Skip to contentSkip to conversation

staging: wilc1000: remove unused interrupt status handling code

PATCH New [email protected] 1 participant 2 messages Sep 10, 2019 Staging

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 staging: wilc1000: remove unused interrupt status handling code

From: Ajay Singh <[email protected]>

Remove interrupt handling for unused interrupt status(PLL update and Sleep). The firmware only initiates the interrupt for the data transfer to host and rest are not used anymore.

---
 drivers/staging/wilc1000/wilc_wlan.c | 26 --------------------------
 drivers/staging/wilc1000/wilc_wlan.h | 10 ++--------
 2 files changed, 2 insertions(+), 34 deletions(-)
drivers/staging/wilc1000/wilc_wlan.c +0 -26
index 2bbb359d2119..771d8cb68dc1 100644
@@ -758,26 +758,6 @@ static void wilc_unknown_isr_ext(struct wilc *wilc)
 	wilc->hif_func->hif_clear_int_ext(wilc, 0);
 }
 
-static void wilc_pllupdate_isr_ext(struct wilc *wilc, u32 int_stats)
-{
-	int trials = 10;
-
-	wilc->hif_func->hif_clear_int_ext(wilc, PLL_INT_CLR);
-
-	if (wilc->io_type == WILC_HIF_SDIO)
-		mdelay(WILC_PLL_TO_SDIO);
-	else
-		mdelay(WILC_PLL_TO_SPI);
-
-	while (!(is_wilc1000(wilc_get_chipid(wilc, true)) && --trials))
-		mdelay(1);
-}
-
-static void wilc_sleeptimer_isr_ext(struct wilc *wilc, u32 int_stats1)
-{
-	wilc->hif_func->hif_clear_int_ext(wilc, SLEEP_INT_CLR);
-}
-
 static void wilc_wlan_handle_isr_ext(struct wilc *wilc, u32 int_status)
 {
 	u32 offset = wilc->rx_buffer_offset;
@@ -827,15 +807,9 @@ void wilc_handle_isr(struct wilc *wilc)
 	acquire_bus(wilc, WILC_BUS_ACQUIRE_AND_WAKEUP);
 	wilc->hif_func->hif_read_int(wilc, &int_status);
 
-	if (int_status & PLL_INT_EXT)
-		wilc_pllupdate_isr_ext(wilc, int_status);
-
 	if (int_status & DATA_INT_EXT)
 		wilc_wlan_handle_isr_ext(wilc, int_status);
 
-	if (int_status & SLEEP_INT_EXT)
-		wilc_sleeptimer_isr_ext(wilc, int_status);
-
 	if (!(int_status & (ALL_INT_EXT)))
 		wilc_unknown_isr_ext(wilc);
 
drivers/staging/wilc1000/wilc_wlan.h +2 -8
index f566d040bb72..7469fa47d588 100644
@@ -128,8 +128,6 @@
 #define WILC_CFG_RSP_STATUS	2
 #define WILC_CFG_RSP_SCAN	3
 
-#define WILC_PLL_TO_SDIO	4
-#define WILC_PLL_TO_SPI		2
 #define WILC_ABORT_REQ_BIT		BIT(31)
 
 #define WILC_RX_BUFF_SIZE	(96 * 1024)
@@ -185,14 +183,10 @@
 #define EN_VMM			BIT(8)
 
 #define DATA_INT_EXT		INT_0
-#define PLL_INT_EXT		INT_1
-#define SLEEP_INT_EXT		INT_2
-#define ALL_INT_EXT		(DATA_INT_EXT | PLL_INT_EXT | SLEEP_INT_EXT)
-#define NUM_INT_EXT		3
+#define ALL_INT_EXT		DATA_INT_EXT
+#define NUM_INT_EXT		1
 
 #define DATA_INT_CLR		CLR_INT0
-#define PLL_INT_CLR		CLR_INT1
-#define SLEEP_INT_CLR		CLR_INT2
 
 #define ENABLE_RX_VMM		(SEL_VMM_TBL1 | EN_VMM)
 #define ENABLE_TX_VMM		(SEL_VMM_TBL0 | EN_VMM)
Signature · 1 line
2.22.0
#1 lore raw

PATCH 2/2 staging: wilc1000: avoid twice IRQ handler execution for each single interrupt

From: Ajay Singh <[email protected]>

The IRQ handler(isr_bh_routine()) was called twice for each interrupt from firmware. The data was read completely during the first call and the second call was doing nothing.
Now changed the IRQ flag from ‘level’ to ‘edge’ trigger i.e IRQF_TRIGGER_LOW to IRQF_TRIGGER_FALLING to avoid extra interrupt trigger.

---
 drivers/staging/wilc1000/wilc_netdev.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/staging/wilc1000/wilc_netdev.c +1 -1
index cd11c35adcfe..508acb8bb089 100644
@@ -60,7 +60,7 @@ static int init_irq(struct net_device *dev)
 
 	ret = request_threaded_irq(wl->dev_irq_num, isr_uh_routine,
 				   isr_bh_routine,
-				   IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+				   IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 				   "WILC_IRQ", dev);
 	if (ret < 0)
 		netdev_err(dev, "Failed to request IRQ\n");
Signature · 1 line
2.22.0