0e700000 0x00a0000>, + <0x0c40a000 0x0026000>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>;
arch/arm64/boot/dts/qcom/sm8150.dtsi line 303
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +10
-0+ cell-index = <0>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;
Any particular reason why these are defined in this order - 1, 2, 3, 0?
Quoted 5 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +2
-1+ }; +}; --2.20.1
Re: [PATCH v2 1/8] arm64: dts: qcom: sm8150: add base dts file
Quoted 21 lines · Amit Kucheria
Quoted 16 lines · Vinod Koul
This add base DTS file with cpu, psci, firmware, clock, tlmm and spmi nodes which enables boot to console
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/sm8150.dtsi | 305 +++++++++++++++++++++++++++ 1 file changed, 305 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsiarch/arm64/boot/dts/qcom/sm8150.dtsi new file +0
-0arch/arm64/boot/dts/qcom/sm8150.dtsi line 1
Quoted 1 line
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +1
-0@@ -0,0 +1,305 @@ +// SPDX-License-Identifier: BSD-3-ClauseThis is fine.
Quoted 4 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi line 3
Quoted 2 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +2
-0+// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro LimitedThese two lines should be in /* */
Yeah I made it same as previous, lets do right style.
Quoted 8 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi line 303
Quoted 6 lines
arch/arm64/boot/dts/qcom/sm8150.dtsi new file +6
-0+ timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;Any particular reason why these are defined in this order - 1, 2, 3, 0?
Copied from downstream :)
Signature · 1 line
~Vinod
PATCH v2 2/8 arm64: dts: qcom: pm8150: Add Base DTS file
In reply to Vinod KoulAdd base DTS file for pm8150 along with GPIOs, power-on, rtc and vadc nodes
--- arch/arm64/boot/dts/qcom/pm8150.dtsi | 95 ++++++++++++++++++++++++++++ 1 file changed, 95 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pm8150.dtsi
arch/arm64/boot/dts/qcom/pm8150.dtsi new file +95 -0
@@ -0,0 +1,95 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> +#include <dt-bindings/iio/qcom,spmi-vadc.h> + +&spmi_bus { + pm8150_0: pmic@0 { + compatible = "qcom,pm8150", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pon: power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_POWER>; + + status = "disabled"; + }; + }; + + pm8150_adc: adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + status = "disabled"; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + }; + + rtc@6000 { + compatible = "qcom,pm8941-rtc"; + reg = <0x6000>; + reg-names = "rtc", "alarm"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; + + status = "disabled"; + }; + + pm8150_gpios: gpio@c000 { + compatible = "qcom,pm8150-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <0 0xc0 0 IRQ_TYPE_NONE>, + <0 0xc1 0 IRQ_TYPE_NONE>, + <0 0xc2 0 IRQ_TYPE_NONE>, + <0 0xc3 0 IRQ_TYPE_NONE>, + <0 0xc4 0 IRQ_TYPE_NONE>, + <0 0xc5 0 IRQ_TYPE_NONE>, + <0 0xc6 0 IRQ_TYPE_NONE>, + <0 0xc7 0 IRQ_TYPE_NONE>, + <0 0xc8 0 IRQ_TYPE_NONE>, + <0 0xc9 0 IRQ_TYPE_NONE>, + <0 0xca 0 IRQ_TYPE_NONE>, + <0 0xcb 0 IRQ_TYPE_NONE>; + }; + }; + + pmic@1 { + compatible = "qcom,pm8150", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +};
Signature · 1 line
2.20.1
Re: [PATCH v2 2/8] arm64: dts: qcom: pm8150: Add Base DTS file
Quoted 27 lines · Vinod Koul
Add base DTS file for pm8150 along with GPIOs, power-on, rtc and vadc nodes
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/pm8150.dtsi | 95 ++++++++++++++++++++++++++++ 1 file changed, 95 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pm8150.dtsiarch/arm64/boot/dts/qcom/pm8150.dtsi new file +12
-0@@ -0,0 +1,95 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> +#include <dt-bindings/iio/qcom,spmi-vadc.h> + +&spmi_bus { + pm8150_0: pmic@0 { + compatible = "qcom,pm8150", "qcom,spmi-pmic";
arch/arm64/boot/dts/qcom/pm8150.dtsi line 22
Quoted 10 lines
arch/arm64/boot/dts/qcom/pm8150.dtsi new file +10
-0+ reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pon: power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
Here you use 0 for 3rd cell
Quoted 5 lines
arch/arm64/boot/dts/qcom/pm8150.dtsi new file +5
-0+ debounce = <15625>; + bias-pull-up; + linux,code = <KEY_POWER>; + + status = "disabled";
arch/arm64/boot/dts/qcom/pm8150.dtsi line 37
Quoted 10 lines
arch/arm64/boot/dts/qcom/pm8150.dtsi new file +10
-0+ }; + }; + + pm8150_adc: adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
Here you use 0x0 for 3rd cell, be consistent.
Quoted 61 lines
arch/arm64/boot/dts/qcom/pm8150.dtsi new file +58
-0+ + status = "disabled"; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + }; + + rtc@6000 { + compatible = "qcom,pm8941-rtc"; + reg = <0x6000>; + reg-names = "rtc", "alarm"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; + + status = "disabled"; + }; + + pm8150_gpios: gpio@c000 { + compatible = "qcom,pm8150-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <0 0xc0 0 IRQ_TYPE_NONE>, + <0 0xc1 0 IRQ_TYPE_NONE>, + <0 0xc2 0 IRQ_TYPE_NONE>, + <0 0xc3 0 IRQ_TYPE_NONE>, + <0 0xc4 0 IRQ_TYPE_NONE>, + <0 0xc5 0 IRQ_TYPE_NONE>, + <0 0xc6 0 IRQ_TYPE_NONE>, + <0 0xc7 0 IRQ_TYPE_NONE>, + <0 0xc8 0 IRQ_TYPE_NONE>, + <0 0xc9 0 IRQ_TYPE_NONE>, + <0 0xca 0 IRQ_TYPE_NONE>, + <0 0xcb 0 IRQ_TYPE_NONE>; + }; + }; + + pmic@1 { + compatible = "qcom,pm8150", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +};Signature · 1 line
2.20.1
Re: [PATCH v2 2/8] arm64: dts: qcom: pm8150: Add Base DTS file
Quoted 50 lines · Niklas Cassel
Quoted 27 lines · Vinod Koul
Add base DTS file for pm8150 along with GPIOs, power-on, rtc and vadc nodes
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/pm8150.dtsi | 95 ++++++++++++++++++++++++++++ 1 file changed, 95 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pm8150.dtsiarch/arm64/boot/dts/qcom/pm8150.dtsi new file +12
-0@@ -0,0 +1,95 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> +#include <dt-bindings/iio/qcom,spmi-vadc.h> + +&spmi_bus { + pm8150_0: pmic@0 { + compatible = "qcom,pm8150", "qcom,spmi-pmic";arch/arm64/boot/dts/qcom/pm8150.dtsi line 22
Quoted 10 lines
arch/arm64/boot/dts/qcom/pm8150.dtsi new file +10
-0+ reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pon: power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;Here you use 0 for 3rd cell
Quoted 9 lines
arch/arm64/boot/dts/qcom/pm8150.dtsi new file +9
-0+ debounce = <15625>; + bias-pull-up; + linux,code = <KEY_POWER>; + + status = "disabled"; + }; + }; + + pm8150_adc: adc@3100 {
Quoted 8 lines
arch/arm64/boot/dts/qcom/pm8150.dtsi line 37
Quoted 6 lines
arch/arm64/boot/dts/qcom/pm8150.dtsi new file +6
-0+ compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;Here you use
0x0for 3rd cell, be consistent.
Will make it either at this and other places, thanks for pointing!
Signature · 1 line
~Vinod
PATCH v2 3/8 arm64: dts: qcom: pm8150b: Add Base DTS file
In reply to Vinod KoulPMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b with pon, adc, and gpio nodes
--- arch/arm64/boot/dts/qcom/pm8150b.dtsi | 84 +++++++++++++++++++++++++++ 1 file changed, 84 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pm8150b.dtsi
arch/arm64/boot/dts/qcom/pm8150b.dtsi new file +84 -0
@@ -0,0 +1,84 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +#include <dt-bindings/iio/qcom,spmi-vadc.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pmic@2 { + compatible = "qcom,pm8150b", "qcom,spmi-pmic"; + reg = <0x2 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + + status = "disabled"; + }; + + adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + status = "disabled"; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + + chg-temp@9 { + reg = <ADC5_CHG_TEMP>; + qcom,pre-scaling = <1 1>; + label = "chg_temp"; + }; + }; + + pm8150b_gpios: gpio@c000 { + compatible = "qcom,pm8150b-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <0x2 0xc0 0 IRQ_TYPE_NONE>, + <0x2 0xc1 0 IRQ_TYPE_NONE>, + <0x2 0xc2 0 IRQ_TYPE_NONE>, + <0x2 0xc3 0 IRQ_TYPE_NONE>, + <0x2 0xc4 0 IRQ_TYPE_NONE>, + <0x2 0xc5 0 IRQ_TYPE_NONE>, + <0x2 0xc6 0 IRQ_TYPE_NONE>, + <0x2 0xc7 0 IRQ_TYPE_NONE>, + <0x2 0xc8 0 IRQ_TYPE_NONE>, + <0x2 0xc9 0 IRQ_TYPE_NONE>, + <0x2 0xca 0 IRQ_TYPE_NONE>, + <0x2 0xcb 0 IRQ_TYPE_NONE>; + }; + }; + + pmic@3 { + compatible = "qcom,pm8150b", "qcom,spmi-pmic"; + reg = <0x3 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +};
Signature · 1 line
2.20.1
Re: [PATCH v2 3/8] arm64: dts: qcom: pm8150b: Add Base DTS file
Quoted 2 lines · Vinod Koul
PMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b with pon, adc, and gpio nodes
All of your other commit messages refers to it as power-on instead of pon, be consistent.
Quoted 100 lines
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/pm8150b.dtsi | 84 +++++++++++++++++++++++++++ 1 file changed, 84 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pm8150b.dtsiarch/arm64/boot/dts/qcom/pm8150b.dtsi new file +84
-0@@ -0,0 +1,84 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +#include <dt-bindings/iio/qcom,spmi-vadc.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pmic@2 { + compatible = "qcom,pm8150b", "qcom,spmi-pmic"; + reg = <0x2 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + + status = "disabled"; + }; + + adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + status = "disabled"; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + + chg-temp@9 { + reg = <ADC5_CHG_TEMP>; + qcom,pre-scaling = <1 1>; + label = "chg_temp"; + }; + }; + + pm8150b_gpios: gpio@c000 { + compatible = "qcom,pm8150b-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <0x2 0xc0 0 IRQ_TYPE_NONE>, + <0x2 0xc1 0 IRQ_TYPE_NONE>, + <0x2 0xc2 0 IRQ_TYPE_NONE>, + <0x2 0xc3 0 IRQ_TYPE_NONE>, + <0x2 0xc4 0 IRQ_TYPE_NONE>, + <0x2 0xc5 0 IRQ_TYPE_NONE>, + <0x2 0xc6 0 IRQ_TYPE_NONE>, + <0x2 0xc7 0 IRQ_TYPE_NONE>, + <0x2 0xc8 0 IRQ_TYPE_NONE>, + <0x2 0xc9 0 IRQ_TYPE_NONE>, + <0x2 0xca 0 IRQ_TYPE_NONE>, + <0x2 0xcb 0 IRQ_TYPE_NONE>; + }; + }; + + pmic@3 { + compatible = "qcom,pm8150b", "qcom,spmi-pmic"; + reg = <0x3 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +};Signature · 1 line
2.20.1
Re: [PATCH v2 3/8] arm64: dts: qcom: pm8150b: Add Base DTS file
Quoted 6 lines · Niklas Cassel
Quoted 2 lines · Vinod Koul
PMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b with pon, adc, and gpio nodes
All of your other commit messages refers to it as power-on instead of pon, be consistent.
I missed this one, will updated :)
Signature · 1 line
~Vinod
PATCH v2 4/8 arm64: dts: qcom: pm8150l: Add Base DTS file
In reply to Vinod KoulPMIC pm8150l is a slave pmic and this adds base DTS file for pm8150l with power-on, adc and gpio nodes
--- arch/arm64/boot/dts/qcom/pm8150l.dtsi | 78 +++++++++++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pm8150l.dtsi
arch/arm64/boot/dts/qcom/pm8150l.dtsi new file +78 -0
@@ -0,0 +1,78 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +#include <dt-bindings/iio/qcom,spmi-vadc.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pmic@4 { + compatible = "qcom,pm8150l", "qcom,spmi-pmic"; + reg = <0x4 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + + status = "disabled"; + }; + + adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + status = "disabled"; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + }; + + pm8150l_gpios: gpio@c000 { + compatible = "qcom,pm8150l-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <0x4 0xc0 0 IRQ_TYPE_NONE>, + <0x4 0xc1 0 IRQ_TYPE_NONE>, + <0x4 0xc2 0 IRQ_TYPE_NONE>, + <0x4 0xc3 0 IRQ_TYPE_NONE>, + <0x4 0xc4 0 IRQ_TYPE_NONE>, + <0x4 0xc5 0 IRQ_TYPE_NONE>, + <0x4 0xc6 0 IRQ_TYPE_NONE>, + <0x4 0xc7 0 IRQ_TYPE_NONE>, + <0x4 0xc8 0 IRQ_TYPE_NONE>, + <0x4 0xc9 0 IRQ_TYPE_NONE>, + <0x4 0xca 0 IRQ_TYPE_NONE>, + <0x4 0xcb 0 IRQ_TYPE_NONE>; + }; + }; + + pmic@5 { + compatible = "qcom,pm8150l", "qcom,spmi-pmic"; + reg = <0x5 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +};
Signature · 1 line
2.20.1
PATCH v2 5/8 arm64: dts: qcom: sm8150-mtp: add base dts file
In reply to Vinod KoulThis add base DTS file for sm8150-mtp and enables boot to console, adds tlmm reserved range, resin node, volume down key and also includes pmic file.
--- arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 48 +++++++++++++++++++++++++ 2 files changed, 49 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8150-mtp.dts
arch/arm64/boot/dts/qcom/Makefile +1 -0
@@ -12,5 +12,6 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
arch/arm64/boot/dts/qcom/sm8150-mtp.dts new file +48 -0
48 lines not on this page · raw message
Signature · 1 line
2.20.1
Re: [PATCH v2 5/8] arm64: dts: qcom: sm8150-mtp: add base dts file
Quoted 59 lines · Vinod Koul
This add base DTS file for sm8150-mtp and enables boot to console, adds tlmm reserved range, resin node, volume down key and also includes pmic file.
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 48 +++++++++++++++++++++++++ 2 files changed, 49 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8150-mtp.dtsarch/arm64/boot/dts/qcom/Makefile +1
-0@@ -12,5 +12,6 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtbarch/arm64/boot/dts/qcom/sm8150-mtp.dts new file +31
-0@@ -0,0 +1,48 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +/dts-v1/; + +#include "sm8150.dtsi" +#include "pm8150.dtsi" +#include "pm8150b.dtsi" +#include "pm8150l.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. SM8150 MTP"; + compatible = "qcom,sm8150-mtp"; + + aliases { + serial0 = &uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&pon { + pwrkey { + status = "okay";
arch/arm64/boot/dts/qcom/sm8150-mtp.dts line 41
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8150-mtp.dts new file +10
-0+ }; + + resin { + compatible = "qcom,pm8941-resin"; + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_VOLUMEDOWN>; + }; +};
Missing a newline here.
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8150-mtp.dts new file +7
-0+&tlmm { + gpio-reserved-ranges = <0 4>, <126 4>; +}; + +&uart2 { + status = "okay"; +};Signature · 1 line
2.20.1
Re: [PATCH v2 5/8] arm64: dts: qcom: sm8150-mtp: add base dts file
Quoted 64 lines · Niklas Cassel
Quoted 63 lines · Vinod Koul
This add base DTS file for sm8150-mtp and enables boot to console, adds tlmm reserved range, resin node, volume down key and also includes pmic file.
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 48 +++++++++++++++++++++++++ 2 files changed, 49 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8150-mtp.dtsarch/arm64/boot/dts/qcom/Makefile +1
-0@@ -12,5 +12,6 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtbarch/arm64/boot/dts/qcom/sm8150-mtp.dts new file +35
-0@@ -0,0 +1,48 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Linaro Limited + +/dts-v1/; + +#include "sm8150.dtsi" +#include "pm8150.dtsi" +#include "pm8150b.dtsi" +#include "pm8150l.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. SM8150 MTP"; + compatible = "qcom,sm8150-mtp"; + + aliases { + serial0 = &uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&pon { + pwrkey { + status = "okay"; + }; + + resin { + compatible = "qcom,pm8941-resin";
Quoted 8 lines
arch/arm64/boot/dts/qcom/sm8150-mtp.dts line 41
Quoted 6 lines
arch/arm64/boot/dts/qcom/sm8150-mtp.dts new file +6
-0+ interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_VOLUMEDOWN>; + }; +};Missing a newline here.
Yup will updated
Signature · 1 line
~Vinod
PATCH v2 6/8 arm64: dts: qcom: sm8150-mtp: Add regulators
In reply to Vinod KoulAdd the regulators found in the mtp platform. This platform consists of pmic PM8150, PM8150L and PM8009.
--- arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 327 ++++++++++++++++++++++++ 1 file changed, 327 insertions(+)
arch/arm64/boot/dts/qcom/sm8150-mtp.dts +327 -0
@@ -4,6 +4,7 @@ /dts-v1/; +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sm8150.dtsi" #include "pm8150.dtsi" #include "pm8150b.dtsi"
@@ -20,6 +21,332 @@ chosen { stdout-path = "serial0:115200n8"; }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + /* + * Apparently RPMh does not provide support for PM8150 S4 because it + * is always-on; model it as a fixed regulator. + */ + vreg_s4a_1p8: pm8150-s4 { + compatible = "regulator-fixed"; + regulator-name = "vreg_s4a_1p8"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; +}; + +&apps_rsc { + pm8150-rpmh-regulators { + compatible = "qcom,pm8150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + + vdd-l1-l8-l11-supply = <&vreg_s6a_0p9>; + vdd-l2-l10-supply = <&vreg_bob>; + vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p9>; + vdd-l6-l9-supply = <&vreg_s8c_1p3>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>; + vdd-l13-l16-l17-supply = <&vreg_bob>; + + vreg_s5a_2p0: smps5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_s6a_0p9: smps6 { + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <1128000>; + }; + + vdda_wcss_pll: + vreg_l1a_0p75: ldo1 { + regulator-min-microvolt = <752000>; + regulator-max-microvolt = <752000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_pdphy: + vdda_usb_hs_3p1: + vreg_l2a_3p1: ldo2 { + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3a_0p8: ldo3 { + regulator-min-microvolt = <480000>; + regulator-max-microvolt = <932000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_usb_hs_core: + vdda_csi_0_0p9: + vdda_csi_1_0p9: + vdda_csi_2_0p9: + vdda_csi_3_0p9: + vdda_dsi_0_0p9: + vdda_dsi_1_0p9: + vdda_dsi_0_pll_0p9: + vdda_dsi_1_pll_0p9: + vdda_pcie_1ln_core: + vdda_pcie_2ln_core: + vdda_pll_hv_cc_ebi01: + vdda_pll_hv_cc_ebi23: + vdda_qrefs_0p875_5: + vdda_sp_sensor: + vdda_ufs_2ln_core_1: + vdda_ufs_2ln_core_2: + vdda_usb_ss_dp_core_1: + vdda_usb_ss_dp_core_2: + vdda_qlink_lv: + vdda_qlink_lv_ck: + vreg_l5a_0p875: ldo5 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6a_1p2: ldo6 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a_1p8: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_10: + vreg_l9a_1p2: ldo9 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + + vreg_l10a_2p5: ldo10 { + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11a_0p8: ldo11 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_qfprom: + vdd_qfprom_sp: + vdda_apc_cs_1p8: + vdda_gfx_cs_1p8: + vdda_usb_hs_1p8: + vdda_qrefs_vref_1p8: + vddpx_10_a: + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13a_2p7: ldo13 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14a_1p8: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15a_1p7: ldo15 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <1704000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16a_2p7: ldo16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a_3p0: ldo17 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pm8150l-rpmh-regulators { + compatible = "qcom,pm8150l-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + + vdd-l1-l8-supply = <&vreg_s4a_1p8>; + vdd-l2-l3-supply = <&vreg_s8c_1p3>; + vdd-l4-l5-l6-supply = <&vreg_bob>; + vdd-l7-l11-supply = <&vreg_bob>; + vdd-l9-l10-supply = <&vreg_bob>; + + vdd-bob-supply = <&vph_pwr>; + vdd-flash-supply = <&vreg_bob>; + vdd-rgb-supply = <&vreg_bob>; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <4000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + regulator-allow-bypass; + }; + + vreg_s8c_1p3: smps8 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_wcss_adcdac_1: + vdda_wcss_adcdac_22: + vreg_l2c_1p3: ldo2 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_hv_ebi0: + vdda_hv_ebi1: + vdda_hv_ebi2: + vdda_hv_ebi3: + vdda_hv_refgen0: + vdda_qlink_hv_ck: + vreg_l3c_1p2: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_5: + vreg_l4c_1p8: ldo4 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_6: + vreg_l5c_1p8: ldo5 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_2: + vreg_l6c_2p9: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c_3p0: ldo7 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c_2p9: ldo9 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + + vreg_l10c_3p3: ldo10 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11c_3p3: ldo11 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pm8009-rpmh-regulators { + compatible = "qcom,pm8009-rpmh-regulators"; + qcom,pmic-id = "f"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vreg_bob>; + + vdd-l2-supply = <&vreg_s8c_1p3>; + vdd-l5-l6-supply = <&vreg_bob>; + + vreg_l2f_1p2: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5f_2p85: ldo5 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6f_2p85: ldo6 { + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <2856000>; + }; + }; + }; &qupv3_id_1 {
Signature · 1 line
2.20.1
Re: [PATCH v2 6/8] arm64: dts: qcom: sm8150-mtp: Add regulators
Quoted 2 lines · Vinod Koul
Add the regulators found in the mtp platform. This platform consists of pmic PM8150, PM8150L and PM8009.
Is there a reason not to squash this this patch 5/8 ?
Quoted 354 lines
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 327 ++++++++++++++++++++++++ 1 file changed, 327 insertions(+)arch/arm64/boot/dts/qcom/sm8150-mtp.dts +327
-0@@ -4,6 +4,7 @@ /dts-v1/; +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sm8150.dtsi" #include "pm8150.dtsi" #include "pm8150b.dtsi"@@ -20,6 +21,332 @@ chosen { stdout-path = "serial0:115200n8"; }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + /* + * Apparently RPMh does not provide support for PM8150 S4 because it + * is always-on; model it as a fixed regulator. + */ + vreg_s4a_1p8: pm8150-s4 { + compatible = "regulator-fixed"; + regulator-name = "vreg_s4a_1p8"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; +}; + +&apps_rsc { + pm8150-rpmh-regulators { + compatible = "qcom,pm8150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + + vdd-l1-l8-l11-supply = <&vreg_s6a_0p9>; + vdd-l2-l10-supply = <&vreg_bob>; + vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p9>; + vdd-l6-l9-supply = <&vreg_s8c_1p3>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>; + vdd-l13-l16-l17-supply = <&vreg_bob>; + + vreg_s5a_2p0: smps5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_s6a_0p9: smps6 { + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <1128000>; + }; + + vdda_wcss_pll: + vreg_l1a_0p75: ldo1 { + regulator-min-microvolt = <752000>; + regulator-max-microvolt = <752000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_pdphy: + vdda_usb_hs_3p1: + vreg_l2a_3p1: ldo2 { + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3a_0p8: ldo3 { + regulator-min-microvolt = <480000>; + regulator-max-microvolt = <932000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_usb_hs_core: + vdda_csi_0_0p9: + vdda_csi_1_0p9: + vdda_csi_2_0p9: + vdda_csi_3_0p9: + vdda_dsi_0_0p9: + vdda_dsi_1_0p9: + vdda_dsi_0_pll_0p9: + vdda_dsi_1_pll_0p9: + vdda_pcie_1ln_core: + vdda_pcie_2ln_core: + vdda_pll_hv_cc_ebi01: + vdda_pll_hv_cc_ebi23: + vdda_qrefs_0p875_5: + vdda_sp_sensor: + vdda_ufs_2ln_core_1: + vdda_ufs_2ln_core_2: + vdda_usb_ss_dp_core_1: + vdda_usb_ss_dp_core_2: + vdda_qlink_lv: + vdda_qlink_lv_ck: + vreg_l5a_0p875: ldo5 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6a_1p2: ldo6 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a_1p8: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_10: + vreg_l9a_1p2: ldo9 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + + vreg_l10a_2p5: ldo10 { + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11a_0p8: ldo11 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_qfprom: + vdd_qfprom_sp: + vdda_apc_cs_1p8: + vdda_gfx_cs_1p8: + vdda_usb_hs_1p8: + vdda_qrefs_vref_1p8: + vddpx_10_a: + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13a_2p7: ldo13 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14a_1p8: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15a_1p7: ldo15 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <1704000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16a_2p7: ldo16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a_3p0: ldo17 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pm8150l-rpmh-regulators { + compatible = "qcom,pm8150l-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + + vdd-l1-l8-supply = <&vreg_s4a_1p8>; + vdd-l2-l3-supply = <&vreg_s8c_1p3>; + vdd-l4-l5-l6-supply = <&vreg_bob>; + vdd-l7-l11-supply = <&vreg_bob>; + vdd-l9-l10-supply = <&vreg_bob>; + + vdd-bob-supply = <&vph_pwr>; + vdd-flash-supply = <&vreg_bob>; + vdd-rgb-supply = <&vreg_bob>; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <4000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + regulator-allow-bypass; + }; + + vreg_s8c_1p3: smps8 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_wcss_adcdac_1: + vdda_wcss_adcdac_22: + vreg_l2c_1p3: ldo2 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_hv_ebi0: + vdda_hv_ebi1: + vdda_hv_ebi2: + vdda_hv_ebi3: + vdda_hv_refgen0: + vdda_qlink_hv_ck: + vreg_l3c_1p2: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_5: + vreg_l4c_1p8: ldo4 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_6: + vreg_l5c_1p8: ldo5 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_2: + vreg_l6c_2p9: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c_3p0: ldo7 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c_2p9: ldo9 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + + vreg_l10c_3p3: ldo10 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11c_3p3: ldo11 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pm8009-rpmh-regulators { + compatible = "qcom,pm8009-rpmh-regulators"; + qcom,pmic-id = "f"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vreg_bob>; + + vdd-l2-supply = <&vreg_s8c_1p3>; + vdd-l5-l6-supply = <&vreg_bob>; + + vreg_l2f_1p2: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5f_2p85: ldo5 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6f_2p85: ldo6 { + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <2856000>; + }; + }; + }; &qupv3_id_1 {Signature · 1 line
2.20.1
Re: [PATCH v2 6/8] arm64: dts: qcom: sm8150-mtp: Add regulators
Quoted 5 lines · Niklas Cassel
Quoted 2 lines · Vinod Koul
Add the regulators found in the mtp platform. This platform consists of pmic PM8150, PM8150L and PM8009.
Is there a reason not to squash this this patch 5/8 ?
I typically like big chunks to split logically so that is the reason why I still kept this off from base dts one
Signature · 1 line
~Vinod
PATCH v2 7/8 arm64: dts: qcom: sm8150: Add reserved-memory regions
In reply to Vinod KoulAdd the reserved memory regions in SM8150
--- arch/arm64/boot/dts/qcom/sm8150.dtsi | 111 +++++++++++++++++++++++++++ 1 file changed, 111 insertions(+)
arch/arm64/boot/dts/qcom/sm8150.dtsi +111 -0
@@ -153,6 +153,117 @@ method = "smc"; }; + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + hyp_mem: memory@85700000 { + reg = <0x0 0x85700000 0x0 0x600000>; + no-map; + }; + + xbl_mem: memory@85d00000 { + reg = <0x0 0x85d00000 0x0 0x140000>; + no-map; + }; + + aop_mem: memory@85f00000 { + reg = <0x0 0x85f00000 0x0 0x20000>; + no-map; + }; + + aop_cmd_db: memory@85f20000 { + compatible = "qcom,cmd-db"; + reg = <0x0 0x85f20000 0x0 0x20000>; + no-map; + }; + + smem_mem: memory@86000000 { + reg = <0x0 0x86000000 0x0 0x200000>; + no-map; + }; + + tz_mem: memory@86200000 { + reg = <0x0 0x86200000 0x0 0x3900000>; + no-map; + }; + + rmtfs_mem: memory@89b00000 { + compatible = "qcom,rmtfs-mem"; + reg = <0x0 0x89b00000 0x0 0x200000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + + camera_mem: memory@8b700000 { + reg = <0x0 0x8b700000 0x0 0x500000>; + no-map; + }; + + wlan_mem: memory@8bc00000 { + reg = <0x0 0x8bc00000 0x0 0x180000>; + no-map; + }; + + npu_mem: memory@8bd80000 { + reg = <0x0 0x8bd80000 0x0 0x80000>; + no-map; + }; + + adsp_mem: memory@8be00000 { + reg = <0x0 0x8be00000 0x0 0x1a00000>; + no-map; + }; + + mpss_mem: memory@8d800000 { + reg = <0x0 0x8d800000 0x0 0x9600000>; + no-map; + }; + + venus_mem: memory@96e00000 { + reg = <0x0 0x96e00000 0x0 0x500000>; + no-map; + }; + + slpi_mem: memory@97300000 { + reg = <0x0 0x97300000 0x0 0x1400000>; + no-map; + }; + + ipa_fw_mem: memory@98700000 { + reg = <0x0 0x98700000 0x0 0x10000>; + no-map; + }; + + ipa_gsi_mem: memory@98710000 { + reg = <0x0 0x98710000 0x0 0x5000>; + no-map; + }; + + gpu_mem: memory@98715000 { + reg = <0x0 0x98715000 0x0 0x2000>; + no-map; + }; + + spss_mem: memory@98800000 { + reg = <0x0 0x98800000 0x0 0x100000>; + no-map; + }; + + cdsp_mem: memory@98900000 { + reg = <0x0 0x98900000 0x0 0x1400000>; + no-map; + }; + + qseecom_mem: memory@9e400000 { + reg = <0 0x9e400000 0 0x1400000>; + no-map; + }; + }; + soc: soc@0 { #address-cells = <1>; #size-cells = <1>;
Signature · 1 line
2.20.1
Re: [PATCH v2 7/8] arm64: dts: qcom: sm8150: Add reserved-memory regions
Quoted 1 line · Vinod Koul
Add the reserved memory regions in SM8150
Is there a reason not to squash this this patch 1/8 ?
Quoted 131 lines
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/sm8150.dtsi | 111 +++++++++++++++++++++++++++ 1 file changed, 111 insertions(+)arch/arm64/boot/dts/qcom/sm8150.dtsi +111
-0@@ -153,6 +153,117 @@ method = "smc"; }; + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + hyp_mem: memory@85700000 { + reg = <0x0 0x85700000 0x0 0x600000>; + no-map; + }; + + xbl_mem: memory@85d00000 { + reg = <0x0 0x85d00000 0x0 0x140000>; + no-map; + }; + + aop_mem: memory@85f00000 { + reg = <0x0 0x85f00000 0x0 0x20000>; + no-map; + }; + + aop_cmd_db: memory@85f20000 { + compatible = "qcom,cmd-db"; + reg = <0x0 0x85f20000 0x0 0x20000>; + no-map; + }; + + smem_mem: memory@86000000 { + reg = <0x0 0x86000000 0x0 0x200000>; + no-map; + }; + + tz_mem: memory@86200000 { + reg = <0x0 0x86200000 0x0 0x3900000>; + no-map; + }; + + rmtfs_mem: memory@89b00000 { + compatible = "qcom,rmtfs-mem"; + reg = <0x0 0x89b00000 0x0 0x200000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + + camera_mem: memory@8b700000 { + reg = <0x0 0x8b700000 0x0 0x500000>; + no-map; + }; + + wlan_mem: memory@8bc00000 { + reg = <0x0 0x8bc00000 0x0 0x180000>; + no-map; + }; + + npu_mem: memory@8bd80000 { + reg = <0x0 0x8bd80000 0x0 0x80000>; + no-map; + }; + + adsp_mem: memory@8be00000 { + reg = <0x0 0x8be00000 0x0 0x1a00000>; + no-map; + }; + + mpss_mem: memory@8d800000 { + reg = <0x0 0x8d800000 0x0 0x9600000>; + no-map; + }; + + venus_mem: memory@96e00000 { + reg = <0x0 0x96e00000 0x0 0x500000>; + no-map; + }; + + slpi_mem: memory@97300000 { + reg = <0x0 0x97300000 0x0 0x1400000>; + no-map; + }; + + ipa_fw_mem: memory@98700000 { + reg = <0x0 0x98700000 0x0 0x10000>; + no-map; + }; + + ipa_gsi_mem: memory@98710000 { + reg = <0x0 0x98710000 0x0 0x5000>; + no-map; + }; + + gpu_mem: memory@98715000 { + reg = <0x0 0x98715000 0x0 0x2000>; + no-map; + }; + + spss_mem: memory@98800000 { + reg = <0x0 0x98800000 0x0 0x100000>; + no-map; + }; + + cdsp_mem: memory@98900000 { + reg = <0x0 0x98900000 0x0 0x1400000>; + no-map; + }; + + qseecom_mem: memory@9e400000 { + reg = <0 0x9e400000 0 0x1400000>; + no-map; + }; + }; + soc: soc@0 { #address-cells = <1>; #size-cells = <1>;Signature · 1 line
2.20.1
PATCH v2 8/8 arm64: dts: qcom: sm8150: Add apps shared nodes
In reply to Vinod KoulAdd apss_shared and apps_rsc including the rpmhcc child node, pmu, SMEM nodes
--- arch/arm64/boot/dts/qcom/sm8150.dtsi | 63 ++++++++++++++++++++++++++++ 1 file changed, 63 insertions(+)
arch/arm64/boot/dts/qcom/sm8150.dtsi +63 -0
@@ -142,12 +142,23 @@ }; }; + tcsr_mutex: hwlock { + compatible = "qcom,tcsr-mutex"; + syscon = <&tcsr_mutex_regs 0 0x1000>; + #hwlock-cells = <1>; + }; + memory@80000000 { device_type = "memory"; /* We expect the bootloader to fill in the size */ reg = <0 0x80000000 0 0>; }; + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_HIGH>; + }; + psci { compatible = "arm,psci-1.0"; method = "smc";
@@ -264,6 +275,12 @@ }; }; + smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; + }; + soc: soc@0 { #address-cells = <1>; #size-cells = <1>;
@@ -303,6 +320,11 @@ }; }; + tcsr_mutex_regs: syscon@1f40000 { + compatible = "syscon"; + reg = <0x01f40000 0x40000>; + }; + tlmm: pinctrl@3100000 { compatible = "qcom,sm8150-pinctrl"; reg = <0x03100000 0x300000>,
@@ -318,6 +340,16 @@ #interrupt-cells = <2>; }; + aoss_qmp: power-controller@c300000 { + compatible = "qcom,sm8150-aoss-qmp"; + reg = <0x0c300000 0x100000>; + interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>; + mboxes = <&apss_shared 0>; + + #clock-cells = <0>; + #power-domain-cells = <1>; + }; + intc: interrupt-controller@17a00000 { compatible = "arm,gic-v3"; interrupt-controller;
@@ -327,6 +359,12 @@ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; }; + apss_shared: mailbox@17c00000 { + compatible = "qcom,sm8150-apss-shared"; + reg = <0x17c00000 0x1000>; + #mbox-cells = <1>; + }; + timer@17c20000 { #address-cells = <1>; #size-cells = <1>;
@@ -386,6 +424,31 @@ }; }; + apps_rsc: rsc@18200000 { + label = "apps_rsc"; + compatible = "qcom,rpmh-rsc"; + reg = <0x18200000 0x10000>, + <0x18210000 0x10000>, + <0x18220000 0x10000>; + reg-names = "drv-0", "drv-1", "drv-2"; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + qcom,tcs-offset = <0xd00>; + qcom,drv-id = <2>; + qcom,tcs-config = <ACTIVE_TCS 2>, + <SLEEP_TCS 1>, + <WAKE_TCS 1>, + <CONTROL_TCS 0>; + + rpmhcc: clock-controller { + compatible = "qcom,sm8150-rpmh-clk"; + #clock-cells = <1>; + clock-names = "xo"; + clocks = <&xo_board>; + }; + }; + spmi_bus: spmi@c440000 { compatible = "qcom,spmi-pmic-arb"; reg = <0x0c440000 0x0001100>,
Signature · 1 line
2.20.1
Quoted 10 lines · Vinod Koul
This series adds DTS for SM8150, PMIC PM8150, PM8150B, PM8150L and the MTP for SM8150.
Changes in v2:
- Squash patches
- Fix comments given by Stephen namely, lowercase for hext numbers, making rpmhcc havexo_boardas parent, rename pon controller to power-on controller, make pmic nodes as disabled etc.
- removed the dependency on clk defines and use raw numbers
Quoted 6 lines
Vinod Koul (8):
arm64: dts: qcom: sm8150: add base dts file
arm64: dts: qcom: pm8150: Add Base DTS file
arm64: dts: qcom: pm8150b: Add Base DTS file
arm64: dts: qcom: pm8150l: Add Base DTS file
arm64: dts: qcom: sm8150-mtp: add base dts file
Use consistent naming.
Quoted 20 lines
arm64: dts: qcom: sm8150-mtp: Add regulators
arm64: dts: qcom: sm8150: Add reserved-memory regions
arm64: dts: qcom: sm8150: Add apps shared nodesarch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/pm8150.dtsi | 95 +++++ arch/arm64/boot/dts/qcom/pm8150b.dtsi | 84 +++++ arch/arm64/boot/dts/qcom/pm8150l.dtsi | 78 ++++ arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 375 +++++++++++++++++++ arch/arm64/boot/dts/qcom/sm8150.dtsi | 479 ++++++++++++++++++++++++ 6 files changed, 1112 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pm8150.dtsi create mode 100644 arch/arm64/boot/dts/qcom/pm8150b.dtsi create mode 100644 arch/arm64/boot/dts/qcom/pm8150l.dtsi create mode 100644 arch/arm64/boot/dts/qcom/sm8150-mtp.dts create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsiSignature · 1 line
2.20.1
Quoted 11 lines · Niklas Cassel
Quoted 10 lines · Vinod Koul
This series adds DTS for SM8150, PMIC PM8150, PM8150B, PM8150L and the MTP for SM8150.
Changes in v2:
- Squash patches
- Fix comments given by Stephen namely, lowercase for hext numbers, making rpmhcc havexo_boardas parent, rename pon controller to power-on controller, make pmic nodes as disabled etc.
- removed the dependency on clk defines and use raw numbers
Quoted 8 lines
Quoted 6 lines
Vinod Koul (8):
arm64: dts: qcom: sm8150: add base dts file
arm64: dts: qcom: pm8150: Add Base DTS file
arm64: dts: qcom: pm8150b: Add Base DTS file
arm64: dts: qcom: pm8150l: Add Base DTS file
arm64: dts: qcom: sm8150-mtp: add base dts fileUse consistent naming.
Will do :)
Thanks for the review Niklas
Signature · 1 line
~Vinod