Error reading cluster" from fs/fat/fat.c
Hello list,
I have a annoying problem with u-boot 2019.07. I try to boot a Linux Image from a fat16 partition on a SD-Card. But I got the "Error reading cluster" Message from fs/fat/fat.c
=> boot
switch to partitions #0, OK
mmc2 is current device
Error reading cluster
** Unable to read file Image **
=> mmc part
Partition Map for MMC device 2 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type 1 16384 266240 d38187c8-01 06 2 282624 7491584 d38187c8-02 83
After some debugging I end up in blk_dread() from drivers/block/blk-uclass.c
blks_read = ops->read(dev, start, blkcnt, buffer);
here I got blks_read=0 which seems is the cause for the "Error reading cluster" later in get_cluster().
Here a Debug Trace with some variables printed out:
...get_fatent() FAT16: entry: 0x0000595c = 22876, offset: 0x055c = 1372 get_fatent() FAT16: ret: 0x0000595d, entry: 0x0000595c, offset: 0x055c get_cluster() gc - clustnum: 16813, startsect: 134800blkcache_read() miss: start 24e90, count 48513blk_dread() dev=fd6ebaa0blk_dread() start=24e90blk_dread() blkcnt=48513blk_dread() buffer=80280000blk_find_device() blk_find_device: if_type=6, devnum=2: usdhc at 5b010000.blk, 6, 0 blk_find_device() blk_find_device: if_type=6, devnum=2: usdhc at 5b030000.blk, 6, 2 blk_dread() blks_read=0blk_dread() blkcnt=48513disk_read() ret=0disk_read() nr_blocks=48513get_cluster() Error reading data (got -1) 2get_cluster() ret=-1get_cluster() idx=48513
Error reading cluster 2
** Unable to read file Image **
Can somebody help me to find the cause of this problem? Is something with my fat partion or partition table wrong or do I hit a bug?
Best regards,
Oliver
Quoted 18 lines · Oliver Graute
Hello list,
I have a annoying problem with u-boot 2019.07. I try to boot a Linux Image from a fat16 partition on a SD-Card. But I got the "Error reading cluster" Message from
fs/fat/fat.c=> boot
switch to partitions #0, OK
mmc2 is current device
Error reading cluster
** Unable to read file Image **=> mmc part
Partition Map for MMC device 2 -- Partition Type: DOSPart Start Sector Num Sectors UUID Type 1 16384 266240 d38187c8-01 06 2 282624 7491584 d38187c8-02 83
Quoted 6 lines
After some debugging I end up in
blk_dread()fromdrivers/block/blk-uclass.c
blks_read=ops->read(dev, start, blkcnt, buffer);here I got blks_read=0 which seems is the cause for the "Error reading cluster" later in
get_cluster().
After some more digging I found out that this error is related to the file size. I can fatload files up to 16MB but no files with 24MB like the Kernel Image. Is there some limitation somewhere?
U-Boot 2019.07-00001-g1c0a4f90ca-dirty (Aug 26 2019 - 08:36:06 +0200)
CPU: NXP i.MX8QM RevB A53 at 1200 MHz
Model: Advantech iMX8QM Qseven series Board: ROM-7720-A1 4GB Build: SCFW 65afe5f6 Boot: SD2 DRAM: 3.9 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial at 5a060000 Out: serial at 5a060000 Err: serial at 5a060000 Net: eth0: ethernet at 5b040000Could not get PHY for FEC1: addr 1
, eth-1: ethernet at 5b050000
Hit any key to stop autoboot: 0
=> fatls mmc 2:1
dtbs/
24838656 Image
10671566 Image.gz
18734584 initramfs-linux-fallback.img
7263143 initramfs-linux.img
19136 imx8qm-rom7720-a1.dtb
102464 hdmitxfw.bin
1048576 1mb.txt
2097152 2MB.txt
524288 512kb.txt
786432 768kb.txt
16777216 16MB.txt
25165824 24MB.txt
4194304 4MB.txt
8388608 8MB.txt14 file(s), 1 dir(s)
=> fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} 512kb.txt 524288 bytes read in 33 ms (15.2 MiB/s)
=> fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} 768kb.txt 786432 bytes read in 43 ms (17.4 MiB/s)
=> fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} 1mb.txt 1048576 bytes read in 58 ms (17.2 MiB/s)
=> fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} 2mb.txt 2097152 bytes read in 98 ms (20.4 MiB/s)
=> fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} 4mb.txt 4194304 bytes read in 190 ms (21.1 MiB/s)
=> fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} 8mb.txt 8388608 bytes read in 365 ms (21.9 MiB/s)
=> fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} 16mb.txt 16777216 bytes read in 724 ms (22.1 MiB/s)
=> fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} 24mb.txt Error reading cluster 3
** Unable to read file 24mb.txt **
=>
Best regards,
Oliver
Quoted 7 lines · Oliver Graute
Quoted 6 lines · Oliver Graute
Hello list,
I have a annoying problem with u-boot 2019.07. I try to boot a Linux Image from a fat16 partition on a SD-Card. But I got the "Error reading cluster" Message from
fs/fat/fat.c
Quoted 5 lines
Quoted 5 lines
=> boot
switch to partitions #0, OK
mmc2 is current device
Error reading cluster
** Unable to read file Image **
this error occurs especially on this Swissbit SD-Card (industrial card)
=> mmcinfo
Device: FSL_SDHC
Manufacturer ID: 5d
OEM: 5342
Name: L1BM1
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 3.7 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
another San-Disk SD-Card (consumer) I tried is working fine with same u-boot image. So it looks for me for a wired hw/timing issue.
=> mmcinfo
Device: FSL_SDHC
Manufacturer ID: 13
OEM: 14e
Name: Q2J55
Bus Speed: 52000000
Mode: MMC High Speed (52MHz)
Rd Block Len: 512
MMC version 5.0
High Capacity: Yes
Capacity: 7.1 GiB
Bus Width: 8-bit
Erase Group Size: 512 KiB
HC WP Group Size: 8 MiB
User Capacity: 7.1 GiB WRREL
Boot Capacity: 16 MiB ENH
RPMB Capacity: 4 MiB ENH
Best Regards,
Oliver