pico-imx6ul: Add DWARF baseboard support
PATCH 1/5 pico-imx6ul: Add DWARF baseboard support
This add the boot menu option for the DWARF baseboard as well as a specific config file for users which wish to use it as a pre-defined board.
---
configs/pico-dwarf-imx6ul_defconfig | 64 +++++++++++++++++++++++++++++ include/configs/pico-imx6ul.h | 6 ++- 2 files changed, 68 insertions(+), 2 deletions(-) create mode 100644 configs/pico-dwarf-imx6ul_defconfig
configs/pico-dwarf-imx6ul_defconfig new file +64 -0
@@ -0,0 +1,64 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX6=y +CONFIG_SYS_TEXT_BASE=0x87800000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_TARGET_PICO_IMX6UL=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL=y +CONFIG_SPL_LIBDISK_SUPPORT=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg" +CONFIG_BOOTDELAY=3 +CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd" +CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-dwarf.dtb" +CONFIG_BOUNCE_BUFFER=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_SPL_USB_HOST_SUPPORT=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y +CONFIG_CMD_BOOTMENU=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_DFU=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="imx6ul-pico-pi" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_DFU_MMC=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_FASTBOOT_BUF_SIZE=0x10000000 +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=0 +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_DM_GPIO=y +CONFIG_DM_I2C=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_PHYLIB=y +CONFIG_PHY_MICREL=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX6=y +CONFIG_DM_PMIC=y +CONFIG_DM_PMIC_PFUZE100=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_PFUZE100=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_USB=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y
include/configs/pico-imx6ul.h +4 -2
@@ -63,9 +63,11 @@ "rootfs part 0 1\0" \#define BOOTMENU_ENV \ - "bootmenu_0=Boot using PICO-Hobbit baseboard=" \ + "bootmenu_0=Boot using PICO-Dwarf baseboard=" \ + "setenv fdtfile imx6ul-pico-dwarf.dtb\0" \ + "bootmenu_1=Boot using PICO-Hobbit baseboard=" \ "setenv fdtfile imx6ul-pico-hobbit.dtb\0" \ - "bootmenu_1=Boot using PICO-Pi baseboard=" \ + "bootmenu_2=Boot using PICO-Pi baseboard=" \ "setenv fdtfile imx6ul-pico-pi.dtb\0" \#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
Signature · 1 line
2.23.0
PATCH 2/5 pico-imx6ul: Increase the CONFIG_ENV_OFFSET size
From: Fabio Estevam <[email protected]>
U-Boot binary has grown in such a way that it goes beyond the reserved area for the environment variables.
Running "saveenv" causes U-Boot to hang because of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem in the future, use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare CONFIG_ENV_OFFSET with its direct value instead.
---
include/configs/pico-imx6ul.h | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-)
include/configs/pico-imx6ul.h +13 -1
@@ -134,7 +134,19 @@/* environment organization */ #define CONFIG_ENV_SIZE SZ_8K -#define CONFIG_ENV_OFFSET (8 * SZ_64K) +/* Environment starts at 768k = 768 * 1024 = 786432 */ +#define CONFIG_ENV_OFFSET 786432 +/* +* Detect overlap between U-Boot image and environment area in build-time +* +* CONFIG_BOARD_SIZE_LIMIT = CONFIG_ENV_OFFSET - u-boot.img offset +* CONFIG_BOARD_SIZE_LIMIT = 768k - 69k = 699k = 715776 +* +* Currently CONFIG_BOARD_SIZE_LIMIT does not handle expressions, so +* write the direct value here +*/ +#define CONFIG_BOARD_SIZE_LIMIT 715776 +#define CONFIG_SYS_MMC_ENV_DEV 0#define CONFIG_SYS_MMC_ENV_PART 0
Signature · 1 line
2.23.0
PATCH 3/5 pico-imx6ul: Add LCD support
In reply to Otavio SalvadorFrom: Fabio Estevam <[email protected]>
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface.
---
board/technexion/pico-imx6ul/pico-imx6ul.c | 55 +++++++++++++++++++++- configs/pico-dwarf-imx6ul_defconfig | 1 + configs/pico-hobbit-imx6ul_defconfig | 1 + configs/pico-imx6ul_defconfig | 1 + configs/pico-pi-imx6ul_defconfig | 1 + include/configs/pico-imx6ul.h | 13 +++++ 6 files changed, 71 insertions(+), 1 deletion(-)
board/technexion/pico-imx6ul/pico-imx6ul.c +54 -1
@@ -42,6 +42,9 @@ DECLARE_GLOBAL_DATA_PTR;#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) +#define LCD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ + PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm) +#define RMII_PHY_RESET IMX_GPIO_NR(1, 28)static iomux_v3_cfg_t const fec_pads[] = {
@@ -105,6 +108,54 @@ static int setup_fec(void)return 0 ; } +#ifdef CONFIG_VIDEO_MXS +static iomux_v3_cfg_t const lcd_pads[] = { +MX6_PAD_LCD_CLK__LCDIF_CLK |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_ENABLE__LCDIF_ENABLE |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_HSYNC__LCDIF_HSYNC |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_VSYNC__LCDIF_VSYNC |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA00__LCDIF_DATA00 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA01__LCDIF_DATA01 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA02__LCDIF_DATA02 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA03__LCDIF_DATA03 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA04__LCDIF_DATA04 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA05__LCDIF_DATA05 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA06__LCDIF_DATA06 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA07__LCDIF_DATA07 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA08__LCDIF_DATA08 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA09__LCDIF_DATA09 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA10__LCDIF_DATA10 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA11__LCDIF_DATA11 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA12__LCDIF_DATA12 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA13__LCDIF_DATA13 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA14__LCDIF_DATA14 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA15__LCDIF_DATA15 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA16__LCDIF_DATA16 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA17__LCDIF_DATA17 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA18__LCDIF_DATA18 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA19__LCDIF_DATA19 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA20__LCDIF_DATA20 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA21__LCDIF_DATA21 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA22__LCDIF_DATA22 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +MX6_PAD_LCD_DATA23__LCDIF_DATA23 |MUX_PAD_CTRL (LCD_PAD_CTRL ), +/* LCD_BLT_CTRL: GPIO for Brightness adjustment */ +MX6_PAD_NAND_ALE__GPIO4_IO10 |MUX_PAD_CTRL (NO_PAD_CTRL ), +/* LCD_VDD_EN: LCD enabled */ +MX6_PAD_JTAG_TMS__GPIO1_IO11 |MUX_PAD_CTRL (NO_PAD_CTRL ), +}; + +void setup_lcd (void ) +{ +imx_iomux_v3_setup_multiple_pads (lcd_pads,ARRAY_SIZE (lcd_pads)); +gpio_request (IMX_GPIO_NR (4 ,10 ),"lcd_brightness" ); +gpio_request (IMX_GPIO_NR (1 ,11 ),"lcd_enable" ); +/* Set Brightness to high */ +gpio_direction_output (IMX_GPIO_NR (4 ,10 ) ,1 ); +/* Set LCD enable to high */ +gpio_direction_output (IMX_GPIO_NR (1 ,11 ) ,1 ); +} +#endif +int board_phy_config (struct phy_device *phydev) {phy_write (phydev,MDIO_DEVAD_NONE ,0x1f ,0x8190 );
@@ -214,7 +265,9 @@ int board_init(void)setup_fec ();setup_usb (); - +#ifdef CONFIG_VIDEO_MXS +setup_lcd (); +#endif return 0 ; }
configs/pico-dwarf-imx6ul_defconfig +1 -0
@@ -62,3 +62,4 @@ CONFIG_USB_GADGET_MANUFACTURER="FSL" CONFIG_USB_GADGET_VENDOR_NUM=0x0525 CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 CONFIG_CI_UDC=y +CONFIG_VIDEO=y
configs/pico-hobbit-imx6ul_defconfig +1 -0
@@ -65,3 +65,4 @@ CONFIG_USB_GADGET_MANUFACTURER="FSL" CONFIG_USB_GADGET_VENDOR_NUM=0x0525 CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 CONFIG_CI_UDC=y +CONFIG_VIDEO=y
configs/pico-imx6ul_defconfig +1 -0
@@ -67,3 +67,4 @@ CONFIG_USB_GADGET_MANUFACTURER="FSL" CONFIG_USB_GADGET_VENDOR_NUM=0x0525 CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 CONFIG_CI_UDC=y +CONFIG_VIDEO=y
configs/pico-pi-imx6ul_defconfig +1 -0
@@ -65,3 +65,4 @@ CONFIG_USB_GADGET_MANUFACTURER="FSL" CONFIG_USB_GADGET_VENDOR_NUM=0x0525 CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 CONFIG_CI_UDC=y +CONFIG_VIDEO=y
include/configs/pico-imx6ul.h +13 -0
@@ -75,10 +75,12 @@#define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ "image=zImage\0" \ + "splashpos=m,m\0" \ "console=ttymxc5\0" \ "fdt_high=0xffffffff\0" \ "initrd_high=0xffffffff\0" \ "fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \ + "videomode=video=ctfb:x:800,y:480,depth:24,mode:0,pclk:30000,le:46,ri:210,up:22,lo:23,hs:20,vs:10,sync:0,vmode:0\0" \ BOOTMENU_ENV \ "fdt_addr=0x83000000\0" \ "fdt_addr_r=0x83000000\0" \
@@ -151,4 +153,15 @@#define CONFIG_SYS_MMC_ENV_DEV 0#define CONFIG_SYS_MMC_ENV_PART 0 +#ifdef CONFIG_VIDEO +#define CONFIG_VIDEO_MXS +#define CONFIG_VIDEO_LOGO +#define CONFIG_SPLASH_SCREEN +#define CONFIG_SPLASH_SCREEN_ALIGN +#define CONFIG_BMP_16BPP +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_VIDEO_BMP_LOGO +#define MXS_LCDIF_BASE MX6UL_LCDIF1_BASE_ADDR +#endif +#endif /* __PICO_IMX6UL_CONFIG_H */
Signature · 1 line
2.23.0
PATCH 4/5 pico-imx6ul: Update the Falcon mode instructions
In reply to Otavio SalvadorFrom: Fabio Estevam <[email protected]>
Sync the Falcon mode instructions with the ones fro pico-imx7d.
---
board/technexion/pico-imx6ul/README | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
board/technexion/pico-imx6ul/README +4 -4
@@ -75,7 +75,7 @@ $ make imx_v6_v7_defconfig (Using the default imx_v6_v7_defconfig configuration just for an example. In order to boot faster the user should customize the defconfig by only enabling the minimal required drivers). -$ make -j4 uImage LOADADDR=0x80800000 +$ make -j4 uImage LOADADDR=0x80008000 $ cp arch/arm/boot/uImage /tftpboot $ cp arch/arm/boot/dts/imx6ul-pico-hobbit.dtb /tftpboot
@@ -93,7 +93,7 @@ Get the kernel: => tftp ${loadaddr} uImage Write the kernel at 2MB offset: -=> mmc write ${loadaddr} 0x1000 0x4000 +=> mmc write ${loadaddr} 0x1000 0x5000 Setup the bootargs: => setenv bootargs 'console=ttymxc5,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait rw'
@@ -104,8 +104,8 @@ Prepare args: Image Name: Linux-4.19.0-rc2-next-20180905-0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 8365608 Bytes = 8 MiB - Load Address: 80800000 - Entry Point: 80800000 + Load Address: 80008000 + Entry Point: 80008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000
Signature · 1 line
2.23.0
PATCH 5/5 pico-imx6ul: Provide a way to escape the Falcon mode
In reply to Otavio SalvadorFrom: Fabio Estevam <[email protected]>
When CONFIG_SPL_OS_BOOT is selected, it is still convenient to be able to escape from Falcon mode and boot to U-Boot proper.
Add a mechanism that allows booting in U-Boot proper when the key 'c' is entered on console at boot time.
---
board/technexion/pico-imx6ul/spl.c | 4 ++++ 1 file changed, 4 insertions(+)
board/technexion/pico-imx6ul/spl.c +4 -0
@@ -19,6 +19,10 @@#ifdef CONFIG_SPL_OS_BOOT int spl_start_uboot (void ) { +/* Break into full U-Boot on 'c' */ +if (serial_tstc () &&serial_getc () =='c' ) +return 1 ; +return 0 ; }#endif
Signature · 1 line
2.23.0
PATCH 1/5 pico-imx6ul: Add DWARF baseboard support
In reply to Otavio SalvadorHi Otavio,
On Thu, 12 Sep 2019 16:01:50 -0300
Otavio Salvador otavio at ossystems.com.br wrote:
...
Quoted 1 line
configs/pico-dwarf-imx6ul_defconfig | 64 +++++++++++++++++++++++++++++
...
Quoted 1 line
+CONFIG_FSL_ESDHC=y
Please change this to CONFIG_FSL_USDHC=y
Otherwise we get build warning/error [1].
[1] https://travis-ci.org/sbabic/u-boot-imx/jobs/584781580#L1287
--
Anatolij
PATCH 1/5 pico-imx6ul: Add DWARF baseboard support
Hi Anatolji,
thanks, I have not sent an e-mail to Otavio after pulling his tree.
Quoted 6 lines · Anatolij Gustschin
Hi Otavio,
On Thu, 12 Sep 2019 16:01:50 -0300
Otavio Salvador otavio at ossystems.com.br wrote:
...Quoted 1 line
configs/pico-dwarf-imx6ul_defconfig | 64 +++++++++++++++++++++++++++++
Quoted 9 lines
...
Quoted 1 line
+CONFIG_FSL_ESDHC=y
Please change this to
CONFIG_FSL_USDHC=yOtherwise we get build warning/error [1].
[1] https://travis-ci.org/sbabic/u-boot-imx/jobs/584781580#L1287
Otavio, I am also fine if you send a follow-up patch to fix it - your decision.
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH 1/1 imx: fix pico-dwarf-imx6ul and pico-dwarf-imx7d build issues
Fixes:
board/technexion/pico-imx6ul/spl.c: In function 'board_mmc_init':
error: implicit declaration of function 'fsl_esdhc_initialize'
and a simmilar error when building pico-dwarf-imx7d.
--- configs/pico-dwarf-imx6ul_defconfig | 2 +- configs/pico-dwarf-imx7d_defconfig | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
configs/pico-dwarf-imx6ul_defconfig +1 -1
@@ -44,7 +44,7 @@ CONFIG_FASTBOOT_CMD_OEM_FORMAT=y CONFIG_DM_GPIO=y CONFIG_DM_I2C=y CONFIG_DM_MMC=y -CONFIG_FSL_ESDHC=y +CONFIG_FSL_USDHC=y CONFIG_PHYLIB=y CONFIG_PHY_MICREL=y CONFIG_MII=y
configs/pico-dwarf-imx7d_defconfig +1 -1
@@ -52,7 +52,7 @@ CONFIG_FASTBOOT_CMD_OEM_FORMAT=y CONFIG_DM_GPIO=y CONFIG_DM_MMC=y CONFIG_SUPPORT_EMMC_BOOT=y -CONFIG_FSL_ESDHC=y +CONFIG_FSL_USDHC=y CONFIG_PHYLIB=y CONFIG_MII=y CONFIG_PINCTRL=y
Signature · 1 line
2.17.1
PATCH 1/1 imx: fix pico-dwarf-imx6ul and pico-dwarf-imx7d build issues
Quoted 9 lines · Anatolij Gustschin
Fixes:
board/technexion/pico-imx6ul/spl.c: In function 'board_mmc_init':
error: implicit declaration of function 'fsl_esdhc_initialize'and a simmilar error when building pico-dwarf-imx7d.
Signed-off-by Anatolij Gustschin <[email protected]>Cc Otavio Salvador <[email protected]>
Signature · 3 lines
Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9 9981-7854 Mobile: +1 (347) 903-9750
Fabio Estevam
reviewerPATCH 1/1 imx: fix pico-dwarf-imx6ul and pico-dwarf-imx7d build issues
In reply to Anatolij GustschinHi Anatolij,
Quoted 5 lines · Anatolij Gustschin
Fixes:
board/technexion/pico-imx6ul/spl.c: In function 'board_mmc_init':
error: implicit declaration of function 'fsl_esdhc_initialize'
Quoted 7 lines
and a simmilar error when building pico-dwarf-imx7d.
Signed-off-by Anatolij Gustschin <[email protected]>Cc Otavio Salvador <[email protected]>--- configs/pico-dwarf-imx6ul_defconfig | 2 +- configs/pico-dwarf-imx7d_defconfig | 2 +-
It seems that configs/pico-nymph-imx7d_defconfig conversion is missing.
I haven't seen your patch earlier and also sent a fix:
https://lists.denx.de/pipermail/u-boot/2019-September/383582.html
Thanks
PATCH 1/1 imx: fix pico-dwarf-imx6ul and pico-dwarf-imx7d build issues
Hi Fabio, Stefano,
On Sat, 14 Sep 2019 09:18:22 -0300
Fabio Estevam festevam at gmail.com wrote:
...
Quoted 4 lines
Quoted 2 lines
configs/pico-dwarf-imx6ul_defconfig | 2 +- configs/pico-dwarf-imx7d_defconfig | 2 +-It seems that configs/pico-nymph-imx7d_defconfig conversion is missing.
Yes, somehow I forgot to fix this one. Thanks for paying attention!
Quoted 2 lines
I haven't seen your patch earlier and also sent a fix:
https://lists.denx.de/pipermail/u-boot/2019-September/383582.html
OK, thanks!
--
Anatolij
PATCH 1/1 imx: fix pico-dwarf-imx6ul and pico-dwarf-imx7d build issues
In reply to Fabio EstevamHi Fabio, Anatolji,
thanks both.
Quoted 16 lines · Fabio Estevam
Hi Anatolij,
Quoted 5 lines · Anatolij Gustschin
Fixes:
board/technexion/pico-imx6ul/spl.c: In function 'board_mmc_init':
error: implicit declaration of function 'fsl_esdhc_initialize'Quoted 7 lines
and a simmilar error when building pico-dwarf-imx7d.
Signed-off-by Anatolij Gustschin <[email protected]>Cc Otavio Salvador <[email protected]>--- configs/pico-dwarf-imx6ul_defconfig | 2 +- configs/pico-dwarf-imx7d_defconfig | 2 +-
Quoted 6 lines
It seems that configs/pico-nymph-imx7d_defconfig conversion is missing.
I haven't seen your patch earlier and also sent a fix:
https://lists.denx.de/pipermail/u-boot/2019-September/383582.htmlThanks
Yes, I applied Fabio's and I am letting now Travis running.
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH 1/5 pico-imx6ul: Add DWARF baseboard support
In reply to Stefano BabicOn Sat, Sep 14, 2019 at 8:22 AM Stefano Babic <[email protected]> wrote:
...
Quoted 2 lines
Otavio, I am also fine if you send a follow-up patch to fix it - your decision.
Anatolij sent a fix already. I acked it and copied you.
Signature · 3 lines
Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9 9981-7854 Mobile: +1 (347) 903-9750
PATCH 1/5 pico-imx6ul: Add DWARF baseboard support
Quoted 7 lines · Otavio Salvador
On Sat, Sep 14, 2019 at 8:22 AM Stefano Babic <[email protected]> wrote:
...Quoted 2 lines
Otavio, I am also fine if you send a follow-up patch to fix it - your decision.
Anatolij sent a fix already. I acked it and copied you.
Yes, thanks - I apply it directly on top ofimx tree.
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================