Skip to contentSkip to conversation

ARM: omap3: Enable HWMODS for HW Random Number Generator

RFC In review Adam Ford 4 participants 15 messages Aug 28, 2019 – Oct 22, 2019

Subsystems (5)
lore
Share & tools
lore

Adam Ford

author
#0 lore raw

RFC 1/1 ARM: omap3: Enable HWMODS for HW Random Number Generator

The datasheet for the AM3517 shows the RNG is connected to L4. It shows the module address for the RNG is 0x480A0000, and it matches the omap2.dtsi description. Since the driver can support omap2 and omap4, it seems reasonable to assume the omap3 would use the same core for the RNG.

This RFC, mimics much of the omap2 hwmods on the OMAP3. It also adds the necessary clock for driving the RNG. Unfortunately, it appears non-functional. If anyone has any suggestions on how to finish the hwmod (or port it to the newer l4 device tree format), feedback is requested.

Currently the hwmods repond as follows:

[    0.245697] omap_hwmod: rng: _wait_target_ready failed: -22
[    0.245727] omap_hwmod: rng: cannot be enabled for reset (3)
[    6.780792] omap_hwmod: rng: _wait_target_ready failed: -22
arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi +1 -1
index 945537aee3ca..05891dff7fa1 100644
@@ -189,7 +189,7 @@
 			 <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>,
 			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
 			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
-			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>,
+			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, <&rng_ick>,
 			 <&ssi_ick>;
 	};
 };
arch/arm/mach-omap2/cm-regbits-34xx.h +1 -0
index 037529a9e969..82330a66e35c 100644
@@ -17,6 +17,7 @@
 #define OMAP3430_CLKACTIVITY_IVA2_MASK			(1 << 0)
 #define OMAP3430_CLKTRCTRL_MPU_MASK			(0x3 << 0)
 #define OMAP3430_ST_AES2_SHIFT				28
+#define OMAP34XX_ST_RNG_SHIFT                           2
 #define OMAP3430_ST_SHA12_SHIFT				27
 #define AM35XX_ST_UART4_SHIFT				23
 #define OMAP3430_ST_HDQ_SHIFT				22
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +45 -0

69 lines not on this page · raw message

Signature · 1 line
2.17.1
maintainer
#1 lore raw

Hi,

Quoted 11 lines · Adam Ford

The datasheet for the AM3517 shows the RNG is connected to L4. It shows the module address for the RNG is 0x480A0000, and it matches the omap2.dtsi description. Since the driver can support omap2 and omap4, it seems reasonable to assume the omap3 would use the same core for the RNG.

This RFC, mimics much of the omap2 hwmods on the OMAP3. It also adds the necessary clock for driving the RNG. Unfortunately, it appears non-functional. If anyone has any suggestions on how to finish the hwmod (or port it to the newer l4 device tree format), feedback is requested.

Yup I'll take the bait :) The patch below seems to do the trick for me on dm3730 based on translating your patch to probe with ti-sysc.

Not sure about 34xx, it seems we're missing rng_clk? Care to give it a try and attempt simlar patches for 34xx and 3517?

At least I'm not needing the "ti,no-reset-on-init" property that your patch has a comment for. Maybe that's needed on some other omap3.

Oh and this needs to default to status = "disabled" for HS devices like n900 as it needs to use the omap3-rom-rng.

Regards,

Tony

8< -----------------------

arch/arm/boot/dts/omap36xx.dtsi +23 -0
@@ -140,6 +140,29 @@
 			};
 		};
 
+		rng_target: target-module@480a0000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x480a003c 0x4>,
+			      <0x480a0040 0x4>,
+			      <0x480a0044 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>;
+			ti,syss-mask = <1>;
+			clocks = <&rng_ick>;
+			clock-names = "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x480a0000 0x2000>;
+
+			rng: rng@0 {
+				compatible = "ti,omap2-rng";
+				reg = <0x0 0x2000>;
+				interrupts = <52>;
+			};
+		};
+
 		/*
 		 * Note that the sysconfig register layout is a subset of the
 		 * "ti,sysc-omap4" type register with just sidle and midle bits
author
#2 lore raw
Quoted 56 lines · Tony Lindgren

Hi,

Quoted 11 lines · Adam Ford

The datasheet for the AM3517 shows the RNG is connected to L4. It shows the module address for the RNG is 0x480A0000, and it matches the omap2.dtsi description. Since the driver can support omap2 and omap4, it seems reasonable to assume the omap3 would use the same core for the RNG.

This RFC, mimics much of the omap2 hwmods on the OMAP3. It also adds the necessary clock for driving the RNG. Unfortunately, it appears non-functional. If anyone has any suggestions on how to finish the hwmod (or port it to the newer l4 device tree format), feedback is requested.

Yup I'll take the bait :) The patch below seems to do the trick for me on dm3730 based on translating your patch to probe with ti-sysc.

Not sure about 34xx, it seems we're missing rng_clk? Care to give it a try and attempt simlar patches for 34xx and 3517?

At least I'm not needing the "ti,no-reset-on-init" property that your patch has a comment for. Maybe that's needed on some other omap3.

Oh and this needs to default to status = "disabled" for HS devices like n900 as it needs to use the omap3-rom-rng.

Regards,

Tony

8< -----------------------

arch/arm/boot/dts/omap36xx.dtsi +13 -0
@@ -140,6 +140,29 @@
                        };
                };
 
+               rng_target: target-module@480a0000 {
+                       compatible = "ti,sysc-omap2", "ti,sysc";
+                       reg = <0x480a003c 0x4>,
+                             <0x480a0040 0x4>,
+                             <0x480a0044 0x4>;
+                       reg-names = "rev", "sysc", "syss";
+                       ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
+                       ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+                                       <SYSC_IDLE_NO>;
+                       ti,syss-mask = <1>;
+                       clocks = <&rng_ick>;
+                       clock-names = "ick";
+                       #address-cells = <1>;

arch/arm/boot/dts/omap36xx.dtsi line 165

Quoted 10 lines
arch/arm/boot/dts/omap36xx.dtsi +10 -0
+                       #size-cells = <1>;
+                       ranges = <0 0x480a0000 0x2000>;
+
+                       rng: rng@0 {
+                               compatible = "ti,omap2-rng";
+                               reg = <0x0 0x2000>;
+                               interrupts = <52>;
+                       };
+               };
+

Tony,

Can you tell me what branch you're using? I am not seeing the note below, so I am not exactly sure what version to base my testing.

ada,

Quoted 3 lines
arch/arm/boot/dts/omap36xx.dtsi +0 -0
                /*
                 * Note that the sysconfig register layout is a subset of the
                 * "ti,sysc-omap4" type register with just sidle and midle bits
author
#3 lore raw
Quoted 60 lines · Adam Ford
Quoted 58 lines · Tony Lindgren

Hi,

Quoted 11 lines · Adam Ford

The datasheet for the AM3517 shows the RNG is connected to L4. It shows the module address for the RNG is 0x480A0000, and it matches the omap2.dtsi description. Since the driver can support omap2 and omap4, it seems reasonable to assume the omap3 would use the same core for the RNG.

This RFC, mimics much of the omap2 hwmods on the OMAP3. It also adds the necessary clock for driving the RNG. Unfortunately, it appears non-functional. If anyone has any suggestions on how to finish the hwmod (or port it to the newer l4 device tree format), feedback is requested.

Yup I'll take the bait :) The patch below seems to do the trick for me on dm3730 based on translating your patch to probe with ti-sysc.

Not sure about 34xx, it seems we're missing rng_clk? Care to give it a try and attempt simlar patches for 34xx and 3517?

At least I'm not needing the "ti,no-reset-on-init" property that your patch has a comment for. Maybe that's needed on some other omap3.

Oh and this needs to default to status = "disabled" for HS devices like n900 as it needs to use the omap3-rom-rng.

Regards,

Tony

8< -----------------------

arch/arm/boot/dts/omap36xx.dtsi +15 -0
@@ -140,6 +140,29 @@
                        };
                };
 
+               rng_target: target-module@480a0000 {
+                       compatible = "ti,sysc-omap2", "ti,sysc";
+                       reg = <0x480a003c 0x4>,
+                             <0x480a0040 0x4>,
+                             <0x480a0044 0x4>;
+                       reg-names = "rev", "sysc", "syss";
+                       ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
+                       ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+                                       <SYSC_IDLE_NO>;
+                       ti,syss-mask = <1>;
+                       clocks = <&rng_ick>;
+                       clock-names = "ick";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+                       ranges = <0 0x480a0000 0x2000>;
Quoted 8 lines

arch/arm/boot/dts/omap36xx.dtsi line 165

Quoted 8 lines
arch/arm/boot/dts/omap36xx.dtsi +8 -0
+
+                       rng: rng@0 {
+                               compatible = "ti,omap2-rng";
+                               reg = <0x0 0x2000>;
+                               interrupts = <52>;
+                       };
+               };
+

I applied this on 5.3 and it is working. I assume the same is true in for-next.

Do you want to submit a formal patch? I can mark it as 'tested-by' This really helps speed up the startup sequence on boards with sshd because it delays for nearly 80 seconds waiting for entropy without the hwrng.

adam

Quoted 10 lines

Tony,

Can you tell me what branch you're using? I am not seeing the note below, so I am not exactly sure what version to base my testing.

ada,

Quoted 3 lines
arch/arm/boot/dts/omap36xx.dtsi +0 -0
                /*
                 * Note that the sysconfig register layout is a subset of the
                 * "ti,sysc-omap4" type register with just sidle and midle bits
#4 lore raw
Quoted 72 lines · On Monday 09 September 2019 08:37:09 Adam Ford wrote:
Quoted 60 lines · Adam Ford
Quoted 58 lines · Tony Lindgren

Hi,

Quoted 11 lines · Adam Ford

The datasheet for the AM3517 shows the RNG is connected to L4. It shows the module address for the RNG is 0x480A0000, and it matches the omap2.dtsi description. Since the driver can support omap2 and omap4, it seems reasonable to assume the omap3 would use the same core for the RNG.

This RFC, mimics much of the omap2 hwmods on the OMAP3. It also adds the necessary clock for driving the RNG. Unfortunately, it appears non-functional. If anyone has any suggestions on how to finish the hwmod (or port it to the newer l4 device tree format), feedback is requested.

Yup I'll take the bait :) The patch below seems to do the trick for me on dm3730 based on translating your patch to probe with ti-sysc.

Not sure about 34xx, it seems we're missing rng_clk? Care to give it a try and attempt simlar patches for 34xx and 3517?

At least I'm not needing the "ti,no-reset-on-init" property that your patch has a comment for. Maybe that's needed on some other omap3.

Oh and this needs to default to status = "disabled" for HS devices like n900 as it needs to use the omap3-rom-rng.

Regards,

Tony

8< -----------------------

arch/arm/boot/dts/omap36xx.dtsi +15 -0
@@ -140,6 +140,29 @@
                        };
                };
 
+               rng_target: target-module@480a0000 {
+                       compatible = "ti,sysc-omap2", "ti,sysc";
+                       reg = <0x480a003c 0x4>,
+                             <0x480a0040 0x4>,
+                             <0x480a0044 0x4>;
+                       reg-names = "rev", "sysc", "syss";
+                       ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
+                       ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+                                       <SYSC_IDLE_NO>;
+                       ti,syss-mask = <1>;
+                       clocks = <&rng_ick>;
+                       clock-names = "ick";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+                       ranges = <0 0x480a0000 0x2000>;
Quoted 8 lines

arch/arm/boot/dts/omap36xx.dtsi line 165

Quoted 8 lines
arch/arm/boot/dts/omap36xx.dtsi +8 -0
+
+                       rng: rng@0 {
+                               compatible = "ti,omap2-rng";
+                               reg = <0x0 0x2000>;
+                               interrupts = <52>;
+                       };
+               };
+

I applied this on 5.3 and it is working. I assume the same is true in for-next.

Quoted 4 lines

Do you want to submit a formal patch? I can mark it as 'tested-by' This really helps speed up the startup sequence on boards with sshd because it delays for nearly 80 seconds waiting for entropy without the hwrng.

Hi! When applying a patch, could you please disable this rng for n900?

In omap3-n900.dts for rng should be status = "disabled" (as Tony already wrote), similarly like for aes.

Thanks!

Quoted 11 lines

adam

Quoted 10 lines

Tony,

Can you tell me what branch you're using? I am not seeing the note below, so I am not exactly sure what version to base my testing.

ada,

Quoted 3 lines
arch/arm/boot/dts/omap36xx.dtsi +0 -0
                /*
                 * Note that the sysconfig register layout is a subset of the
                 * "ti,sysc-omap4" type register with just sidle and midle bits
Signature · 2 lines
Pali Rohár
[email protected]
maintainer
#5 lore raw
Quoted 2 lines · Pali Rohár
Quoted 1 line · On Monday 09 September 2019 08:37:09 Adam Ford wrote:

I applied this on 5.3 and it is working. I assume the same is true in for-next.

Hmm I noticed I stopped getting RNG data after several rmmod modprobe cycles, or several hd /dev/random reads. Anybody else seeing that?

Quoted 9 lines
Quoted 4 lines

Do you want to submit a formal patch? I can mark it as 'tested-by' This really helps speed up the startup sequence on boards with sshd because it delays for nearly 80 seconds waiting for entropy without the hwrng.

Hi! When applying a patch, could you please disable this rng for n900?

In omap3-n900.dts for rng should be status = "disabled" (as Tony already wrote), similarly like for aes.

Yeah I'll post a proper patch after -rc1.

Regards,

Tony

author
#6 lore raw
Quoted 7 lines · Tony Lindgren
Quoted 2 lines · Pali Rohár
Quoted 1 line · On Monday 09 September 2019 08:37:09 Adam Ford wrote:

I applied this on 5.3 and it is working. I assume the same is true in for-next.

Hmm I noticed I stopped getting RNG data after several rmmod modprobe cycles, or several hd /dev/random reads. Anybody else seeing that?

On the Logic PD Torpedo, I was able to read from /dev/hwrng and /dev/random 10x without issue
I have installed rng-tools and I have sshd running and some other stuff that might get in the way if I do an rmmod too much, but I removed and modprobed the omap-rng 3x and never saw an issue reading either /dev/hwrng or /dev/random.

I have been meaning to test this on the AM3517 and haven't gotten to it yet, but I assume you've only tested omap3630, is that true?

adam

Quoted 8 lines
Quoted 8 lines
Quoted 5 lines

Do you want to submit a formal patch? I can mark it as 'tested-by' This really helps speed up the startup sequence on boards with sshd because it delays for nearly 80 seconds waiting for entropy without the hwrng.

Hi! When applying a patch, could you please disable this rng for n900?

Quoted 8 lines
Quoted 2 lines

In omap3-n900.dts for rng should be status = "disabled" (as Tony already wrote), similarly like for aes.

Yeah I'll post a proper patch after -rc1.

Regards,

Tony

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

author
#7 lore raw
In reply to Tony Lindgren
Quoted 13 lines · Tony Lindgren
Quoted 2 lines · Pali Rohár
Quoted 1 line · On Monday 09 September 2019 08:37:09 Adam Ford wrote:

I applied this on 5.3 and it is working. I assume the same is true in for-next.

Hmm I noticed I stopped getting RNG data after several rmmod modprobe cycles, or several hd /dev/random reads. Anybody else seeing that?

Quoted 5 lines
Quoted 4 lines

Do you want to submit a formal patch? I can mark it as 'tested-by' This really helps speed up the startup sequence on boards with sshd because it delays for nearly 80 seconds waiting for entropy without the hwrng.

Quoted 6 lines
Quoted 4 lines

Hi! When applying a patch, could you please disable this rng for n900?

In omap3-n900.dts for rng should be status = "disabled" (as Tony already wrote), similarly like for aes.

Yeah I'll post a proper patch after -rc1.

FYI,

By putting your node into omap34xx.dtsi and omap36xx.dtsi along with the following, I can get the RNG to work on an OMAP3530 and a DM3730.

(quoted diff) +0 -0

b/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi
index 5e9d1afcd422..73f351e6d132 100644

arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi +1 -1
@@ -259,7 +259,7 @@
                         <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
                         <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
                         <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, <&icr_ick>,
-                        <&des2_ick>, <&mspro_ick>, <&mailboxes_ick>,
+                        <&des2_ick>, <&mspro_ick>, <&mailboxes_ick>,

<&rng_ick>,

                         <&mspro_fck>;
        };

};

I tried doing the same for am3517, but it doesn't appear to work. In fact, the board hangs at boot with no splat, so I assume that some clock isn't running and causing a hang. Figure 4-50 in the AM3517 TRM shows the security_l4_iclk2, so I wonder if the HW mods for AES, SHA, etc are doing something to enable this clock. Those HWmods are disabled on AM3517. I tried turning on the hwmods for them before without success, but I'll try it again.

adam

Quoted 4 lines

Regards,

Tony

author
#8 lore raw
Quoted 44 lines · Adam Ford
Quoted 13 lines · Tony Lindgren
Quoted 2 lines · Pali Rohár
Quoted 1 line · On Monday 09 September 2019 08:37:09 Adam Ford wrote:

I applied this on 5.3 and it is working. I assume the same is true in for-next.

Hmm I noticed I stopped getting RNG data after several rmmod modprobe cycles, or several hd /dev/random reads. Anybody else seeing that?

Quoted 5 lines
Quoted 4 lines

Do you want to submit a formal patch? I can mark it as 'tested-by' This really helps speed up the startup sequence on boards with sshd because it delays for nearly 80 seconds waiting for entropy without the hwrng.

Quoted 6 lines
Quoted 4 lines

Hi! When applying a patch, could you please disable this rng for n900?

In omap3-n900.dts for rng should be status = "disabled" (as Tony already wrote), similarly like for aes.

Yeah I'll post a proper patch after -rc1.

FYI,

By putting your node into omap34xx.dtsi and omap36xx.dtsi along with the following, I can get the RNG to work on an OMAP3530 and a DM3730.

arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi +1 -1
index 5e9d1afcd422..73f351e6d132 100644
@@ -259,7 +259,7 @@
                         <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
                         <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
                         <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, <&icr_ick>,
-                        <&des2_ick>, <&mspro_ick>, <&mailboxes_ick>,
+                        <&des2_ick>, <&mspro_ick>, <&mailboxes_ick>,
 <&rng_ick>,
                         <&mspro_fck>;
        };

};

Quoted 7 lines

I tried doing the same for am3517, but it doesn't appear to work. In fact, the board hangs at boot with no splat, so I assume that some clock isn't running and causing a hang. Figure 4-50 in the AM3517 TRM shows the security_l4_iclk2, so I wonder if the HW mods for AES, SHA, etc are doing something to enable this clock. Those HWmods are disabled on AM3517. I tried turning on the hwmods for them before without success, but I'll try it again.

According to a note in omap_hwmod_3xxx_data.c,

/*
* Apparently the SHA/MD5 and AES accelerator IP blocks are
* only present on some AM35xx chips, and no one knows which
* ones. See
* http://www.spinics.net/lists/arm-kernel/msg215466.html So
* if you need these IP blocks on an AM35xx, try uncommenting
* the following lines.
*/

I decided to uncomment the hwmod entries, and I got the following:

[    0.263222] omap_hwmod: sham: _wait_target_ready failed: -16
[    0.263248] omap_hwmod: sham: cannot be enabled for reset (3)
[    0.265837] omap_hwmod: aes: _wait_target_ready failed: -16
[    0.265851] omap_hwmod: aes: cannot be enabled for reset (3)
[    6.208866] omap_hwmod: sham: _wait_target_ready failed: -16
[    6.287732] omap_hwmod: aes: _wait_target_ready failed: -16

Based on this, I wonder if the sham and aes modules are not present. If this is the case, it might explain why I cannot use the rng either.

adam

Quoted 6 lines

adam

Quoted 4 lines

Regards,

Tony

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#9 lore raw
Quoted 11 lines · On Tuesday 10 September 2019 11:21:34 Adam Ford wrote:

According to a note in omap_hwmod_3xxx_data.c,

/*
* Apparently the SHA/MD5 and AES accelerator IP blocks are
* only present on some AM35xx chips, and no one knows which
* ones. See
* http://www.spinics.net/lists/arm-kernel/msg215466.html So
* if you need these IP blocks on an AM35xx, try uncommenting
* the following lines.
*/

Quoted 8 lines

I decided to uncomment the hwmod entries, and I got the following:

[    0.263222] omap_hwmod: sham: _wait_target_ready failed: -16
[    0.263248] omap_hwmod: sham: cannot be enabled for reset (3)
[    0.265837] omap_hwmod: aes: _wait_target_ready failed: -16
[    0.265851] omap_hwmod: aes: cannot be enabled for reset (3)
[    6.208866] omap_hwmod: sham: _wait_target_ready failed: -16
[    6.287732] omap_hwmod: aes: _wait_target_ready failed: -16

Hi! Same errors I got in qemu-n900, but not on real N900. So I guess those errors means that IP blocks are not present.

Quoted 2 lines

Based on this, I wonder if the sham and aes modules are not present. If this is the case, it might explain why I cannot use the rng either.

Probably this is the reason, you do not have crypto/rng HW engine.

Signature · 2 lines
Pali Rohár
[email protected]
author
#10 lore raw
In reply to Tony Lindgren
Quoted 13 lines · Tony Lindgren
Quoted 2 lines · Pali Rohár
Quoted 1 line · On Monday 09 September 2019 08:37:09 Adam Ford wrote:

I applied this on 5.3 and it is working. I assume the same is true in for-next.

Hmm I noticed I stopped getting RNG data after several rmmod modprobe cycles, or several hd /dev/random reads. Anybody else seeing that?

Quoted 5 lines
Quoted 4 lines

Do you want to submit a formal patch? I can mark it as 'tested-by' This really helps speed up the startup sequence on boards with sshd because it delays for nearly 80 seconds waiting for entropy without the hwrng.

Quoted 6 lines
Quoted 4 lines

Hi! When applying a patch, could you please disable this rng for n900?

In omap3-n900.dts for rng should be status = "disabled" (as Tony already wrote), similarly like for aes.

Yeah I'll post a proper patch after -rc1.

Tony,

I am just following up on this. Without the HWRNG there are some tools and daemons like sshd which wait a long time at startup. The patch you sent really helps speed up the startup time in these cases. At least in my case, it shaves 80 seconds off by eliminating the delays.

Do you think you'll have time to post a more formal patch? If not, I can do it. I just don't know which mailing list is the more appropriate. I was able to verity your patch on a DM3730 and OMAP3530

Thanks,

adam

Quoted 4 lines

Regards,

Tony

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

maintainer
#11 lore raw
Quoted 29 lines · Adam Ford
Quoted 13 lines · Tony Lindgren
Quoted 2 lines · Pali Rohár
Quoted 1 line · On Monday 09 September 2019 08:37:09 Adam Ford wrote:

I applied this on 5.3 and it is working. I assume the same is true in for-next.

Hmm I noticed I stopped getting RNG data after several rmmod modprobe cycles, or several hd /dev/random reads. Anybody else seeing that?

Quoted 5 lines
Quoted 4 lines

Do you want to submit a formal patch? I can mark it as 'tested-by' This really helps speed up the startup sequence on boards with sshd because it delays for nearly 80 seconds waiting for entropy without the hwrng.

Quoted 6 lines
Quoted 4 lines

Hi! When applying a patch, could you please disable this rng for n900?

In omap3-n900.dts for rng should be status = "disabled" (as Tony already wrote), similarly like for aes.

Yeah I'll post a proper patch after -rc1.

Tony,

I am just following up on this. Without the HWRNG there are some tools and daemons like sshd which wait a long time at startup. The patch you sent really helps speed up the startup time in these cases. At least in my case, it shaves 80 seconds off by eliminating the delays.

Quoted 3 lines

Do you think you'll have time to post a more formal patch? If not, I can do it. I just don't know which mailing list is the more appropriate. I was able to verity your patch on a DM3730 and OMAP3530

Yeah sorry for the delays, I'll post it when I get a chance to work on that again. I need to first deal with the other pending patches for v5.5, and we've had quite a few fixes for v5.4.

Regards,

Tony

author
#12 lore raw
In reply to Tony Lindgren
Quoted 16 lines · Tony Lindgren

Hi,

Quoted 11 lines · Adam Ford

The datasheet for the AM3517 shows the RNG is connected to L4. It shows the module address for the RNG is 0x480A0000, and it matches the omap2.dtsi description. Since the driver can support omap2 and omap4, it seems reasonable to assume the omap3 would use the same core for the RNG.

This RFC, mimics much of the omap2 hwmods on the OMAP3. It also adds the necessary clock for driving the RNG. Unfortunately, it appears non-functional. If anyone has any suggestions on how to finish the hwmod (or port it to the newer l4 device tree format), feedback is requested.

Quoted 8 lines

Yup I'll take the bait :) The patch below seems to do the trick for me on dm3730 based on translating your patch to probe with ti-sysc.

Not sure about 34xx, it seems we're missing rng_clk? Care to give it a try and attempt simlar patches for 34xx and 3517?

I took the block you added to omap36xx and copied it to omap34xx. Since this is present in the omap2.dtsi, I wonder if it could be used at the omap3.dtsi level instead of am3517, omap34xx and omap36xx. What is not clear to me is the clocking architecture needed. The omap34xx-omap36xx-clocks.dtsi have the aes1, rng_ick, sha1, and des1 setup which appears to be present in the am3517 based on that datasheet, but they are all dependent on the security_l4_ick2 which is not defined for am35. I wonder if all these could move to omap3 and its respective clock file. Duplicating it in 3x locations doesn't seem to make sense, but I don't have every permutation of omap3 to know, and those features are not clearly documented.

I have it working on an omap3530:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.3.0-rc8-00009-gaa2f12f5625a-dirty
(aford@aford-OptiPlex-7050) (gcc version 8.3.0 (Buildroot
2019.02.4-00056-gb0868303cf)) #11 SMP Mon Sep 9 13:59:31 CDT 2019
[    0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT
nonaliasing instruction cache
[    0.000000] OF: fdt: Machine model: LogicPD Zoom OMAP35xx SOM-LV

Development Kit
...snip...

[    0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp)

... snip...

[    0.000000] random: get_random_bytes called from
start_kernel+0x2e8/0x514 with crng_init=0
[    2.573120] random: fast init done
[    5.172821] random: udevd: uninitialized urandom read (16 bytes read)
[    5.182922] random: udevd: uninitialized urandom read (16 bytes read)
[    5.190460] random: udevd: uninitialized urandom read (16 bytes read)
[    7.739837] omap_rng 480a0000.rng: Random Number Generator ver. 70
[    7.747283] random: crng init done
[    7.750793] random: 1 urandom warning(s) missed due to ratelimiting

And hexdump is working on both /dev/hwrng and /dev/random I have not been able to replicate the issue you mentioned about it dying after a few reads and/or rmmod-modprobe cycles.

Quoted 3 lines

At least I'm not needing the "ti,no-reset-on-init" property that your patch has a comment for. Maybe that's needed on some other omap3.

The hwmod I used was a copy-paste from omap2, so it might not be needed in omap3's at all.

Quoted 3 lines

Oh and this needs to default to status = "disabled" for HS devices like n900 as it needs to use the omap3-rom-rng.

I don't know enough about the HS version of the OMAP3, but what's the main difference between omap3-rom-rng and this one?

adam

Quoted 39 lines

Regards,

Tony

8< -----------------------

arch/arm/boot/dts/omap36xx.dtsi +23 -0
@@ -140,6 +140,29 @@
                        };
                };
 
+               rng_target: target-module@480a0000 {
+                       compatible = "ti,sysc-omap2", "ti,sysc";
+                       reg = <0x480a003c 0x4>,
+                             <0x480a0040 0x4>,
+                             <0x480a0044 0x4>;
+                       reg-names = "rev", "sysc", "syss";
+                       ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
+                       ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+                                       <SYSC_IDLE_NO>;
+                       ti,syss-mask = <1>;
+                       clocks = <&rng_ick>;
+                       clock-names = "ick";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+                       ranges = <0 0x480a0000 0x2000>;
+
+                       rng: rng@0 {
+                               compatible = "ti,omap2-rng";
+                               reg = <0x0 0x2000>;
+                               interrupts = <52>;
+                       };
+               };
+
                /*
                 * Note that the sysconfig register layout is a subset of the
                 * "ti,sysc-omap4" type register with just sidle and midle bits
#13 lore raw

Hi,

Quoted 6 lines · Adam Ford
Quoted 2 lines · Tony Lindgren

Oh and this needs to default to status = "disabled" for HS devices like n900 as it needs to use the omap3-rom-rng.

I don't know enough about the HS version of the OMAP3, but what's the main difference between omap3-rom-rng and this one?

The OMAP HS chips have the bus firewall configured to block direct access to some cryptography related devices. The kernel will crash with a bus error, if you try to read/write the registers for protected devices. The omap3-rom-rng avoids this by communicating with the security middleware component instead of directly accessing the RNG hardware.

-- Sebastian

#14 lore raw
Quoted 7 lines · On Tuesday 10 September 2019 15:37:32 Sebastian Reichel wrote:

Hi,

Quoted 4 lines · Adam Ford
Quoted 2 lines · Tony Lindgren

Oh and this needs to default to status = "disabled" for HS devices like n900 as it needs to use the omap3-rom-rng.

Quoted 7 lines
Quoted 2 lines

I don't know enough about the HS version of the OMAP3, but what's the main difference between omap3-rom-rng and this one?

The OMAP HS chips have the bus firewall configured to block direct access to some cryptography related devices. The kernel will crash with a bus error, if you try to read/write the registers for protected devices.

And if you try to read it more times, SOC would be rebooted for security reasons.

Quoted 3 lines

The omap3-rom-rng avoids this by communicating
with the security middleware component instead of directly accessing the RNG hardware.

And that component is loaded by signed bootloader into "secure" area not accessible by "non-secure" work (like kernel) and communication is done via arm smc instruction.

Signature · 2 lines
Pali Rohár
[email protected]