ARM: dts: omap3: Add cpu trips and cooling map for omap3 family
RFC v2 1/2 ARM: dts: omap3: Add cpu trips and cooling map for omap3 family
The OMAP3530, AM3517 and DM3730 all show thresholds of 90C and 105C depending on commercial or industrial temperature ratings. This patch expands the thermal information to the limits of 90 and 105 for alert and critical.
For boards who never use industrial temperatures, these can be changed on their respective device trees with something like:
&cpu_alert0 {
temperature = <85000>; /* millicelsius */
};&cpu_crit {
temperature = <90000>; /* millicelsius */
};---
V2: Change the CPU reference to &cpu instead of &cpu0
arch/arm/boot/dts/omap3-cpu-thermal.dtsi +21 -0
@@ -17,4 +17,25 @@ cpu_thermal: cpu_thermal { /* sensor ID */ thermal-sensors = <&bandgap 0>; + + cpu_trips: trips { + cpu_alert0: cpu_alert { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <105000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cpu_cooling_maps: cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; };
Signature · 1 line
2.17.1
RFC v2 2/2 ARM: omap3: Consolidate thermal references to common omap3
Because the omap34xx, omap36xx and am3517 SoC's have the same thermal junction limits, there is no need to duplicate the entry multiple times.
This patch removes the thermal references from omap36xx and omap34xx and pushes it into the common omap3.dtsi file with the added benefit of enabling the thermal info on the AM3517.
---
V2: Add node name for cpu and add cooling-cells entry
arch/arm/boot/dts/omap3.dtsi +6 -1
@@ -32,7 +32,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu: cpu@0 { compatible = "arm,cortex-a8"; device_type = "cpu"; reg = <0x0>;
@@ -41,9 +41,14 @@ clock-names = "cpu"; clock-latency = <300000>; /* From omap-cpufreq driver */ + #cooling-cells = <2>; }; }; + thermal_zones: thermal-zones { + #include "omap3-cpu-thermal.dtsi" + }; + pmu@54000000 { compatible = "arm,cortex-a8-pmu"; reg = <0x54000000 0x800000>;
arch/arm/boot/dts/omap34xx.dtsi +0 -4
@@ -101,10 +101,6 @@ }; }; }; - - thermal_zones: thermal-zones { - #include "omap3-cpu-thermal.dtsi" - }; }; &ssi {
arch/arm/boot/dts/omap36xx.dtsi +0 -4
@@ -140,10 +140,6 @@ }; }; }; - - thermal_zones: thermal-zones { - #include "omap3-cpu-thermal.dtsi" - }; }; /* OMAP3630 needs dss_96m_fck for VENC */
Signature · 1 line
2.17.1
Re: [RFC v2 2/2] ARM: omap3: Consolidate thermal references to common omap3
Quoted 29 lines
Am 13.09.2019 um 17:37 schrieb Adam Ford <[email protected]>:
Because the omap34xx, omap36xx and am3517 SoC's have the same thermal junction limits, there is no need to duplicate the entry multiple times.
This patch removes the thermal references from omap36xx and omap34xx and pushes it into the common
omap3.dtsifile with the added benefit of enabling the thermal info on the AM3517.Signed-off-by Adam Ford <[email protected]>---
V2: Add node name for cpu and add cooling-cells entryarch/arm/boot/dts/omap3.dtsi +1
-1@@ -32,7 +32,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu: cpu@0 { compatible = "arm,cortex-a8"; device_type = "cpu"; reg = <0x0>;
arch/arm/boot/dts/omap3.dtsi line 46
Quoted 6 lines
arch/arm/boot/dts/omap3.dtsi +1
-0@@ -41,9 +41,14 @@ clock-names = "cpu"; clock-latency = <300000>; /* From omap-cpufreq driver */ + #cooling-cells = <2>; }; };
Looks ok.
arch/arm/boot/dts/omap3.dtsi line 51
Quoted 5 lines
arch/arm/boot/dts/omap3.dtsi +4
-0+ thermal_zones: thermal-zones { + #include "omap3-cpu-thermal.dtsi" + }; +
I have observed one compile issue: we also include this indirectly by am3517.dtsi and the included code refers to <&bandgap 0> but there is no bandgap definition in am3517.dtsi
Therefore I studied the am35x TRM (SPRUGR0C) and compared to the am/dm37x TRM (SPRUGN4M).
But I can't find a bandgap temperature sensor with ADC like it is described in "13.4.6 Band Gap Voltage and Temperature Sensor" for the am/dm37x. Only "BANDGAP Logic" exists in both and both have the CM_FCLKEN3_CORE but with different meaning of bit 0.
There is also no description of an CONTROL_TEMP_SENSOR (0x48002524) register for am35x. (note: the register is also documented for omap3530).
So this might mean that the am35x does not have this feature unless TI simply did not document it because the chip is specified for a single OPP only where it make no sense to monitor the temperature.
We can find out only by looking at 0x48002524 if there is an undocumented bandgap converter.
Which means we probably can't make thermal throttling work for it. And even if the bandgap sensor exists we are lacking an value -> celsius table.
Quoted 23 lines
arch/arm/boot/dts/omap3.dtsi +0
-0pmu@54000000 { compatible = "arm,cortex-a8-pmu"; reg = <0x54000000 0x800000>;arch/arm/boot/dts/omap34xx.dtsi +0
-4@@ -101,10 +101,6 @@ }; }; }; - - thermal_zones: thermal-zones { - #include "omap3-cpu-thermal.dtsi" - }; }; &ssi {arch/arm/boot/dts/omap36xx.dtsi +0
-0
arch/arm/boot/dts/omap36xx.dtsi line 143
Quoted 8 lines
arch/arm/boot/dts/omap36xx.dtsi +0
-4@@ -140,10 +140,6 @@ }; }; }; - - thermal_zones: thermal-zones { - #include "omap3-cpu-thermal.dtsi" - }; };
So if we have to exclude the am3517 we can not apply the rearrangement part of this patch.
I'd suggest to move the cpu: cpu@0 and #cooling-cells into 1/2 (also to make it compile stand-alone). And have the consolidation separately - if we can fix the am3517 bandgap sensor issue.
Quoted 5 lines
arch/arm/boot/dts/omap36xx.dtsi +0
-0/* OMAP3630 needs dss_96m_fck for VENC */Signature · 1 line
2.17.1
Re: [RFC v2 2/2] ARM: omap3: Consolidate thermal references to common omap3
Quoted 8 lines · H. Nikolaus Schaller
Quoted 8 lines
Am 13.09.2019 um 17:37 schrieb Adam Ford <[email protected]>:
Because the omap34xx, omap36xx and am3517 SoC's have the same thermal junction limits, there is no need to duplicate the entry multiple times.
Quoted 5 lines
Quoted 5 lines
This patch removes the thermal references from omap36xx and omap34xx and pushes it into the common
omap3.dtsifile with the added benefit of enabling the thermal info on the AM3517.Signed-off-by Adam Ford <[email protected]>
Disregard this patch. I'll drop it based on Nikolaus' comments below.
Quoted 35 lines
Quoted 17 lines
---
V2: Add node name for cpu and add cooling-cells entryarch/arm/boot/dts/omap3.dtsi +1
-1@@ -32,7 +32,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu: cpu@0 { compatible = "arm,cortex-a8"; device_type = "cpu"; reg = <0x0>;arch/arm/boot/dts/omap3.dtsi line 46
Quoted 6 lines
arch/arm/boot/dts/omap3.dtsi +1
-0@@ -41,9 +41,14 @@ clock-names = "cpu"; clock-latency = <300000>; /* From omap-cpufreq driver */ + #cooling-cells = <2>; }; };Looks ok.
arch/arm/boot/dts/omap3.dtsi line 51
Quoted 5 lines
arch/arm/boot/dts/omap3.dtsi +4
-0+ thermal_zones: thermal-zones { + #include "omap3-cpu-thermal.dtsi" + }; +I have observed one compile issue: we also include this indirectly by
am3517.dtsiand the included code refers to <&bandgap 0> but there is no bandgap definition inam3517.dtsi
Quoted 6 lines
Therefore I studied the am35x TRM (SPRUGR0C) and compared to the am/dm37x TRM (SPRUGN4M).
But I can't find a bandgap temperature sensor with ADC like it is described in "13.4.6 Band Gap Voltage and Temperature Sensor" for the am/dm37x. Only "BANDGAP Logic" exists in both and both have the
CM_FCLKEN3_COREbut with different meaning of bit 0.
I didn't read the technical details, I just read there was a bandgap logic, so I assumed it existed.
Quoted 3 lines
There is also no description of an
CONTROL_TEMP_SENSOR(0x48002524) register for am35x. (note: the register is also documented for omap3530).
Thanks for looking into this.
Quoted 7 lines
So this might mean that the am35x does not have this feature unless TI simply did not document it because the chip is specified for a single OPP only where it make no sense to monitor the temperature.
We can find out only by looking at
0x48002524if there is an undocumented bandgap converter.
I will try to read this register when I have some time, but I have to watch Chelsea FC play in 15 minutes. ;-)
Quoted 3 lines
Which means we probably can't make thermal throttling work for it. And even if the bandgap sensor exists we are lacking an value -> celsius table.
I think it's probably best to abandon this patch, per my comment based on all your comments.
Quoted 37 lines
Quoted 25 lines
arch/arm/boot/dts/omap3.dtsi +0
-0pmu@54000000 { compatible = "arm,cortex-a8-pmu"; reg = <0x54000000 0x800000>;arch/arm/boot/dts/omap34xx.dtsi +0
-4@@ -101,10 +101,6 @@ }; }; }; - - thermal_zones: thermal-zones { - #include "omap3-cpu-thermal.dtsi" - }; }; &ssi {arch/arm/boot/dts/omap36xx.dtsi +0
-0arch/arm/boot/dts/omap36xx.dtsi line 143
Quoted 8 lines
arch/arm/boot/dts/omap36xx.dtsi +0
-4@@ -140,10 +140,6 @@ }; }; }; - - thermal_zones: thermal-zones { - #include "omap3-cpu-thermal.dtsi" - }; };So if we have to exclude the am3517 we can not apply the rearrangement part of this patch.
Quoted 3 lines
I'd suggest to move the cpu: cpu@0 and #cooling-cells into 1/2 (also to make it compile stand-alone). And have the consolidation separately - if we can fix the am3517 bandgap sensor issue.
I'll drop this, and leave everything in the omap3-cpu-thermal file and let omap34xx and omap36xx point to them as we do now.
Quoted 9 lines
Quoted 6 lines
arch/arm/boot/dts/omap36xx.dtsi +0
-1/* OMAP3630 needs dss_96m_fck for VENC */ --2.17.1
Quoted 56 lines
Am 13.09.2019 um 17:37 schrieb Adam Ford <[email protected]>:
The OMAP3530, AM3517 and DM3730 all show thresholds of 90C and 105C depending on commercial or industrial temperature ratings. This patch expands the thermal information to the limits of 90 and 105 for alert and critical.
For boards who never use industrial temperatures, these can be changed on their respective device trees with something like:
&cpu_alert0 { temperature = <85000>; /* millicelsius */ };&cpu_crit { temperature = <90000>; /* millicelsius */ };Signed-off-by Adam Ford <[email protected]>---
V2: Change the CPU reference to &cpu instead of &cpu0arch/arm/boot/dts/omap3-cpu-thermal.dtsi +21
-0@@ -17,4 +17,25 @@ cpu_thermal: cpu_thermal { /* sensor ID */ thermal-sensors = <&bandgap 0>; + + cpu_trips: trips { + cpu_alert0: cpu_alert { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <105000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cpu_cooling_maps: cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; };Signature · 1 line
2.17.1
Here is my test log (GTA04A5 with DM3730CBP100). "high-load" script is driving the NEON to full power and would report calculation errors.
There is no noise visible in the bandgap sensor data induced by power supply fluctuations (log shows system voltage while charging).
root@letux:~# ./high-load -n2 100% load stress test for 1 cores running ./neon_loop2 Sat Sep 14 09:05:50 UTC 2019 65° 4111mV 1000MHz Sat Sep 14 09:05:50 UTC 2019 67° 4005mV 1000MHz Sat Sep 14 09:05:52 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:53 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:55 UTC 2019 72° 3976mV 1000MHz Sat Sep 14 09:05:56 UTC 2019 72° 4023mV 1000MHz Sat Sep 14 09:05:57 UTC 2019 72° 3900mV 1000MHz Sat Sep 14 09:05:59 UTC 2019 73° 4029mV 1000MHz Sat Sep 14 09:06:00 UTC 2019 73° 3988mV 1000MHz Sat Sep 14 09:06:01 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:03 UTC 2019 73° 4011mV 1000MHz Sat Sep 14 09:06:04 UTC 2019 73° 4117mV 1000MHz Sat Sep 14 09:06:06 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:07 UTC 2019 75° 3994mV 1000MHz Sat Sep 14 09:06:08 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:09 UTC 2019 75° 4046mV 1000MHz Sat Sep 14 09:06:11 UTC 2019 75° 4005mV 1000MHz Sat Sep 14 09:06:12 UTC 2019 75° 4023mV 1000MHz Sat Sep 14 09:06:14 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:15 UTC 2019 75° 4011mV 1000MHz Sat Sep 14 09:06:16 UTC 2019 77° 4017mV 1000MHz Sat Sep 14 09:06:18 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:19 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:20 UTC 2019 77° 3988mV 1000MHz Sat Sep 14 09:06:22 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:23 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:24 UTC 2019 78° 4005mV 1000MHz Sat Sep 14 09:06:26 UTC 2019 78° 4105mV 1000MHz Sat Sep 14 09:06:27 UTC 2019 78° 4011mV 1000MHz Sat Sep 14 09:06:28 UTC 2019 78° 3994mV 1000MHz Sat Sep 14 09:06:30 UTC 2019 78° 4123mV 1000MHz ... Sat Sep 14 09:09:57 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:09:59 UTC 2019 88° 4164mV 1000MHz Sat Sep 14 09:10:00 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:01 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:03 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:10:04 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:06 UTC 2019 88° 4146mV 1000MHz Sat Sep 14 09:10:07 UTC 2019 88° 4041mV 1000MHz Sat Sep 14 09:10:08 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:10 UTC 2019 88° 4052mV 1000MHz Sat Sep 14 09:10:11 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:12 UTC 2019 88° 4152mV 1000MHz Sat Sep 14 09:10:14 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:15 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:17 UTC 2019 88° 4170mV 1000MHz Sat Sep 14 09:10:18 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:19 UTC 2019 88° 4187mV 1000MHz Sat Sep 14 09:10:21 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:22 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:23 UTC 2019 90° 4070mV 1000MHz Sat Sep 14 09:10:25 UTC 2019 88° 4123mV 800MHz Sat Sep 14 09:10:26 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:28 UTC 2019 90° 4058mV 1000MHz Sat Sep 14 09:10:29 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:30 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:32 UTC 2019 88° 4117mV 1000MHz Sat Sep 14 09:10:33 UTC 2019 88° 4105mV 800MHz Sat Sep 14 09:10:34 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:36 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:37 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:39 UTC 2019 88° 4017mV 1000MHz Sat Sep 14 09:10:40 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:41 UTC 2019 88° 4058mV 800MHz Sat Sep 14 09:10:42 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:44 UTC 2019 90° 4058mV 1000MHz Sat Sep 14 09:10:45 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:47 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:48 UTC 2019 88° 4029mV 1000MHz Sat Sep 14 09:10:50 UTC 2019 90° 4046mV 1000MHz ^Ckill 4680 root@letux:~# cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 CPUs which need to have their frequency coordinated by software: 0 maximum transition latency: 300 us. hardware limits: 300 MHz - 1000 MHz available frequency steps: 300 MHz, 600 MHz, 800 MHz, 1000 MHz available cpufreq governors: conservative, userspace, powersave, ondemand, performance current policy: frequency should be within 300 MHz and 1000 MHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency is 600 MHz (asserted by call to hardware). cpufreq stats: 300 MHz:22.81%, 600 MHz:2.50%, 800 MHz:2.10%, 1000 MHz:72.59% (1563) root@letux:~#
So OPP is reduced if bandgap sensor reports >= 90°C which almost immediately makes the temperature go down.
No operational hickups were observed.
Surface temperature of the PoP chip did rise to approx. 53°C during this test.
Quoted 62 lines · H. Nikolaus Schaller
Quoted 55 lines
Am 13.09.2019 um 17:37 schrieb Adam Ford <[email protected]>:
The OMAP3530, AM3517 and DM3730 all show thresholds of 90C and 105C depending on commercial or industrial temperature ratings. This patch expands the thermal information to the limits of 90 and 105 for alert and critical.
For boards who never use industrial temperatures, these can be changed on their respective device trees with something like:
&cpu_alert0 { temperature = <85000>; /* millicelsius */ };&cpu_crit { temperature = <90000>; /* millicelsius */ };Signed-off-by Adam Ford <[email protected]>---
V2: Change the CPU reference to &cpu instead of &cpu0arch/arm/boot/dts/omap3-cpu-thermal.dtsi +21
-1@@ -17,4 +17,25 @@ cpu_thermal: cpu_thermal { /* sensor ID */ thermal-sensors = <&bandgap 0>; + + cpu_trips: trips { + cpu_alert0: cpu_alert { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <105000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cpu_cooling_maps: cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; --Quoted 2 lines
2.17.1
Here is my test log (GTA04A5 with DM3730CBP100). "high-load" script is driving the NEON to full power and would report calculation errors.
Quoted 4 lines
There is no noise visible in the bandgap sensor data induced by power supply fluctuations (log shows system voltage while charging).
Great data!
Quoted 46 lines
root@letux:~# ./high-load -n2 100% load stress test for 1 cores running ./neon_loop2 Sat Sep 14 09:05:50 UTC 2019 65° 4111mV 1000MHz Sat Sep 14 09:05:50 UTC 2019 67° 4005mV 1000MHz Sat Sep 14 09:05:52 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:53 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:55 UTC 2019 72° 3976mV 1000MHz Sat Sep 14 09:05:56 UTC 2019 72° 4023mV 1000MHz Sat Sep 14 09:05:57 UTC 2019 72° 3900mV 1000MHz Sat Sep 14 09:05:59 UTC 2019 73° 4029mV 1000MHz Sat Sep 14 09:06:00 UTC 2019 73° 3988mV 1000MHz Sat Sep 14 09:06:01 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:03 UTC 2019 73° 4011mV 1000MHz Sat Sep 14 09:06:04 UTC 2019 73° 4117mV 1000MHz Sat Sep 14 09:06:06 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:07 UTC 2019 75° 3994mV 1000MHz Sat Sep 14 09:06:08 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:09 UTC 2019 75° 4046mV 1000MHz Sat Sep 14 09:06:11 UTC 2019 75° 4005mV 1000MHz Sat Sep 14 09:06:12 UTC 2019 75° 4023mV 1000MHz Sat Sep 14 09:06:14 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:15 UTC 2019 75° 4011mV 1000MHz Sat Sep 14 09:06:16 UTC 2019 77° 4017mV 1000MHz Sat Sep 14 09:06:18 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:19 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:20 UTC 2019 77° 3988mV 1000MHz Sat Sep 14 09:06:22 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:23 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:24 UTC 2019 78° 4005mV 1000MHz Sat Sep 14 09:06:26 UTC 2019 78° 4105mV 1000MHz Sat Sep 14 09:06:27 UTC 2019 78° 4011mV 1000MHz Sat Sep 14 09:06:28 UTC 2019 78° 3994mV 1000MHz Sat Sep 14 09:06:30 UTC 2019 78° 4123mV 1000MHz ... Sat Sep 14 09:09:57 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:09:59 UTC 2019 88° 4164mV 1000MHz Sat Sep 14 09:10:00 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:01 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:03 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:10:04 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:06 UTC 2019 88° 4146mV 1000MHz Sat Sep 14 09:10:07 UTC 2019 88° 4041mV 1000MHz Sat Sep 14 09:10:08 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:10 UTC 2019 88° 4052mV 1000MHz Sat Sep 14 09:10:11 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:12 UTC 2019 88° 4152mV 1000MHz
Quoted 8 lines
Sat Sep 14 09:10:14 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:15 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:17 UTC 2019 88° 4170mV 1000MHz Sat Sep 14 09:10:18 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:19 UTC 2019 88° 4187mV 1000MHz Sat Sep 14 09:10:21 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:22 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:23 UTC 2019 90° 4070mV 1000MHz
Should we be a little more conservative? Without knowing the accuracy, i believe we do not want to run at 800 or 1GHz at 90C, so if we made this value 89 instead of 90, we would throttle a little more conservatively.
Quoted 3 lines
Sat Sep 14 09:10:25 UTC 2019 88° 4123mV 800MHz Sat Sep 14 09:10:26 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:28 UTC 2019 90° 4058mV 1000MHz
Again here, I interpret the data sheet correctly, we're technically out of spec
Quoted 46 lines
Sat Sep 14 09:10:29 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:30 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:32 UTC 2019 88° 4117mV 1000MHz Sat Sep 14 09:10:33 UTC 2019 88° 4105mV 800MHz Sat Sep 14 09:10:34 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:36 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:37 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:39 UTC 2019 88° 4017mV 1000MHz Sat Sep 14 09:10:40 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:41 UTC 2019 88° 4058mV 800MHz Sat Sep 14 09:10:42 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:44 UTC 2019 90° 4058mV 1000MHz Sat Sep 14 09:10:45 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:47 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:48 UTC 2019 88° 4029mV 1000MHz Sat Sep 14 09:10:50 UTC 2019 90° 4046mV 1000MHz ^Ckill 4680
root@letux:~# cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 CPUs which need to have their frequency coordinated by software: 0 maximum transition latency: 300 us. hardware limits: 300 MHz - 1000 MHz available frequency steps: 300 MHz, 600 MHz, 800 MHz, 1000 MHz available cpufreq governors: conservative, userspace, powersave, ondemand, performance current policy: frequency should be within 300 MHz and 1000 MHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency is 600 MHz (asserted by call to hardware). cpufreq stats: 300 MHz:22.81%, 600 MHz:2.50%, 800 MHz:2.10%, 1000 MHz:72.59% (1563) root@letux:~#So OPP is reduced if bandgap sensor reports >= 90°C which almost immediately makes the temperature go down.
No operational hickups were observed.
Surface temperature of the PoP chip did rise to approx. 53°C during this test.
Quoted 128 lines
Am 14.09.2019 um 15:42 schrieb Adam Ford <[email protected]>:
Quoted 62 lines · H. Nikolaus Schaller
Quoted 55 lines
Am 13.09.2019 um 17:37 schrieb Adam Ford <[email protected]>:
The OMAP3530, AM3517 and DM3730 all show thresholds of 90C and 105C depending on commercial or industrial temperature ratings. This patch expands the thermal information to the limits of 90 and 105 for alert and critical.
For boards who never use industrial temperatures, these can be changed on their respective device trees with something like:
&cpu_alert0 { temperature = <85000>; /* millicelsius */ };&cpu_crit { temperature = <90000>; /* millicelsius */ };Signed-off-by Adam Ford <[email protected]>---
V2: Change the CPU reference to &cpu instead of &cpu0arch/arm/boot/dts/omap3-cpu-thermal.dtsi +21
-1@@ -17,4 +17,25 @@ cpu_thermal: cpu_thermal { /* sensor ID */ thermal-sensors = <&bandgap 0>; + + cpu_trips: trips { + cpu_alert0: cpu_alert { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <105000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cpu_cooling_maps: cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; --Quoted 2 lines
2.17.1
Here is my test log (GTA04A5 with DM3730CBP100). "high-load" script is driving the NEON to full power and would report calculation errors.
Quoted 4 lines
There is no noise visible in the bandgap sensor data induced by power supply fluctuations (log shows system voltage while charging).
Great data!
Quoted 46 lines
root@letux:~# ./high-load -n2 100% load stress test for 1 cores running ./neon_loop2 Sat Sep 14 09:05:50 UTC 2019 65° 4111mV 1000MHz Sat Sep 14 09:05:50 UTC 2019 67° 4005mV 1000MHz Sat Sep 14 09:05:52 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:53 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:55 UTC 2019 72° 3976mV 1000MHz Sat Sep 14 09:05:56 UTC 2019 72° 4023mV 1000MHz Sat Sep 14 09:05:57 UTC 2019 72° 3900mV 1000MHz Sat Sep 14 09:05:59 UTC 2019 73° 4029mV 1000MHz Sat Sep 14 09:06:00 UTC 2019 73° 3988mV 1000MHz Sat Sep 14 09:06:01 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:03 UTC 2019 73° 4011mV 1000MHz Sat Sep 14 09:06:04 UTC 2019 73° 4117mV 1000MHz Sat Sep 14 09:06:06 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:07 UTC 2019 75° 3994mV 1000MHz Sat Sep 14 09:06:08 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:09 UTC 2019 75° 4046mV 1000MHz Sat Sep 14 09:06:11 UTC 2019 75° 4005mV 1000MHz Sat Sep 14 09:06:12 UTC 2019 75° 4023mV 1000MHz Sat Sep 14 09:06:14 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:15 UTC 2019 75° 4011mV 1000MHz Sat Sep 14 09:06:16 UTC 2019 77° 4017mV 1000MHz Sat Sep 14 09:06:18 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:19 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:20 UTC 2019 77° 3988mV 1000MHz Sat Sep 14 09:06:22 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:23 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:24 UTC 2019 78° 4005mV 1000MHz Sat Sep 14 09:06:26 UTC 2019 78° 4105mV 1000MHz Sat Sep 14 09:06:27 UTC 2019 78° 4011mV 1000MHz Sat Sep 14 09:06:28 UTC 2019 78° 3994mV 1000MHz Sat Sep 14 09:06:30 UTC 2019 78° 4123mV 1000MHz ... Sat Sep 14 09:09:57 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:09:59 UTC 2019 88° 4164mV 1000MHz Sat Sep 14 09:10:00 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:01 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:03 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:10:04 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:06 UTC 2019 88° 4146mV 1000MHz Sat Sep 14 09:10:07 UTC 2019 88° 4041mV 1000MHz Sat Sep 14 09:10:08 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:10 UTC 2019 88° 4052mV 1000MHz Sat Sep 14 09:10:11 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:12 UTC 2019 88° 4152mV 1000MHzQuoted 8 lines
Sat Sep 14 09:10:14 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:15 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:17 UTC 2019 88° 4170mV 1000MHz Sat Sep 14 09:10:18 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:19 UTC 2019 88° 4187mV 1000MHz Sat Sep 14 09:10:21 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:22 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:23 UTC 2019 90° 4070mV 1000MHz
Quoted 4 lines
Should we be a little more conservative? Without knowing the accuracy, i believe we do not want to run at 800 or 1GHz at 90C, so if we made this value 89 instead of 90, we would throttle a little more conservatively.
Well, the OMAP5 also defines exactly 100°C in the device tree.
I would assume that the badgap sensor accuracy is so that it never reports less than the real temperature. So if we throttle at reported 90° TJ is likely lower.
Quoted 5 lines
Quoted 3 lines
Sat Sep 14 09:10:25 UTC 2019 88° 4123mV 800MHz Sat Sep 14 09:10:26 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:28 UTC 2019 90° 4058mV 1000MHz
Again here, I interpret the data sheet correctly, we're technically out of spec
I read the data sheet as if 90°C at OPP1G is still within spec. 91 would be obviously outside (if bandgap sensor is precise).
Quoted 40 lines
Quoted 40 lines
Sat Sep 14 09:10:29 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:30 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:32 UTC 2019 88° 4117mV 1000MHz Sat Sep 14 09:10:33 UTC 2019 88° 4105mV 800MHz Sat Sep 14 09:10:34 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:36 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:37 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:39 UTC 2019 88° 4017mV 1000MHz Sat Sep 14 09:10:40 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:41 UTC 2019 88° 4058mV 800MHz Sat Sep 14 09:10:42 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:44 UTC 2019 90° 4058mV 1000MHz Sat Sep 14 09:10:45 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:47 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:48 UTC 2019 88° 4029mV 1000MHz Sat Sep 14 09:10:50 UTC 2019 90° 4046mV 1000MHz ^Ckill 4680
root@letux:~# cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 CPUs which need to have their frequency coordinated by software: 0 maximum transition latency: 300 us. hardware limits: 300 MHz - 1000 MHz available frequency steps: 300 MHz, 600 MHz, 800 MHz, 1000 MHz available cpufreq governors: conservative, userspace, powersave, ondemand, performance current policy: frequency should be within 300 MHz and 1000 MHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency is 600 MHz (asserted by call to hardware). cpufreq stats: 300 MHz:22.81%, 600 MHz:2.50%, 800 MHz:2.10%, 1000 MHz:72.59% (1563) root@letux:~#So OPP is reduced if bandgap sensor reports >= 90°C which almost immediately makes the temperature go down.
Quoted 7 lines
Quoted 7 lines
No operational hickups were observed.
Surface temperature of the PoP chip did rise to approx. 53°C during this test.
BTW: this patch (set) is even independent of my 1GHz OPP patches. Should also work with OPP-v1 definitions so that maintainers can decide which one to apply first.
It is just more difficult to reach TJ of 90°C without 1GHz.
BR,
Nikolaus
Quoted 194 lines · H. Nikolaus Schaller
Quoted 129 lines
Am 14.09.2019 um 15:42 schrieb Adam Ford <[email protected]>:
Quoted 62 lines · H. Nikolaus Schaller
Quoted 55 lines
Am 13.09.2019 um 17:37 schrieb Adam Ford <[email protected]>:
The OMAP3530, AM3517 and DM3730 all show thresholds of 90C and 105C depending on commercial or industrial temperature ratings. This patch expands the thermal information to the limits of 90 and 105 for alert and critical.
For boards who never use industrial temperatures, these can be changed on their respective device trees with something like:
&cpu_alert0 { temperature = <85000>; /* millicelsius */ };&cpu_crit { temperature = <90000>; /* millicelsius */ };Signed-off-by Adam Ford <[email protected]>---
V2: Change the CPU reference to &cpu instead of &cpu0arch/arm/boot/dts/omap3-cpu-thermal.dtsi +21
-1@@ -17,4 +17,25 @@ cpu_thermal: cpu_thermal { /* sensor ID */ thermal-sensors = <&bandgap 0>; + + cpu_trips: trips { + cpu_alert0: cpu_alert { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <105000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cpu_cooling_maps: cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; --Quoted 2 lines
2.17.1
Here is my test log (GTA04A5 with DM3730CBP100). "high-load" script is driving the NEON to full power and would report calculation errors.
Quoted 4 lines
There is no noise visible in the bandgap sensor data induced by power supply fluctuations (log shows system voltage while charging).
Great data!
Quoted 46 lines
root@letux:~# ./high-load -n2 100% load stress test for 1 cores running ./neon_loop2 Sat Sep 14 09:05:50 UTC 2019 65° 4111mV 1000MHz Sat Sep 14 09:05:50 UTC 2019 67° 4005mV 1000MHz Sat Sep 14 09:05:52 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:53 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:55 UTC 2019 72° 3976mV 1000MHz Sat Sep 14 09:05:56 UTC 2019 72° 4023mV 1000MHz Sat Sep 14 09:05:57 UTC 2019 72° 3900mV 1000MHz Sat Sep 14 09:05:59 UTC 2019 73° 4029mV 1000MHz Sat Sep 14 09:06:00 UTC 2019 73° 3988mV 1000MHz Sat Sep 14 09:06:01 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:03 UTC 2019 73° 4011mV 1000MHz Sat Sep 14 09:06:04 UTC 2019 73° 4117mV 1000MHz Sat Sep 14 09:06:06 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:07 UTC 2019 75° 3994mV 1000MHz Sat Sep 14 09:06:08 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:09 UTC 2019 75° 4046mV 1000MHz Sat Sep 14 09:06:11 UTC 2019 75° 4005mV 1000MHz Sat Sep 14 09:06:12 UTC 2019 75° 4023mV 1000MHz Sat Sep 14 09:06:14 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:15 UTC 2019 75° 4011mV 1000MHz Sat Sep 14 09:06:16 UTC 2019 77° 4017mV 1000MHz Sat Sep 14 09:06:18 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:19 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:20 UTC 2019 77° 3988mV 1000MHz Sat Sep 14 09:06:22 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:23 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:24 UTC 2019 78° 4005mV 1000MHz Sat Sep 14 09:06:26 UTC 2019 78° 4105mV 1000MHz Sat Sep 14 09:06:27 UTC 2019 78° 4011mV 1000MHz Sat Sep 14 09:06:28 UTC 2019 78° 3994mV 1000MHz Sat Sep 14 09:06:30 UTC 2019 78° 4123mV 1000MHz ... Sat Sep 14 09:09:57 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:09:59 UTC 2019 88° 4164mV 1000MHz Sat Sep 14 09:10:00 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:01 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:03 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:10:04 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:06 UTC 2019 88° 4146mV 1000MHz Sat Sep 14 09:10:07 UTC 2019 88° 4041mV 1000MHz Sat Sep 14 09:10:08 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:10 UTC 2019 88° 4052mV 1000MHz Sat Sep 14 09:10:11 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:12 UTC 2019 88° 4152mV 1000MHzQuoted 8 lines
Sat Sep 14 09:10:14 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:15 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:17 UTC 2019 88° 4170mV 1000MHz Sat Sep 14 09:10:18 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:19 UTC 2019 88° 4187mV 1000MHz Sat Sep 14 09:10:21 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:22 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:23 UTC 2019 90° 4070mV 1000MHzQuoted 4 lines
Should we be a little more conservative? Without knowing the accuracy, i believe we do not want to run at 800 or 1GHz at 90C, so if we made this value 89 instead of 90, we would throttle a little more conservatively.
Well, the OMAP5 also defines exactly 100°C in the device tree.
I would assume that the badgap sensor accuracy is so that it never reports less than the real temperature. So if we throttle at reported 90° TJ is likely lower.
Quoted 5 lines
Quoted 3 lines
Sat Sep 14 09:10:25 UTC 2019 88° 4123mV 800MHz Sat Sep 14 09:10:26 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:28 UTC 2019 90° 4058mV 1000MHz
Again here, I interpret the data sheet correctly, we're technically out of spec
I read the data sheet as if 90°C at OPP1G is still within spec. 91 would be obviously outside (if bandgap sensor is precise).
Quoted 45 lines
Quoted 45 lines
Sat Sep 14 09:10:29 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:30 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:32 UTC 2019 88° 4117mV 1000MHz Sat Sep 14 09:10:33 UTC 2019 88° 4105mV 800MHz Sat Sep 14 09:10:34 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:36 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:37 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:39 UTC 2019 88° 4017mV 1000MHz Sat Sep 14 09:10:40 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:41 UTC 2019 88° 4058mV 800MHz Sat Sep 14 09:10:42 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:44 UTC 2019 90° 4058mV 1000MHz Sat Sep 14 09:10:45 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:47 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:48 UTC 2019 88° 4029mV 1000MHz Sat Sep 14 09:10:50 UTC 2019 90° 4046mV 1000MHz ^Ckill 4680
root@letux:~# cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 CPUs which need to have their frequency coordinated by software: 0 maximum transition latency: 300 us. hardware limits: 300 MHz - 1000 MHz available frequency steps: 300 MHz, 600 MHz, 800 MHz, 1000 MHz available cpufreq governors: conservative, userspace, powersave, ondemand, performance current policy: frequency should be within 300 MHz and 1000 MHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency is 600 MHz (asserted by call to hardware). cpufreq stats: 300 MHz:22.81%, 600 MHz:2.50%, 800 MHz:2.10%, 1000 MHz:72.59% (1563) root@letux:~#So OPP is reduced if bandgap sensor reports >= 90°C which almost immediately makes the temperature go down.
No operational hickups were observed.
Surface temperature of the PoP chip did rise to approx. 53°C during this test.
Quoted 6 lines
Quoted 2 lines
Quoted 2 lines
BTW: this patch (set) is even independent of my 1GHz OPP patches. Should also work with OPP-v1 definitions so that maintainers can decide which one to apply first.
If I am going integrate the cooling references into &cpu node, I'll probably base it on your work since the cooling isn't really that important until we exceed 800MHz. If I do it on the current linux master or omap for-next branch, it may not apply cleanly.
Quoted 2 lines
It is just more difficult to reach TJ of 90°C without 1GHz.
If it even does at all without external influences.
adam
Quoted 4 lines
BR,
Nikolaus
Quoted 9 lines · Adam Ford
Quoted 7 lines · H. Nikolaus Schaller
Quoted 7 lines
Am 14.09.2019 um 15:42 schrieb Adam Ford <[email protected]>:
Quoted 2 lines · H. Nikolaus Schaller
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Am 13.09.2019 um 17:37 schrieb Adam Ford <[email protected]>:
The OMAP3530, AM3517 and DM3730 all show thresholds of 90C and 105C depending on commercial or industrial temperature ratings. This patch expands the thermal information to the limits of 90 and 105 for alert and critical.
Tom / anyone from TI,
I am going to rebase this patch from the current 5.4-RC branch, remove the AM3517 references, and leave the throttling only applicable to omap34xx and 36xx (like it is now), and remove the RFC. Before I do that, I was hoping for some feedback on whether or not there is a reason to not do this while acknowledging the thermal sensor isn't very accurate.
Does anyone have any objections to this?
Other than the omap mailing list, are there other lists that should be CC'd?
adam
Quoted 202 lines
Quoted 180 lines
Quoted 115 lines
Quoted 53 lines
Quoted 46 lines
For boards who never use industrial temperatures, these can be changed on their respective device trees with something like:
&cpu_alert0 { temperature = <85000>; /* millicelsius */ };&cpu_crit { temperature = <90000>; /* millicelsius */ };Signed-off-by Adam Ford <[email protected]>---
V2: Change the CPU reference to &cpu instead of &cpu0arch/arm/boot/dts/omap3-cpu-thermal.dtsi +21
-1@@ -17,4 +17,25 @@ cpu_thermal: cpu_thermal { /* sensor ID */ thermal-sensors = <&bandgap 0>; + + cpu_trips: trips { + cpu_alert0: cpu_alert { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <105000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cpu_cooling_maps: cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; --Quoted 2 lines
2.17.1
Here is my test log (GTA04A5 with DM3730CBP100). "high-load" script is driving the NEON to full power and would report calculation errors.
Quoted 4 lines
There is no noise visible in the bandgap sensor data induced by power supply fluctuations (log shows system voltage while charging).
Great data!
Quoted 46 lines
root@letux:~# ./high-load -n2 100% load stress test for 1 cores running ./neon_loop2 Sat Sep 14 09:05:50 UTC 2019 65° 4111mV 1000MHz Sat Sep 14 09:05:50 UTC 2019 67° 4005mV 1000MHz Sat Sep 14 09:05:52 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:53 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:55 UTC 2019 72° 3976mV 1000MHz Sat Sep 14 09:05:56 UTC 2019 72° 4023mV 1000MHz Sat Sep 14 09:05:57 UTC 2019 72° 3900mV 1000MHz Sat Sep 14 09:05:59 UTC 2019 73° 4029mV 1000MHz Sat Sep 14 09:06:00 UTC 2019 73° 3988mV 1000MHz Sat Sep 14 09:06:01 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:03 UTC 2019 73° 4011mV 1000MHz Sat Sep 14 09:06:04 UTC 2019 73° 4117mV 1000MHz Sat Sep 14 09:06:06 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:07 UTC 2019 75° 3994mV 1000MHz Sat Sep 14 09:06:08 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:09 UTC 2019 75° 4046mV 1000MHz Sat Sep 14 09:06:11 UTC 2019 75° 4005mV 1000MHz Sat Sep 14 09:06:12 UTC 2019 75° 4023mV 1000MHz Sat Sep 14 09:06:14 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:15 UTC 2019 75° 4011mV 1000MHz Sat Sep 14 09:06:16 UTC 2019 77° 4017mV 1000MHz Sat Sep 14 09:06:18 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:19 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:20 UTC 2019 77° 3988mV 1000MHz Sat Sep 14 09:06:22 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:23 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:24 UTC 2019 78° 4005mV 1000MHz Sat Sep 14 09:06:26 UTC 2019 78° 4105mV 1000MHz Sat Sep 14 09:06:27 UTC 2019 78° 4011mV 1000MHz Sat Sep 14 09:06:28 UTC 2019 78° 3994mV 1000MHz Sat Sep 14 09:06:30 UTC 2019 78° 4123mV 1000MHz ... Sat Sep 14 09:09:57 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:09:59 UTC 2019 88° 4164mV 1000MHz Sat Sep 14 09:10:00 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:01 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:03 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:10:04 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:06 UTC 2019 88° 4146mV 1000MHz Sat Sep 14 09:10:07 UTC 2019 88° 4041mV 1000MHz Sat Sep 14 09:10:08 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:10 UTC 2019 88° 4052mV 1000MHz Sat Sep 14 09:10:11 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:12 UTC 2019 88° 4152mV 1000MHzQuoted 8 lines
Sat Sep 14 09:10:14 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:15 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:17 UTC 2019 88° 4170mV 1000MHz Sat Sep 14 09:10:18 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:19 UTC 2019 88° 4187mV 1000MHz Sat Sep 14 09:10:21 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:22 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:23 UTC 2019 90° 4070mV 1000MHzQuoted 4 lines
Should we be a little more conservative? Without knowing the accuracy, i believe we do not want to run at 800 or 1GHz at 90C, so if we made this value 89 instead of 90, we would throttle a little more conservatively.
Well, the OMAP5 also defines exactly 100°C in the device tree.
I would assume that the badgap sensor accuracy is so that it never reports less than the real temperature. So if we throttle at reported 90° TJ is likely lower.
Quoted 5 lines
Quoted 3 lines
Sat Sep 14 09:10:25 UTC 2019 88° 4123mV 800MHz Sat Sep 14 09:10:26 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:28 UTC 2019 90° 4058mV 1000MHz
Again here, I interpret the data sheet correctly, we're technically out of spec
I read the data sheet as if 90°C at OPP1G is still within spec. 91 would be obviously outside (if bandgap sensor is precise).
Quoted 45 lines
Quoted 45 lines
Sat Sep 14 09:10:29 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:30 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:32 UTC 2019 88° 4117mV 1000MHz Sat Sep 14 09:10:33 UTC 2019 88° 4105mV 800MHz Sat Sep 14 09:10:34 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:36 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:37 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:39 UTC 2019 88° 4017mV 1000MHz Sat Sep 14 09:10:40 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:41 UTC 2019 88° 4058mV 800MHz Sat Sep 14 09:10:42 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:44 UTC 2019 90° 4058mV 1000MHz Sat Sep 14 09:10:45 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:47 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:48 UTC 2019 88° 4029mV 1000MHz Sat Sep 14 09:10:50 UTC 2019 90° 4046mV 1000MHz ^Ckill 4680
root@letux:~# cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 CPUs which need to have their frequency coordinated by software: 0 maximum transition latency: 300 us. hardware limits: 300 MHz - 1000 MHz available frequency steps: 300 MHz, 600 MHz, 800 MHz, 1000 MHz available cpufreq governors: conservative, userspace, powersave, ondemand, performance current policy: frequency should be within 300 MHz and 1000 MHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency is 600 MHz (asserted by call to hardware). cpufreq stats: 300 MHz:22.81%, 600 MHz:2.50%, 800 MHz:2.10%, 1000 MHz:72.59% (1563) root@letux:~#So OPP is reduced if bandgap sensor reports >= 90°C which almost immediately makes the temperature go down.
No operational hickups were observed.
Surface temperature of the PoP chip did rise to approx. 53°C during this test.
Quoted 6 lines
Quoted 2 lines
Quoted 2 lines
BTW: this patch (set) is even independent of my 1GHz OPP patches. Should also work with OPP-v1 definitions so that maintainers can decide which one to apply first.
If I am going integrate the cooling references into &cpu node, I'll probably base it on your work since the cooling isn't really that important until we exceed 800MHz. If I do it on the current linux master or omap for-next branch, it may not apply cleanly.
Quoted 2 lines
It is just more difficult to reach TJ of 90°C without 1GHz.
If it even does at all without external influences.
adam
Quoted 4 lines
BR,
Nikolaus
Quoted 21 lines
Am 07.10.2019 um 17:11 schrieb Adam Ford <[email protected]>:
Quoted 9 lines · Adam Ford
Quoted 7 lines · H. Nikolaus Schaller
Quoted 7 lines
Am 14.09.2019 um 15:42 schrieb Adam Ford <[email protected]>:
Quoted 2 lines · H. Nikolaus Schaller
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Am 13.09.2019 um 17:37 schrieb Adam Ford <[email protected]>:
The OMAP3530, AM3517 and DM3730 all show thresholds of 90C and 105C depending on commercial or industrial temperature ratings. This patch expands the thermal information to the limits of 90 and 105 for alert and critical.
Quoted 8 lines
Tom / anyone from TI,
I am going to rebase this patch from the current 5.4-RC branch, remove the AM3517 references, and leave the throttling only applicable to omap34xx and 36xx (like it is now), and remove the RFC. Before I do that, I was hoping for some feedback on whether or not there is a reason to not do this while acknowledging the thermal sensor isn't very accurate.
I wonder if there is a more precise definition what "isn't very accurate" means?
Is it just because the TI_BANDGAP_FEATURE_UNRELIABLE bit is set in the driver and we assume that it is right?
Of course the "junction temperature" (TJ) is not well defined (at which edge? in which area?) and the bandgap sensor can only report a single point of the die. So e.g. the GPU or the NEON unit may be hotter or cooler.
And, the bandgap sensor + ADC is unlikely to be well calibrated to 0.1°C precision.
But in my experiments there seems to be not much noise and values rise or fall monotonic according to expectations of processor load.
So a report of 90°C may not be exactly 90°C and some parts of the SoC may be hotter.
I would also assume that the TJ limits of 90°C have some safety margin but there seems to be no information in the data sheet.
So, IMHO an "unreliable" bandgap sensor is better than no sensor and no trips / cooling maps.
One more thing is with the omap3 bandgap sensor (driver?). It appears to report the value of the previous measurement. So unless it is regularily polled (like cpufreq seems to do) it will report outdated values. The first read hours after boot may report the value during probe while booting.
This is also a source of missing accuracy of course. But I haven't investigated this (can only be tested if thermal management is turned off) because I think it has no practical influence if cpufreq is polling.
Quoted 209 lines
Does anyone have any objections to this?
Other than the omap mailing list, are there other lists that should be CC'd?
adam
Quoted 202 lines
Quoted 180 lines
Quoted 115 lines
Quoted 53 lines
Quoted 46 lines
For boards who never use industrial temperatures, these can be changed on their respective device trees with something like:
&cpu_alert0 { temperature = <85000>; /* millicelsius */ };&cpu_crit { temperature = <90000>; /* millicelsius */ };Signed-off-by Adam Ford <[email protected]>---
V2: Change the CPU reference to &cpu instead of &cpu0arch/arm/boot/dts/omap3-cpu-thermal.dtsi +21
-1@@ -17,4 +17,25 @@ cpu_thermal: cpu_thermal { /* sensor ID */ thermal-sensors = <&bandgap 0>; + + cpu_trips: trips { + cpu_alert0: cpu_alert { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <105000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cpu_cooling_maps: cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; --Quoted 2 lines
2.17.1
Here is my test log (GTA04A5 with DM3730CBP100). "high-load" script is driving the NEON to full power and would report calculation errors.
Quoted 4 lines
There is no noise visible in the bandgap sensor data induced by power supply fluctuations (log shows system voltage while charging).
Great data!
Quoted 46 lines
root@letux:~# ./high-load -n2 100% load stress test for 1 cores running ./neon_loop2 Sat Sep 14 09:05:50 UTC 2019 65° 4111mV 1000MHz Sat Sep 14 09:05:50 UTC 2019 67° 4005mV 1000MHz Sat Sep 14 09:05:52 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:53 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:55 UTC 2019 72° 3976mV 1000MHz Sat Sep 14 09:05:56 UTC 2019 72° 4023mV 1000MHz Sat Sep 14 09:05:57 UTC 2019 72° 3900mV 1000MHz Sat Sep 14 09:05:59 UTC 2019 73° 4029mV 1000MHz Sat Sep 14 09:06:00 UTC 2019 73° 3988mV 1000MHz Sat Sep 14 09:06:01 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:03 UTC 2019 73° 4011mV 1000MHz Sat Sep 14 09:06:04 UTC 2019 73° 4117mV 1000MHz Sat Sep 14 09:06:06 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:07 UTC 2019 75° 3994mV 1000MHz Sat Sep 14 09:06:08 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:09 UTC 2019 75° 4046mV 1000MHz Sat Sep 14 09:06:11 UTC 2019 75° 4005mV 1000MHz Sat Sep 14 09:06:12 UTC 2019 75° 4023mV 1000MHz Sat Sep 14 09:06:14 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:15 UTC 2019 75° 4011mV 1000MHz Sat Sep 14 09:06:16 UTC 2019 77° 4017mV 1000MHz Sat Sep 14 09:06:18 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:19 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:20 UTC 2019 77° 3988mV 1000MHz Sat Sep 14 09:06:22 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:23 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:24 UTC 2019 78° 4005mV 1000MHz Sat Sep 14 09:06:26 UTC 2019 78° 4105mV 1000MHz Sat Sep 14 09:06:27 UTC 2019 78° 4011mV 1000MHz Sat Sep 14 09:06:28 UTC 2019 78° 3994mV 1000MHz Sat Sep 14 09:06:30 UTC 2019 78° 4123mV 1000MHz ... Sat Sep 14 09:09:57 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:09:59 UTC 2019 88° 4164mV 1000MHz Sat Sep 14 09:10:00 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:01 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:03 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:10:04 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:06 UTC 2019 88° 4146mV 1000MHz Sat Sep 14 09:10:07 UTC 2019 88° 4041mV 1000MHz Sat Sep 14 09:10:08 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:10 UTC 2019 88° 4052mV 1000MHz Sat Sep 14 09:10:11 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:12 UTC 2019 88° 4152mV 1000MHzQuoted 8 lines
Sat Sep 14 09:10:14 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:15 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:17 UTC 2019 88° 4170mV 1000MHz Sat Sep 14 09:10:18 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:19 UTC 2019 88° 4187mV 1000MHz Sat Sep 14 09:10:21 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:22 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:23 UTC 2019 90° 4070mV 1000MHzQuoted 4 lines
Should we be a little more conservative? Without knowing the accuracy, i believe we do not want to run at 800 or 1GHz at 90C, so if we made this value 89 instead of 90, we would throttle a little more conservatively.
Well, the OMAP5 also defines exactly 100°C in the device tree.
I would assume that the badgap sensor accuracy is so that it never reports less than the real temperature. So if we throttle at reported 90° TJ is likely lower.
Quoted 5 lines
Quoted 3 lines
Sat Sep 14 09:10:25 UTC 2019 88° 4123mV 800MHz Sat Sep 14 09:10:26 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:28 UTC 2019 90° 4058mV 1000MHz
Again here, I interpret the data sheet correctly, we're technically out of spec
I read the data sheet as if 90°C at OPP1G is still within spec. 91 would be obviously outside (if bandgap sensor is precise).
Quoted 45 lines
Quoted 45 lines
Sat Sep 14 09:10:29 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:30 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:32 UTC 2019 88° 4117mV 1000MHz Sat Sep 14 09:10:33 UTC 2019 88° 4105mV 800MHz Sat Sep 14 09:10:34 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:36 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:37 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:39 UTC 2019 88° 4017mV 1000MHz Sat Sep 14 09:10:40 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:41 UTC 2019 88° 4058mV 800MHz Sat Sep 14 09:10:42 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:44 UTC 2019 90° 4058mV 1000MHz Sat Sep 14 09:10:45 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:47 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:48 UTC 2019 88° 4029mV 1000MHz Sat Sep 14 09:10:50 UTC 2019 90° 4046mV 1000MHz ^Ckill 4680
root@letux:~# cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 CPUs which need to have their frequency coordinated by software: 0 maximum transition latency: 300 us. hardware limits: 300 MHz - 1000 MHz available frequency steps: 300 MHz, 600 MHz, 800 MHz, 1000 MHz available cpufreq governors: conservative, userspace, powersave, ondemand, performance current policy: frequency should be within 300 MHz and 1000 MHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency is 600 MHz (asserted by call to hardware). cpufreq stats: 300 MHz:22.81%, 600 MHz:2.50%, 800 MHz:2.10%, 1000 MHz:72.59% (1563) root@letux:~#So OPP is reduced if bandgap sensor reports >= 90°C which almost immediately makes the temperature go down.
No operational hickups were observed.
Surface temperature of the PoP chip did rise to approx. 53°C during this test.
Quoted 6 lines
Quoted 2 lines
Quoted 2 lines
BTW: this patch (set) is even independent of my 1GHz OPP patches. Should also work with OPP-v1 definitions so that maintainers can decide which one to apply first.
If I am going integrate the cooling references into &cpu node, I'll probably base it on your work since the cooling isn't really that important until we exceed 800MHz. If I do it on the current linux master or omap for-next branch, it may not apply cleanly.
Quoted 2 lines
It is just more difficult to reach TJ of 90°C without 1GHz.
If it even does at all without external influences.
adam
Quoted 4 lines
BR,
Nikolaus
Quoted 31 lines · H. Nikolaus Schaller
Quoted 22 lines
Am 07.10.2019 um 17:11 schrieb Adam Ford <[email protected]>:
Quoted 9 lines · Adam Ford
Quoted 7 lines · H. Nikolaus Schaller
Quoted 7 lines
Am 14.09.2019 um 15:42 schrieb Adam Ford <[email protected]>:
Quoted 2 lines · H. Nikolaus Schaller
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Am 13.09.2019 um 17:37 schrieb Adam Ford <[email protected]>:
The OMAP3530, AM3517 and DM3730 all show thresholds of 90C and 105C depending on commercial or industrial temperature ratings. This patch expands the thermal information to the limits of 90 and 105 for alert and critical.
Quoted 8 lines
Tom / anyone from TI,
I am going to rebase this patch from the current 5.4-RC branch, remove the AM3517 references, and leave the throttling only applicable to omap34xx and 36xx (like it is now), and remove the RFC. Before I do that, I was hoping for some feedback on whether or not there is a reason to not do this while acknowledging the thermal sensor isn't very accurate.
Quoted 2 lines
I wonder if there is a more precise definition what "isn't very accurate" means?
That's what I was trying to get by asking TI for feedback.
Quoted 3 lines
Is it just because the
TI_BANDGAP_FEATURE_UNRELIABLEbit is set in the driver and we assume that it is right?
The bandgap sensor is disabled by default and, when enabled, it throws a comment saying 'You've been warned' so I mostly want to acknowledge that in the patch.
Quoted 4 lines
Of course the "junction temperature" (TJ) is not well defined (at which edge? in which area?) and the bandgap sensor can only report a single point of the die. So e.g. the GPU or the NEON unit may be hotter or cooler.
I look forward to running the GPU again. ;-)
Quoted 7 lines
And, the bandgap sensor + ADC is unlikely to be well calibrated to 0.1°C precision.
But in my experiments there seems to be not much noise and values rise or fall monotonic according to expectations of processor load.
Quoted 8 lines
So a report of 90°C may not be exactly 90°C and some parts of the SoC may be hotter.
I would also assume that the TJ limits of 90°C have some safety margin but there seems to be no information in the data sheet.
So, IMHO an "unreliable" bandgap sensor is better than no sensor and no trips / cooling maps.
I completely agree.
Quoted 220 lines
One more thing is with the omap3 bandgap sensor (driver?). It appears to report the value of the previous measurement. So unless it is regularily polled (like cpufreq seems to do) it will report outdated values. The first read hours after boot may report the value during probe while booting.
This is also a source of missing accuracy of course. But I haven't investigated this (can only be tested if thermal management is turned off) because I think it has no practical influence if cpufreq is polling.
Quoted 209 lines
Does anyone have any objections to this?
Other than the omap mailing list, are there other lists that should be CC'd?
adam
Quoted 202 lines
Quoted 180 lines
Quoted 115 lines
Quoted 53 lines
Quoted 46 lines
For boards who never use industrial temperatures, these can be changed on their respective device trees with something like:
&cpu_alert0 { temperature = <85000>; /* millicelsius */ };&cpu_crit { temperature = <90000>; /* millicelsius */ };Signed-off-by Adam Ford <[email protected]>---
V2: Change the CPU reference to &cpu instead of &cpu0arch/arm/boot/dts/omap3-cpu-thermal.dtsi +21
-1@@ -17,4 +17,25 @@ cpu_thermal: cpu_thermal { /* sensor ID */ thermal-sensors = <&bandgap 0>; + + cpu_trips: trips { + cpu_alert0: cpu_alert { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <105000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cpu_cooling_maps: cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; --Quoted 2 lines
2.17.1
Here is my test log (GTA04A5 with DM3730CBP100). "high-load" script is driving the NEON to full power and would report calculation errors.
Quoted 4 lines
There is no noise visible in the bandgap sensor data induced by power supply fluctuations (log shows system voltage while charging).
Great data!
Quoted 46 lines
root@letux:~# ./high-load -n2 100% load stress test for 1 cores running ./neon_loop2 Sat Sep 14 09:05:50 UTC 2019 65° 4111mV 1000MHz Sat Sep 14 09:05:50 UTC 2019 67° 4005mV 1000MHz Sat Sep 14 09:05:52 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:53 UTC 2019 68° 4000mV 1000MHz Sat Sep 14 09:05:55 UTC 2019 72° 3976mV 1000MHz Sat Sep 14 09:05:56 UTC 2019 72° 4023mV 1000MHz Sat Sep 14 09:05:57 UTC 2019 72° 3900mV 1000MHz Sat Sep 14 09:05:59 UTC 2019 73° 4029mV 1000MHz Sat Sep 14 09:06:00 UTC 2019 73° 3988mV 1000MHz Sat Sep 14 09:06:01 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:03 UTC 2019 73° 4011mV 1000MHz Sat Sep 14 09:06:04 UTC 2019 73° 4117mV 1000MHz Sat Sep 14 09:06:06 UTC 2019 73° 4005mV 1000MHz Sat Sep 14 09:06:07 UTC 2019 75° 3994mV 1000MHz Sat Sep 14 09:06:08 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:09 UTC 2019 75° 4046mV 1000MHz Sat Sep 14 09:06:11 UTC 2019 75° 4005mV 1000MHz Sat Sep 14 09:06:12 UTC 2019 75° 4023mV 1000MHz Sat Sep 14 09:06:14 UTC 2019 75° 3970mV 1000MHz Sat Sep 14 09:06:15 UTC 2019 75° 4011mV 1000MHz Sat Sep 14 09:06:16 UTC 2019 77° 4017mV 1000MHz Sat Sep 14 09:06:18 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:19 UTC 2019 77° 3994mV 1000MHz Sat Sep 14 09:06:20 UTC 2019 77° 3988mV 1000MHz Sat Sep 14 09:06:22 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:23 UTC 2019 77° 4023mV 1000MHz Sat Sep 14 09:06:24 UTC 2019 78° 4005mV 1000MHz Sat Sep 14 09:06:26 UTC 2019 78° 4105mV 1000MHz Sat Sep 14 09:06:27 UTC 2019 78° 4011mV 1000MHz Sat Sep 14 09:06:28 UTC 2019 78° 3994mV 1000MHz Sat Sep 14 09:06:30 UTC 2019 78° 4123mV 1000MHz ... Sat Sep 14 09:09:57 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:09:59 UTC 2019 88° 4164mV 1000MHz Sat Sep 14 09:10:00 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:01 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:03 UTC 2019 88° 4082mV 1000MHz Sat Sep 14 09:10:04 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:06 UTC 2019 88° 4146mV 1000MHz Sat Sep 14 09:10:07 UTC 2019 88° 4041mV 1000MHz Sat Sep 14 09:10:08 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:10 UTC 2019 88° 4052mV 1000MHz Sat Sep 14 09:10:11 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:12 UTC 2019 88° 4152mV 1000MHzQuoted 8 lines
Sat Sep 14 09:10:14 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:15 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:17 UTC 2019 88° 4170mV 1000MHz Sat Sep 14 09:10:18 UTC 2019 88° 4058mV 1000MHz Sat Sep 14 09:10:19 UTC 2019 88° 4187mV 1000MHz Sat Sep 14 09:10:21 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:22 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:23 UTC 2019 90° 4070mV 1000MHzQuoted 4 lines
Should we be a little more conservative? Without knowing the accuracy, i believe we do not want to run at 800 or 1GHz at 90C, so if we made this value 89 instead of 90, we would throttle a little more conservatively.
Well, the OMAP5 also defines exactly 100°C in the device tree.
I would assume that the badgap sensor accuracy is so that it never reports less than the real temperature. So if we throttle at reported 90° TJ is likely lower.
Quoted 5 lines
Quoted 3 lines
Sat Sep 14 09:10:25 UTC 2019 88° 4123mV 800MHz Sat Sep 14 09:10:26 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:28 UTC 2019 90° 4058mV 1000MHz
Again here, I interpret the data sheet correctly, we're technically out of spec
I read the data sheet as if 90°C at OPP1G is still within spec. 91 would be obviously outside (if bandgap sensor is precise).
Quoted 45 lines
Quoted 45 lines
Sat Sep 14 09:10:29 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:30 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:32 UTC 2019 88° 4117mV 1000MHz Sat Sep 14 09:10:33 UTC 2019 88° 4105mV 800MHz Sat Sep 14 09:10:34 UTC 2019 88° 4070mV 1000MHz Sat Sep 14 09:10:36 UTC 2019 88° 4076mV 1000MHz Sat Sep 14 09:10:37 UTC 2019 88° 4087mV 1000MHz Sat Sep 14 09:10:39 UTC 2019 88° 4017mV 1000MHz Sat Sep 14 09:10:40 UTC 2019 88° 4093mV 1000MHz Sat Sep 14 09:10:41 UTC 2019 88° 4058mV 800MHz Sat Sep 14 09:10:42 UTC 2019 88° 4035mV 1000MHz Sat Sep 14 09:10:44 UTC 2019 90° 4058mV 1000MHz Sat Sep 14 09:10:45 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:47 UTC 2019 88° 4064mV 1000MHz Sat Sep 14 09:10:48 UTC 2019 88° 4029mV 1000MHz Sat Sep 14 09:10:50 UTC 2019 90° 4046mV 1000MHz ^Ckill 4680
root@letux:~# cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 CPUs which need to have their frequency coordinated by software: 0 maximum transition latency: 300 us. hardware limits: 300 MHz - 1000 MHz available frequency steps: 300 MHz, 600 MHz, 800 MHz, 1000 MHz available cpufreq governors: conservative, userspace, powersave, ondemand, performance current policy: frequency should be within 300 MHz and 1000 MHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency is 600 MHz (asserted by call to hardware). cpufreq stats: 300 MHz:22.81%, 600 MHz:2.50%, 800 MHz:2.10%, 1000 MHz:72.59% (1563) root@letux:~#So OPP is reduced if bandgap sensor reports >= 90°C which almost immediately makes the temperature go down.
No operational hickups were observed.
Surface temperature of the PoP chip did rise to approx. 53°C during this test.
Quoted 6 lines
Quoted 2 lines
Quoted 2 lines
BTW: this patch (set) is even independent of my 1GHz OPP patches. Should also work with OPP-v1 definitions so that maintainers can decide which one to apply first.
If I am going integrate the cooling references into &cpu node, I'll probably base it on your work since the cooling isn't really that important until we exceed 800MHz. If I do it on the current linux master or omap for-next branch, it may not apply cleanly.
Quoted 2 lines
It is just more difficult to reach TJ of 90°C without 1GHz.
If it even does at all without external influences.
adam
Quoted 4 lines
BR,
Nikolaus
Hi Adam,
what is the status of this RFC/PATCH?
BR and thanks,
Nikolaus
Quoted 3 lines · H. Nikolaus Schaller
Hi Adam,
what is the status of this RFC/PATCH?
I've submitted a formal 2-part patch [1] and [2], but Tony is concerned about power consumption. As of right now, I don't have cycles to work on it. My employer is about to release two new SOM's, and I'm writing up some documentation on some of the older ones to help some of the developers working on the new ones make their job go quicker.
[1] - https://patchwork.kernel.org/patch/11178561/
[2] - https://patchwork.kernel.org/patch/11178563/
I requested if we could apply them as-is with 'status=disabled' for now until the bus is fixed, but I think there was some push-back.
I'm trying to get to it. I am hoping to find a little time this weekend.
adam
Quoted 4 lines
BR and thanks,
Nikolaus