Skip to contentSkip to conversation

serial: 8250_pci: Add F81504A series Support

PATCH In review Ji-Ze Hong (Peter Hong) 3 participants 5 messages Aug 16, 2019 – Aug 23, 2019 TTY layer and serial drivers

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 serial: 8250_pci: Add F81504A series Support

Fintek F81504A/508A/512A is PCIE to 4/8/12 UARTs device. It's support IO/MMIO/PCIE conf to access all functions. The old F81504/508/512 is only support IO.

---
 drivers/tty/serial/8250/8250_pci.c | 121 +++++++++++++++++++++++++++++++++++++
 1 file changed, 121 insertions(+)
drivers/tty/serial/8250/8250_pci.c +121 -0
index c0d10a35bf70..80737862bbef 100644
@@ -43,6 +43,11 @@ struct pci_serial_quirk {
 	void	(*exit)(struct pci_dev *dev);
 };
 
+struct f815xxa_data {
+	spinlock_t lock;
+	int idx;
+};
+
 #define PCI_NUM_BAR_RESOURCES	6
 
 struct serial_private {
@@ -1707,6 +1712,77 @@ static int pci_fintek_init(struct pci_dev *dev)
 	return max_port;
 }
 
+static void f815xxa_mem_serial_out(struct uart_port *p, int offset, int value)
+{
+	struct f815xxa_data *data = p->private_data;
+	unsigned long flags;
+
+	spin_lock_irqsave(&data->lock, flags);
+	writeb(value, p->membase + offset);
+	readb(p->membase + UART_SCR); /* Dummy read for flush pcie tx queue */
+	spin_unlock_irqrestore(&data->lock, flags);
+}
+
+static int pci_fintek_f815xxa_setup(struct serial_private *priv,
+			    const struct pciserial_board *board,
+			    struct uart_8250_port *port, int idx)
+{
+	struct pci_dev *pdev = priv->dev;
+	struct f815xxa_data *data;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->idx = idx;
+	spin_lock_init(&data->lock);
+
+	port->port.private_data = data;
+	port->port.iotype = UPIO_MEM;
+	port->port.flags |= UPF_IOREMAP;
+	port->port.mapbase = pci_resource_start(pdev, 0) + 8 * idx;
+	port->port.serial_out = f815xxa_mem_serial_out;
+
+	return 0;
+}
+
+static int pci_fintek_f815xxa_init(struct pci_dev *dev)
+{
+	u32 max_port, i;
+	int config_base;
+
+	if (!(pci_resource_flags(dev, 0) & IORESOURCE_MEM))
+		return -ENODEV;
+
+	switch (dev->device) {
+	case 0x1204: /* 4 ports */
+	case 0x1208: /* 8 ports */
+		max_port = dev->device & 0xff;
+		break;
+	case 0x1212: /* 12 ports */
+		max_port = 12;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* Set to mmio decode */
+	pci_write_config_byte(dev, 0x209, 0x40);
+
+	for (i = 0; i < max_port; ++i) {
+		/* UART0 configuration offset start from 0x2A0 */
+		config_base = 0x2A0 + 0x08 * i;
+
+		/* Select 128-byte FIFO and 8x FIFO threshold */
+		pci_write_config_byte(dev, config_base + 0x01, 0x33);
+
+		/* Enable UART I/O port */
+		pci_write_config_byte(dev, config_base + 0, 0x01);
+	}
+
+	return max_port;
+}
+
 static int skip_tx_en_setup(struct serial_private *priv,
 			const struct pciserial_board *board,
 			struct uart_8250_port *port, int idx)
@@ -2781,6 +2857,30 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.setup		= pci_fintek_setup,
 		.init		= pci_fintek_init,
 	},
+	{
+		.vendor		= 0x1c29,
+		.device		= 0x1204,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.setup		= pci_fintek_f815xxa_setup,
+		.init		= pci_fintek_f815xxa_init,
+	},
+	{
+		.vendor		= 0x1c29,
+		.device		= 0x1208,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.setup		= pci_fintek_f815xxa_setup,
+		.init		= pci_fintek_f815xxa_init,
+	},
+	{
+		.vendor		= 0x1c29,
+		.device		= 0x1212,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.setup		= pci_fintek_f815xxa_setup,
+		.init		= pci_fintek_f815xxa_init,
+	},
 
 	/*
 	 * Default "match everything" terminator entry
@@ -2976,6 +3076,9 @@ enum pci_board_num_t {
 	pbn_fintek_4,
 	pbn_fintek_8,
 	pbn_fintek_12,
+	pbn_fintek_F81504A,
+	pbn_fintek_F81508A,
+	pbn_fintek_F81512A,
 	pbn_wch382_2,
 	pbn_wch384_4,
 	pbn_pericom_PI7C9X7951,
@@ -3732,6 +3835,21 @@ static struct pciserial_board pci_boards[] = {
 		.base_baud	= 115200,
 		.first_offset	= 0x40,
 	},
+	[pbn_fintek_F81504A] = {
+		.num_ports	= 4,
+		.uart_offset	= 8,
+		.base_baud	= 115200,
+	},
+	[pbn_fintek_F81508A] = {
+		.num_ports	= 8,
+		.uart_offset	= 8,
+		.base_baud	= 115200,
+	},
+	[pbn_fintek_F81512A] = {
+		.num_ports	= 12,
+		.uart_offset	= 8,
+		.base_baud	= 115200,
+	},
 	[pbn_wch382_2] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 2,
@@ -5634,6 +5752,9 @@ static const struct pci_device_id serial_pci_tbl[] = {
 	{ PCI_DEVICE(0x1c29, 0x1104), .driver_data = pbn_fintek_4 },
 	{ PCI_DEVICE(0x1c29, 0x1108), .driver_data = pbn_fintek_8 },
 	{ PCI_DEVICE(0x1c29, 0x1112), .driver_data = pbn_fintek_12 },
+	{ PCI_DEVICE(0x1c29, 0x1204), .driver_data = pbn_fintek_F81504A },
+	{ PCI_DEVICE(0x1c29, 0x1208), .driver_data = pbn_fintek_F81508A },
+	{ PCI_DEVICE(0x1c29, 0x1212), .driver_data = pbn_fintek_F81512A },
 
 	/* MKS Tenta SCOM-080x serial cards */
 	{ PCI_DEVICE(0x1601, 0x0800), .driver_data = pbn_b0_4_1250000 },
Signature · 1 line
2.7.4
#1 lore raw
Quoted 3 lines · Ji-Ze Hong (Peter Hong)

Fintek F81504A/508A/512A is PCIE to 4/8/12 UARTs device. It's support IO/MMIO/PCIE conf to access all functions. The old F81504/508/512 is only support IO.

We have 8250_fintek.
Isn't it a right place to add these?

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#2 lore raw

Hi,

Andy Shevchenko 於 2019/8/16 下午 07:26 寫道:

Quoted 8 lines · Ji-Ze Hong (Peter Hong)
Quoted 3 lines

Fintek F81504A/508A/512A is PCIE to 4/8/12 UARTs device. It's support IO/MMIO/PCIE conf to access all functions. The old F81504/508/512 is only support IO.

We have 8250_fintek.
Isn't it a right place to add these?

The 8250_fintek implements PNP device with id PNP0501. Should I also implements PCIe device in this file?

Signature · 2 lines
With Best Regards,
Peter Hong
maintainer
#3 lore raw
Quoted 8 lines · Ji-Ze Hong (Peter Hong)

Hi,

Andy Shevchenko 於 2019/8/16 下午 07:26 寫道:

Quoted 5 lines · Ji-Ze Hong (Peter Hong)
Quoted 3 lines

Fintek F81504A/508A/512A is PCIE to 4/8/12 UARTs device. It's support IO/MMIO/PCIE conf to access all functions. The old F81504/508/512 is only support IO.

Quoted 6 lines
Quoted 3 lines

We have 8250_fintek.
Isn't it a right place to add these?

The 8250_fintek implements PNP device with id PNP0501. Should I also implements PCIe device in this file?

Does it use the same logic? If so, that makes sense, but if you can not share anything, then no, it does not make sense.

thanks,

greg k-h

#4 lore raw

Hi,

Greg KH 於 2019/8/23 上午 05:15 寫道:

Quoted 11 lines
Quoted 7 lines

Andy Shevchenko 於 2019/8/16 下午 07:26 寫道:

Quoted 3 lines

We have 8250_fintek.
Isn't it a right place to add these?

The 8250_fintek implements PNP device with id PNP0501. Should I also implements PCIe device in this file?

Does it use the same logic? If so, that makes sense, but if you can not share anything, then no, it does not make sense.

It's same with old series F81504/508/512 and the old series had implement in 8250_pci.c (pbn_fintek_4/pbn_fintek_8/pbn_fintek_12). So I decide implements the new series in 8250_pci.c

Thanks

Signature · 2 lines
With Best Regards,
Peter Hong