Skip to contentSkip to conversation

net: stmmac: Add support for MDIO interrupts

PATCH Superseded Voon Weifeng 2 participants 5 messages Sep 4, 2019 – Sep 5, 2019

Subsystems (4)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 net: stmmac: Add support for MDIO interrupts

From: "Chuah, Kim Tatt" <[email protected]>

DW EQoS v5.xx controllers added capability for interrupt generation when MDIO interface is done (GMII Busy bit is cleared). This patch adds support for this interrupt on supported HW to avoid polling on GMII Busy bit.

stmmac_mdio_read() & stmmac_mdio_write() will sleep until wake_up() is called by the interrupt handler.

drivers/net/ethernet/stmicro/stmmac/common.h +2 -0
index 49aa56ca09cc..775a1c114b1a 100644
@@ -448,6 +448,8 @@ struct mac_device_info {
 	unsigned int pcs;
 	unsigned int pmt;
 	unsigned int ps;
+	bool mdio_intr_en;
+	wait_queue_head_t mdio_busy_wait;
 };
 
 struct stmmac_rx_routing {
drivers/net/ethernet/stmicro/stmmac/dwmac4.h +1 -0
index 2ed11a581d80..1be6a8a88b8f 100644
@@ -106,6 +106,7 @@ enum dwmac4_irq_status {
 	mmc_irq = 0x00000100,
 	lpi_irq = 0x00000020,
 	pmt_irq = 0x00000010,
+	mdio_irq = 0x00040000,
 };
 
 /* MAC PMT bitmap */
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +7 -0
index fc9954e4a772..97fca6d65141 100644
@@ -59,6 +59,9 @@ static void dwmac4_core_init(struct mac_device_info *hw,
 	if (hw->pcs)
 		value |= GMAC_PCS_IRQ_DEFAULT;
 
+	if (hw->mdio_intr_en)
+		value |= GMAC_INT_MDIO_EN;
+
 	writel(value, ioaddr + GMAC_INT_EN);
 }
 
@@ -629,6 +632,9 @@ static int dwmac4_irq_status(struct mac_device_info *hw,
 			x->irq_rx_path_exit_lpi_mode_n++;
 	}
 
+	if (intr_status & mdio_irq)
+		wake_up(&hw->mdio_busy_wait);
+
 	dwmac_pcs_isr(ioaddr, GMAC_PCS_BASE, intr_status, x);
 	if (intr_status & PCS_RGSMIIIS_IRQ)
 		dwmac4_phystatus(ioaddr, x);
@@ -836,6 +842,7 @@ static void dwmac4_set_mac_loopback(void __iomem *ioaddr, bool enable)
 	.rxp_config = dwmac5_rxp_config,
 	.flex_pps_config = dwmac5_flex_pps_config,
 	.set_mac_loopback = dwmac4_set_mac_loopback,
+	.mdio_intr_dis = dwmac5_mdio_intr_dis,
 };
 
 int dwmac4_setup(struct stmmac_priv *priv)
drivers/net/ethernet/stmicro/stmmac/dwmac5.c +8 -0
index 3f4f3132e16b..c58751e1dcb6 100644
@@ -549,3 +549,11 @@ int dwmac5_flex_pps_config(void __iomem *ioaddr, int index,
 	writel(val, ioaddr + MAC_PPS_CONTROL);
 	return 0;
 }
+
+void dwmac5_mdio_intr_dis(void __iomem *ioaddr)
+{
+	u32 val = readl(ioaddr + GMAC_INT_EN);
+
+	val &= ~GMAC_INT_MDIO_EN;
+	writel(val, ioaddr + GMAC_INT_EN);
+}
drivers/net/ethernet/stmicro/stmmac/dwmac5.h +4 -0
index 775db776b3cc..a56511a4c97d 100644
@@ -72,6 +72,9 @@
 #define TCEIE				BIT(0)
 #define DMA_ECC_INT_STATUS		0x00001088
 
+/* MDIO interrupt enable in MAC_Interrupt_Enable register */
+#define GMAC_INT_MDIO_EN		BIT(18)
+
 int dwmac5_safety_feat_config(void __iomem *ioaddr, unsigned int asp);
 int dwmac5_safety_feat_irq_status(struct net_device *ndev,
 		void __iomem *ioaddr, unsigned int asp,
@@ -83,5 +86,6 @@ int dwmac5_rxp_config(void __iomem *ioaddr, struct stmmac_tc_entry *entries,
 int dwmac5_flex_pps_config(void __iomem *ioaddr, int index,
 			   struct stmmac_pps_cfg *cfg, bool enable,
 			   u32 sub_second_inc, u32 systime_flags);
+void dwmac5_mdio_intr_dis(void __iomem *ioaddr);
 
 #endif /* __DWMAC5_H__ */
drivers/net/ethernet/stmicro/stmmac/hwif.c +9 -0
index 3af2e5015245..7127efe652db 100644
@@ -73,6 +73,7 @@ static int stmmac_dwmac4_quirks(struct stmmac_priv *priv)
 	bool gmac;
 	bool gmac4;
 	bool xgmac;
+	bool mdio_intr_en;
 	u32 min_id;
 	const struct stmmac_regs_off regs;
 	const void *desc;
@@ -90,6 +91,7 @@ static int stmmac_dwmac4_quirks(struct stmmac_priv *priv)
 		.gmac = false,
 		.gmac4 = false,
 		.xgmac = false,
+		.mdio_intr_en = false,
 		.min_id = 0,
 		.regs = {
 			.ptp_off = PTP_GMAC3_X_OFFSET,
@@ -108,6 +110,7 @@ static int stmmac_dwmac4_quirks(struct stmmac_priv *priv)
 		.gmac = true,
 		.gmac4 = false,
 		.xgmac = false,
+		.mdio_intr_en = false,
 		.min_id = 0,
 		.regs = {
 			.ptp_off = PTP_GMAC3_X_OFFSET,
@@ -126,6 +129,7 @@ static int stmmac_dwmac4_quirks(struct stmmac_priv *priv)
 		.gmac = false,
 		.gmac4 = true,
 		.xgmac = false,
+		.mdio_intr_en = false,
 		.min_id = 0,
 		.regs = {
 			.ptp_off = PTP_GMAC4_OFFSET,
@@ -144,6 +148,7 @@ static int stmmac_dwmac4_quirks(struct stmmac_priv *priv)
 		.gmac = false,
 		.gmac4 = true,
 		.xgmac = false,
+		.mdio_intr_en = false,
 		.min_id = DWMAC_CORE_4_00,
 		.regs = {
 			.ptp_off = PTP_GMAC4_OFFSET,
@@ -162,6 +167,7 @@ static int stmmac_dwmac4_quirks(struct stmmac_priv *priv)
 		.gmac = false,
 		.gmac4 = true,
 		.xgmac = false,
+		.mdio_intr_en = false,
 		.min_id = DWMAC_CORE_4_10,
 		.regs = {
 			.ptp_off = PTP_GMAC4_OFFSET,
@@ -180,6 +186,7 @@ static int stmmac_dwmac4_quirks(struct stmmac_priv *priv)
 		.gmac = false,
 		.gmac4 = true,
 		.xgmac = false,
+		.mdio_intr_en = true,
 		.min_id = DWMAC_CORE_5_10,
 		.regs = {
 			.ptp_off = PTP_GMAC4_OFFSET,
@@ -198,6 +205,7 @@ static int stmmac_dwmac4_quirks(struct stmmac_priv *priv)
 		.gmac = false,
 		.gmac4 = false,
 		.xgmac = true,
+		.mdio_intr_en = false,
 		.min_id = DWXGMAC_CORE_2_10,
 		.regs = {
 			.ptp_off = PTP_XGMAC_OFFSET,
@@ -276,6 +284,7 @@ int stmmac_hwif_init(struct stmmac_priv *priv)
 		mac->mode = mac->mode ? : entry->mode;
 		mac->tc = mac->tc ? : entry->tc;
 		mac->mmc = mac->mmc ? : entry->mmc;
+		mac->mdio_intr_en = mac->mdio_intr_en ? : entry->mdio_intr_en;
 
 		priv->hw = mac;
 		priv->ptpaddr = priv->ioaddr + entry->regs.ptp_off;
drivers/net/ethernet/stmicro/stmmac/hwif.h +4 -0
index 9435b312495d..d42885426e78 100644
@@ -363,6 +363,8 @@ struct stmmac_ops {
 	int (*get_mac_tx_timestamp)(struct mac_device_info *hw, u64 *ts);
 	/* Source Address Insertion / Replacement */
 	void (*sarc_configure)(void __iomem *ioaddr, int val);
+	/* Disable mdio interrupt */
+	void (*mdio_intr_dis)(void __iomem *ioaddr);
 };
 
 #define stmmac_core_init(__priv, __args...) \
@@ -443,6 +445,8 @@ struct stmmac_ops {
 	stmmac_do_callback(__priv, mac, get_mac_tx_timestamp, __args)
 #define stmmac_sarc_configure(__priv, __args...) \
 	stmmac_do_void_callback(__priv, mac, sarc_configure, __args)
+#define stmmac_mdio_intr_dis(__priv, __args...) \
+	stmmac_do_void_callback(__priv, mac, mdio_intr_dis, __args)
 
 /* PTP and HW Timer helpers */
 struct stmmac_hwtimestamp {
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +5 -0
index 06ccd216ae90..2557a2beb03d 100644
@@ -2768,6 +2768,8 @@ static int stmmac_release(struct net_device *dev)
 	phylink_stop(priv->phylink);
 	phylink_disconnect_phy(priv->phylink);
 
+	stmmac_mdio_intr_dis(priv, priv->ioaddr);
+
 	stmmac_stop_all_queues(priv);
 
 	stmmac_disable_all_queues(priv);
@@ -4463,6 +4465,9 @@ int stmmac_dvr_probe(struct device *device,
 	if (ret)
 		goto error_hw_init;
 
+	/* mdio intr wait queue */
+	init_waitqueue_head(&priv->hw->mdio_busy_wait);
+
 	stmmac_check_ether_addr(priv);
 
 	/* Configure real RX and TX queues */
drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c +49 -8

112 lines not on this page · raw message

Signature · 6 lines
Changelog v2
*mdio interrupt mode or polling mode will depends on mdio interrupt enable bit
*Disable the mdio interrupt enable bit in stmmac_release
*Remove the condition for initialize wait queues
*Applied reverse Christmas tree
1.9.1
#1 lore raw
Quoted 10 lines · Voon Weifeng

From: "Chuah, Kim Tatt" <[email protected]>

DW EQoS v5.xx controllers added capability for interrupt generation when MDIO interface is done (GMII Busy bit is cleared). This patch adds support for this interrupt on supported HW to avoid polling on GMII Busy bit.

stmmac_mdio_read() & stmmac_mdio_write() will sleep until wake_up() is called by the interrupt handler.

Quoted 6 lines

Hi Voon

It is normal to include a short description of what you changed between the previous version and this version.

The formatting of this patch also looks a bit odd. Did you use git format-patch ; git send-email?

Thanks
Andrew

#2 lore raw
Quoted 18 lines · Voon Weifeng
Quoted 10 lines

From: "Chuah, Kim Tatt" <[email protected]>

DW EQoS v5.xx controllers added capability for interrupt generation when MDIO interface is done (GMII Busy bit is cleared). This patch adds support for this interrupt on supported HW to avoid polling on GMII Busy bit.

stmmac_mdio_read() & stmmac_mdio_write() will sleep until wake_up() is called by the interrupt handler.

Quoted 6 lines
Quoted 4 lines

Hi Voon

It is normal to include a short description of what you changed between the previous version and this version.

The change log is near the end of the patch:
/**
--
Changelog v2
*mdio interrupt mode or polling mode will depends on mdio interrupt enable bit *Disable the mdio interrupt enable bit in stmmac_release
*Remove the condition for initialize wait queues
*Applied reverse Christmas tree
1.9.1

Quoted 3 lines

The formatting of this patch also looks a bit odd. Did you use git format-patch ; git send-email?

Yes, I do git format-patch, then ./scripts/checkpatch.pl. Lastly git send-email

Quoted 3 lines

Thanks
Andrew

#3 lore raw
Quoted 10 lines

The change log is near the end of the patch:
/**
--
Changelog v2
*mdio interrupt mode or polling mode will depends on mdio interrupt enable bit *Disable the mdio interrupt enable bit in stmmac_release
*Remove the condition for initialize wait queues
*Applied reverse Christmas tree
1.9.1

At the end, nobody sees it, because everybody else does it at the beginning.

https://www.kernel.org/doc/html/latest/process/submitting-patches.html?highlight=submitting#the-canonical-patch-format

This talks about the ---. David prefers to see the change log before the ---. Other maintainers want it after the ---.

Quoted 7 lines
Quoted 4 lines

The formatting of this patch also looks a bit odd. Did you use git format-patch ; git send-email?

Yes, I do git format-patch, then ./scripts/checkpatch.pl. Lastly git send-email

What looked odd is the missing --- marker. git format-patch should of create that as part of the patch.

Andrew

#4 lore raw
Quoted 24 lines
Quoted 9 lines

The change log is near the end of the patch:
/**
--
Changelog v2
*mdio interrupt mode or polling mode will depends on mdio interrupt enable bit *Disable the mdio interrupt enable bit in stmmac_release *Remove the condition for initialize wait queues *Applied reverse Christmas tree
1.9.1

At the end, nobody sees it, because everybody else does it at the beginning.

https://www.kernel.org/doc/html/latest/process/submitting-
patches.html?highlight=submitting#the-canonical-patch-format

This talks about the ---. David prefers to see the change log before the ---. Other maintainers want it after the ---.

Quoted 5 lines
Quoted 4 lines

The formatting of this patch also looks a bit odd. Did you use git format-patch ; git send-email?

Quoted 7 lines
Quoted 2 lines

Yes, I do git format-patch, then ./scripts/checkpatch.pl. Lastly git send-email

What looked odd is the missing --- marker. git format-patch should of create that as part of the patch.

Andrew

I found out why as I did a git format-patch with -p which is without the Stat. I will resent v3 to using correct format.

Weifeng