OMAP3: convert opp-v1 to opp-v2 and read speed binned / 720MHz grade bits
Subsystems (2)
cover OMAP3: convert opp-v1 to opp-v2 and read speed binned / 720MHz grade bits
Changes PATCH V1:
* fix typo in omap3-ldp.dts
(reported by Tony Lindgren <[email protected]>)
* extend commit message to describe the bit patterns needed for opp-supported-hw
* add error check to ioremap()
(suggested by Christ van Willegen <[email protected]>)
* update Documentation/devicetree/bindings/arm/omap/omap.txt
* change bulk update to use "ti,omap3430" and "ti,omap3630"
* update OPP4 of omap3430 to 1275 mV since it was not a valid voltage for the twl4030 driver (reported by Tony Lindgren <[email protected]>)
RFC V2 2019-09-04 10:53:43:
* merge separate patch to remove opp-v1 table from n950-n9 into the general omap3xxx.dtsi patch
(suggested by Viresh Kumar <[email protected]>)
* add legacy compatibility to ti,omap3430 and ti,omap3630 for the ti-cpufreq driver
* make driver and omap3xxx.dtsi patches pass checkpatch
* add bulk patch to explicitly define compatibility to ti,omap3430 and ti,omap36xx in addition to ti,omap3 of all in-tree boards where it was missing
RFC V1 2019-09-02 12:55:55:
This patch set converts the omap3 opp tables to opp-v2 format and extends the ti-cpufreq to support omap3.
It adds 720 MHz (omap34xx) and 1 GHz (omap36xx) OPPs but tells the ti-cpufreq driver to disable them if the speed binned / 720MHz grade eFuse bits indicate that the chip is not rated for that speed.
It has been tested (for chip variant detection, not reliability of the high speed OPPs) on:
* BeagleBoard C2 (omap3530 600MHz)
* BeagleBoard XM B (dm3730 800MHz)
* GTA04A4 (dm3730 800MHz)
* GTA04A5 (dm3730 1GHz)
H. Nikolaus Schaller (4):
cpufreq: ti-cpufreq: add support for omap34xx and omap36xx
ARM: dts: replace opp-v1 tables by opp-v2 for omap34xx and omap36xx
ARM: dts: omap3: bulk convert compatible to be explicitly ti,omap3430
or ti,omap3630 or ti,am3517
DTS: bindings: omap: update bindings documentation
.../devicetree/bindings/arm/omap/omap.txt | 30 +++--- arch/arm/boot/dts/am3517_mt_ventoux.dts | 2 +- .../boot/dts/logicpd-som-lv-35xx-devkit.dts | 2 +- .../boot/dts/logicpd-torpedo-35xx-devkit.dts | 2 +- arch/arm/boot/dts/omap3-beagle-xm.dts | 2 +- arch/arm/boot/dts/omap3-beagle.dts | 2 +- arch/arm/boot/dts/omap3-cm-t3530.dts | 2 +- arch/arm/boot/dts/omap3-cm-t3730.dts | 2 +- arch/arm/boot/dts/omap3-devkit8000-lcd43.dts | 2 +- arch/arm/boot/dts/omap3-devkit8000-lcd70.dts | 2 +- arch/arm/boot/dts/omap3-devkit8000.dts | 2 +- arch/arm/boot/dts/omap3-gta04.dtsi | 2 +- arch/arm/boot/dts/omap3-ha-lcd.dts | 2 +- arch/arm/boot/dts/omap3-ha.dts | 2 +- arch/arm/boot/dts/omap3-igep0020-rev-f.dts | 2 +- arch/arm/boot/dts/omap3-igep0020.dts | 2 +- arch/arm/boot/dts/omap3-igep0030-rev-g.dts | 2 +- arch/arm/boot/dts/omap3-igep0030.dts | 2 +- arch/arm/boot/dts/omap3-ldp.dts | 2 +- arch/arm/boot/dts/omap3-lilly-a83x.dtsi | 2 +- arch/arm/boot/dts/omap3-lilly-dbb056.dts | 2 +- arch/arm/boot/dts/omap3-n9.dts | 2 +- arch/arm/boot/dts/omap3-n950-n9.dtsi | 7 -- arch/arm/boot/dts/omap3-n950.dts | 2 +- .../arm/boot/dts/omap3-overo-storm-alto35.dts | 2 +- .../boot/dts/omap3-overo-storm-chestnut43.dts | 2 +- .../boot/dts/omap3-overo-storm-gallop43.dts | 2 +- .../arm/boot/dts/omap3-overo-storm-palo35.dts | 2 +- .../arm/boot/dts/omap3-overo-storm-palo43.dts | 2 +- .../arm/boot/dts/omap3-overo-storm-summit.dts | 2 +- arch/arm/boot/dts/omap3-overo-storm-tobi.dts | 2 +- .../boot/dts/omap3-overo-storm-tobiduo.dts | 2 +- arch/arm/boot/dts/omap3-pandora-1ghz.dts | 2 +- arch/arm/boot/dts/omap3-sbc-t3530.dts | 2 +- arch/arm/boot/dts/omap3-sbc-t3730.dts | 2 +- arch/arm/boot/dts/omap3-sniper.dts | 2 +- arch/arm/boot/dts/omap3-thunder.dts | 2 +- arch/arm/boot/dts/omap3-zoom3.dts | 2 +- arch/arm/boot/dts/omap3430-sdp.dts | 2 +- arch/arm/boot/dts/omap34xx.dtsi | 65 +++++++++++-- arch/arm/boot/dts/omap36xx.dtsi | 53 +++++++++-- drivers/cpufreq/cpufreq-dt-platdev.c | 2 +- drivers/cpufreq/ti-cpufreq.c | 91 ++++++++++++++++++- 43 files changed, 245 insertions(+), 77 deletions(-)
Signature · 1 line
2.19.1
PATCH 1/4 cpufreq: ti-cpufreq: add support for omap34xx and omap36xx
This adds code and tables to read the silicon revision and eFuse (speed binned / 720 MHz grade) bits for selecting opp-v2 table entries.
Since these bits are not always part of the syscon register range (like for am33xx, am43, dra7), we add code to directly read the register values using ioremap() if syscon access fails.
The format of the opp-supported-hw entries is that it has two 32 bit bitfields. E.g.:
opp-supported-hw = <0xffffffff 3>
The first value is matched against the bit position of the silicon revision which is (see TRM)
omap34xx:
BIT(0) ES1.0
BIT(1) ES2.0
BIT(2) ES2.1
BIT(3) ES3.0
BIT(4) ES3.1
BIT(7) ES3.1.2
omap36xx:
BIT(0) ES1.0
BIT(1) ES1.1
BIT(2) ES1.2
The second value is matched against the speed grade eFuse:
BIT(0) no high speed OPP
BIT(1) high speed OPP
This means for the example above that it is always enabled while e.g.
opp-supported-hw = <0x1 2>
enables the OPP only for ES1.0 BIT(0) and if the high speed eFuse is set BIT(1).
--- drivers/cpufreq/ti-cpufreq.c | 91 +++++++++++++++++++++++++++++++++++- 1 file changed, 89 insertions(+), 2 deletions(-)
drivers/cpufreq/ti-cpufreq.c +89 -2
@@ -31,6 +31,11 @@#define DRA7_EFUSE_OD_MPU_OPP BIT(1)#define DRA7_EFUSE_HIGH_MPU_OPP BIT(2) +#define OMAP3_CONTROL_DEVICE_STATUS 0x4800244C +#define OMAP3_CONTROL_IDCODE 0x4830A204 +#define OMAP34xx_ProdID_SKUID 0x4830A20C +#define OMAP3_SYSCON_BASE (0x48000000 + 0x2000 + 0x270) +#define VERSION_COUNT 2struct ti_cpufreq_data ;
@@ -84,6 +89,13 @@ static unsigned long dra7_efuse_xlate(struct ti_cpufreq_data *opp_data,return calculated_efuse; } +static unsigned long omap3_efuse_xlate (struct ti_cpufreq_data *opp_data, +unsigned long efuse) +{ +/* OPP enable bit ("Speed Binned") */ +return BIT (efuse); +} +static struct ti_cpufreq_soc_data am3x_soc_data = { .efuse_xlate = amx3_efuse_xlate, .efuse_fallback =AM33XX_800M_ARM_MPU_MAX_FREQ ,
@@ -111,6 +123,56 @@ static struct ti_cpufreq_soc_data dra7_soc_data = { .multi_regulator = true, }; +/* +* OMAP35x TRM (SPRUF98K): +* CONTROL_IDCODE (0x4830 A204) describes Silicon revisions. +* Control OMAP Status Register 15:0 (Address 0x4800 244C) +* to separate between omap3503, omap3515, omap3525, omap3530 +* and feature presence. +* There are encodings for versions limited to 400/266MHz +* but we ignore. +* Not clear if this also holds for omap34xx. +* some eFuse values e.g. CONTROL_FUSE_OPP1_VDD1 +* are stored in the SYSCON register range +* Register 0x4830A20C [ProdID.SKUID] [0:3] +* 0x0 for normal 600/430MHz device. +* 0x8 for 720/520MHz device. +* Not clear what omap34xx value is. +*/ + +static struct ti_cpufreq_soc_data omap34xx_soc_data = { + .efuse_xlate = omap3_efuse_xlate, + .efuse_offset = OMAP34xx_ProdID_SKUID -OMAP3_SYSCON_BASE , + .efuse_shift =3 , + .efuse_mask =BIT (3 ), + .rev_offset =OMAP3_CONTROL_IDCODE -OMAP3_SYSCON_BASE , + .multi_regulator = false, +}; + +/* +* AM/DM37x TRM (SPRUGN4M) +* CONTROL_IDCODE (0x4830 A204) describes Silicon revisions. +* Control Device Status Register 15:0 (Address 0x4800 244C) +* to separate between am3703, am3715, dm3725, dm3730 +* and feature presence. +* Speed Binned = Bit 9 +* 0 800/600 MHz +* 1 1000/800 MHz +* some eFuse values e.g. CONTROL_FUSE_OPP 1G_VDD1 +* are stored in the SYSCON register range. +* There is no 0x4830A20C [ProdID.SKUID] register (exists but +* seems to always read as 0). +*/ + +static struct ti_cpufreq_soc_data omap36xx_soc_data = { + .efuse_xlate = omap3_efuse_xlate, + .efuse_offset =OMAP3_CONTROL_DEVICE_STATUS -OMAP3_SYSCON_BASE , + .efuse_shift =9 , + .efuse_mask =BIT (9 ), + .rev_offset =OMAP3_CONTROL_IDCODE -OMAP3_SYSCON_BASE , + .multi_regulator = false, +}; +/** * ti_cpufreq_get_efuse() - Parse and return efuse value present on SoC * @opp_data: pointer to ti_cpufreq_data context
@@ -127,7 +189,17 @@ static int ti_cpufreq_get_efuse(struct ti_cpufreq_data *opp_data, ret =regmap_read (opp_data->syscon, opp_data->soc_data->efuse_offset, &efuse); -if (ret) { +if (ret == -EIO ) { +/* not a syscon register! */ +void __iomem *regs =ioremap (OMAP3_SYSCON_BASE + + opp_data->soc_data->efuse_offset,4 ); + +if (!regs) +return -ENOMEM ; + efuse =readl (regs); +iounmap (regs); + } +else if (ret) {dev_err (dev,"Failed to read the efuse value from syscon: %d\n" , ret);
@@ -158,7 +230,17 @@ static int ti_cpufreq_get_rev(struct ti_cpufreq_data *opp_data, ret =regmap_read (opp_data->syscon, opp_data->soc_data->rev_offset, &revision); -if (ret) { +if (ret == -EIO ) { +/* not a syscon register! */ +void __iomem *regs =ioremap (OMAP3_SYSCON_BASE + + opp_data->soc_data->rev_offset,4 ); + +if (!regs) +return -ENOMEM ; + revision =readl (regs); +iounmap (regs); + } +else if (ret) {dev_err (dev,"Failed to read the revision number from syscon: %d\n" , ret);
@@ -190,6 +272,11 @@ static const struct of_device_id ti_cpufreq_of_match[] = { { .compatible = "ti,am33xx", .data = &am3x_soc_data, }, { .compatible = "ti,am43", .data = &am4x_soc_data, }, { .compatible = "ti,dra7", .data = &dra7_soc_data }, + { .compatible = "ti,omap34xx", .data = &omap34xx_soc_data, }, + { .compatible = "ti,omap36xx", .data = &omap36xx_soc_data, }, + /* legacy */ + { .compatible = "ti,omap3430", .data = &omap34xx_soc_data, }, + { .compatible = "ti,omap3630", .data = &omap36xx_soc_data, }, {}, };
Signature · 1 line
2.19.1
Re: [PATCH 1/4] cpufreq: ti-cpufreq: add support for omap34xx and omap36xx
Quoted 176 lines
Am 07.09.2019 um 08:56 schrieb H. Nikolaus Schaller <[email protected]>:
This adds code and tables to read the silicon revision and eFuse (speed binned / 720 MHz grade) bits for selecting opp-v2 table entries.
Since these bits are not always part of the syscon register range (like for am33xx, am43, dra7), we add code to directly read the register values using
ioremap()if syscon access fails.The format of the opp-supported-hw entries is that it has two 32 bit bitfields. E.g.:
opp-supported-hw = <0xffffffff 3>The first value is matched against the bit position of the silicon revision which is (see TRM)
omap34xx:
BIT(0) ES1.0
BIT(1) ES2.0
BIT(2) ES2.1
BIT(3) ES3.0
BIT(4) ES3.1
BIT(7) ES3.1.2omap36xx:
BIT(0) ES1.0
BIT(1) ES1.1
BIT(2) ES1.2The second value is matched against the speed grade eFuse:
BIT(0) no high speed OPP
BIT(1) high speed OPPThis means for the example above that it is always enabled while e.g.
opp-supported-hw = <0x1 2>enables the OPP only for ES1.0 BIT(0) and if the high speed eFuse is set BIT(1).
Signed-off-by H. Nikolaus Schaller <[email protected]>---
drivers/cpufreq/ti-cpufreq.c| 91 +++++++++++++++++++++++++++++++++++-1 file changed, 89 insertions(+), 2 deletions(-)drivers/cpufreq/ti-cpufreq.c +84
-2@@ -31,6 +31,11 @@#define DRA7_EFUSE_OD_MPU_OPP BIT(1)#define DRA7_EFUSE_HIGH_MPU_OPP BIT(2) +#define OMAP3_CONTROL_DEVICE_STATUS 0x4800244C +#define OMAP3_CONTROL_IDCODE 0x4830A204 +#define OMAP34xx_ProdID_SKUID 0x4830A20C +#define OMAP3_SYSCON_BASE (0x48000000 + 0x2000 + 0x270) +#define VERSION_COUNT 2struct ti_cpufreq_data ;@@ -84,6 +89,13 @@ static unsigned long dra7_efuse_xlate(struct ti_cpufreq_data *opp_data,return calculated_efuse; } +static unsigned long omap3_efuse_xlate (struct ti_cpufreq_data *opp_data, +unsigned long efuse) +{ +/* OPP enable bit ("Speed Binned") */ +return BIT (efuse); +} +static struct ti_cpufreq_soc_data am3x_soc_data = { .efuse_xlate = amx3_efuse_xlate, .efuse_fallback =AM33XX_800M_ARM_MPU_MAX_FREQ ,@@ -111,6 +123,56 @@ static struct ti_cpufreq_soc_data dra7_soc_data = { .multi_regulator = true, }; +/* +* OMAP35x TRM (SPRUF98K): +* CONTROL_IDCODE (0x4830 A204) describes Silicon revisions. +* Control OMAP Status Register 15:0 (Address 0x4800 244C) +* to separate between omap3503, omap3515, omap3525, omap3530 +* and feature presence. +* There are encodings for versions limited to 400/266MHz +* but we ignore. +* Not clear if this also holds for omap34xx. +* some eFuse values e.g. CONTROL_FUSE_OPP1_VDD1 +* are stored in the SYSCON register range +* Register 0x4830A20C [ProdID.SKUID] [0:3] +* 0x0 for normal 600/430MHz device. +* 0x8 for 720/520MHz device. +* Not clear what omap34xx value is. +*/ + +static struct ti_cpufreq_soc_data omap34xx_soc_data = { + .efuse_xlate = omap3_efuse_xlate, + .efuse_offset = OMAP34xx_ProdID_SKUID -OMAP3_SYSCON_BASE , + .efuse_shift =3 , + .efuse_mask =BIT (3 ), + .rev_offset =OMAP3_CONTROL_IDCODE -OMAP3_SYSCON_BASE , + .multi_regulator = false, +}; + +/* +* AM/DM37x TRM (SPRUGN4M) +* CONTROL_IDCODE (0x4830 A204) describes Silicon revisions. +* Control Device Status Register 15:0 (Address 0x4800 244C) +* to separate between am3703, am3715, dm3725, dm3730 +* and feature presence. +* Speed Binned = Bit 9 +* 0 800/600 MHz +* 1 1000/800 MHz +* some eFuse values e.g. CONTROL_FUSE_OPP 1G_VDD1 +* are stored in the SYSCON register range. +* There is no 0x4830A20C [ProdID.SKUID] register (exists but +* seems to always read as 0). +*/ + +static struct ti_cpufreq_soc_data omap36xx_soc_data = { + .efuse_xlate = omap3_efuse_xlate, + .efuse_offset =OMAP3_CONTROL_DEVICE_STATUS -OMAP3_SYSCON_BASE , + .efuse_shift =9 , + .efuse_mask =BIT (9 ), + .rev_offset =OMAP3_CONTROL_IDCODE -OMAP3_SYSCON_BASE , + .multi_regulator = false, +}; +/** * ti_cpufreq_get_efuse() - Parse and return efuse value present on SoC * @opp_data: pointer to ti_cpufreq_data context @@ -127,7 +189,17 @@ static int ti_cpufreq_get_efuse(struct ti_cpufreq_data *opp_data, ret =regmap_read (opp_data->syscon, opp_data->soc_data->efuse_offset, &efuse); -if (ret) { +if (ret == -EIO ) { +/* not a syscon register! */ +void __iomem *regs =ioremap (OMAP3_SYSCON_BASE + + opp_data->soc_data->efuse_offset,4 ); + +if (!regs) +return -ENOMEM ; + efuse =readl (regs); +iounmap (regs); + } +else if (ret) {dev_err (dev,"Failed to read the efuse value from syscon: %d\n" , ret);@@ -158,7 +230,17 @@ static int ti_cpufreq_get_rev(struct ti_cpufreq_data *opp_data, ret =regmap_read (opp_data->syscon, opp_data->soc_data->rev_offset, &revision); -if (ret) { +if (ret == -EIO ) { +/* not a syscon register! */ +void __iomem *regs =ioremap (OMAP3_SYSCON_BASE + + opp_data->soc_data->rev_offset,4 ); + +if (!regs) +return -ENOMEM ; + revision =readl (regs); +iounmap (regs); + } +else if (ret) {dev_err (dev,"Failed to read the revision number from syscon: %d\n" , ret);
drivers/cpufreq/ti-cpufreq.c static const struct of_device_id ti_cpufreq_of_match[] = { · line 279
Quoted 8 lines
drivers/cpufreq/ti-cpufreq.c +5
-0@@ -190,6 +272,11 @@ static const struct of_device_id ti_cpufreq_of_match[] = { { .compatible = "ti,am33xx", .data = &am3x_soc_data, }, { .compatible = "ti,am43", .data = &am4x_soc_data, }, { .compatible = "ti,dra7", .data = &dra7_soc_data }, + { .compatible = "ti,omap34xx", .data = &omap34xx_soc_data, }, + { .compatible = "ti,omap36xx", .data = &omap36xx_soc_data, }, + /* legacy */ + { .compatible = "ti,omap3430", .data = &omap34xx_soc_data, }, + { .compatible = "ti,omap3630", .data = &omap36xx_soc_data, },
Well, I just realized that with the latest DTS changes,
ti,omap34xx and ti,omap36xx are legacy and
ti,omap3430 and ti,omap3630 are now official.
Quoted 6 lines
drivers/cpufreq/ti-cpufreq.c +0
-0{}, };Signature · 1 line
2.19.1
Tony Lindgren
Reviewed-byRe: [PATCH 1/4] cpufreq: ti-cpufreq: add support for omap34xx and omap36xx
Quoted 13 lines · H. Nikolaus Schaller
drivers/cpufreq/ti-cpufreq.c static const struct of_device_id ti_cpufreq_of_match[] = { · line 279
Quoted 10 lines
Am 07.09.2019 um 08:56 schrieb H. Nikolaus Schaller <[email protected]>:
drivers/cpufreq/ti-cpufreq.c +5
-0@@ -190,6 +272,11 @@ static const struct of_device_id ti_cpufreq_of_match[] = { { .compatible = "ti,am33xx", .data = &am3x_soc_data, }, { .compatible = "ti,am43", .data = &am4x_soc_data, }, { .compatible = "ti,dra7", .data = &dra7_soc_data }, + { .compatible = "ti,omap34xx", .data = &omap34xx_soc_data, }, + { .compatible = "ti,omap36xx", .data = &omap36xx_soc_data, }, + /* legacy */ + { .compatible = "ti,omap3430", .data = &omap34xx_soc_data, }, + { .compatible = "ti,omap3630", .data = &omap36xx_soc_data, },Well, I just realized that with the latest DTS changes,
Quoted 2 lines
ti,omap34xx and ti,omap36xx are legacy and
ti,omap3430 and ti,omap3630 are now official.
Heh :) Anyways, with that changed, this looks good to me:
PATCH 2/4 ARM: dts: replace opp-v1 tables by opp-v2 for omap34xx and omap36xx
In reply to H. Nikolaus SchallerIn addition, move omap3 from whitelist to blacklist in cpufreq-dt-platdev in the same patch, because doing either first breaks operation and may make trouble in bisect.
We also can remove opp-v1 table for omap3-n950-n9 since it is now automatically detected.
We also fix a wrong OPP4 voltage for omap3430 which must be 0.6V + 54*12.5mV = 1275mV. Otherwise the twl4030 driver will reject this OPP.
--- arch/arm/boot/dts/omap3-n950-n9.dtsi | 7 --- arch/arm/boot/dts/omap34xx.dtsi | 65 ++++++++++++++++++++++++---- arch/arm/boot/dts/omap36xx.dtsi | 53 +++++++++++++++++++---- drivers/cpufreq/cpufreq-dt-platdev.c | 2 +- 4 files changed, 102 insertions(+), 25 deletions(-)
arch/arm/boot/dts/omap3-n950-n9.dtsi +0 -7
@@ -11,13 +11,6 @@ cpus { cpu@0 { cpu0-supply = <&vcc>; - operating-points = < - /* kHz uV */ - 300000 1012500 - 600000 1200000 - 800000 1325000 - 1000000 1375000 - >; }; };
arch/arm/boot/dts/omap34xx.dtsi +56 -9
75 lines not on this page · raw message
arch/arm/boot/dts/omap36xx.dtsi +45 -8
60 lines not on this page · raw message
drivers/cpufreq/cpufreq-dt-platdev.c +1 -1
@@ -86,7 +86,6 @@ static const struct of_device_id whitelist[] __initconst = { { .compatible = "st-ericsson,u9540", }, { .compatible = "ti,omap2", }, - { .compatible = "ti,omap3", }, { .compatible = "ti,omap4", }, { .compatible = "ti,omap5", },
@@ -132,6 +131,7 @@ static const struct of_device_id blacklist[] __initconst = { { .compatible = "ti,am33xx", }, { .compatible = "ti,am43", }, { .compatible = "ti,dra7", }, + { .compatible = "ti,omap3", }, { } };
Signature · 1 line
2.19.1
Re: [PATCH 2/4] ARM: dts: replace opp-v1 tables by opp-v2 for omap34xx and omap36xx
Quoted 4 lines · H. Nikolaus Schaller
In addition, move omap3 from whitelist to blacklist in cpufreq-dt-platdev in the same patch, because doing either first breaks operation and may make trouble in bisect.
Quoted 8 lines
We also can remove opp-v1 table for omap3-n950-n9 since it is now automatically detected.
We also fix a wrong OPP4 voltage for omap3430 which must be 0.6V + 54*12.5mV = 1275mV. Otherwise the twl4030 driver will reject this OPP.
Signed-off-by H. Nikolaus Schaller <[email protected]>
PATCH 3/4 ARM: dts: omap3: bulk convert compatible to be explicitly ti,omap3430 or ti,omap3630 or ti,am3517
In reply to H. Nikolaus SchallerFor the ti-cpufreq driver we need a clear separation between omap34 and omap36 families since they have different silicon revisions and efuses.
So far ti,omap3630/ti,omap36xx is just an additional flag to ti,omap3 while omap34 has no required entry.
Therefore we can not match omap34 boards properly.
This needs to add ti,omap3430 and ti,omap3630 where it is missing.
We also clean up some instances of missing ti,am3517 so that we can rely on seeing either one of:
ti,am3517
ti,omap3430
ti,omap3630
in addition to ti,omap3.
We leave ti,omap34xx and ti,omap36xx untouched for compatibility.
The script to do the conversion is:
find arch/arm/boot/dts -name '*.dts*' -exec fgrep -q '"ti,omap34xx"' {} \; ! -exec fgrep -q '"ti,omap3430"' {} \; -exec sed -i '' 's/"ti,omap34xx"/"ti,omap3430", "ti,omap34xx"/' {} \;
find arch/arm/boot/dts -name '*.dts*' -exec fgrep -q '"ti,omap36xx"' {} \; ! -exec fgrep -q '"ti,omap3630"' {} \; -exec sed -i '' 's/"ti,omap36xx"/"ti,omap3630", "ti,omap36xx"/' {} \;
find arch/arm/boot/dts \( -name 'omap*.dts*' -o -name 'logic*.dts*' \) -exec fgrep -q '"ti,omap3"' {} \; ! -exec fgrep -q '"ti,omap3630"' {} \; ! -exec fgrep -q '"ti,omap36xx"' {} \; ! -exec fgrep -q '"ti,am3517"' {} \; ! -exec fgrep -q '"ti,omap34xx"' {} \; ! -exec fgrep -q '"ti,omap3430"' {} \; -exec sed -i '' 's/"ti,omap3"/"ti,omap3430", "ti,omap3"/' {} \;
So if your out-of-tree omap3 board does not show any OPPs, please check the compatibility entry and update if needed.
--- arch/arm/boot/dts/am3517_mt_ventoux.dts | 2 +- arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts | 2 +- arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts | 2 +- arch/arm/boot/dts/omap3-beagle-xm.dts | 2 +- arch/arm/boot/dts/omap3-beagle.dts | 2 +- arch/arm/boot/dts/omap3-cm-t3530.dts | 2 +- arch/arm/boot/dts/omap3-cm-t3730.dts | 2 +- arch/arm/boot/dts/omap3-devkit8000-lcd43.dts | 2 +- arch/arm/boot/dts/omap3-devkit8000-lcd70.dts | 2 +- arch/arm/boot/dts/omap3-devkit8000.dts | 2 +- arch/arm/boot/dts/omap3-gta04.dtsi | 2 +- arch/arm/boot/dts/omap3-ha-lcd.dts | 2 +- arch/arm/boot/dts/omap3-ha.dts | 2 +- arch/arm/boot/dts/omap3-igep0020-rev-f.dts | 2 +- arch/arm/boot/dts/omap3-igep0020.dts | 2 +- arch/arm/boot/dts/omap3-igep0030-rev-g.dts | 2 +- arch/arm/boot/dts/omap3-igep0030.dts | 2 +- arch/arm/boot/dts/omap3-ldp.dts | 2 +- arch/arm/boot/dts/omap3-lilly-a83x.dtsi | 2 +- arch/arm/boot/dts/omap3-lilly-dbb056.dts | 2 +- arch/arm/boot/dts/omap3-n9.dts | 2 +- arch/arm/boot/dts/omap3-n950.dts | 2 +- arch/arm/boot/dts/omap3-overo-storm-alto35.dts | 2 +- arch/arm/boot/dts/omap3-overo-storm-chestnut43.dts | 2 +- arch/arm/boot/dts/omap3-overo-storm-gallop43.dts | 2 +- arch/arm/boot/dts/omap3-overo-storm-palo35.dts | 2 +- arch/arm/boot/dts/omap3-overo-storm-palo43.dts | 2 +- arch/arm/boot/dts/omap3-overo-storm-summit.dts | 2 +- arch/arm/boot/dts/omap3-overo-storm-tobi.dts | 2 +- arch/arm/boot/dts/omap3-overo-storm-tobiduo.dts | 2 +- arch/arm/boot/dts/omap3-pandora-1ghz.dts | 2 +- arch/arm/boot/dts/omap3-sbc-t3530.dts | 2 +- arch/arm/boot/dts/omap3-sbc-t3730.dts | 2 +- arch/arm/boot/dts/omap3-sniper.dts | 2 +- arch/arm/boot/dts/omap3-thunder.dts | 2 +- arch/arm/boot/dts/omap3-zoom3.dts | 2 +- arch/arm/boot/dts/omap3430-sdp.dts | 2 +- 37 files changed, 37 insertions(+), 37 deletions(-)
arch/arm/boot/dts/am3517_mt_ventoux.dts +1 -1
@@ -8,7 +8,7 @@ / { model = "TeeJet Mt.Ventoux"; - compatible = "teejet,mt_ventoux", "ti,omap3"; + compatible = "teejet,mt_ventoux", "ti,am3517", "ti,omap3"; memory@80000000 { device_type = "memory";
arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts +1 -1
@@ -9,5 +9,5 @@ / { model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit"; - compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3"; + compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3430", "ti,omap3"; };
arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts +1 -1
@@ -9,5 +9,5 @@ / { model = "LogicPD Zoom OMAP35xx Torpedo Development Kit"; - compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3"; + compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3430", "ti,omap3"; };
arch/arm/boot/dts/omap3-beagle-xm.dts +1 -1
@@ -8,7 +8,7 @@ / { model = "TI OMAP3 BeagleBoard xM"; - compatible = "ti,omap3-beagle-xm", "ti,omap36xx", "ti,omap3"; + compatible = "ti,omap3-beagle-xm", "ti,omap3630", "ti,omap36xx", "ti,omap3"; cpus { cpu@0 {
arch/arm/boot/dts/omap3-beagle.dts +1 -1
@@ -8,7 +8,7 @@ / { model = "TI OMAP3 BeagleBoard"; - compatible = "ti,omap3-beagle", "ti,omap3"; + compatible = "ti,omap3-beagle", "ti,omap3430", "ti,omap3"; cpus { cpu@0 {
arch/arm/boot/dts/omap3-cm-t3530.dts +1 -1
@@ -9,7 +9,7 @@ / { model = "CompuLab CM-T3530"; - compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3"; + compatible = "compulab,omap3-cm-t3530", "ti,omap3430", "ti,omap34xx", "ti,omap3"; /* Regulator to trigger the reset signal of the Wifi module */ mmc2_sdio_reset: regulator-mmc2-sdio-reset {
arch/arm/boot/dts/omap3-cm-t3730.dts +1 -1
@@ -9,7 +9,7 @@ / { model = "CompuLab CM-T3730"; - compatible = "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3"; + compatible = "compulab,omap3-cm-t3730", "ti,omap3630", "ti,omap36xx", "ti,omap3"; wl12xx_vmmc2: wl12xx_vmmc2 { compatible = "regulator-fixed";
arch/arm/boot/dts/omap3-devkit8000-lcd43.dts +1 -1
@@ -11,7 +11,7 @@ #include "omap3-devkit8000-lcd-common.dtsi" / { model = "TimLL OMAP3 Devkit8000 with 4.3'' LCD panel"; - compatible = "timll,omap3-devkit8000", "ti,omap3"; + compatible = "timll,omap3-devkit8000", "ti,omap3430", "ti,omap3"; lcd0: display { panel-timing {
arch/arm/boot/dts/omap3-devkit8000-lcd70.dts +1 -1
@@ -11,7 +11,7 @@ #include "omap3-devkit8000-lcd-common.dtsi" / { model = "TimLL OMAP3 Devkit8000 with 7.0'' LCD panel"; - compatible = "timll,omap3-devkit8000", "ti,omap3"; + compatible = "timll,omap3-devkit8000", "ti,omap3430", "ti,omap3"; lcd0: display { panel-timing {
arch/arm/boot/dts/omap3-devkit8000.dts +1 -1
@@ -7,7 +7,7 @@ #include "omap3-devkit8000-common.dtsi" / { model = "TimLL OMAP3 Devkit8000"; - compatible = "timll,omap3-devkit8000", "ti,omap3"; + compatible = "timll,omap3-devkit8000", "ti,omap3430", "ti,omap3"; aliases { display1 = &dvi0;
arch/arm/boot/dts/omap3-gta04.dtsi +1 -1
@@ -11,7 +11,7 @@ / { model = "OMAP3 GTA04"; - compatible = "ti,omap3-gta04", "ti,omap36xx", "ti,omap3"; + compatible = "ti,omap3-gta04", "ti,omap3630", "ti,omap36xx", "ti,omap3"; cpus { cpu@0 {
arch/arm/boot/dts/omap3-ha-lcd.dts +1 -1
@@ -8,7 +8,7 @@ / { model = "TI OMAP3 HEAD acoustics LCD-baseboard with TAO3530 SOM"; - compatible = "headacoustics,omap3-ha-lcd", "technexion,omap3-tao3530", "ti,omap34xx", "ti,omap3"; + compatible = "headacoustics,omap3-ha-lcd", "technexion,omap3-tao3530", "ti,omap3430", "ti,omap34xx", "ti,omap3"; }; &omap3_pmx_core {
arch/arm/boot/dts/omap3-ha.dts +1 -1
@@ -8,7 +8,7 @@ / { model = "TI OMAP3 HEAD acoustics baseboard with TAO3530 SOM"; - compatible = "headacoustics,omap3-ha", "technexion,omap3-tao3530", "ti,omap34xx", "ti,omap3"; + compatible = "headacoustics,omap3-ha", "technexion,omap3-tao3530", "ti,omap3430", "ti,omap34xx", "ti,omap3"; }; &omap3_pmx_core {
arch/arm/boot/dts/omap3-igep0020-rev-f.dts +1 -1
@@ -10,7 +10,7 @@ / { model = "IGEPv2 Rev. F (TI OMAP AM/DM37x)"; - compatible = "isee,omap3-igep0020-rev-f", "ti,omap36xx", "ti,omap3"; + compatible = "isee,omap3-igep0020-rev-f", "ti,omap3630", "ti,omap36xx", "ti,omap3"; /* Regulator to trigger the WL_EN signal of the Wifi module */ lbep5clwmc_wlen: regulator-lbep5clwmc-wlen {
arch/arm/boot/dts/omap3-igep0020.dts +1 -1
@@ -10,7 +10,7 @@ / { model = "IGEPv2 Rev. C (TI OMAP AM/DM37x)"; - compatible = "isee,omap3-igep0020", "ti,omap36xx", "ti,omap3"; + compatible = "isee,omap3-igep0020", "ti,omap3630", "ti,omap36xx", "ti,omap3"; vmmcsdio_fixed: fixedregulator-mmcsdio { compatible = "regulator-fixed";
arch/arm/boot/dts/omap3-igep0030-rev-g.dts +1 -1
@@ -10,7 +10,7 @@ / { model = "IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)"; - compatible = "isee,omap3-igep0030-rev-g", "ti,omap36xx", "ti,omap3"; + compatible = "isee,omap3-igep0030-rev-g", "ti,omap3630", "ti,omap36xx", "ti,omap3"; /* Regulator to trigger the WL_EN signal of the Wifi module */ lbep5clwmc_wlen: regulator-lbep5clwmc-wlen {
arch/arm/boot/dts/omap3-igep0030.dts +1 -1
@@ -10,7 +10,7 @@ / { model = "IGEP COM MODULE Rev. E (TI OMAP AM/DM37x)"; - compatible = "isee,omap3-igep0030", "ti,omap36xx", "ti,omap3"; + compatible = "isee,omap3-igep0030", "ti,omap3630", "ti,omap36xx", "ti,omap3"; vmmcsdio_fixed: fixedregulator-mmcsdio { compatible = "regulator-fixed";
arch/arm/boot/dts/omap3-ldp.dts +1 -1
@@ -10,7 +10,7 @@ / { model = "TI OMAP3430 LDP (Zoom1 Labrador)"; - compatible = "ti,omap3-ldp", "ti,omap3"; + compatible = "ti,omap3-ldp", "ti,omap3430", "ti,omap3"; memory@80000000 { device_type = "memory";
arch/arm/boot/dts/omap3-lilly-a83x.dtsi +1 -1
@@ -7,7 +7,7 @@ / { model = "INCOstartec LILLY-A83X module (DM3730)"; - compatible = "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3"; + compatible = "incostartec,omap3-lilly-a83x", "ti,omap3630", "ti,omap36xx", "ti,omap3"; chosen { bootargs = "console=ttyO0,115200n8 vt.global_cursor_default=0 consoleblank=0";
arch/arm/boot/dts/omap3-lilly-dbb056.dts +1 -1
@@ -8,7 +8,7 @@ / { model = "INCOstartec LILLY-DBB056 (DM3730)"; - compatible = "incostartec,omap3-lilly-dbb056", "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3"; + compatible = "incostartec,omap3-lilly-dbb056", "incostartec,omap3-lilly-a83x", "ti,omap3630", "ti,omap36xx", "ti,omap3"; }; &twl {
arch/arm/boot/dts/omap3-n9.dts +1 -1
@@ -12,7 +12,7 @@ / { model = "Nokia N9"; - compatible = "nokia,omap3-n9", "ti,omap36xx", "ti,omap3"; + compatible = "nokia,omap3-n9", "ti,omap3630", "ti,omap36xx", "ti,omap3"; }; &i2c2 {
arch/arm/boot/dts/omap3-n950.dts +1 -1
@@ -12,7 +12,7 @@ / { model = "Nokia N950"; - compatible = "nokia,omap3-n950", "ti,omap36xx", "ti,omap3"; + compatible = "nokia,omap3-n950", "ti,omap3630", "ti,omap36xx", "ti,omap3"; keys { compatible = "gpio-keys";
arch/arm/boot/dts/omap3-overo-storm-alto35.dts +1 -1
@@ -14,5 +14,5 @@ / { model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Alto35"; - compatible = "gumstix,omap3-overo-alto35", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; + compatible = "gumstix,omap3-overo-alto35", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3"; };
arch/arm/boot/dts/omap3-overo-storm-chestnut43.dts +1 -1
@@ -14,7 +14,7 @@ / { model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Chestnut43"; - compatible = "gumstix,omap3-overo-chestnut43", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; + compatible = "gumstix,omap3-overo-chestnut43", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3"; }; &omap3_pmx_core2 {
arch/arm/boot/dts/omap3-overo-storm-gallop43.dts +1 -1
@@ -14,7 +14,7 @@ / { model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Gallop43"; - compatible = "gumstix,omap3-overo-gallop43", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; + compatible = "gumstix,omap3-overo-gallop43", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3"; }; &omap3_pmx_core2 {
arch/arm/boot/dts/omap3-overo-storm-palo35.dts +1 -1
@@ -14,7 +14,7 @@ / { model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Palo35"; - compatible = "gumstix,omap3-overo-palo35", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; + compatible = "gumstix,omap3-overo-palo35", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3"; }; &omap3_pmx_core2 {
arch/arm/boot/dts/omap3-overo-storm-palo43.dts +1 -1
@@ -14,7 +14,7 @@ / { model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Palo43"; - compatible = "gumstix,omap3-overo-palo43", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; + compatible = "gumstix,omap3-overo-palo43", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3"; }; &omap3_pmx_core2 {
arch/arm/boot/dts/omap3-overo-storm-summit.dts +1 -1
@@ -14,7 +14,7 @@ / { model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Summit"; - compatible = "gumstix,omap3-overo-summit", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; + compatible = "gumstix,omap3-overo-summit", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3"; }; &omap3_pmx_core2 {
arch/arm/boot/dts/omap3-overo-storm-tobi.dts +1 -1
@@ -14,6 +14,6 @@ / { model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Tobi"; - compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; + compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3"; };
arch/arm/boot/dts/omap3-overo-storm-tobiduo.dts +1 -1
@@ -14,5 +14,5 @@ / { model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on TobiDuo"; - compatible = "gumstix,omap3-overo-tobiduo", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; + compatible = "gumstix,omap3-overo-tobiduo", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3"; };
arch/arm/boot/dts/omap3-pandora-1ghz.dts +1 -1
@@ -16,7 +16,7 @@ / { model = "Pandora Handheld Console 1GHz"; - compatible = "openpandora,omap3-pandora-1ghz", "ti,omap36xx", "ti,omap3"; + compatible = "openpandora,omap3-pandora-1ghz", "ti,omap3630", "ti,omap36xx", "ti,omap3"; }; &omap3_pmx_core2 {
arch/arm/boot/dts/omap3-sbc-t3530.dts +1 -1
@@ -8,7 +8,7 @@ / { model = "CompuLab SBC-T3530 with CM-T3530"; - compatible = "compulab,omap3-sbc-t3530", "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3"; + compatible = "compulab,omap3-sbc-t3530", "compulab,omap3-cm-t3530", "ti,omap3430", "ti,omap34xx", "ti,omap3"; aliases { display0 = &dvi0;
arch/arm/boot/dts/omap3-sbc-t3730.dts +1 -1
@@ -8,7 +8,7 @@ / { model = "CompuLab SBC-T3730 with CM-T3730"; - compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3"; + compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap3630", "ti,omap36xx", "ti,omap3"; aliases { display0 = &dvi0;
arch/arm/boot/dts/omap3-sniper.dts +1 -1
@@ -9,7 +9,7 @@ / { model = "LG Optimus Black"; - compatible = "lg,omap3-sniper", "ti,omap36xx", "ti,omap3"; + compatible = "lg,omap3-sniper", "ti,omap3630", "ti,omap36xx", "ti,omap3"; cpus { cpu@0 {
arch/arm/boot/dts/omap3-thunder.dts +1 -1
@@ -8,7 +8,7 @@ / { model = "TI OMAP3 Thunder baseboard with TAO3530 SOM"; - compatible = "technexion,omap3-thunder", "technexion,omap3-tao3530", "ti,omap34xx", "ti,omap3"; + compatible = "technexion,omap3-thunder", "technexion,omap3-tao3530", "ti,omap3430", "ti,omap34xx", "ti,omap3"; }; &omap3_pmx_core {
arch/arm/boot/dts/omap3-zoom3.dts +1 -1
@@ -9,7 +9,7 @@ / { model = "TI Zoom3"; - compatible = "ti,omap3-zoom3", "ti,omap36xx", "ti,omap3"; + compatible = "ti,omap3-zoom3", "ti,omap3630", "ti,omap36xx", "ti,omap3"; cpus { cpu@0 {
arch/arm/boot/dts/omap3430-sdp.dts +1 -1
@@ -8,7 +8,7 @@ / { model = "TI OMAP3430 SDP"; - compatible = "ti,omap3430-sdp", "ti,omap3"; + compatible = "ti,omap3430-sdp", "ti,omap3430", "ti,omap3"; memory@80000000 { device_type = "memory";
Signature · 1 line
2.19.1
Re: [PATCH 3/4] ARM: dts: omap3: bulk convert compatible to be explicitly ti,omap3430 or ti,omap3630 or ti,am3517
Quoted 13 lines · H. Nikolaus Schaller
For the ti-cpufreq driver we need a clear separation between omap34 and omap36 families since they have different silicon revisions and efuses.
So far ti,omap3630/ti,omap36xx is just an additional flag to ti,omap3 while omap34 has no required entry.
Therefore we can not match omap34 boards properly.
This needs to add ti,omap3430 and ti,omap3630 where it is missing.
We also clean up some instances of missing ti,am3517 so that we can rely on seeing either one of:
Quoted 7 lines
ti,am3517
ti,omap3430
ti,omap3630in addition to ti,omap3.
We leave ti,omap34xx and ti,omap36xx untouched for compatibility.
Thanks for doing this:
PATCH 4/4 DTS: bindings: omap: update bindings documentation
In reply to H. Nikolaus Schaller* clarify that we now need either "ti,omap3430" or "ti,omap3630" or "ti,am3517" for omap3 chips
* clarify that "ti,omap3" has no default
* clarify that AM33x is not an "ti,omap3"
* clarify that the list of boards is incomplete
* remove some "ti,am33xx", "ti,omap3"
* add some missing "ti,omap4"
--- .../devicetree/bindings/arm/omap/omap.txt | 30 +++++++++++-------- 1 file changed, 17 insertions(+), 13 deletions(-)
Documentation/devicetree/bindings/arm/omap/omap.txt +17 -13
@@ -43,7 +43,7 @@ SoC Families: - OMAP2 generic - defaults to OMAP2420 compatible = "ti,omap2" -- OMAP3 generic - defaults to OMAP3430 +- OMAP3 generic compatible = "ti,omap3" - OMAP4 generic - defaults to OMAP4430 compatible = "ti,omap4"
@@ -51,6 +51,8 @@ SoC Families: compatible = "ti,omap5" - DRA7 generic - defaults to DRA742 compatible = "ti,dra7" +- AM33x generic + compatible = "ti,am33xx" - AM43x generic - defaults to AM4372 compatible = "ti,am43"
@@ -63,12 +65,14 @@ SoCs: - OMAP3430 compatible = "ti,omap3430", "ti,omap3" + legacy: "ti,omap34xx" - please do not use any more - AM3517 compatible = "ti,am3517", "ti,omap3" - OMAP3630 - compatible = "ti,omap36xx", "ti,omap3" -- AM33xx - compatible = "ti,am33xx", "ti,omap3" + compatible = "ti,omap3630", "ti,omap3" + legacy: "ti,omap36xx" - please do not use any more +- AM335x + compatible = "ti,am33xx" - OMAP4430 compatible = "ti,omap4430", "ti,omap4"
@@ -110,19 +114,19 @@ SoCs: - AM4372 compatible = "ti,am4372", "ti,am43" -Boards: +Boards (incomplete list of examples): - OMAP3 BeagleBoard : Low cost community board - compatible = "ti,omap3-beagle", "ti,omap3" + compatible = "ti,omap3-beagle", "ti,omap3430", "ti,omap3" - OMAP3 Tobi with Overo : Commercial expansion board with daughter board - compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3" + compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3430", "ti,omap3" - OMAP4 SDP : Software Development Board - compatible = "ti,omap4-sdp", "ti,omap4430" + compatible = "ti,omap4-sdp", "ti,omap4430", "ti,omap4" - OMAP4 PandaBoard : Low cost community board - compatible = "ti,omap4-panda", "ti,omap4430" + compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4" - OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4";
@@ -134,16 +138,16 @@ Boards: compatible = "variscite,var-dvk-om44", "variscite,var-som-om44", "ti,omap4460", "ti,omap4"; - OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x - compatible = "ti,omap3-evm", "ti,omap3" + compatible = "ti,omap3-evm", "ti,omap3630", "ti,omap3" - AM335X EVM : Software Development Board for AM335x - compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3" + compatible = "ti,am335x-evm", "ti,am33xx" - AM335X Bone : Low cost community board - compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3" + compatible = "ti,am335x-bone", "ti,am33xx" - AM3359 ICEv2 : Low cost Industrial Communication Engine EVM. - compatible = "ti,am3359-icev2", "ti,am33xx", "ti,omap3" + compatible = "ti,am3359-icev2", "ti,am33xx" - AM335X OrionLXm : Substation Automation Platform compatible = "novatech,am335x-lxm", "ti,am33xx"
Signature · 1 line
2.19.1
Re: [PATCH 4/4] DTS: bindings: omap: update bindings documentation
Quoted 6 lines · H. Nikolaus Schaller
* clarify that we now need either "ti,omap3430" or "ti,omap3630" or "ti,am3517" for omap3 chips
* clarify that "ti,omap3" has no default
* clarify that AM33x is not an "ti,omap3"
* clarify that the list of boards is incomplete
* remove some "ti,am33xx", "ti,omap3"
* add some missing "ti,omap4"