Skip to contentSkip to conversation

spi: atmel: Fix crash when using more than 4 gpio CS

PATCH In review Gregory CLEMENT 3 participants 6 messages Sep 19, 2019 – Sep 20, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 spi: atmel: Fix crash when using more than 4 gpio CS

Even when using a gpio as chip select, the registers controlling the hardware chip select have to be configured. However any of the 4 hardware CS can be controlled.

Until now, the gpio index was used to match an hardware chip select, which limited the number of CS than can be used. Using more than 4 gpios leads to the following kernel crash:

WARNING: CPU: 0 PID: 1 at drivers/spi/spi-atmel.c:1293 atmel_spi_transfer_one_message+0x8b0/0x8ec
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.3.0+ #24
Hardware name: Atmel SAMA5
[<c010d914>] (unwind_backtrace) from [<c010ad84>] (show_stack+0x10/0x14)
[<c010ad84>] (show_stack) from [<c0117d28>] (__warn+0xd8/0xf0)
[<c0117d28>] (__warn) from [<c0117d80>] (warn_slowpath_null+0x40/0x48)
[<c0117d80>] (warn_slowpath_null) from [<c04b21dc>] (atmel_spi_transfer_one_message+0x8b0/0x8ec)
[<c04b21dc>] (atmel_spi_transfer_one_message) from [<c04afb20>] (__spi_pump_messages+0x330/0x510)
[<c04afb20>] (__spi_pump_messages) from [<c04afe5c>] (__spi_sync+0x150/0x158)
[<c04afe5c>] (__spi_sync) from [<c04afe88>] (spi_sync+0x24/0x3c)
[<c04afe88>] (spi_sync) from [<c04aff88>] (spi_write_then_read+0xe8/0x1a8)
[<c04aff88>] (spi_write_then_read) from [<c0454da0>] (_regmap_raw_read+0xec/0x148)
[<c0454da0>] (_regmap_raw_read) from [<c0454f6c>] (regmap_raw_read+0x110/0x238)
[<c0454f6c>] (regmap_raw_read) from [<c04551f4>] (regmap_bulk_read+0x160/0x19c)
[<c04551f4>] (regmap_bulk_read) from [<c0517744>] (rv3029_get_sr+0x28/0x64)
[<c0517744>] (rv3029_get_sr) from [<c0518184>] (rv3029_probe+0x5c/0x260)
[<c0518184>] (rv3029_probe) from [<c04acf90>] (spi_drv_probe+0x88/0xac)
[<c04acf90>] (spi_drv_probe) from [<c043fec8>] (really_probe+0xf0/0x2c8)
[<c043fec8>] (really_probe) from [<c0440214>] (driver_probe_device+0x60/0x16c)
[<c0440214>] (driver_probe_device) from [<c04404c0>] (device_driver_attach+0x58/0x60)
[<c04404c0>] (device_driver_attach) from [<c0440520>] (__driver_attach+0x58/0xcc)
[<c0440520>] (__driver_attach) from [<c043e318>] (bus_for_each_dev+0x78/0xc0)
[<c043e318>] (bus_for_each_dev) from [<c043f33c>] (bus_add_driver+0x15c/0x1e0)
[<c043f33c>] (bus_add_driver) from [<c0440d2c>] (driver_register+0x74/0x108)
[<c0440d2c>] (driver_register) from [<c0a1cb44>] (rv30x9_init+0x38/0x68)
[<c0a1cb44>] (rv30x9_init) from [<c0102608>] (do_one_initcall+0x58/0x1c0)
[<c0102608>] (do_one_initcall) from [<c0a00e88>] (kernel_init_freeable+0x124/0x1c0)
[<c0a00e88>] (kernel_init_freeable) from [<c0774dc0>] (kernel_init+0x8/0x10c)
[<c0774dc0>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
Exception stack(0xcf429fb0 to 0xcf429ff8)

9fa0: 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000

With this patch, when using a gpio CS, the hardware CS0 is always used. Thanks to this, there is no more limitation for the number of gpio CS we can use.

Fixes 754ce4f29937 ("[PATCH] SPI: atmel_spi driver")
---
 drivers/spi/spi-atmel.c | 44 ++++++++++++++++++++++++++++++-----------
 1 file changed, 33 insertions(+), 11 deletions(-)
drivers/spi/spi-atmel.c +33 -11
index acf318e7330c..bb94f5927819 100644
@@ -353,22 +353,28 @@ static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
 {
 	struct atmel_spi_device *asd = spi->controller_state;
 	u32 mr;
+	u8 chip_select;
+
+	if (as->use_cs_gpios)
+		chip_select = 0;
+	else
+		chip_select = spi->chip_select;
 
 	if (atmel_spi_is_v2(as)) {
-		spi_writel(as, CSR0 + 4 * spi->chip_select, asd->csr);
+		spi_writel(as, CSR0 + 4 * chip_select, asd->csr);
 		/* For the low SPI version, there is a issue that PDC transfer
 		 * on CS1,2,3 needs SPI_CSR0.BITS config as SPI_CSR1,2,3.BITS
 		 */
 		spi_writel(as, CSR0, asd->csr);
 		if (as->caps.has_wdrbt) {
 			spi_writel(as, MR,
-					SPI_BF(PCS, ~(0x01 << spi->chip_select))
+					SPI_BF(PCS, ~(0x01 << chip_select))
 					| SPI_BIT(WDRBT)
 					| SPI_BIT(MODFDIS)
 					| SPI_BIT(MSTR));
 		} else {
 			spi_writel(as, MR,
-					SPI_BF(PCS, ~(0x01 << spi->chip_select))
+					SPI_BF(PCS, ~(0x01 << chip_select))
 					| SPI_BIT(MODFDIS)
 					| SPI_BIT(MSTR));
 		}
@@ -390,8 +396,8 @@ static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
 		}
 
 		mr = spi_readl(as, MR);
-		mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
-		if (as->use_cs_gpios && spi->chip_select != 0)
+		mr = SPI_BFINS(PCS, ~(1 << chip_select), mr);
+		if (as->use_cs_gpios && chip_select != 0)
 			gpiod_set_value(asd->npcs_pin, 1);
 		spi_writel(as, MR, mr);
 	}
@@ -403,12 +409,18 @@ static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
 {
 	struct atmel_spi_device *asd = spi->controller_state;
 	u32 mr;
+	u8 chip_select;
+
+	if (as->use_cs_gpios)
+		chip_select = 0;
+	else
+		chip_select = spi->chip_select;
 
 	/* only deactivate *this* device; sometimes transfers to
 	 * another device may be active when this routine is called.
 	 */
 	mr = spi_readl(as, MR);
-	if (~SPI_BFEXT(PCS, mr) & (1 << spi->chip_select)) {
+	if (~SPI_BFEXT(PCS, mr) & (1 << chip_select)) {
 		mr = SPI_BFINS(PCS, 0xf, mr);
 		spi_writel(as, MR, mr);
 	}
@@ -417,7 +429,7 @@ static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
 
 	if (!as->use_cs_gpios)
 		spi_writel(as, CR, SPI_BIT(LASTXFER));
-	else if (atmel_spi_is_v2(as) || spi->chip_select != 0)
+	else if (atmel_spi_is_v2(as) || chip_select != 0)
 		gpiod_set_value(asd->npcs_pin, 0);
 }
 
@@ -844,6 +856,12 @@ static int atmel_spi_set_xfer_speed(struct atmel_spi *as,
 {
 	u32			scbr, csr;
 	unsigned long		bus_hz;
+	u8 chip_select;
+
+	if (as->use_cs_gpios)
+		chip_select = 0;
+	else
+		chip_select = spi->chip_select;
 
 	/* v1 chips start out at half the peripheral bus speed. */
 	bus_hz = as->spi_clk;
@@ -872,9 +890,9 @@ static int atmel_spi_set_xfer_speed(struct atmel_spi *as,
 			xfer->speed_hz, scbr, bus_hz);
 		return -EINVAL;
 	}
-	csr = spi_readl(as, CSR0 + 4 * spi->chip_select);
+	csr = spi_readl(as, CSR0 + 4 * chip_select);
 	csr = SPI_BFINS(SCBR, scbr, csr);
-	spi_writel(as, CSR0 + 4 * spi->chip_select, csr);
+	spi_writel(as, CSR0 + 4 * chip_select, csr);
 
 	return 0;
 }
@@ -1238,8 +1256,12 @@ static int atmel_spi_setup(struct spi_device *spi)
 		"setup: bpw %u mode 0x%x -> csr%d %08x\n",
 		bits, spi->mode, spi->chip_select, csr);
 
-	if (!atmel_spi_is_v2(as))
-		spi_writel(as, CSR0 + 4 * spi->chip_select, csr);
+	if (!atmel_spi_is_v2(as)) {
+		if (as->use_cs_gpios)
+			spi_writel(as, CSR0, csr);
+		else
+			spi_writel(as, CSR0 + 4 * spi->chip_select, csr);
+	}
 
 	return 0;
 }
Signature · 1 line
2.23.0
maintainer
#1 lore raw
Quoted 3 lines · Gregory CLEMENT

With this patch, when using a gpio CS, the hardware CS0 is always used. Thanks to this, there is no more limitation for the number of gpio CS we can use.

This is going to break any system where we use both a GPIO chip select and chip select 0. Ideally we'd try to figure out an unused chip select to use here...

#2 lore raw
Quoted 9 lines · Mark Brown
Quoted 3 lines · Gregory CLEMENT

With this patch, when using a gpio CS, the hardware CS0 is always used. Thanks to this, there is no more limitation for the number of gpio CS we can use.

This is going to break any system where we use both a GPIO chip select and chip select 0. Ideally we'd try to figure out an unused chip select to use here...

The point is that this use case is already broken and this patch fixes the crash and is easily backportable.

Fixing the CS + gpio CS should probably be done in a separate patch.

Signature · 3 lines
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
maintainer
#3 lore raw
Quoted 10 lines · Alexandre Belloni
Quoted 3 lines · Mark Brown

This is going to break any system where we use both a GPIO chip select and chip select 0. Ideally we'd try to figure out an unused chip select to use here...

The point is that this use case is already broken and this patch fixes the crash and is easily backportable.

Fixing the CS + gpio CS should probably be done in a separate patch.

If the GPIO is overlaid on any of the existing slots (except GPIO 0) then it'll cause GPIO 0 to start toggling. I'm not convinced that the code doesn't currently support that.

#4 lore raw

Hello Mark,

Quoted 7 lines · Alexandre Belloni
Quoted 5 lines · Mark Brown
Quoted 4 lines

This is going to break any system where we use both a GPIO chip select and chip select 0. Ideally we'd try to figure out an unused chip select to use here...

Quoted 8 lines
Quoted 4 lines

The point is that this use case is already broken and this patch fixes the crash and is easily backportable.

Fixing the CS + gpio CS should probably be done in a separate patch.

If the GPIO is overlaid on any of the existing slots (except GPIO 0) then it'll cause GPIO 0 to start toggling. I'm not convinced that the code doesn't currently support that.

Actually, the current code is not designed to mix CS and gpio CS, so this patch doesn't introduce any regression on this side.

But after going further in the details of the driver, this patch could cause a regression for on the old controllers.

I also found other issues in this driver in the chip select management. So I will send a new series fixing all of it.

Gregory

Signature · 3 lines
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com
maintainer
#5 lore raw
Quoted 5 lines · Gregory CLEMENT

But after going further in the details of the driver, this patch could cause a regression for on the old controllers.

I also found other issues in this driver in the chip select management. So I will send a new series fixing all of it.

OK, great - glad at least one of us spotted a real problem!