Skip to contentSkip to conversation

add support for sam9x60ek

PATCH Superseded Tudor.Ambarus at microchip.com 1 participant 13 messages Sep 20, 2019

Subsystems (4)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

cover add support for sam9x60ek

From: Tudor Ambarus <[email protected]>

Add support for sam9x60 SOC, sam9x60ek board, dts, NAND and QSPI. Add defconfigs for MMC, NAND and QSPI.

Nicolas Ferre (1):
ARM: dts: at91: sam9x60: Add macb0 Ethernet controller

Sandeep Sheriker Mallikarjun (4):
ARM: at91: Add sam9x60 soc
ARM: dts: Add dts files for sam9x60ek
board: atmel: Add sam9x60ek board
configs: Add sam9x60ek_mmc_defconfig

Tudor Ambarus (7):
ARM: at91: Rename sama5_sfr.h to at91_sfr.h
ARM: at91: Add SFR definitions
board: sam9x60ek: Add NAND flash support
configs: Add sam9x60ek_nandflash_defconfig
configs: sam9x60ek: Add QSPI_BOOT defines
ARM: dts: at91: sam9x60ek: Enable qspi node
configs: Add sam9x60ek_qspiflash_defconfig

 arch/arm/dts/Makefile                              |   2 +
 arch/arm/dts/sam9x60.dtsi                          | 285 +++++++++++++++++++++
 arch/arm/dts/sam9x60ek-u-boot.dtsi                 | 132 ++++++++++
 arch/arm/dts/sam9x60ek.dts                         |  55 ++++
 arch/arm/mach-at91/Kconfig                         |  11 +
 arch/arm/mach-at91/arm926ejs/Makefile              |   1 +
 arch/arm/mach-at91/arm926ejs/sam9x60_devices.c     | 125 +++++++++
 arch/arm/mach-at91/armv7/sama5d4_devices.c         |   2 +-
 arch/arm/mach-at91/atmel_sfr.c                     |   2 +-
 .../include/mach/{sama5_sfr.h => at91_sfr.h}       |  52 +++-
 arch/arm/mach-at91/include/mach/hardware.h         |   2 +
 arch/arm/mach-at91/include/mach/sam9x60.h          | 169 ++++++++++++
 board/atmel/sam9x60ek/Kconfig                      |  12 +
 board/atmel/sam9x60ek/MAINTAINERS                  |   6 +
 board/atmel/sam9x60ek/Makefile                     |   7 +
 board/atmel/sam9x60ek/sam9x60ek.c                  | 120 +++++++++
 board/laird/wb50n/wb50n.c                          |   2 +-
 configs/sam9x60ek_mmc_defconfig                    |  52 ++++
 configs/sam9x60ek_nandflash_defconfig              |  51 ++++
 configs/sam9x60ek_qspiflash_defconfig              |  73 ++++++
 drivers/clk/at91/clk-utmi.c                        |   2 +-
 include/configs/sam9x60ek.h                        |  95 +++++++
 22 files changed, 1249 insertions(+), 9 deletions(-)
 create mode 100644 arch/arm/dts/sam9x60.dtsi
 create mode 100644 arch/arm/dts/sam9x60ek-u-boot.dtsi
 create mode 100644 arch/arm/dts/sam9x60ek.dts
 create mode 100644 arch/arm/mach-at91/arm926ejs/sam9x60_devices.c
 rename arch/arm/mach-at91/include/mach/{sama5_sfr.h => at91_sfr.h} (53%)
 create mode 100644 arch/arm/mach-at91/include/mach/sam9x60.h
 create mode 100644 board/atmel/sam9x60ek/Kconfig
 create mode 100644 board/atmel/sam9x60ek/MAINTAINERS
 create mode 100644 board/atmel/sam9x60ek/Makefile
 create mode 100644 board/atmel/sam9x60ek/sam9x60ek.c
 create mode 100644 configs/sam9x60ek_mmc_defconfig
 create mode 100644 configs/sam9x60ek_nandflash_defconfig
 create mode 100644 configs/sam9x60ek_qspiflash_defconfig
 create mode 100644 include/configs/sam9x60ek.h
Signature · 1 line
2.9.5
#1 lore raw

PATCH 1/12 ARM: at91: Add sam9x60 soc

From: Sandeep Sheriker Mallikarjun <[email protected]>

Add new Microchip sam9x60 SoC based on an ARM926.

[tudor.ambarus at microchip.com: fix SFR definition]
---
 arch/arm/mach-at91/Kconfig                     |   4 +
 arch/arm/mach-at91/arm926ejs/Makefile          |   1 +
 arch/arm/mach-at91/arm926ejs/sam9x60_devices.c | 125 ++++++++++++++++++
 arch/arm/mach-at91/include/mach/hardware.h     |   2 +
 arch/arm/mach-at91/include/mach/sam9x60.h      | 169 +++++++++++++++++++++++++
 5 files changed, 301 insertions(+)
 create mode 100644 arch/arm/mach-at91/arm926ejs/sam9x60_devices.c
 create mode 100644 arch/arm/mach-at91/include/mach/sam9x60.h
arch/arm/mach-at91/Kconfig +4 -0
index 14343280793b..3cf13042b7b4 100644
@@ -43,6 +43,10 @@ config AT91SAM9X5
 	bool
 	select CPU_ARM926EJS
 
+config SAM9X60
+	bool
+	select CPU_ARM926EJS
+
 config SAMA5D2
 	bool
 	select CPU_V7A
arch/arm/mach-at91/arm926ejs/Makefile +1 -0
index 6b0b28957af5..8de6a2f9661e 100644
@@ -14,6 +14,7 @@ obj-$(CONFIG_AT91SAM9M10G45)	+= at91sam9m10g45_devices.o
 obj-$(CONFIG_AT91SAM9G45)	+= at91sam9m10g45_devices.o
 obj-$(CONFIG_AT91SAM9N12)	+= at91sam9n12_devices.o
 obj-$(CONFIG_AT91SAM9X5)	+= at91sam9x5_devices.o
+obj-$(CONFIG_SAM9X60)		+= sam9x60_devices.o
 obj-$(CONFIG_AT91_EFLASH)	+= eflash.o
 obj-$(CONFIG_AT91_LED)	+= led.o
 obj-y += clock.o
arch/arm/mach-at91/arm926ejs/sam9x60_devices.c new file +125 -0

125 lines not on this page · raw message

arch/arm/mach-at91/include/mach/hardware.h +2 -0
index 3a7752b999f6..88acca854998 100644
@@ -22,6 +22,8 @@
 # include <asm/arch/at91sam9g45.h>
 #elif defined(CONFIG_AT91SAM9N12) || defined(CONFIG_AT91SAM9X5)
 # include <asm/arch/at91sam9x5.h>
+#elif defined(CONFIG_SAM9X60)
+# include <asm/arch/sam9x60.h>
 #elif defined(CONFIG_SAMA5D2)
 # include <asm/arch/sama5d2.h>
 #elif defined(CONFIG_SAMA5D3)
arch/arm/mach-at91/include/mach/sam9x60.h new file +169 -0

169 lines not on this page · raw message

Signature · 1 line
2.9.5
#2 lore raw

PATCH 2/12 ARM: dts: Add dts files for sam9x60ek

In reply to Tudor.Ambarus at microchip.com

From: Sandeep Sheriker Mallikarjun <[email protected]>

add device tree files for sam9x60ek board with below changes.

- Add initial device nodes (pmc, pinctrl, sdhc, dbgu & pit)
- Add the reg property for the pinctrl node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes are used by the board_init_f stage.

[prasanthi.chellakumar at microchip.com: fix style/whitespace issues]

[nicolas.ferre at microchip.com:
- fix gclk,
- fix pio/pinctrl controller definition and allow to have more than only PIOA for this SoC,
- removing pinctrl address]

[claudiu.beznea at microchip.com:
- use SAM9X60's compatible for pinctrl
- add drive strength and slew rate options for SDMMC0 pins.]

[tudor.ambarus at microchip.com:
- u-boot,dm-pre-reloc property in dedicated file,
- fix pit len, starts from 0xFFFFFE40 and it is of len 0x10]

---
 arch/arm/dts/Makefile              |   2 +
 arch/arm/dts/sam9x60.dtsi          | 225 +++++++++++++++++++++++++++++++++++++
 arch/arm/dts/sam9x60ek-u-boot.dtsi | 104 +++++++++++++++++
 arch/arm/dts/sam9x60ek.dts         |  19 ++++
 4 files changed, 350 insertions(+)
 create mode 100644 arch/arm/dts/sam9x60.dtsi
 create mode 100644 arch/arm/dts/sam9x60ek-u-boot.dtsi
 create mode 100644 arch/arm/dts/sam9x60ek.dts
arch/arm/dts/Makefile +2 -0
index 250b9ba505aa..52027786ef50 100644
@@ -690,6 +690,8 @@ dtb-$(CONFIG_TARGET_AT91SAM9X5EK) += \
 	at91sam9x25ek.dtb	\
 	at91sam9x35ek.dtb
 
+dtb-$(CONFIG_TARGET_SAM9X60EK) += sam9x60ek.dtb
+
 dtb-$(CONFIG_TARGET_AT91SAM9N12EK) += at91sam9n12ek.dtb
 
 dtb-$(CONFIG_TARGET_GARDENA_SMART_GATEWAY_AT91SAM) += \
arch/arm/dts/sam9x60.dtsi new file +225 -0

225 lines not on this page · raw message

arch/arm/dts/sam9x60ek-u-boot.dtsi new file +104 -0

104 lines not on this page · raw message

arch/arm/dts/sam9x60ek.dts new file +19 -0
new file mode 100644
index 000000000000..e64566ec8e58
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sam9x60ek.dts - Device Tree file for SAM9X60 EK board
+ *
+ * Copyright (C) 2018 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Sandeep Sheriker M <[email protected]>
+ */
+/dts-v1/;
+#include "sam9x60.dtsi"
+
+/ {
+	model = "Microchip SAM9X60-Ek";
+	compatible = "microchip,sam9x60ek", "microchip,sam9x60", "atmel,at91sam9";
+
+	chosen {
+		stdout-path = &dbgu;
+	};
+};
Signature · 1 line
2.9.5
#3 lore raw

PATCH 3/12 ARM: dts: at91: sam9x60: Add macb0 Ethernet controller

In reply to Tudor.Ambarus at microchip.com

From: Nicolas Ferre <[email protected]>

Add Ethernet controller to dtsi file and enable it on sam9x60ek platform connected with rmii.

---
 arch/arm/dts/sam9x60.dtsi  | 31 +++++++++++++++++++++++++++++++
 arch/arm/dts/sam9x60ek.dts |  5 +++++
 2 files changed, 36 insertions(+)
arch/arm/dts/sam9x60.dtsi +31 -0
index e880dc0068df..a66d0a278a87 100644
@@ -60,6 +60,16 @@
 			#size-cells = <1>;
 			ranges;
 
+			macb0: ethernet at f802c000 {
+				compatible = "cdns,sam9x60-macb", "cdns,macb";
+				reg = <0xf802c000 0x100>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_rmii>;
+				clock-names = "hclk", "pclk";
+				clocks = <&macb0_clk>, <&macb0_clk>;
+				status = "disabled";
+			};
+
 			dbgu: serial at fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
@@ -88,6 +98,22 @@
 					};
 				};
 
+				macb0 {
+					pinctrl_macb0_rmii: macb0_rmii-0 {
+						atmel,pins =
+							<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB0 periph A */
+							 AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB1 periph A */
+							 AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB2 periph A */
+							 AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB3 periph A */
+							 AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB4 periph A */
+							 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB5 periph A */
+							 AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB6 periph A */
+							 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB7 periph A */
+							 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB9 periph A */
+							 AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PB10 periph A */
+					};
+				};
+
 				sdhci0 {
 					pinctrl_sdhci0: sdhci0 {
 						atmel,pins =
@@ -171,6 +197,11 @@
 						#clock-cells = <0>;
 						reg = <47>;
 					};
+
+					macb0_clk: macb0_clk {
+						#clock-cells = <0>;
+						reg = <24>;
+					};
 				};
 
 				generic: gck {
arch/arm/dts/sam9x60ek.dts +5 -0
index e64566ec8e58..6fe9f19f0bc7 100644
@@ -17,3 +17,8 @@
 		stdout-path = &dbgu;
 	};
 };
+
+&macb0 {
+	phy-mode = "rmii";
+	status = "okay";
+};
Signature · 1 line
2.9.5
#4 lore raw

PATCH 4/12 board: atmel: Add sam9x60ek board

In reply to Tudor.Ambarus at microchip.com

From: Sandeep Sheriker Mallikarjun <[email protected]>

Add new board SAM9X60-EK using the ARM926 SAM9X60 SoC.

[tudor.ambarus at microchip.com:
- fix number of DRAM banks:
One DDR2-SDRAM (W972GG6KB 2 Gbit = 16 Mbit x 16 x 8 banks]
- drop SPL related macros
- drop memtest macros
- drop CONFIG_SPI_BOOT, CONFIG_SYS_USE_DATAFLASH related macros
- drop inclusion of asm/arch/at91sam9_smc.h]

---
 arch/arm/mach-at91/Kconfig        |  7 +++++
 board/atmel/sam9x60ek/Kconfig     | 12 ++++++++
 board/atmel/sam9x60ek/MAINTAINERS |  6 ++++
 board/atmel/sam9x60ek/Makefile    |  7 +++++
 board/atmel/sam9x60ek/sam9x60ek.c | 59 ++++++++++++++++++++++++++++++++++++++
 include/configs/sam9x60ek.h       | 60 +++++++++++++++++++++++++++++++++++++++
 6 files changed, 151 insertions(+)
 create mode 100644 board/atmel/sam9x60ek/Kconfig
 create mode 100644 board/atmel/sam9x60ek/MAINTAINERS
 create mode 100644 board/atmel/sam9x60ek/Makefile
 create mode 100644 board/atmel/sam9x60ek/sam9x60ek.c
 create mode 100644 include/configs/sam9x60ek.h
arch/arm/mach-at91/Kconfig +7 -0
index 3cf13042b7b4..85524004f9e4 100644
@@ -160,6 +160,12 @@ config TARGET_GARDENA_SMART_GATEWAY_AT91SAM
 	select BOARD_LATE_INIT
 	select SUPPORT_SPL
 
+config TARGET_SAM9X60EK
+	bool "SAM9X60-EK board"
+	select SAM9X60
+	select BOARD_EARLY_INIT_F
+	select BOARD_LATE_INIT
+
 config TARGET_SAMA5D2_PTC_EK
 	bool "SAMA5D2 PTC EK board"
 	select BOARD_EARLY_INIT_F
@@ -316,6 +322,7 @@ source "board/atmel/at91sam9m10g45ek/Kconfig"
 source "board/atmel/at91sam9n12ek/Kconfig"
 source "board/atmel/at91sam9rlek/Kconfig"
 source "board/atmel/at91sam9x5ek/Kconfig"
+source "board/atmel/sam9x60ek/Kconfig"
 source "board/atmel/sama5d2_ptc_ek/Kconfig"
 source "board/atmel/sama5d2_xplained/Kconfig"
 source "board/atmel/sama5d27_som1_ek/Kconfig"
board/atmel/sam9x60ek/Kconfig new file +12 -0
new file mode 100644
index 000000000000..32fae2108e6e
@@ -0,0 +1,12 @@
+if TARGET_SAM9X60EK
+
+config SYS_BOARD
+	default "sam9x60ek"
+
+config SYS_VENDOR
+	default "atmel"
+
+config SYS_CONFIG_NAME
+	default "sam9x60ek"
+
+endif
board/atmel/sam9x60ek/MAINTAINERS new file +6 -0
new file mode 100644
index 000000000000..93ed5d9f1509
@@ -0,0 +1,6 @@
+SAM9X60EK BOARD
+M:	Sandeep Sheriker M<[email protected]>
+S:	Maintained
+F:	board/atmel/sam9x60ek/
+F:	include/configs/sam9x60ek.h
+F:	configs/sam9x60ek_mmc_defconfig
board/atmel/sam9x60ek/Makefile new file +7 -0
new file mode 100644
index 000000000000..12a406a3bb5c
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2018 Microchip Technology Inc. and its subsidiaries
+#
+# Author: Sandeep Sheriker M <[email protected]>
+
+obj-y += sam9x60ek.o
board/atmel/sam9x60ek/sam9x60ek.c new file +59 -0

59 lines not on this page · raw message

include/configs/sam9x60ek.h new file +60 -0

60 lines not on this page · raw message

Signature · 1 line
2.9.5
#5 lore raw

PATCH 5/12 configs: Add sam9x60ek_mmc_defconfig

In reply to Tudor.Ambarus at microchip.com

From: Sandeep Sheriker Mallikarjun <[email protected]>

add sam9x60ek_mmc_defconfig and for now only supports booting from sdcard.

[nicolas.ferre at microchip.com: split patch, add Ethernet controller, phy and tools]

[claudiu.beznea at microchip.com: add CONFIG_OF_LIBFDT_OVERLAY]

[tudor.ambarus at microchip.com: Fix number of DRAM banks:
One DDR2-SDRAM (W972GG6KB 2 Gbit = 16 Mbit x 16 x 8 banks]

---
 configs/sam9x60ek_mmc_defconfig | 52 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 configs/sam9x60ek_mmc_defconfig
configs/sam9x60ek_mmc_defconfig new file +52 -0
new file mode 100644
index 000000000000..6cdc819a6793
@@ -0,0 +1,52 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_SYS_TEXT_BASE=0x23f00000
+CONFIG_TARGET_SAM9X60EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_ENV_SIZE=0x4000
+CONFIG_NR_DRAM_BANKS=8
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEBUG_UART=y
+CONFIG_FIT=y
+CONFIG_SD_BOOT=y
+CONFIG_BOOTDELAY=3
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="mem=256M console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait"
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="U-Boot> "
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_MMC=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="sam9x60ek"
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_PHY_MICREL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_TIMER=y
+CONFIG_ATMEL_PIT_TIMER=y
+CONFIG_OF_LIBFDT_OVERLAY=y
Signature · 1 line
2.9.5
#6 lore raw

PATCH 6/12 ARM: at91: Rename sama5_sfr.h to at91_sfr.h

In reply to Tudor.Ambarus at microchip.com

From: Tudor Ambarus <[email protected]>

The Special Function Registers (SFR) are present in sam9x5 and sam9x60 too, rename sama5_sfr to at91_sfr.h.

---
 arch/arm/mach-at91/armv7/sama5d4_devices.c                  | 2 +-
 arch/arm/mach-at91/atmel_sfr.c                              | 2 +-
 arch/arm/mach-at91/include/mach/{sama5_sfr.h => at91_sfr.h} | 4 ++--
 board/laird/wb50n/wb50n.c                                   | 2 +-
 drivers/clk/at91/clk-utmi.c                                 | 2 +-
 5 files changed, 6 insertions(+), 6 deletions(-)
 rename arch/arm/mach-at91/include/mach/{sama5_sfr.h => at91_sfr.h} (97%)
arch/arm/mach-at91/armv7/sama5d4_devices.c +1 -1
index 5c693df2ecf0..e68ae9940788 100644
@@ -8,7 +8,7 @@
 #include <asm/io.h>
 #include <asm/arch/at91_common.h>
 #include <asm/arch/clk.h>
-#include <asm/arch/sama5_sfr.h>
+#include <asm/arch/at91_sfr.h>
 #include <asm/arch/sama5d4.h>
 
 char *get_cpu_name()
arch/arm/mach-at91/atmel_sfr.c +1 -1
index 13cfba0ba0c0..b14222460f3a 100644
@@ -7,7 +7,7 @@
 #include <common.h>
 #include <asm/hardware.h>
 #include <asm/io.h>
-#include <asm/arch/sama5_sfr.h>
+#include <asm/arch/at91_sfr.h>
 
 #if defined(CONFIG_SAMA5D2) || defined(CONFIG_SAMA5D4)
 void redirect_int_from_saic_to_aic(void)
arch/arm/mach-at91/include/mach/at91_sfr.h renamed from arch/arm/mach-at91/include/mach/sama5_sfr.h +2 -2
similarity index 97%
rename from arch/arm/mach-at91/include/mach/sama5_sfr.h
rename to arch/arm/mach-at91/include/mach/at91_sfr.h
index f9c412f9989a..dc259055cff6 100644
@@ -6,8 +6,8 @@
  *		      Bo Shen <[email protected]>
  */
 
-#ifndef __SAMA5_SFR_H
-#define __SAMA5_SFR_H
+#ifndef __AT91_SFR_H
+#define __AT91_SFR_H
 
 struct atmel_sfr {
 	u32 reserved1;	/* 0x00 */
board/laird/wb50n/wb50n.c +1 -1
index ab1dbcd879ae..13563abb49ef 100644
@@ -4,7 +4,7 @@
 
 #include <common.h>
 #include <asm/io.h>
-#include <asm/arch/sama5_sfr.h>
+#include <asm/arch/at91_sfr.h>
 #include <asm/arch/sama5d3_smc.h>
 #include <asm/arch/at91_common.h>
 #include <asm/arch/at91_pmc.h>
drivers/clk/at91/clk-utmi.c +1 -1
index e8506099fd32..18af0bfeaad1 100644
@@ -10,7 +10,7 @@
 #include <syscon.h>
 #include <linux/io.h>
 #include <mach/at91_pmc.h>
-#include <mach/sama5_sfr.h>
+#include <mach/at91_sfr.h>
 #include "pmc.h"
 
 /*
Signature · 1 line
2.9.5
#7 lore raw

PATCH 7/12 ARM: at91: Add SFR definitions

In reply to Tudor.Ambarus at microchip.com

From: Tudor Ambarus <[email protected]>

sama5's SFR has at offset 0x04 the DDR Configuration Register, while sam9x60's SFR contains the EBI Chip Select Register. Add a union to reconcile both boards.

---
 arch/arm/mach-at91/include/mach/at91_sfr.h | 48 ++++++++++++++++++++++++++++--
 1 file changed, 45 insertions(+), 3 deletions(-)
arch/arm/mach-at91/include/mach/at91_sfr.h +45 -3
index dc259055cff6..0300c336dd81 100644
@@ -11,7 +11,10 @@
 
 struct atmel_sfr {
 	u32 reserved1;	/* 0x00 */
-	u32 ddrcfg;	/* 0x04: DDR Configuration Register */
+	union {
+		u32 ddrcfg;	/* 0x04: DDR Configuration Register */
+		u32 ebicsa;	/* 0x04: EBI Chip Select Register */
+	};
 	u32 reserved2;	/* 0x08 */
 	u32 reserved3;	/* 0x0c */
 	u32 ohciicr;	/* 0x10: OHCI Interrupt Configuration Register */
@@ -28,7 +31,16 @@ struct atmel_sfr {
 };
 
 /* Register Mapping*/
+#define AT91_SFR_DDRCFG		0x04	/* DDR Configuration Register */
+#define AT91_SFR_CCFG_EBICSA	0x04	/* EBI Chip Select Register */
+/* 0x08 ~ 0x0c: Reserved */
+#define AT91_SFR_OHCIICR	0x10	/* OHCI INT Configuration Register */
+#define AT91_SFR_OHCIISR	0x14	/* OHCI INT Status Register */
 #define AT91_SFR_UTMICKTRIM	0x30	/* UTMI Clock Trimming Register */
+#define AT91_SFR_UTMISWAP	0x3c	/* UTMI DP/DM Pin Swapping Register */
+#define AT91_SFR_LS		0x7c	/* Light Sleep Register */
+#define AT91_SFR_I2SCLKSEL	0x90	/* I2SC Register */
+#define AT91_SFR_WPMR		0xe4	/* Write Protection Mode Register */
 
 /* Bit field in DDRCFG */
 #define ATMEL_SFR_DDRCFG_FDQIEN		0x00010000
@@ -58,9 +70,39 @@ struct atmel_sfr {
 #define AT91_SFR_EBICFG_SCH1_OFF		(0x0 << 12)
 #define AT91_SFR_EBICFG_SCH1_ON			(0x1 << 12)
 
-#define AT91_UTMICKTRIM_FREQ		GENMASK(1, 0)
-
 /* Bit field in AICREDIR */
 #define ATMEL_SFR_AICREDIR_NSAIC	0x00000001
 
+/* Bit field in DDRCFG */
+#define ATMEL_SFR_DDRCFG_FDQIEN                0x00010000
+#define ATMEL_SFR_DDRCFG_FDQSIEN       0x00020000
+
+#define AT91_SFR_CCFG_EBI_CSA(cs, val)		((val) << (cs))
+#define AT91_SFR_CCFG_EBI_DBPUC			BIT(8)
+#define AT91_SFR_CCFG_EBI_DBPDC			BIT(9)
+#define AT91_SFR_CCFG_EBI_DRIVE_SAM9X60		BIT(16)
+#define AT91_SFR_CCFG_EBI_DRIVE			BIT(17)
+#define AT91_SFR_CCFG_DQIEN_F			BIT(20)
+#define AT91_SFR_CCFG_NFD0_ON_D16		BIT(24)
+#define AT91_SFR_CCFG_DDR_MP_EN			BIT(25)
+
+#define AT91_SFR_OHCIICR_RES(x)			BIT(x)
+#define AT91_SFR_OHCIICR_ARIE			BIT(4)
+#define AT91_SFR_OHCIICR_APPSTART		BIT(5)
+#define AT91_SFR_OHCIICR_USB_SUSP(x)		BIT(8 + (x))
+#define AT91_SFR_OHCIICR_UDPPUDIS		BIT(23)
+#define AT91_OHCIICR_USB_SUSPEND		GENMASK(10, 8)
+
+#define AT91_SFR_OHCIISR_RIS(x)			BIT(x)
+
+#define AT91_UTMICKTRIM_FREQ			GENMASK(1, 0)
+
+#define AT91_SFR_UTMISWAP_PORT(x)		BIT(x)
+
+#define AT91_SFR_LS_VALUE(x)			BIT(x)
+#define AT91_SFR_LS_MEM_POWER_GATING_ULP1_EN	BIT(16)
+
+#define AT91_SFR_WPMR_WPEN			BIT(0)
+#define AT91_SFR_WPMR_WPKEY_MASK		GENMASK(31, 8)
+
 #endif
Signature · 1 line
2.9.5
#8 lore raw

PATCH 8/12 board: sam9x60ek: Add NAND flash support

In reply to Tudor.Ambarus at microchip.com

From: Tudor Ambarus <[email protected]>

- EBI Chip Select Register is now in SFR,
- the pins are set to default values,
- timings are matching MT29F4G08BABWP's nand flash requirements.

---
 board/atmel/sam9x60ek/sam9x60ek.c | 61 +++++++++++++++++++++++++++++++++++++++
 include/configs/sam9x60ek.h       | 28 ++++++++++++++++++
 2 files changed, 89 insertions(+)
board/atmel/sam9x60ek/sam9x60ek.c +61 -0
index 62938741ddd6..e352afc67ed3 100644
@@ -7,8 +7,10 @@
 
 #include <common.h>
 #include <asm/io.h>
+#include <asm/arch/at91sam9_smc.h>
 #include <asm/arch/at91_common.h>
 #include <asm/arch/at91_rstc.h>
+#include <asm/arch/at91_sfr.h>
 #include <asm/arch/clk.h>
 #include <asm/arch/gpio.h>
 #include <debug_uart.h>
@@ -18,6 +20,62 @@ DECLARE_GLOBAL_DATA_PTR;
 
 void at91_prepare_cpu_var(void);
 
+#ifdef CONFIG_CMD_NAND
+static void sam9x60ek_nand_hw_init(void)
+{
+	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+	struct atmel_sfr *sfr = (struct atmel_sfr *)ATMEL_BASE_SFR;
+	unsigned int csa;
+
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 0, 1);	/* NAND OE */
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 1, 1);	/* NAND WE */
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 2, 0);	/* NAND ALE */
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 3, 0);	/* NAND CLE */
+	/* Enable NandFlash */
+	at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+	/* Configure RDY/BSY */
+	at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 6, 1);
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 7, 1);
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 8, 1);
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 9, 1);
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 10, 1);
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 11, 1);
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 12, 1);
+	at91_pio3_set_a_periph(AT91_PIO_PORTD, 13, 1);
+
+	at91_periph_clk_enable(ATMEL_ID_PIOD);
+
+	/* Enable CS3 */
+	csa = readl(&sfr->ebicsa);
+	csa |= AT91_SFR_CCFG_EBI_CSA(3, 1) | AT91_SFR_CCFG_NFD0_ON_D16;
+
+	/* Configure IO drive */
+	csa &= ~AT91_SFR_CCFG_EBI_DRIVE_SAM9X60;
+
+	writel(csa, &sfr->ebicsa);
+
+	/* Configure SMC CS3 for NAND/SmartMedia */
+	writel(AT91_SMC_SETUP_NWE(4), &smc->cs[3].setup);
+
+	writel(AT91_SMC_PULSE_NWE(10) | AT91_SMC_PULSE_NCS_WR(20) |
+	       AT91_SMC_PULSE_NRD(10) | AT91_SMC_PULSE_NCS_RD(20),
+	       &smc->cs[3].pulse);
+
+	writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20),
+	       &smc->cs[3].cycle);
+
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+#ifdef CONFIG_SYS_NAND_DBW_16
+	       AT91_SMC_MODE_DBW_16 |
+#else /* CONFIG_SYS_NAND_DBW_8 */
+	       AT91_SMC_MODE_DBW_8 |
+#endif
+	       AT91_SMC_MODE_TDF | AT91_SMC_MODE_TDF_CYCLE(15),
+	       &smc->cs[3].mode);
+}
+#endif
+
 #ifdef CONFIG_BOARD_LATE_INIT
 int board_late_init(void)
 {
@@ -48,6 +106,9 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
+#ifdef CONFIG_CMD_NAND
+	sam9x60ek_nand_hw_init();
+#endif
 	return 0;
 }
 
include/configs/sam9x60ek.h +28 -0
index b778bd8e83eb..dbcbce3a2b80 100644
@@ -42,6 +42,26 @@
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
 
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+#define CONFIG_SYS_NAND_MASK_ALE	BIT(21)
+#define CONFIG_SYS_NAND_MASK_CLE	BIT(22)
+#define CONFIG_SYS_NAND_ENABLE_PIN	AT91_PIN_PD4
+#define CONFIG_SYS_NAND_READY_PIN	AT91_PIN_PD5
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+#define CONFIG_MTD_DEVICE
+#endif
+
+/* PMECC & PMERRLOC */
+#define CONFIG_ATMEL_NAND_HWECC
+#define CONFIG_ATMEL_NAND_HW_PMECC
+#define CONFIG_PMECC_CAP		8
+#define CONFIG_PMECC_SECTOR_SIZE	512
+
 #define CONFIG_SYS_LOAD_ADDR		0x22000000	/* load address */
 
 #ifdef CONFIG_SD_BOOT
@@ -50,6 +70,14 @@
 			"fatload mmc 0:1 0x21000000 at91-sam9x60ek.dtb;" \
 			"fatload mmc 0:1 0x22000000 zImage;" \
 			"bootz 0x22000000 - 0x21000000"
+
+#elif defined(CONFIG_NAND_BOOT)
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_OFFSET_REDUND	0x100000
+#define CONFIG_BOOTCOMMAND	"nand read " \
+				"0x22000000 0x200000 0x600000; " \
+				"nand read 0x21000000 0x180000 0x20000; " \
+				"bootz 0x22000000 - 0x21000000"
 #endif
 
 /*
Signature · 1 line
2.9.5
#9 lore raw

PATCH 9/12 configs: Add sam9x60ek_nandflash_defconfig

In reply to Tudor.Ambarus at microchip.com

From: Tudor Ambarus <[email protected]>

Boot from nand flash.

---
 configs/sam9x60ek_nandflash_defconfig | 51 +++++++++++++++++++++++++++++++++++
 1 file changed, 51 insertions(+)
 create mode 100644 configs/sam9x60ek_nandflash_defconfig
configs/sam9x60ek_nandflash_defconfig new file +51 -0
new file mode 100644
index 000000000000..4858539edeec
@@ -0,0 +1,51 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_SYS_TEXT_BASE=0x23f00000
+CONFIG_TARGET_SAM9X60EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_NR_DRAM_BANKS=8
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEBUG_UART=y
+CONFIG_FIT=y
+CONFIG_NAND_BOOT=y
+CONFIG_BOOTDELAY=3
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256k(env_redundant),256k(env),512k(dtb),6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=6 root=ubi0:rootfs rw"
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="U-Boot> "
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_NAND_TRIMFFS=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="sam9x60ek"
+CONFIG_ENV_IS_IN_NAND=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_TIMER=y
+CONFIG_ATMEL_PIT_TIMER=y
+CONFIG_OF_LIBFDT_OVERLAY=y
Signature · 1 line
2.9.5
#10 lore raw

PATCH 10/12 configs: sam9x60ek: Add QSPI_BOOT defines

In reply to Tudor.Ambarus at microchip.com

From: Tudor Ambarus <[email protected]>

Cope with the offsets defined at:
https://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections/demo_nandflash_map_lnx4sam6x.png

The environment starts at 0x140000 and it's of size 0x20000. The device tree starts at 0x180000 and it's of size 0x80000. The zImage starts at 0x200000 and it's of size 0x600000.

---
 include/configs/sam9x60ek.h | 7 +++++++
 1 file changed, 7 insertions(+)
include/configs/sam9x60ek.h +7 -0
index dbcbce3a2b80..5f89ae4a511a 100644
@@ -78,6 +78,13 @@
 				"0x22000000 0x200000 0x600000; " \
 				"nand read 0x21000000 0x180000 0x20000; " \
 				"bootz 0x22000000 - 0x21000000"
+
+#elif defined(CONFIG_QSPI_BOOT)
+/* bootstrap + u-boot + env + linux in SPI NOR flash */
+#define CONFIG_BOOTCOMMAND	"sf probe 0; "					\
+				"sf read 0x21000000 0x180000 0x80000; "		\
+				"sf read 0x22000000 0x200000 0x600000; "	\
+				"bootz 0x22000000 - 0x21000000"
 #endif
 
 /*
Signature · 1 line
2.9.5
#11 lore raw

PATCH 11/12 ARM: dts: at91: sam9x60ek: Enable qspi node

In reply to Tudor.Ambarus at microchip.com

From: Tudor Ambarus <[email protected]>

The sam9x60 qspi controller uses 2 clocks, one for the peripheral register access, the other for the qspi core and phy. Both are mandatory.

Enable the qspi node together with the SST26VF064B qspi nor flash memory. Booting from the QSPI NOR flash is now possible.

---
 arch/arm/dts/sam9x60.dtsi          | 29 +++++++++++++++++++++++++++++
 arch/arm/dts/sam9x60ek-u-boot.dtsi | 28 ++++++++++++++++++++++++++++
 arch/arm/dts/sam9x60ek.dts         | 31 +++++++++++++++++++++++++++++++
 3 files changed, 88 insertions(+)
arch/arm/dts/sam9x60.dtsi +29 -0
index a66d0a278a87..9c16ba1e6a87 100644
@@ -22,6 +22,7 @@
 		serial0 = &dbgu;
 		gpio0 = &pioA;
 		gpio1 = &pioB;
+		spi0 = &qspi;
 	};
 
 	clocks {
@@ -60,6 +61,17 @@
 			#size-cells = <1>;
 			ranges;
 
+			qspi: spi at f0014000 {
+				compatible = "microchip,sam9x60-qspi";
+				reg = <0xf0014000 0x100>, <0x70000000 0x10000000>;
+				reg-names = "qspi_base", "qspi_mmap";
+				clocks =  <&qspi_clk>, <&qspick>;
+				clock-names = "pclk", "qspick";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
 			macb0: ethernet at f802c000 {
 				compatible = "cdns,sam9x60-macb", "cdns,macb";
 				reg = <0xf802c000 0x100>;
@@ -172,6 +184,18 @@
 					atmel,clk-divisors = <1 2 4 6>;
 				};
 
+				system: systemck {
+					compatible = "atmel,at91rm9200-clk-system";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					qspick: qspick {
+						#clock-cells = <0>;
+						reg = <19>;
+						clocks = <&mck>;
+					};
+				};
+
 				periph: periphck {
 					compatible = "microchip,sam9x60-clk-peripheral";
 					#address-cells = <1>;
@@ -202,6 +226,11 @@
 						#clock-cells = <0>;
 						reg = <24>;
 					};
+
+					qspi_clk: qspi_clk {
+						#clock-cells = <0>;
+						reg = <35>;
+					};
 				};
 
 				generic: gck {
arch/arm/dts/sam9x60ek-u-boot.dtsi +28 -0
index 68e220926e5e..93cf1262f6fc 100644
@@ -31,6 +31,10 @@
 	u-boot,dm-pre-reloc;
 };
 
+&qspi {
+	u-boot,dm-pre-reloc;
+};
+
 &pinctrl_dbgu {
 	u-boot,dm-pre-reloc;
 };
@@ -39,10 +43,18 @@
 	u-boot,dm-pre-reloc;
 };
 
+&pinctrl_qspi {
+	u-boot,dm-pre-reloc;
+};
+
 &pioA {
 	u-boot,dm-pre-reloc;
 };
 
+&pioB {
+	u-boot,dm-pre-reloc;
+};
+
 &pmc {
 	u-boot,dm-pre-reloc;
 };
@@ -59,6 +71,14 @@
 	u-boot,dm-pre-reloc;
 };
 
+&system {
+	u-boot,dm-pre-reloc;
+};
+
+&qspick {
+	u-boot,dm-pre-reloc;
+};
+
 &periph {
 	u-boot,dm-pre-reloc;
 };
@@ -67,6 +87,10 @@
 	u-boot,dm-pre-reloc;
 };
 
+&pioB_clk {
+	u-boot,dm-pre-reloc;
+};
+
 &sdhci0_clk {
 	u-boot,dm-pre-reloc;
 };
@@ -75,6 +99,10 @@
 	u-boot,dm-pre-reloc;
 };
 
+&qspi_clk {
+	u-boot,dm-pre-reloc;
+};
+
 &generic {
 	u-boot,dm-pre-reloc;
 };
arch/arm/dts/sam9x60ek.dts +31 -0
index 6fe9f19f0bc7..63904272f08f 100644
@@ -16,6 +16,37 @@
 	chosen {
 		stdout-path = &dbgu;
 	};
+
+	ahb {
+		apb {
+			qspi: spi at f0014000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_qspi>;
+				status = "okay";
+
+				nor_flash: sst26vf064 at 0 {
+					compatible = "spi-flash";
+					reg = <0>;
+					spi-max-frequency = <80000000>;
+					spi-rx-bus-width = <4>;
+					spi-tx-bus-width = <4>;
+				};
+			};
+
+			pinctrl {
+					pinctrl_qspi: qspi {
+						atmel,pins =
+							<AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOB 20 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOB 21 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+							 AT91_PIOB 22 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+							 AT91_PIOB 23 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+							 AT91_PIOB 24 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+					};
+
+			};
+		};
+	};
 };
 
 &macb0 {
Signature · 1 line
2.9.5
#12 lore raw

PATCH 12/12 configs: Add sam9x60ek_qspiflash_defconfig

In reply to Tudor.Ambarus at microchip.com

From: Tudor Ambarus <[email protected]>

Boot from QSPI nor flash.

The at91bootstrap, u-boot, u-boot env redundant, u-boot env, device tree and kernel will reside in the QSPI nor flash. The rootfs will reside in the NAND flash.

---
 configs/sam9x60ek_qspiflash_defconfig | 73 +++++++++++++++++++++++++++++++++++
 1 file changed, 73 insertions(+)
 create mode 100644 configs/sam9x60ek_qspiflash_defconfig
configs/sam9x60ek_qspiflash_defconfig new file +73 -0
new file mode 100644
index 000000000000..8e3bf5e4ede6
@@ -0,0 +1,73 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_SYS_TEXT_BASE=0x23f00000
+CONFIG_TARGET_SAM9X60EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_NR_DRAM_BANKS=8
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_ENV_SECT_SIZE=0x1000
+CONFIG_DEBUG_UART=y
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_FIT=y
+CONFIG_QSPI_BOOT=y
+CONFIG_BOOTDELAY=3
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256k(env_redundant),256k(env),512k(dtb),6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=12 root=ubi0:rootfs rw"
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="U-Boot> "
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_NAND_TRIMFFS=y
+CONFIG_CMD_SF=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="sam9x60ek"
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=0
+CONFIG_USE_ENV_SPI_CS=y
+CONFIG_ENV_SPI_CS=0
+CONFIG_USE_ENV_SPI_MAX_HZ=y
+CONFIG_ENV_SPI_MAX_HZ=50000000
+CONFIG_USE_ENV_SPI_MODE=y
+CONFIG_ENV_SPI_MODE=0x0
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_QSPI=y
+CONFIG_TIMER=y
+CONFIG_ATMEL_PIT_TIMER=y
+CONFIG_OF_LIBFDT_OVERLAY=y
Signature · 1 line
2.9.5