Skip to contentSkip to conversation

ASoC: rt1011: ADCDAT pin config modification

PATCH In review [email protected] 2 participants 5 messages Aug 26, 2019 – Aug 30, 2019 1 message not in the archive

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 2/2 ASoC: rt1011: ADCDAT pin config modification

From: Shuming Fan <[email protected]>

ADCDAT pin config sets to output mode in default.
And the driver creates the kcontrol to control ADCDAT pin configuration.

---
 sound/soc/codecs/rt1011.c | 18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)
sound/soc/codecs/rt1011.c +15 -3
index f9235764ad32..52c17450d5a0 100644
@@ -1029,6 +1029,14 @@ static SOC_ENUM_SINGLE_DECL(rt1011_tdm_adc1_1_enum,	RT1011_TDM1_SET_3, 6,
 static SOC_ENUM_SINGLE_DECL(rt1011_tdm_adc2_1_enum,	RT1011_TDM1_SET_3, 4,
 	rt1011_tdm_adc_swap_select);
 
+static const char * const rt1011_adcdat_pin_config_select[] = {
+	"Output", "Input"
+};
+static SOC_ENUM_SINGLE_DECL(rt1011_adcdat1_pin_config_enum, RT1011_TDM_TOTAL_SET, 4,
+	rt1011_adcdat_pin_config_select);
+static SOC_ENUM_SINGLE_DECL(rt1011_adcdat2_pin_config_enum, RT1011_TDM_TOTAL_SET, 3,
+	rt1011_adcdat_pin_config_select);
+
 static void rt1011_reset(struct regmap *regmap)
 {
 	regmap_write(regmap, RT1011_RESET, 0);
@@ -1343,6 +1351,8 @@ static const struct snd_kcontrol_new rt1011_snd_controls[] = {
 	SOC_ENUM("I2S ADC DOUT Mode", rt1011_adc_dout_mode_enum),
 	SOC_ENUM("TDM1 DOUT Length", rt1011_tdm1_dout_len_enum),
 	SOC_ENUM("TDM2 DOUT Length", rt1011_tdm2_dout_len_enum),
+	SOC_ENUM("ADCDAT1 Pin Config", rt1011_adcdat1_pin_config_enum),
+	SOC_ENUM("ADCDAT2 Pin Config", rt1011_adcdat2_pin_config_enum),
 
 	/* Speaker/Receiver Mode */
 	SOC_SINGLE_EXT("RECV SPK Mode", SND_SOC_NOPM, 0, 1, 0,
@@ -1859,9 +1869,6 @@ static int rt1011_set_tdm_slot(struct snd_soc_dai *dai,
 		RT1011_TDM_I2S_DOCK_EN_1_MASK,	tdm_en);
 	snd_soc_component_update_bits(component, RT1011_TDM2_SET_2,
 		RT1011_TDM_I2S_DOCK_EN_2_MASK,	tdm_en);
-	snd_soc_component_update_bits(component, RT1011_TDM_TOTAL_SET,
-		RT1011_ADCDAT1_PIN_CONFIG | RT1011_ADCDAT2_PIN_CONFIG,
-		RT1011_ADCDAT1_OUTPUT | RT1011_ADCDAT2_OUTPUT);
 
 	snd_soc_dapm_mutex_unlock(dapm);
 	return ret;
@@ -2207,6 +2214,11 @@ static void rt1011_calibration_work(struct work_struct *work)
 
 	/* initial */
 	rt1011_reg_init(component);
+
+	/* set ADCDAT to output mode */
+	snd_soc_component_update_bits(component, RT1011_TDM_TOTAL_SET,
+		RT1011_ADCDAT1_PIN_CONFIG | RT1011_ADCDAT2_PIN_CONFIG,
+		RT1011_ADCDAT1_OUTPUT | RT1011_ADCDAT2_OUTPUT);
 }
 
 static int rt1011_i2c_probe(struct i2c_client *i2c,
Signature · 1 line
2.23.0
maintainer
#1 lore raw
Quoted 4 lines · On Mon, Aug 26, 2019 at 05:01:20PM +0800, [email protected] wrote:

From: Shuming Fan <[email protected]>

ADCDAT pin config sets to output mode in default.
And the driver creates the kcontrol to control ADCDAT pin configuration.

Why would this change at runtime? I'd expect this to be controlled by the machine driver or a DT property.

A message that is not in the archive (sent off-list or not yet received): 10317AB43303BA4884D7AF9C2EBCFF4002BE5727@RTITMBSVM07.realtek.com.tw

maintainer
#3 lore raw
Quoted 8 lines · Shuming [范書銘]
Quoted 5 lines
Quoted 2 lines

ADCDAT pin config sets to output mode in default.
And the driver creates the kcontrol to control ADCDAT pin configuration.

Why would this change at runtime? I'd expect this to be controlled by the machine driver or a DT property.

It will not change at runtime in the normal case.
I think we may use it to test the feedback signal in factory mode.

So really this is setting up a loopback for testing?

#4 lore raw
Quoted 10 lines
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

ADCDAT pin config sets to output mode in default.
And the driver creates the kcontrol to control ADCDAT pin configuration.

Why would this change at runtime? I'd expect this to be controlled by the machine driver or a DT property.

It will not change at runtime in the normal case.
I think we may use it to test the feedback signal in factory mode.

So really this is setting up a loopback for testing?

We would not like to change ADCDAT pin to input mode in normal case. That's why the driver enables ADCDAT pin to the output mode in default. The rt1011 supports the feedback signal which could be playback data or I/V data, etc. If the system wants the AEC reference data, rt1011 could feedback the playback data.

The product could connect 2/4/6/8 rt1011 chips on the same I2S bus. In a test or debug mode, we could toggle ADCDAT pin to input mode that also helps HW engineer check the slot of feedback signal for each rt1011.

Quoted 1 line

------Please consider the environment before printing this e-mail.

maintainer
#5 lore raw
Quoted 10 lines · Shuming [范書銘]
Quoted 1 line

So really this is setting up a loopback for testing?

We would not like to change ADCDAT pin to input mode in normal case. That's why the driver enables ADCDAT pin to the output mode in default. The rt1011 supports the feedback signal which could be playback data or I/V data, etc. If the system wants the AEC reference data, rt1011 could feedback the playback data.

The product could connect 2/4/6/8 rt1011 chips on the same I2S bus. In a test or debug mode, we could toggle ADCDAT pin to input mode that also helps HW engineer check the slot of feedback signal for each rt1011.

I think this needs more than just a straight userspace control on one device, these use cases make sense but they'll need to be configured over multiple chips simultaneously otherwise there's some possibility of hardware damage (eg, if two chips try to drive the signal at the same time). If this really can be usefully varied at runtime then the driver bit of this should probably be an API that the machine driver can call, the machine driver can then expose a control that sets all the chips involved up together.