Revert "configs: Remove am335x_boneblack_defconfig"
PATCH 1/2 Revert "configs: Remove am335x_boneblack_defconfig"
Commit 8fa7f65dd02c ("configs: Remove am335x_boneblack_defconfig") removes defconfig for BeagleBone Black board, and it's advised to use am335x_evm_defconfig for all AM335x boards. But it's impossible to use am335x_evm_defconfig in eMMC use-case without modifications for BBB (NAND must be disabled, MMC enabled, etc). This is inconvenient for user to do such modifications via menuconfig (only developer knows what should be done). Furthermore, enabling MMC options in am335x_evm_defconfig leads to wrong pin-muxing scheme in board/ti/am335x/mux.c, because both NAND and MMC options are going to be enabled in the config, so that pins are muxed for BBB with NAND cape, which in turn leads to non-functioning eMMC. There is no way to make the single defconfig working for both eMMC and NAND use-cases, because we can't figure out in run-time which board configuration is used by user (EVM, BBB, or BBB with NAND cape). Hence we rely on CONFIG options to figure out which configuration is used. Because of this we can't use single defconfig for AM335x EVM and BBB.
All that said, let's bring back am335x_boneblack_defconfig, because right now users are not able to use U-Boot for BBB. Further patch will update this defconfig by enabling Driver Model and pulling some other useful options from am335x_evm_defconfig.
--- configs/am335x_boneblack_defconfig | 50 ++++++++++++++++++++++++++++++ 1 file changed, 50 insertions(+) create mode 100644 configs/am335x_boneblack_defconfig
configs/am335x_boneblack_defconfig new file +50 -0
@@ -0,0 +1,50 @@ +CONFIG_ARM=y +CONFIG_ARCH_OMAP2PLUS=y +CONFIG_TI_COMMON_CMD_OPTIONS=y +CONFIG_AM33XX=y +CONFIG_SPL=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_SYS_EXTRA_OPTIONS="EMMC_BOOT" +CONFIG_BOOTCOMMAND="if test ${boot_fit} -eq 1; then run update_to_fit; fi; run findfdt; run init_console; run envboot; run distro_bootcmd" +CONFIG_SYS_CONSOLE_INFO_QUIET=y +CONFIG_VERSION_VARIABLE=y +CONFIG_ARCH_MISC_INIT=y +CONFIG_SPL_MUSB_NEW_SUPPORT=y +# CONFIG_SPL_NAND_SUPPORT is not set +CONFIG_SPL_OS_BOOT=y +CONFIG_AUTOBOOT_KEYED=y +CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" +CONFIG_AUTOBOOT_DELAY_STR="d" +CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_CMD_SPL=y +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DFU_TFTP=y +CONFIG_DFU_MMC=y +CONFIG_DFU_RAM=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=1 +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_MMC_OMAP_HS=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_MII=y +CONFIG_DRIVER_TI_CPSW=y +CONFIG_SPI=y +CONFIG_OMAP3_SPI=y +CONFIG_USB=y +CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" +CONFIG_USB_GADGET_VENDOR_NUM=0x0451 +CONFIG_USB_GADGET_PRODUCT_NUM=0xd022 +CONFIG_USB_ETHER=y +CONFIG_USBNET_HOST_ADDR="de:ad:be:af:00:00" +CONFIG_LZO=y +CONFIG_OF_LIBFDT=y
Signature · 1 line
2.23.0.rc1
PATCH 1/2 Revert "configs: Remove am335x_boneblack_defconfig"
Quoted 18 lines · Sam Protsenko
Commit
8fa7f65dd02c("configs: Removeam335x_boneblack_defconfig") removes defconfig for BeagleBone Black board, and it's advised to useam335x_evm_defconfigfor all AM335x boards. But it's impossible to useam335x_evm_defconfigin eMMC use-case without modifications for BBB (NAND must be disabled, MMC enabled, etc). This is inconvenient for user to do such modifications via menuconfig (only developer knows what should be done). Furthermore, enabling MMC options inam335x_evm_defconfigleads to wrong pin-muxing scheme inboard/ti/am335x/mux.c, because both NAND and MMC options are going to be enabled in the config, so that pins are muxed for BBB with NAND cape, which in turn leads to non-functioning eMMC. There is no way to make the single defconfig working for both eMMC and NAND use-cases, because we can't figure out in run-time which board configuration is used by user (EVM, BBB, or BBB with NAND cape). Hence we rely on CONFIG options to figure out which configuration is used. Because of this we can't use single defconfig for AM335x EVM and BBB.
Quoted 8 lines
All that said, let's bring back
am335x_boneblack_defconfig, because right now users are not able to use U-Boot for BBB. Further patch will update this defconfig by enabling Driver Model and pulling some other useful options fromam335x_evm_defconfig.Fixes 8fa7f65dd02c ("configs: Remove am335x_boneblack_defconfig")Signed-off-by Sam Protsenko <[email protected]>---
Superseded by v2.
Quoted 63 lines
configs/am335x_boneblack_defconfig | 50 ++++++++++++++++++++++++++++++ 1 file changed, 50 insertions(+) create mode 100644 configs/am335x_boneblack_defconfigconfigs/am335x_boneblack_defconfig new file +50
-1@@ -0,0 +1,50 @@ +CONFIG_ARM=y +CONFIG_ARCH_OMAP2PLUS=y +CONFIG_TI_COMMON_CMD_OPTIONS=y +CONFIG_AM33XX=y +CONFIG_SPL=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_SYS_EXTRA_OPTIONS="EMMC_BOOT" +CONFIG_BOOTCOMMAND="if test ${boot_fit} -eq 1; then run update_to_fit; fi; run findfdt; run init_console; run envboot; run distro_bootcmd" +CONFIG_SYS_CONSOLE_INFO_QUIET=y +CONFIG_VERSION_VARIABLE=y +CONFIG_ARCH_MISC_INIT=y +CONFIG_SPL_MUSB_NEW_SUPPORT=y +# CONFIG_SPL_NAND_SUPPORT is not set +CONFIG_SPL_OS_BOOT=y +CONFIG_AUTOBOOT_KEYED=y +CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" +CONFIG_AUTOBOOT_DELAY_STR="d" +CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_CMD_SPL=y +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DFU_TFTP=y +CONFIG_DFU_MMC=y +CONFIG_DFU_RAM=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=1 +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_MMC_OMAP_HS=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_MII=y +CONFIG_DRIVER_TI_CPSW=y +CONFIG_SPI=y +CONFIG_OMAP3_SPI=y +CONFIG_USB=y +CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" +CONFIG_USB_GADGET_VENDOR_NUM=0x0451 +CONFIG_USB_GADGET_PRODUCT_NUM=0xd022 +CONFIG_USB_ETHER=y +CONFIG_USBNET_HOST_ADDR="de:ad:be:af:00:00" +CONFIG_LZO=y +CONFIG_OF_LIBFDT=y --2.23.0.rc1
PATCH 1/2 Revert "configs: Remove am335x_boneblack_defconfig"
In reply to Sam ProtsenkoHi,
Quoted 8 lines · Sam Protsenko
Commit
8fa7f65dd02c("configs: Removeam335x_boneblack_defconfig") removes defconfig for BeagleBone Black board, and it's advised to useam335x_evm_defconfigfor all AM335x boards. But it's impossible to useam335x_evm_defconfigin eMMC use-case without modifications for BBB (NAND must be disabled, MMC enabled, etc). This is inconvenient for user to do such modifications via menuconfig (only developer knows what should be done). Furthermore, enabling MMC options inam335x_evm_defconfigleads to wrong pin-muxing scheme in
Quoted 8 lines
board/ti/am335x/mux.c, because both NAND and MMC options are going to be enabled in the config, so that pins are muxed for BBB with NAND cape, which in turn leads to non-functioning eMMC. There is no way to make the single defconfig working for both eMMC and NAND use-cases, because we can't figure out in run-time which board configuration is used by user (EVM, BBB, or BBB with NAND cape). Hence we rely on CONFIG options to figure out which configuration is used. Because of this we can't use single defconfig for AM335x EVM and BBB.
for the record: I booted my bbb with am335x_evm_defconfig without any config changes from emmc using master a few days ago just fine. It works just as well as booting from sd card.
That's with using distro boot, the legacy env cmds don't try to boot off emmc iirc.
Regards,
Andre
PATCH 1/2 Revert "configs: Remove am335x_boneblack_defconfig"
The eMMC boot works fine, but "env save" fails with message:
Saving Environment to FAT... Failed (1)
That's because CONFIG_ENV_IS_IN_MMC=y is not enabled, which wouldn't work without CONFIG_SYS_EXTRA_OPTIONS="EMMC_BOOT", because in include/configs/am335x_evm.h it defines eMMC environment options:
...
#elif defined(CONFIG_EMMC_BOOT)
#define CONFIG_SYS_MMC_ENV_DEV 1
#define CONFIG_SYS_MMC_ENV_PART 0
#define CONFIG_ENV_OFFSET 0x260000
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_SYS_MMC_MAX_DEVICE 2And if we enable those two options in am335x_evm_defconfig, it leads to wrong pin-muxing in board/ti/am335x/mux.c (because CONFIG_NAND is also enabled in am335x_evm_defconfig):
} else if (board_is_bone_lt()) {
...
configure_module_pin_mux(mmc0_pin_mux);
#if defined(CONFIG_NAND) && defined(CONFIG_EMMC_BOOT)
configure_module_pin_mux(nand_pin_mux); <---- this line is executed
#elif defined(CONFIG_NOR) && defined(CONFIG_EMMC_BOOT)
configure_module_pin_mux(bone_norcape_pin_mux);
#else
configure_module_pin_mux(mmc1_pin_mux);#endif
So I don't see any other way to overcome this issue other than keeping separate defconfig for NAND and eMMC board variants. Of course, I can fix commit message to state the reason more clearly. We can also rename am335x_boneblack_defconfig to am335x_evm_mmc_defconfig, but it doesn't change the fact it should be done. If somebody sees another way around, please do tell.
Thanks!
Quoted 30 lines · Andre Heider
Hi,
Quoted 8 lines · Sam Protsenko
Commit
8fa7f65dd02c("configs: Removeam335x_boneblack_defconfig") removes defconfig for BeagleBone Black board, and it's advised to useam335x_evm_defconfigfor all AM335x boards. But it's impossible to useam335x_evm_defconfigin eMMC use-case without modifications for BBB (NAND must be disabled, MMC enabled, etc). This is inconvenient for user to do such modifications via menuconfig (only developer knows what should be done). Furthermore, enabling MMC options inam335x_evm_defconfigleads to wrong pin-muxing scheme inQuoted 8 lines
board/ti/am335x/mux.c, because both NAND and MMC options are going to be enabled in the config, so that pins are muxed for BBB with NAND cape, which in turn leads to non-functioning eMMC. There is no way to make the single defconfig working for both eMMC and NAND use-cases, because we can't figure out in run-time which board configuration is used by user (EVM, BBB, or BBB with NAND cape). Hence we rely on CONFIG options to figure out which configuration is used. Because of this we can't use single defconfig for AM335x EVM and BBB.for the record: I booted my bbb with
am335x_evm_defconfigwithout any config changes from emmc using master a few days ago just fine. It works just as well as booting from sd card.That's with using distro boot, the legacy env cmds don't try to boot off emmc iirc.
Regards,
Andre
PATCH 2/2 configs: am335x_boneblack: Sync with am335x_evm
In reply to Sam ProtsenkoOld am335x_boneblack defconfig doesn't have Driver Model enabled. Pull DM options from am335x_evm, along with some others, like ones for shrinking SPL, making am335x_boneblack defconfig as close as possible to am335x_evm.
--- configs/am335x_boneblack_defconfig | 37 ++++++++++++++++++++++++------ 1 file changed, 30 insertions(+), 7 deletions(-)
configs/am335x_boneblack_defconfig +30 -7
@@ -4,23 +4,33 @@ CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_AM33XX=y CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="EMMC_BOOT" CONFIG_BOOTCOMMAND="if test ${boot_fit} -eq 1; then run update_to_fit; fi; run findfdt; run init_console; run envboot; run distro_bootcmd" +CONFIG_LOGLEVEL=3 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_ARCH_MISC_INIT=y +CONFIG_SPL_FIT_IMAGE_TINY=y +CONFIG_SPL_ETH_SUPPORT=y +# CONFIG_SPL_FS_EXT4 is not set CONFIG_SPL_MUSB_NEW_SUPPORT=y # CONFIG_SPL_NAND_SUPPORT is not set +CONFIG_SPL_NET_SUPPORT=y +CONFIG_SPL_NET_VCI_STRING="AM335x U-Boot SPL" CONFIG_SPL_OS_BOOT=y -CONFIG_AUTOBOOT_KEYED=y -CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" -CONFIG_AUTOBOOT_DELAY_STR="d" -CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_ETHER=y CONFIG_CMD_SPL=y # CONFIG_CMD_FLASH is not set # CONFIG_CMD_SETEXPR is not set +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-boneblack" +CONFIG_OF_LIST="am335x-boneblack am335x-bonegreen" CONFIG_ENV_IS_IN_MMC=y CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +CONFIG_SPL_ENV_IS_NOWHERE=y CONFIG_BOOTCOUNT_LIMIT=y CONFIG_DFU_TFTP=y CONFIG_DFU_MMC=y
@@ -29,22 +39,35 @@ CONFIG_USB_FUNCTION_FASTBOOT=y CONFIG_FASTBOOT_FLASH=y CONFIG_FASTBOOT_FLASH_MMC_DEV=1 CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_DM_I2C=y +CONFIG_MISC=y +CONFIG_DM_MMC=y CONFIG_MMC_OMAP_HS=y +CONFIG_DM_SPI_FLASH=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_WINBOND=y +CONFIG_DM_ETH=y CONFIG_MII=y CONFIG_DRIVER_TI_CPSW=y CONFIG_SPI=y +CONFIG_DM_SPI=y CONFIG_OMAP3_SPI=y +CONFIG_TIMER=y +CONFIG_OMAP_TIMER=y CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_DM_USB_GADGET=y +CONFIG_SPL_DM_USB_GADGET=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y -CONFIG_USB_MUSB_DSPS=y +CONFIG_USB_MUSB_TI=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" CONFIG_USB_GADGET_VENDOR_NUM=0x0451 CONFIG_USB_GADGET_PRODUCT_NUM=0xd022 CONFIG_USB_ETHER=y -CONFIG_USBNET_HOST_ADDR="de:ad:be:af:00:00" +# CONFIG_SPL_WDT is not set +CONFIG_DYNAMIC_CRC_TABLE=y +CONFIG_RSA=y CONFIG_LZO=y -CONFIG_OF_LIBFDT=y +# CONFIG_OF_LIBFDT_OVERLAY is not set
Signature · 1 line
2.23.0.rc1