samples: pktgen: make variable consistent with option
Subsystems (2)
PATCH v3 1/3 samples: pktgen: make variable consistent with option
This commit changes variable names that can cause confusion.
For example, variable DST_MIN is quite confusing since the keyword 'udp_dst_min' and keyword 'dst_min' is used with pg_ctrl.
On the following commit, 'dst_min' will be used to set destination IP, and the existing variable name DST_MIN should be changed.
Variable names are matched to the exact keyword used with pg_ctrl.
--- .../pktgen_bench_xmit_mode_netif_receive.sh | 8 ++++---- .../pktgen/pktgen_bench_xmit_mode_queue_xmit.sh | 8 ++++---- samples/pktgen/pktgen_sample01_simple.sh | 16 ++++++++-------- samples/pktgen/pktgen_sample02_multiqueue.sh | 16 ++++++++-------- .../pktgen/pktgen_sample03_burst_single_flow.sh | 8 ++++---- samples/pktgen/pktgen_sample04_many_flows.sh | 8 ++++---- .../pktgen/pktgen_sample05_flow_per_thread.sh | 8 ++++---- ...en_sample06_numa_awared_queue_irq_affinity.sh | 16 ++++++++-------- 8 files changed, 44 insertions(+), 44 deletions(-)
samples/pktgen/pktgen_bench_xmit_mode_netif_receive.sh +4 -4
@@ -42,8 +42,8 @@ fi [ -z "$BURST" ] && BURST=1024 [ -z "$COUNT" ] && COUNT="10000000" # Zero means indefinitely if [ -n "$DST_PORT" ]; then - read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT) - validate_ports $DST_MIN $DST_MAX + read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) + validate_ports $UDP_DST_MIN $UDP_DST_MAX fi # Base Config
@@ -76,8 +76,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do if [ -n "$DST_PORT" ]; then # Single destination port or random port range pg_set $dev "flag UDPDST_RND" - pg_set $dev "udp_dst_min $DST_MIN" - pg_set $dev "udp_dst_max $DST_MAX" + pg_set $dev "udp_dst_min $UDP_DST_MIN" + pg_set $dev "udp_dst_max $UDP_DST_MAX" fi # Inject packet into RX path of stack
samples/pktgen/pktgen_bench_xmit_mode_queue_xmit.sh +4 -4
@@ -25,8 +25,8 @@ if [[ -n "$BURST" ]]; then fi [ -z "$COUNT" ] && COUNT="10000000" # Zero means indefinitely if [ -n "$DST_PORT" ]; then - read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT) - validate_ports $DST_MIN $DST_MAX + read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) + validate_ports $UDP_DST_MIN $UDP_DST_MAX fi # Base Config
@@ -59,8 +59,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do if [ -n "$DST_PORT" ]; then # Single destination port or random port range pg_set $dev "flag UDPDST_RND" - pg_set $dev "udp_dst_min $DST_MIN" - pg_set $dev "udp_dst_max $DST_MAX" + pg_set $dev "udp_dst_min $UDP_DST_MIN" + pg_set $dev "udp_dst_max $UDP_DST_MAX" fi # Inject packet into TX qdisc egress path of stack
samples/pktgen/pktgen_sample01_simple.sh +8 -8
@@ -23,16 +23,16 @@ fi [ -z "$DST_MAC" ] && usage && err 2 "Must specify -m dst_mac" [ -z "$COUNT" ] && COUNT="100000" # Zero means indefinitely if [ -n "$DST_PORT" ]; then - read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT) - validate_ports $DST_MIN $DST_MAX + read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) + validate_ports $UDP_DST_MIN $UDP_DST_MAX fi # Base Config DELAY="0" # Zero means max speed # Flow variation random source port between min and max -UDP_MIN=9 -UDP_MAX=109 +UDP_SRC_MIN=9 +UDP_SRC_MAX=109 # General cleanup everything since last run # (especially important if other threads were configured by other scripts)
@@ -66,14 +66,14 @@ pg_set $DEV "dst$IP6 $DEST_IP" if [ -n "$DST_PORT" ]; then # Single destination port or random port range pg_set $DEV "flag UDPDST_RND" - pg_set $DEV "udp_dst_min $DST_MIN" - pg_set $DEV "udp_dst_max $DST_MAX" + pg_set $DEV "udp_dst_min $UDP_DST_MIN" + pg_set $DEV "udp_dst_max $UDP_DST_MAX" fi # Setup random UDP port src range pg_set $DEV "flag UDPSRC_RND" -pg_set $DEV "udp_src_min $UDP_MIN" -pg_set $DEV "udp_src_max $UDP_MAX" +pg_set $DEV "udp_src_min $UDP_SRC_MIN" +pg_set $DEV "udp_src_max $UDP_SRC_MAX" # start_run echo "Running... ctrl^C to stop" >&2
samples/pktgen/pktgen_sample02_multiqueue.sh +8 -8
@@ -21,8 +21,8 @@ DELAY="0" # Zero means max speed [ -z "$CLONE_SKB" ] && CLONE_SKB="0" # Flow variation random source port between min and max -UDP_MIN=9 -UDP_MAX=109 +UDP_SRC_MIN=9 +UDP_SRC_MAX=109 # (example of setting default params in your script) if [ -z "$DEST_IP" ]; then
@@ -30,8 +30,8 @@ if [ -z "$DEST_IP" ]; then fi [ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff" if [ -n "$DST_PORT" ]; then - read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT) - validate_ports $DST_MIN $DST_MAX + read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) + validate_ports $UDP_DST_MIN $UDP_DST_MAX fi # General cleanup everything since last run
@@ -67,14 +67,14 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do if [ -n "$DST_PORT" ]; then # Single destination port or random port range pg_set $dev "flag UDPDST_RND" - pg_set $dev "udp_dst_min $DST_MIN" - pg_set $dev "udp_dst_max $DST_MAX" + pg_set $dev "udp_dst_min $UDP_DST_MIN" + pg_set $dev "udp_dst_max $UDP_DST_MAX" fi # Setup random UDP port src range pg_set $dev "flag UDPSRC_RND" - pg_set $dev "udp_src_min $UDP_MIN" - pg_set $dev "udp_src_max $UDP_MAX" + pg_set $dev "udp_src_min $UDP_SRC_MIN" + pg_set $dev "udp_src_max $UDP_SRC_MAX" done # start_run
samples/pktgen/pktgen_sample03_burst_single_flow.sh +4 -4
@@ -34,8 +34,8 @@ fi [ -z "$CLONE_SKB" ] && CLONE_SKB="0" # No need for clones when bursting [ -z "$COUNT" ] && COUNT="0" # Zero means indefinitely if [ -n "$DST_PORT" ]; then - read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT) - validate_ports $DST_MIN $DST_MAX + read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) + validate_ports $UDP_DST_MIN $UDP_DST_MAX fi # Base Config
@@ -67,8 +67,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do if [ -n "$DST_PORT" ]; then # Single destination port or random port range pg_set $dev "flag UDPDST_RND" - pg_set $dev "udp_dst_min $DST_MIN" - pg_set $dev "udp_dst_max $DST_MAX" + pg_set $dev "udp_dst_min $UDP_DST_MIN" + pg_set $dev "udp_dst_max $UDP_DST_MAX" fi # Setup burst, for easy testing -b 0 disable bursting
samples/pktgen/pktgen_sample04_many_flows.sh +4 -4
@@ -18,8 +18,8 @@ source ${basedir}/parameters.sh [ -z "$CLONE_SKB" ] && CLONE_SKB="0" [ -z "$COUNT" ] && COUNT="0" # Zero means indefinitely if [ -n "$DST_PORT" ]; then - read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT) - validate_ports $DST_MIN $DST_MAX + read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) + validate_ports $UDP_DST_MIN $UDP_DST_MAX fi # NOTICE: Script specific settings
@@ -63,8 +63,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do if [ -n "$DST_PORT" ]; then # Single destination port or random port range pg_set $dev "flag UDPDST_RND" - pg_set $dev "udp_dst_min $DST_MIN" - pg_set $dev "udp_dst_max $DST_MAX" + pg_set $dev "udp_dst_min $UDP_DST_MIN" + pg_set $dev "udp_dst_max $UDP_DST_MAX" fi # Randomize source IP-addresses
samples/pktgen/pktgen_sample05_flow_per_thread.sh +4 -4
@@ -23,8 +23,8 @@ source ${basedir}/parameters.sh [ -z "$BURST" ] && BURST=32 [ -z "$COUNT" ] && COUNT="0" # Zero means indefinitely if [ -n "$DST_PORT" ]; then - read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT) - validate_ports $DST_MIN $DST_MAX + read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) + validate_ports $UDP_DST_MIN $UDP_DST_MAX fi # Base Config
@@ -56,8 +56,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do if [ -n "$DST_PORT" ]; then # Single destination port or random port range pg_set $dev "flag UDPDST_RND" - pg_set $dev "udp_dst_min $DST_MIN" - pg_set $dev "udp_dst_max $DST_MAX" + pg_set $dev "udp_dst_min $UDP_DST_MIN" + pg_set $dev "udp_dst_max $UDP_DST_MAX" fi # Setup source IP-addresses based on thread number
samples/pktgen/pktgen_sample06_numa_awared_queue_irq_affinity.sh +8 -8
@@ -20,8 +20,8 @@ DELAY="0" # Zero means max speed [ -z "$CLONE_SKB" ] && CLONE_SKB="0" # Flow variation random source port between min and max -UDP_MIN=9 -UDP_MAX=109 +UDP_SRC_MIN=9 +UDP_SRC_MAX=109 node=`get_iface_node $DEV` irq_array=(`get_iface_irqs $DEV`)
@@ -36,8 +36,8 @@ if [ -z "$DEST_IP" ]; then fi [ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff" if [ -n "$DST_PORT" ]; then - read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT) - validate_ports $DST_MIN $DST_MAX + read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) + validate_ports $UDP_DST_MIN $UDP_DST_MAX fi # General cleanup everything since last run
@@ -84,14 +84,14 @@ for ((i = 0; i < $THREADS; i++)); do if [ -n "$DST_PORT" ]; then # Single destination port or random port range pg_set $dev "flag UDPDST_RND" - pg_set $dev "udp_dst_min $DST_MIN" - pg_set $dev "udp_dst_max $DST_MAX" + pg_set $dev "udp_dst_min $UDP_DST_MIN" + pg_set $dev "udp_dst_max $UDP_DST_MAX" fi # Setup random UDP port src range pg_set $dev "flag UDPSRC_RND" - pg_set $dev "udp_src_min $UDP_MIN" - pg_set $dev "udp_src_max $UDP_MAX" + pg_set $dev "udp_src_min $UDP_SRC_MIN" + pg_set $dev "udp_src_max $UDP_SRC_MAX" done # start_run
Signature · 1 line
2.20.1
PATCH v3 2/3 samples: pktgen: add helper functions for IP(v4/v6) CIDR parsing
This commit adds CIDR parsing and IP validate helper function to parse single IP or range of IP with CIDR. (e.g. 198.18.0.0/15)
Helpers will be used in prior to set target address in samples/pktgen.
---
Changes since v3:
* Set errexit option to stop script execution on error
samples/pktgen/functions.sh | 124 ++++++++++++++++++++++++++++++++++++ 1 file changed, 124 insertions(+)
samples/pktgen/functions.sh +124 -0
@@ -5,6 +5,8 @@ # Author: Jesper Dangaaard Brouer # License: GPL +set -o errexit + ## -- General shell logging cmds -- function err() { local exitcode=$1
@@ -163,6 +165,128 @@ function get_node_cpus() echo $node_cpu_list } +# Extend shrunken IPv6 address. +# fe80::42:bcff:fe84:e10a => fe80:0:0:0:42:bcff:fe84:e10a +function extend_addr6() +{ + local addr=$1 + local sep=: sep2=:: + local sep_cnt=$(tr -cd $sep <<< $1 | wc -c) + local shrink + + # separator count : should be between 2, 7. + if [[ $sep_cnt -lt 2 || $sep_cnt -gt 7 ]]; then + err 5 "Invalid IP6 address sep: $1" + fi + + # if shrink '::' occurs multiple, it's malformed. + shrink=( $(egrep -o "$sep{2,}" <<< $addr) ) + if [[ ${#shrink[@]} -ne 0 ]]; then + if [[ ${#shrink[@]} -gt 1 || ( ${shrink[0]} != $sep2 ) ]]; then + err 5 "Invalid IP$IP6 address shr: $1" + fi + fi + + # add 0 at begin & end, and extend addr by adding :0 + [[ ${addr:0:1} == $sep ]] && addr=0${addr} + [[ ${addr: -1} == $sep ]] && addr=${addr}0 + echo "${addr/$sep2/$(printf ':0%.s' $(seq $[8-sep_cnt])):}" +} + + +# Given a single IP(v4/v6) address, whether it is valid. +function validate_addr() +{ + # check function is called with (funcname)6 + [[ ${FUNCNAME[1]: -1} == 6 ]] && local IP6=6 + local len=$[ IP6 ? 8 : 4 ] + local max=$[ 2**(len*2)-1 ] + local addr sep + + # set separator for each IP(v4/v6) + [[ $IP6 ]] && sep=: || sep=. + IFS=$sep read -a addr <<< $1 + + # array length + if [[ ${#addr[@]} != $len ]]; then + err 5 "Invalid IP$IP6 address: $1" + fi + + # check each digit between 0, $max + for digit in "${addr[@]}"; do + [[ $IP6 ]] && digit=$[ 16#$digit ] + if [[ $digit -lt 0 || $digit -gt $max ]]; then + err 5 "Invalid IP$IP6 address: $1" + fi + done + + return 0 +} + +function validate_addr6() { validate_addr $@ ; } + +# Given a single IP(v4/v6) or CIDR, return minimum and maximum IP addr. +function parse_addr() +{ + # check function is called with (funcname)6 + [[ ${FUNCNAME[1]: -1} == 6 ]] && local IP6=6 + local bitlen=$[ IP6 ? 128 : 32 ] + local octet=$[ IP6 ? 16 : 8 ] + + local addr=$1 + local net prefix + local min_ip max_ip + + IFS='/' read net prefix <<< $addr + [[ $IP6 ]] && net=$(extend_addr6 $net) + validate_addr$IP6 $net + + if [[ $prefix -gt $bitlen ]]; then + err 5 "Invalid prefix: $prefix" + elif [[ -z $prefix ]]; then + min_ip=$net + max_ip=$net + else + # defining array for converting Decimal 2 Binary + # 00000000 00000001 00000010 00000011 00000100 ... + local d2b='{0..1}{0..1}{0..1}{0..1}{0..1}{0..1}{0..1}{0..1}' + [[ $IP6 ]] && d2b+=$d2b + eval local D2B=($d2b) + + local remain=$[ bitlen-prefix ] + local min_mask max_mask + local min max + local ip_bit + local ip sep + + # set separator for each IP(v4/v6) + [[ $IP6 ]] && sep=: || sep=. + IFS=$sep read -ra ip <<< $net + + min_mask="$(printf '1%.s' $(seq $prefix))$(printf '0%.s' $(seq $remain))" + max_mask="$(printf '0%.s' $(seq $prefix))$(printf '1%.s' $(seq $remain))" + + # calculate min/max ip with &,| operator + for i in "${!ip[@]}"; do + digit=$[ IP6 ? 16#${ip[$i]} : ${ip[$i]} ] + ip_bit=${D2B[$digit]} + + idx=$[ octet*i ] + min[$i]=$[ 2#$ip_bit & 2#${min_mask:$idx:$octet} ] + max[$i]=$[ 2#$ip_bit | 2#${max_mask:$idx:$octet} ] + [[ $IP6 ]] && { min[$i]=$(printf '%X' ${min[$i]}); + max[$i]=$(printf '%X' ${max[$i]}); } + done + + min_ip=$(IFS=$sep; echo "${min[*]}") + max_ip=$(IFS=$sep; echo "${max[*]}") + fi + + echo $min_ip $max_ip +} + +function parse_addr6() { parse_addr $@ ; } + # Given a single or range of port(s), return minimum and maximum port number. function parse_ports() {
Signature · 1 line
2.20.1
Re: [v3 2/3] samples: pktgen: add helper functions for IP(v4/v6) CIDR parsing
Quoted 18 lines · On Sun, 15 Sep 2019 00:13:52 +0900 "Daniel T. Lee" <[email protected]>…
This commit adds CIDR parsing and IP validate helper function to parse single IP or range of IP with CIDR. (e.g. 198.18.0.0/15)
Helpers will be used in prior to set target address in
samples/pktgen.Signed-off-by Daniel T. Lee <[email protected]>---
Changes since v3:
* Set errexit option to stop script execution on errorsamples/pktgen/functions.sh | 124 ++++++++++++++++++++++++++++++++++++ 1 file changed, 124 insertions(+)samples/pktgen/functions.sh +0
-0
samples/pktgen/functions.sh line 8
Quoted 4 lines
samples/pktgen/functions.sh +1
-0@@ -5,6 +5,8 @@ # Author: Jesper Dangaaard Brouer # License: GPL +set -o errexit
Unfortunately, this breaks the scripts.
The function proc_cmd are designed to grep after "Result: OK:" which might fail, and your patch/change makes the script stop immediately. We actually want to continue, and output what command that failed (and also grep again after "Result:" to provide the kernel reason).
Even if you somehow "fix" function proc_cmd, then we in general want to catch different error situations by looking at status $?, and output meaning full errors via calling err() function. IHMO as minimum with errexit you need a 'trap' function that can help/inform the user of what went wrong.
Signature · 4 lines
Best regards, Jesper Dangaard Brouer MSc.CS, Principal Kernel Engineer at Red Hat LinkedIn: http://www.linkedin.com/in/brouer
Re: [v3 2/3] samples: pktgen: add helper functions for IP(v4/v6) CIDR parsing
Quoted 28 lines · Jesper Dangaard Brouer
Quoted 18 lines · On Sun, 15 Sep 2019 00:13:52 +0900 "Daniel T. Lee" <[email protected]>…
This commit adds CIDR parsing and IP validate helper function to parse single IP or range of IP with CIDR. (e.g. 198.18.0.0/15)
Helpers will be used in prior to set target address in
samples/pktgen.Signed-off-by Daniel T. Lee <[email protected]>---
Changes since v3:
* Set errexit option to stop script execution on errorsamples/pktgen/functions.sh | 124 ++++++++++++++++++++++++++++++++++++ 1 file changed, 124 insertions(+)samples/pktgen/functions.sh +0
-0samples/pktgen/functions.sh line 8
Quoted 4 lines
samples/pktgen/functions.sh +1
-0@@ -5,6 +5,8 @@ # Author: Jesper Dangaaard Brouer # License: GPL +set -o errexitUnfortunately, this breaks the scripts.
Quoted 8 lines
The function
proc_cmdare designed to grep after "Result: OK:" which might fail, and your patch/change makes the script stop immediately. We actually want to continue, and output what command that failed (and also grep again after "Result:" to provide the kernel reason).Even if you somehow "fix" function
proc_cmd, then we in general want to catch different error situations by looking at status $?, and output meaning full errors via callingerr()function.
Yeah, I can see that some functions do this, but I don't think that would be too hard to fix. See sample diff below (will need some more work to deal with grep failing, but you get the idea).
I'd argue that fixing this is the right thing to do... Maybe add set -o nounset as well while we're at it? :)
Quoted 2 lines
IHMO as minimum with errexit you need a 'trap' function that can help/inform the user of what went wrong.
Yeah, trap ERR (which would also need set -o errtrace to work inside the functions) might be useful in any case.
-Toke
samples/pktgen/functions.sh +2 -2
@@ -58,6 +58,7 @@ function pg_set() { function proc_cmd() { local result local proc_file=$1 + local status=0 # after shift, the remaining args are contained in $@ shift local proc_ctrl=${PROC_DIR}/$proc_file
@@ -73,8 +74,7 @@ function proc_cmd() { echo "cmd: $@ > $proc_ctrl" fi # Quoting of "$@" is important for space expansion - echo "$@" > "$proc_ctrl" - local status=$? + echo "$@" > "$proc_ctrl" || status=$? result=$(grep "Result: OK:" $proc_ctrl) # Due to pgctrl, cannot use exit code $? from grep
Re: [v3 2/3] samples: pktgen: add helper functions for IP(v4/v6) CIDR parsing
Thanks for the feedback!
How about just capturing with "Result: OK" except for 'pgctrl'? (more details are in the diff below)
~/git/linux/net$ ag -Q 'Result:'
core/pktgen.c
702: seq_printf(seq, "Result: %s\n", pkt_dev->result);
704: seq_puts(seq, "Result: Idle\n");
1739: seq_printf(seq, "\nResult: %s\n", t->result);
1741: seq_puts(seq, "\nResult: NA\n");The upper command shows that 'Result: ' string is only printed on 'pktgen_if' and 'pktgen_thread'. So I thought just changing to below diff will solve the problem.
samples/pktgen/functions.sh +8 -6
@@ -60,6 +60,7 @@ function pg_set() { function proc_cmd() { local result local proc_file=$1 + local status=0 # after shift, the remaining args are contained in $@ shift local proc_ctrl=${PROC_DIR}/$proc_file
@@ -75,13 +76,14 @@ function proc_cmd() { echo "cmd: $@ > $proc_ctrl" fi # Quoting of "$@" is important for space expansion - echo "$@" > "$proc_ctrl" - local status=$? + echo "$@" > "$proc_ctrl" || status=$? - result=$(grep "Result: OK:" $proc_ctrl) - # Due to pgctrl, cannot use exit code $? from grep - if [[ "$result" == "" ]]; then - grep "Result:" $proc_ctrl >&2 + if [[ "$proc_file" != "pgctrl" ]]; then + result=$(grep "Result: OK:" $proc_ctrl) || true + # Due to pgctrl, cannot use exit code $? from grep + if [[ "$result" == "" ]]; then + grep "Result:" $proc_ctrl >&2 + fi fi
Quoted 2 lines
We actually want to continue, and output what command that failed (and also grep again after "Result:" to provide the kernel reason).
Since, with 'true', the command won't fail and continue, and on error with 'pktgen_if' and 'pktgen_thread', It'll grep again after "Result:" to provide the kernel reason. [1][2]
Quoted 2 lines
I'd argue that fixing this is the right thing to do... Maybe add set -o nounset as well while we're at it? :)
Adding nounset option could break working with $IP6. Most of the scripts tries to check if $IP6 variable exists whether it is defined or not.
Quoted 5 lines
Even if you somehow "fix" function
proc_cmd, then we in general want to catch different error situations by looking at status $?, and output meaning full errors via callingerr()function. IHMO as minimum with errexit you need a 'trap' function that can help/inform the user of what went wrong.
I agree. trap ERR will help with more sophisticated handling of errors, but I'm not sure which to elaborate more (about what went wrong) compared to current error format? (which is grep again after "Result:" to provide the kernel reason.)
I really appreciate your time and effort for the review.
Thanks,
Daniel
[1]: pktgen_if_show:
https://elixir.bootlin.com/linux/latest/source/net/core/pktgen.c#L702
[2]: pktgen_thread_show:
https://elixir.bootlin.com/linux/latest/source/net/core/pktgen.c#L1739
PATCH v3 3/3 samples: pktgen: allow to specify destination IP range (CIDR)
In reply to Daniel T. LeeCurrently, kernel pktgen has the feature to specify destination address range for sending packet. (e.g. pgset "dst_min/dst_max")
But on samples, each of the scripts doesn't have any option to achieve this.
This commit adds the feature to specify the destination address range with CIDR.
-d : ($DEST_IP) destination IP. CIDR (e.g. 198.18.0.0/15) is also allowed
# ./pktgen_sample01_simple.sh -6 -d fe80::20/126 -p 3000 -n 4
# tcpdump ip6 and udp
05:14:18.082285 IP6 fe80::99.71 > fe80::23.3000: UDP, length 16
05:14:18.082564 IP6 fe80::99.43 > fe80::23.3000: UDP, length 16
05:14:18.083366 IP6 fe80::99.107 > fe80::22.3000: UDP, length 16
05:14:18.083585 IP6 fe80::99.97 > fe80::21.3000: UDP, length 16--- samples/pktgen/README.rst | 2 +- samples/pktgen/parameters.sh | 2 +- .../pktgen/pktgen_bench_xmit_mode_netif_receive.sh | 4 +++- samples/pktgen/pktgen_bench_xmit_mode_queue_xmit.sh | 4 +++- samples/pktgen/pktgen_sample01_simple.sh | 4 +++- samples/pktgen/pktgen_sample02_multiqueue.sh | 4 +++- samples/pktgen/pktgen_sample03_burst_single_flow.sh | 4 +++- samples/pktgen/pktgen_sample04_many_flows.sh | 11 ++++++++--- samples/pktgen/pktgen_sample05_flow_per_thread.sh | 4 +++- .../pktgen_sample06_numa_awared_queue_irq_affinity.sh | 4 +++- 10 files changed, 31 insertions(+), 12 deletions(-)
samples/pktgen/README.rst +1 -1
@@ -18,7 +18,7 @@ across the sample scripts. Usage example is printed on errors:: Usage: ./pktgen_sample01_simple.sh [-vx] -i ethX -i : ($DEV) output interface/device (required) -s : ($PKT_SIZE) packet size - -d : ($DEST_IP) destination IP + -d : ($DEST_IP) destination IP. CIDR (e.g. 198.18.0.0/15) is also allowed -m : ($DST_MAC) destination MAC-addr -p : ($DST_PORT) destination PORT range (e.g. 433-444) is also allowed -t : ($THREADS) threads to start
samples/pktgen/parameters.sh +1 -1
@@ -8,7 +8,7 @@ function usage() { echo "Usage: $0 [-vx] -i ethX" echo " -i : (\$DEV) output interface/device (required)" echo " -s : (\$PKT_SIZE) packet size" - echo " -d : (\$DEST_IP) destination IP" + echo " -d : (\$DEST_IP) destination IP. CIDR (e.g. 198.18.0.0/15) is also allowed" echo " -m : (\$DST_MAC) destination MAC-addr" echo " -p : (\$DST_PORT) destination PORT range (e.g. 433-444) is also allowed" echo " -t : (\$THREADS) threads to start"
samples/pktgen/pktgen_bench_xmit_mode_netif_receive.sh +3 -1
@@ -41,6 +41,7 @@ fi [ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff" [ -z "$BURST" ] && BURST=1024 [ -z "$COUNT" ] && COUNT="10000000" # Zero means indefinitely +[ -n "$DEST_IP" ] && read -r DST_MIN DST_MAX <<< $(parse_addr${IP6} $DEST_IP) if [ -n "$DST_PORT" ]; then read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) validate_ports $UDP_DST_MIN $UDP_DST_MAX
@@ -71,7 +72,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do # Destination pg_set $dev "dst_mac $DST_MAC" - pg_set $dev "dst$IP6 $DEST_IP" + pg_set $dev "dst${IP6}_min $DST_MIN" + pg_set $dev "dst${IP6}_max $DST_MAX" if [ -n "$DST_PORT" ]; then # Single destination port or random port range
samples/pktgen/pktgen_bench_xmit_mode_queue_xmit.sh +3 -1
@@ -24,6 +24,7 @@ if [[ -n "$BURST" ]]; then err 1 "Bursting not supported for this mode" fi [ -z "$COUNT" ] && COUNT="10000000" # Zero means indefinitely +[ -n "$DEST_IP" ] && read -r DST_MIN DST_MAX <<< $(parse_addr${IP6} $DEST_IP) if [ -n "$DST_PORT" ]; then read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) validate_ports $UDP_DST_MIN $UDP_DST_MAX
@@ -54,7 +55,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do # Destination pg_set $dev "dst_mac $DST_MAC" - pg_set $dev "dst$IP6 $DEST_IP" + pg_set $dev "dst${IP6}_min $DST_MIN" + pg_set $dev "dst${IP6}_max $DST_MAX" if [ -n "$DST_PORT" ]; then # Single destination port or random port range
samples/pktgen/pktgen_sample01_simple.sh +3 -1
@@ -22,6 +22,7 @@ fi # Example enforce param "-m" for dst_mac [ -z "$DST_MAC" ] && usage && err 2 "Must specify -m dst_mac" [ -z "$COUNT" ] && COUNT="100000" # Zero means indefinitely +[ -n "$DEST_IP" ] && read -r DST_MIN DST_MAX <<< $(parse_addr${IP6} $DEST_IP) if [ -n "$DST_PORT" ]; then read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) validate_ports $UDP_DST_MIN $UDP_DST_MAX
@@ -61,7 +62,8 @@ pg_set $DEV "flag NO_TIMESTAMP" # Destination pg_set $DEV "dst_mac $DST_MAC" -pg_set $DEV "dst$IP6 $DEST_IP" +pg_set $DEV "dst${IP6}_min $DST_MIN" +pg_set $DEV "dst${IP6}_max $DST_MAX" if [ -n "$DST_PORT" ]; then # Single destination port or random port range
samples/pktgen/pktgen_sample02_multiqueue.sh +3 -1
@@ -29,6 +29,7 @@ if [ -z "$DEST_IP" ]; then [ -z "$IP6" ] && DEST_IP="198.18.0.42" || DEST_IP="FD00::1" fi [ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff" +[ -n "$DEST_IP" ] && read -r DST_MIN DST_MAX <<< $(parse_addr${IP6} $DEST_IP) if [ -n "$DST_PORT" ]; then read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) validate_ports $UDP_DST_MIN $UDP_DST_MAX
@@ -62,7 +63,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do # Destination pg_set $dev "dst_mac $DST_MAC" - pg_set $dev "dst$IP6 $DEST_IP" + pg_set $dev "dst${IP6}_min $DST_MIN" + pg_set $dev "dst${IP6}_max $DST_MAX" if [ -n "$DST_PORT" ]; then # Single destination port or random port range
samples/pktgen/pktgen_sample03_burst_single_flow.sh +3 -1
@@ -33,6 +33,7 @@ fi [ -z "$BURST" ] && BURST=32 [ -z "$CLONE_SKB" ] && CLONE_SKB="0" # No need for clones when bursting [ -z "$COUNT" ] && COUNT="0" # Zero means indefinitely +[ -n "$DEST_IP" ] && read -r DST_MIN DST_MAX <<< $(parse_addr${IP6} $DEST_IP) if [ -n "$DST_PORT" ]; then read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) validate_ports $UDP_DST_MIN $UDP_DST_MAX
@@ -62,7 +63,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do # Destination pg_set $dev "dst_mac $DST_MAC" - pg_set $dev "dst$IP6 $DEST_IP" + pg_set $dev "dst${IP6}_min $DST_MIN" + pg_set $dev "dst${IP6}_max $DST_MAX" if [ -n "$DST_PORT" ]; then # Single destination port or random port range
samples/pktgen/pktgen_sample04_many_flows.sh +8 -3
@@ -17,6 +17,7 @@ source ${basedir}/parameters.sh [ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff" [ -z "$CLONE_SKB" ] && CLONE_SKB="0" [ -z "$COUNT" ] && COUNT="0" # Zero means indefinitely +[ -n "$DEST_IP" ] && read -r DST_MIN DST_MAX <<< $(parse_addr $DEST_IP) if [ -n "$DST_PORT" ]; then read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) validate_ports $UDP_DST_MIN $UDP_DST_MAX
@@ -37,6 +38,9 @@ if [[ -n "$BURST" ]]; then err 1 "Bursting not supported for this mode" fi +# 198.18.0.0 / 198.19.255.255 +read -r SRC_MIN SRC_MAX <<< $(parse_addr 198.18.0.0/15) + # General cleanup everything since last run pg_ctrl "reset"
@@ -58,7 +62,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do # Single destination pg_set $dev "dst_mac $DST_MAC" - pg_set $dev "dst $DEST_IP" + pg_set $dev "dst_min $DST_MIN" + pg_set $dev "dst_max $DST_MAX" if [ -n "$DST_PORT" ]; then # Single destination port or random port range
@@ -69,8 +74,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do # Randomize source IP-addresses pg_set $dev "flag IPSRC_RND" - pg_set $dev "src_min 198.18.0.0" - pg_set $dev "src_max 198.19.255.255" + pg_set $dev "src_min $SRC_MIN" + pg_set $dev "src_max $SRC_MAX" # Limit number of flows (max 65535) pg_set $dev "flows $FLOWS"
samples/pktgen/pktgen_sample05_flow_per_thread.sh +3 -1
@@ -22,6 +22,7 @@ source ${basedir}/parameters.sh [ -z "$CLONE_SKB" ] && CLONE_SKB="0" [ -z "$BURST" ] && BURST=32 [ -z "$COUNT" ] && COUNT="0" # Zero means indefinitely +[ -n "$DEST_IP" ] && read -r DST_MIN DST_MAX <<< $(parse_addr $DEST_IP) if [ -n "$DST_PORT" ]; then read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) validate_ports $UDP_DST_MIN $UDP_DST_MAX
@@ -51,7 +52,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do # Single destination pg_set $dev "dst_mac $DST_MAC" - pg_set $dev "dst $DEST_IP" + pg_set $dev "dst_min $DST_MIN" + pg_set $dev "dst_max $DST_MAX" if [ -n "$DST_PORT" ]; then # Single destination port or random port range
samples/pktgen/pktgen_sample06_numa_awared_queue_irq_affinity.sh +3 -1
@@ -35,6 +35,7 @@ if [ -z "$DEST_IP" ]; then [ -z "$IP6" ] && DEST_IP="198.18.0.42" || DEST_IP="FD00::1" fi [ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff" +[ -n "$DEST_IP" ] && read -r DST_MIN DST_MAX <<< $(parse_addr${IP6} $DEST_IP) if [ -n "$DST_PORT" ]; then read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT) validate_ports $UDP_DST_MIN $UDP_DST_MAX
@@ -79,7 +80,8 @@ for ((i = 0; i < $THREADS; i++)); do # Destination pg_set $dev "dst_mac $DST_MAC" - pg_set $dev "dst$IP6 $DEST_IP" + pg_set $dev "dst${IP6}_min $DST_MIN" + pg_set $dev "dst${IP6}_max $DST_MAX" if [ -n "$DST_PORT" ]; then # Single destination port or random port range
Signature · 1 line
2.20.1