drm: sun8i-ui/vi: Fix layer zpos change/atomic modesetting
Subsystems (5)
PATCH 1/1 drm: sun8i-ui/vi: Fix layer zpos change/atomic modesetting
From: Ondrej Jirman <[email protected]>
There are various issues that this re-work of sun8i_[uv]i_layer_enable function fixes:
- Make sure that we re-initialize zpos on reset
- Minimize register updates by doing them only when state changes
- Fix issue where DE pipe might get disabled even if it is no longer used by the layer that's currently calling sun8i_ui_layer_enable
- .atomic_disable callback is not really needed because .atomic_update can do the disable too, so drop the duplicate code
--- drivers/gpu/drm/sun4i/sun8i_ui_layer.c | 112 ++++++++++++++++--------- drivers/gpu/drm/sun4i/sun8i_vi_layer.c | 112 ++++++++++++++++--------- 2 files changed, 142 insertions(+), 82 deletions(-)
drivers/gpu/drm/sun4i/sun8i_ui_layer.c +71 -41
@@ -24,10 +24,11 @@#include "sun8i_ui_scaler.h" static void sun8i_ui_layer_enable (struct sun8i_mixer *mixer,int channel, -int overlay,bool enable,unsigned int zpos, -unsigned int old_zpos) +int overlay,bool was_enabled,bool enable, +unsigned int zpos,unsigned int old_zpos) {u32 val, bld_base, ch_base; +unsigned int old_pipe_ch; bld_base =sun8i_blender_base (mixer); ch_base =sun8i_channel_base (mixer, channel);
@@ -35,28 +36,57 @@ static void sun8i_ui_layer_enable(struct sun8i_mixer *mixer, int channel,DRM_DEBUG_DRIVER ("%sabling channel %d overlay %d\n" , enable ?"En" :"Dis" , channel, overlay); -if (enable) - val =SUN8I_MIXER_CHAN_UI_LAYER_ATTR_EN ; -else - val =0 ; +if (!was_enabled != !enable) { + val = enable ?SUN8I_MIXER_CHAN_UI_LAYER_ATTR_EN :0 ; -regmap_update_bits (mixer->engine.regs, -SUN8I_MIXER_CHAN_UI_LAYER_ATTR (ch_base, overlay), -SUN8I_MIXER_CHAN_UI_LAYER_ATTR_EN , val); - -if (!enable || zpos != old_zpos) {regmap_update_bits (mixer->engine.regs, -SUN8I_MIXER_BLEND_PIPE_CTL (bld_base), -SUN8I_MIXER_BLEND_PIPE_CTL_EN (old_zpos), -0 ); +SUN8I_MIXER_CHAN_UI_LAYER_ATTR (ch_base, overlay), +SUN8I_MIXER_CHAN_UI_LAYER_ATTR_EN , val); + } -regmap_update_bits (mixer->engine.regs, +/* +* If this layer was enabled and is being disabled or if it is +* enabled and just changing zpos, clear the old route, if it is +* still configured to this layer in HW. +*/ +if ((was_enabled && !enable) || (enable && zpos != old_zpos)) { +/* get channel the pipe for old_zpos is routed to from the HW */ +regmap_read (mixer->engine.regs,SUN8I_MIXER_BLEND_ROUTE (bld_base), -SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (old_zpos), -0 ); + &old_pipe_ch); + old_pipe_ch &=SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (old_zpos); + old_pipe_ch >>=SUN8I_MIXER_BLEND_ROUTE_PIPE_SHIFT (old_zpos); + +/* +* Check that pipe for old_zpos is still routed to our layer, +* and clear/disable it if it is. +*/ + +if (old_pipe_ch == channel) { +DRM_DEBUG_DRIVER ("chan=%d en=%d->%d zpos=%d->%d\n" , + channel, was_enabled, enable, old_zpos, zpos); + +DRM_DEBUG_DRIVER (" disable pipe %d\n" , old_zpos); + +regmap_update_bits (mixer->engine.regs, +SUN8I_MIXER_BLEND_ROUTE (bld_base), +SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (old_zpos), +0 ); + +regmap_update_bits (mixer->engine.regs, +SUN8I_MIXER_BLEND_PIPE_CTL (bld_base), +SUN8I_MIXER_BLEND_PIPE_CTL_EN (old_zpos), +0 ); + } } -if (enable) { +/* +* If enabling this layer or changin zpos, set route to this layer. +*/ +if ((enable && !was_enabled) || (enable && zpos != old_zpos)) { +DRM_DEBUG_DRIVER ("chan=%d en=%d->%d zpos=%d->%d\n" , + channel, was_enabled, enable, old_zpos, zpos); + val =SUN8I_MIXER_BLEND_PIPE_CTL_EN (zpos); regmap_update_bits(mixer->engine.regs,
@@ -69,6 +99,8 @@ static void sun8i_ui_layer_enable(struct sun8i_mixer *mixer, int channel,SUN8I_MIXER_BLEND_ROUTE (bld_base),SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (zpos), val); + +DRM_DEBUG_DRIVER (" enable pipe %d <- ch %d\n" , zpos, channel); } }
@@ -261,45 +293,43 @@ static int sun8i_ui_layer_atomic_check(struct drm_plane *plane, true, true); } -static void sun8i_ui_layer_atomic_disable (struct drm_plane *plane, -struct drm_plane_state *old_state) +static void sun8i_ui_layer_atomic_update (struct drm_plane *plane, +struct drm_plane_state *old_state) {struct sun8i_ui_layer *layer =plane_to_sun8i_ui_layer (plane); +unsigned int zpos = plane->state->normalized_zpos;unsigned int old_zpos = old_state->normalized_zpos;struct sun8i_mixer *mixer = layer->mixer; +bool was_enabled = old_state->crtc && old_state->visible; +bool enable = plane->state->crtc && plane->state->visible; -sun8i_ui_layer_enable (mixer, layer->channel, layer->overlay, false,0 , - old_zpos); +if (enable) { +sun8i_ui_layer_update_coord (mixer, layer->channel, + layer->overlay, plane, zpos); +sun8i_ui_layer_update_formats (mixer, layer->channel, + layer->overlay, plane); +sun8i_ui_layer_update_buffer (mixer, layer->channel, + layer->overlay, plane); + } + +sun8i_ui_layer_enable (mixer, layer->channel, layer->overlay, + was_enabled, enable, zpos, old_zpos); } -static void sun8i_ui_layer_atomic_update (struct drm_plane *plane, -struct drm_plane_state *old_state) +void sun8i_ui_layer_plane_reset (struct drm_plane *plane) {struct sun8i_ui_layer *layer =plane_to_sun8i_ui_layer (plane); -unsigned int zpos = plane->state->normalized_zpos; -unsigned int old_zpos = old_state->normalized_zpos; -struct sun8i_mixer *mixer = layer->mixer; -if (!plane->state->visible) { -sun8i_ui_layer_enable (mixer, layer->channel, - layer->overlay, false,0 , old_zpos); +drm_atomic_helper_plane_reset (plane); +if (!plane->state)return ; - } -sun8i_ui_layer_update_coord (mixer, layer->channel, - layer->overlay, plane, zpos); -sun8i_ui_layer_update_formats (mixer, layer->channel, - layer->overlay, plane); -sun8i_ui_layer_update_buffer (mixer, layer->channel, - layer->overlay, plane); -sun8i_ui_layer_enable (mixer, layer->channel, layer->overlay, - true, zpos, old_zpos); + plane->state->zpos = layer->channel; }static struct drm_plane_helper_funcs sun8i_ui_layer_helper_funcs = { .prepare_fb = drm_gem_fb_prepare_fb, .atomic_check = sun8i_ui_layer_atomic_check, - .atomic_disable = sun8i_ui_layer_atomic_disable, .atomic_update = sun8i_ui_layer_atomic_update, };
@@ -308,7 +338,7 @@ static const struct drm_plane_funcs sun8i_ui_layer_funcs = { .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state, .destroy = drm_plane_cleanup, .disable_plane = drm_atomic_helper_disable_plane, - .reset = drm_atomic_helper_plane_reset, + .reset = sun8i_ui_layer_plane_reset, .update_plane = drm_atomic_helper_update_plane, };
drivers/gpu/drm/sun4i/sun8i_vi_layer.c +71 -41
167 lines not on this page · raw message
Signature · 1 line
2.23.0
Quoted 11 lines · megous hlavni
From: Ondrej Jirman <[email protected]>
There are various issues that this re-work of sun8i_[uv]i_layer_enable function fixes:
- Make sure that we re-initialize zpos on reset
- Minimize register updates by doing them only when state changes
- Fix issue where DE pipe might get disabled even if it is no longer used by the layer that's currently callingsun8i_ui_layer_enable
- .atomic_disable callback is not really needed because .atomic_update can do the disable too, so drop the duplicate code
See more discussion here:
https://groups.google.com/d/msg/linux-sunxi/9A7ukdtvNpM/2Z2bAhA9AwAJ
o.
Quoted 361 lines
Signed-off-by Ondrej Jirman <[email protected]>--- drivers/gpu/drm/sun4i/sun8i_ui_layer.c | 112 ++++++++++++++++--------- drivers/gpu/drm/sun4i/sun8i_vi_layer.c | 112 ++++++++++++++++--------- 2 files changed, 142 insertions(+), 82 deletions(-)drivers/gpu/drm/sun4i/sun8i_ui_layer.c +71
-41@@ -24,10 +24,11 @@#include "sun8i_ui_scaler.h" static void sun8i_ui_layer_enable (struct sun8i_mixer *mixer,int channel, -int overlay,bool enable,unsigned int zpos, -unsigned int old_zpos) +int overlay,bool was_enabled,bool enable, +unsigned int zpos,unsigned int old_zpos) {u32 val, bld_base, ch_base; +unsigned int old_pipe_ch; bld_base =sun8i_blender_base (mixer); ch_base =sun8i_channel_base (mixer, channel);@@ -35,28 +36,57 @@ static void sun8i_ui_layer_enable(struct sun8i_mixer *mixer, int channel,DRM_DEBUG_DRIVER ("%sabling channel %d overlay %d\n" , enable ?"En" :"Dis" , channel, overlay); -if (enable) - val =SUN8I_MIXER_CHAN_UI_LAYER_ATTR_EN ; -else - val =0 ; +if (!was_enabled != !enable) { + val = enable ?SUN8I_MIXER_CHAN_UI_LAYER_ATTR_EN :0 ; -regmap_update_bits (mixer->engine.regs, -SUN8I_MIXER_CHAN_UI_LAYER_ATTR (ch_base, overlay), -SUN8I_MIXER_CHAN_UI_LAYER_ATTR_EN , val); - -if (!enable || zpos != old_zpos) {regmap_update_bits (mixer->engine.regs, -SUN8I_MIXER_BLEND_PIPE_CTL (bld_base), -SUN8I_MIXER_BLEND_PIPE_CTL_EN (old_zpos), -0 ); +SUN8I_MIXER_CHAN_UI_LAYER_ATTR (ch_base, overlay), +SUN8I_MIXER_CHAN_UI_LAYER_ATTR_EN , val); + } -regmap_update_bits (mixer->engine.regs, +/* +* If this layer was enabled and is being disabled or if it is +* enabled and just changing zpos, clear the old route, if it is +* still configured to this layer in HW. +*/ +if ((was_enabled && !enable) || (enable && zpos != old_zpos)) { +/* get channel the pipe for old_zpos is routed to from the HW */ +regmap_read (mixer->engine.regs,SUN8I_MIXER_BLEND_ROUTE (bld_base), -SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (old_zpos), -0 ); + &old_pipe_ch); + old_pipe_ch &=SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (old_zpos); + old_pipe_ch >>=SUN8I_MIXER_BLEND_ROUTE_PIPE_SHIFT (old_zpos); + +/* +* Check that pipe for old_zpos is still routed to our layer, +* and clear/disable it if it is. +*/ + +if (old_pipe_ch == channel) { +DRM_DEBUG_DRIVER ("chan=%d en=%d->%d zpos=%d->%d\n" , + channel, was_enabled, enable, old_zpos, zpos); + +DRM_DEBUG_DRIVER (" disable pipe %d\n" , old_zpos); + +regmap_update_bits (mixer->engine.regs, +SUN8I_MIXER_BLEND_ROUTE (bld_base), +SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (old_zpos), +0 ); + +regmap_update_bits (mixer->engine.regs, +SUN8I_MIXER_BLEND_PIPE_CTL (bld_base), +SUN8I_MIXER_BLEND_PIPE_CTL_EN (old_zpos), +0 ); + } } -if (enable) { +/* +* If enabling this layer or changin zpos, set route to this layer. +*/ +if ((enable && !was_enabled) || (enable && zpos != old_zpos)) { +DRM_DEBUG_DRIVER ("chan=%d en=%d->%d zpos=%d->%d\n" , + channel, was_enabled, enable, old_zpos, zpos); + val =SUN8I_MIXER_BLEND_PIPE_CTL_EN (zpos); regmap_update_bits(mixer->engine.regs,@@ -69,6 +99,8 @@ static void sun8i_ui_layer_enable(struct sun8i_mixer *mixer, int channel,SUN8I_MIXER_BLEND_ROUTE (bld_base),SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (zpos), val); + +DRM_DEBUG_DRIVER (" enable pipe %d <- ch %d\n" , zpos, channel); } }@@ -261,45 +293,43 @@ static int sun8i_ui_layer_atomic_check(struct drm_plane *plane, true, true); } -static void sun8i_ui_layer_atomic_disable (struct drm_plane *plane, -struct drm_plane_state *old_state) +static void sun8i_ui_layer_atomic_update (struct drm_plane *plane, +struct drm_plane_state *old_state) {struct sun8i_ui_layer *layer =plane_to_sun8i_ui_layer (plane); +unsigned int zpos = plane->state->normalized_zpos;unsigned int old_zpos = old_state->normalized_zpos;struct sun8i_mixer *mixer = layer->mixer; +bool was_enabled = old_state->crtc && old_state->visible; +bool enable = plane->state->crtc && plane->state->visible; -sun8i_ui_layer_enable (mixer, layer->channel, layer->overlay, false,0 , - old_zpos); +if (enable) { +sun8i_ui_layer_update_coord (mixer, layer->channel, + layer->overlay, plane, zpos); +sun8i_ui_layer_update_formats (mixer, layer->channel, + layer->overlay, plane); +sun8i_ui_layer_update_buffer (mixer, layer->channel, + layer->overlay, plane); + } + +sun8i_ui_layer_enable (mixer, layer->channel, layer->overlay, + was_enabled, enable, zpos, old_zpos); } -static void sun8i_ui_layer_atomic_update (struct drm_plane *plane, -struct drm_plane_state *old_state) +void sun8i_ui_layer_plane_reset (struct drm_plane *plane) {struct sun8i_ui_layer *layer =plane_to_sun8i_ui_layer (plane); -unsigned int zpos = plane->state->normalized_zpos; -unsigned int old_zpos = old_state->normalized_zpos; -struct sun8i_mixer *mixer = layer->mixer; -if (!plane->state->visible) { -sun8i_ui_layer_enable (mixer, layer->channel, - layer->overlay, false,0 , old_zpos); +drm_atomic_helper_plane_reset (plane); +if (!plane->state)return ; - } -sun8i_ui_layer_update_coord (mixer, layer->channel, - layer->overlay, plane, zpos); -sun8i_ui_layer_update_formats (mixer, layer->channel, - layer->overlay, plane); -sun8i_ui_layer_update_buffer (mixer, layer->channel, - layer->overlay, plane); -sun8i_ui_layer_enable (mixer, layer->channel, layer->overlay, - true, zpos, old_zpos); + plane->state->zpos = layer->channel; }static struct drm_plane_helper_funcs sun8i_ui_layer_helper_funcs = { .prepare_fb = drm_gem_fb_prepare_fb, .atomic_check = sun8i_ui_layer_atomic_check, - .atomic_disable = sun8i_ui_layer_atomic_disable, .atomic_update = sun8i_ui_layer_atomic_update, };@@ -308,7 +338,7 @@ static const struct drm_plane_funcs sun8i_ui_layer_funcs = { .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state, .destroy = drm_plane_cleanup, .disable_plane = drm_atomic_helper_disable_plane, - .reset = drm_atomic_helper_plane_reset, + .reset = sun8i_ui_layer_plane_reset, .update_plane = drm_atomic_helper_update_plane, };drivers/gpu/drm/sun4i/sun8i_vi_layer.c +71
-41@@ -18,10 +18,11 @@#include "sun8i_vi_scaler.h" static void sun8i_vi_layer_enable (struct sun8i_mixer *mixer,int channel, -int overlay,bool enable,unsigned int zpos, -unsigned int old_zpos) +int overlay,bool was_enabled,bool enable, +unsigned int zpos,unsigned int old_zpos) {u32 val, bld_base, ch_base; +unsigned int old_pipe_ch; bld_base =sun8i_blender_base (mixer); ch_base =sun8i_channel_base (mixer, channel);@@ -29,28 +30,57 @@ static void sun8i_vi_layer_enable(struct sun8i_mixer *mixer, int channel,DRM_DEBUG_DRIVER ("%sabling VI channel %d overlay %d\n" , enable ?"En" :"Dis" , channel, overlay); -if (enable) - val =SUN8I_MIXER_CHAN_VI_LAYER_ATTR_EN ; -else - val =0 ; - -regmap_update_bits (mixer->engine.regs, -SUN8I_MIXER_CHAN_VI_LAYER_ATTR (ch_base, overlay), -SUN8I_MIXER_CHAN_VI_LAYER_ATTR_EN , val); +if (!was_enabled != !enable) { + val = enable ?SUN8I_MIXER_CHAN_VI_LAYER_ATTR_EN :0 ; -if (!enable || zpos != old_zpos) {regmap_update_bits (mixer->engine.regs, -SUN8I_MIXER_BLEND_PIPE_CTL (bld_base), -SUN8I_MIXER_BLEND_PIPE_CTL_EN (old_zpos), -0 ); +SUN8I_MIXER_CHAN_VI_LAYER_ATTR (ch_base, overlay), +SUN8I_MIXER_CHAN_VI_LAYER_ATTR_EN , val); + } -regmap_update_bits (mixer->engine.regs, +/* +* If this layer was enabled and is being disabled or if it is +* enabled and just changing zpos, clear the old route, if it is +* still configured to this layer in HW. +*/ +if ((was_enabled && !enable) || (enable && zpos != old_zpos)) { +/* get channel the pipe for old_zpos is routed to from the HW */ +regmap_read (mixer->engine.regs,SUN8I_MIXER_BLEND_ROUTE (bld_base), -SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (old_zpos), -0 ); + &old_pipe_ch); + old_pipe_ch &=SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (old_zpos); + old_pipe_ch >>=SUN8I_MIXER_BLEND_ROUTE_PIPE_SHIFT (old_zpos); + +/* +* Check that pipe for old_zpos is still routed to our layer, +* and clear/disable it if it is. +*/ + +if (old_pipe_ch == channel) { +DRM_DEBUG_DRIVER ("chan=%d en=%d->%d zpos=%d->%d\n" , + channel, was_enabled, enable, old_zpos, zpos); + +DRM_DEBUG_DRIVER (" disable pipe %d\n" , old_zpos); + +regmap_update_bits (mixer->engine.regs, +SUN8I_MIXER_BLEND_ROUTE (bld_base), +SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (old_zpos), +0 ); + +regmap_update_bits (mixer->engine.regs, +SUN8I_MIXER_BLEND_PIPE_CTL (bld_base), +SUN8I_MIXER_BLEND_PIPE_CTL_EN (old_zpos), +0 ); + } } -if (enable) { +/* +* If enabling this layer or changin zpos, set route to this layer. +*/ +if ((enable && !was_enabled) || (enable && zpos != old_zpos)) { +DRM_DEBUG_DRIVER ("chan=%d en=%d->%d zpos=%d->%d\n" , + channel, was_enabled, enable, old_zpos, zpos); + val =SUN8I_MIXER_BLEND_PIPE_CTL_EN (zpos); regmap_update_bits(mixer->engine.regs,@@ -63,6 +93,8 @@ static void sun8i_vi_layer_enable(struct sun8i_mixer *mixer, int channel,SUN8I_MIXER_BLEND_ROUTE (bld_base),SUN8I_MIXER_BLEND_ROUTE_PIPE_MSK (zpos), val); + +DRM_DEBUG_DRIVER (" enable pipe %d <- ch %d\n" , zpos, channel); } }@@ -345,45 +377,43 @@ static int sun8i_vi_layer_atomic_check(struct drm_plane *plane, true, true); } -static void sun8i_vi_layer_atomic_disable (struct drm_plane *plane, -struct drm_plane_state *old_state) +static void sun8i_vi_layer_atomic_update (struct drm_plane *plane, +struct drm_plane_state *old_state) {struct sun8i_vi_layer *layer =plane_to_sun8i_vi_layer (plane); +unsigned int zpos = plane->state->normalized_zpos;unsigned int old_zpos = old_state->normalized_zpos;struct sun8i_mixer *mixer = layer->mixer; +bool was_enabled = old_state->crtc && old_state->visible; +bool enable = plane->state->crtc && plane->state->visible; -sun8i_vi_layer_enable (mixer, layer->channel, layer->overlay, false,0 , - old_zpos); +if (enable) { +sun8i_vi_layer_update_coord (mixer, layer->channel, + layer->overlay, plane, zpos); +sun8i_vi_layer_update_formats (mixer, layer->channel, + layer->overlay, plane); +sun8i_vi_layer_update_buffer (mixer, layer->channel, + layer->overlay, plane); + } + +sun8i_vi_layer_enable (mixer, layer->channel, layer->overlay, + was_enabled, enable, zpos, old_zpos); } -static void sun8i_vi_layer_atomic_update (struct drm_plane *plane, -struct drm_plane_state *old_state) +void sun8i_vi_layer_plane_reset (struct drm_plane *plane) {struct sun8i_vi_layer *layer =plane_to_sun8i_vi_layer (plane); -unsigned int zpos = plane->state->normalized_zpos; -unsigned int old_zpos = old_state->normalized_zpos; -struct sun8i_mixer *mixer = layer->mixer; -if (!plane->state->visible) { -sun8i_vi_layer_enable (mixer, layer->channel, - layer->overlay, false,0 , old_zpos); +drm_atomic_helper_plane_reset (plane); +if (!plane->state)return ; - } -sun8i_vi_layer_update_coord (mixer, layer->channel, - layer->overlay, plane, zpos); -sun8i_vi_layer_update_formats (mixer, layer->channel, - layer->overlay, plane); -sun8i_vi_layer_update_buffer (mixer, layer->channel, - layer->overlay, plane); -sun8i_vi_layer_enable (mixer, layer->channel, layer->overlay, - true, zpos, old_zpos); + plane->state->zpos = layer->channel; }static struct drm_plane_helper_funcs sun8i_vi_layer_helper_funcs = { .prepare_fb = drm_gem_fb_prepare_fb, .atomic_check = sun8i_vi_layer_atomic_check, - .atomic_disable = sun8i_vi_layer_atomic_disable, .atomic_update = sun8i_vi_layer_atomic_update, };@@ -392,7 +422,7 @@ static const struct drm_plane_funcs sun8i_vi_layer_funcs = { .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state, .destroy = drm_plane_cleanup, .disable_plane = drm_atomic_helper_disable_plane, - .reset = drm_atomic_helper_plane_reset, + .reset = sun8i_vi_layer_plane_reset, .update_plane = drm_atomic_helper_update_plane, };Signature · 1 line
2.23.0
Maxime Ripard
maintainerHi,
Quoted 5 lines · On Sun, Sep 15, 2019 at 12:03:37AM +0200, [email protected] wrote:
From: Ondrej Jirman <[email protected]>
There are various issues that this re-work of sun8i_[uv]i_layer_enable function fixes:
Quoted 8 lines
- Make sure that we re-initialize zpos on reset
- Minimize register updates by doing them only when state changes
- Fix issue where DE pipe might get disabled even if it is no longer used by the layer that's currently callingsun8i_ui_layer_enable
- .atomic_disable callback is not really needed because .atomic_update can do the disable too, so drop the duplicate codeSigned-off-by Ondrej Jirman <[email protected]>
It looks like these fixes should be in separate patches. Is there any reason it's not the case?
Maxime
Hi,
Quoted 15 lines · Maxime Ripard
Hi,
Quoted 12 lines · On Sun, Sep 15, 2019 at 12:03:37AM +0200, [email protected] wrote:
From: Ondrej Jirman <[email protected]>
There are various issues that this re-work of sun8i_[uv]i_layer_enable function fixes:
- Make sure that we re-initialize zpos on reset
- Minimize register updates by doing them only when state changes
- Fix issue where DE pipe might get disabled even if it is no longer used by the layer that's currently callingsun8i_ui_layer_enable
- .atomic_disable callback is not really needed because .atomic_update can do the disable too, so drop the duplicate code
Quoted 4 lines
Quoted 1 line
Signed-off-by Ondrej Jirman <[email protected]>It looks like these fixes should be in separate patches. Is there any reason it's not the case?
Bullet points just describe the resulting effect/benefits of the change to fix the pipe control register update issue (see the referenced e-mail).
I can maybe split off the first bullet point into a separate patch. But I can't guarantee it will not make the original issue worse, because it might have been hiding the other issue with register updates.
The rest is just a result of the single logical change. It doesn't work individually, it all has the goal of fixing the issue as a whole.
If I were to split it I would have to actually re-implement .atomic_disable callback only to remove it in the next patch. I don't see the benefit.
regards,
o.
Quoted 1 line
Maxime
Maxime Ripard
maintainerQuoted 18 lines · Ondřej Jirman
Hi,
Quoted 15 lines · Maxime Ripard
Hi,
Quoted 12 lines · On Sun, Sep 15, 2019 at 12:03:37AM +0200, [email protected] wrote:
From: Ondrej Jirman <[email protected]>
There are various issues that this re-work of sun8i_[uv]i_layer_enable function fixes:
- Make sure that we re-initialize zpos on reset
- Minimize register updates by doing them only when state changes
- Fix issue where DE pipe might get disabled even if it is no longer used by the layer that's currently callingsun8i_ui_layer_enable
- .atomic_disable callback is not really needed because .atomic_update can do the disable too, so drop the duplicate code
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Signed-off-by Ondrej Jirman <[email protected]>It looks like these fixes should be in separate patches. Is there any reason it's not the case?
Bullet points just describe the resulting effect/benefits of the change to fix the pipe control register update issue (see the referenced e-mail).
It's definitely ok to have multiple patches needed to address a single perceived issue.
A commit is not about what you're fixing but what you're changing. And the fact that you have tha bullet list in the first place proves that you have multiple logical changes in your patch.
And even then, your commit log mentions that you're fixing multiple issues (without explaining them).
Quoted 9 lines
I can maybe split off the first bullet point into a separate patch. But I can't guarantee it will not make the original issue worse, because it might have been hiding the other issue with register updates.
The rest is just a result of the single logical change. It doesn't work individually, it all has the goal of fixing the issue as a whole.
If I were to split it I would have to actually re-implement .atomic_disable callback only to remove it in the next patch. I don't see the benefit.
Your commit log says that you remove atomic_disable. Why would you remove it, to add it back, to remove it again?
Maxime
Quoted 21 lines · Maxime Ripard
Quoted 20 lines · Ondřej Jirman
Hi,
Quoted 17 lines · Maxime Ripard
Hi,
Quoted 13 lines · On Sun, Sep 15, 2019 at 12:03:37AM +0200, [email protected] wrote:
From: Ondrej Jirman <[email protected]>
There are various issues that this re-work of sun8i_[uv]i_layer_enable function fixes:
- Make sure that we re-initialize zpos on reset
- Minimize register updates by doing them only when state changes
- Fix issue where DE pipe might get disabled even if it is no longer used by the layer that's currently callingsun8i_ui_layer_enable
- .atomic_disable callback is not really needed because .atomic_update can do the disable too, so drop the duplicate codeSigned-off-by Ondrej Jirman <[email protected]>
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
It looks like these fixes should be in separate patches. Is there any reason it's not the case?
Bullet points just describe the resulting effect/benefits of the change to fix the pipe control register update issue (see the referenced e-mail).
It's definitely ok to have multiple patches needed to address a single perceived issue.
Yes, but I can't simply split the patch. In order for each change to work on its own, they'd have to be done differently than the final result.
I wouldn't mind at all if it was just a simple splitting, but you're asking for too much work, this time, for no benefit that I can see.
Quoted 6 lines
A commit is not about what you're fixing but what you're changing. And the fact that you have tha bullet list in the first place proves that you have multiple logical changes in your patch.
And even then, your commit log mentions that you're fixing multiple issues (without explaining them).
I can reword the commit message if that helps, and skip the bullet list if it is confusing. There's a single core issue and that is that the driver doesn't update the pipe/channel configuration correctly leading to disabling of arbitrary layers (not even those being updated - update of UI layer may disable VI layer as a side effect for example) at wrong times. And only changes necessary to debug/fix this are included.
I may try generating a nicer patch with a different diff options, if it makes it more readable for review.
Quoted 4 lines
Quoted 4 lines
I can maybe split off the first bullet point into a separate patch. But I can't guarantee it will not make the original issue worse, because it might have been hiding the other issue with register updates.
Quoted 8 lines
Quoted 5 lines
The rest is just a result of the single logical change. It doesn't work individually, it all has the goal of fixing the issue as a whole.
If I were to split it I would have to actually re-implement .atomic_disable callback only to remove it in the next patch. I don't see the benefit.
Your commit log says that you remove
atomic_disable. Why would you remove it, to add it back, to remove it again?
Because if I remove it I need to re-implement the functionality in the update callback. The core will change what is called based on presence of callbacks. It's not a simple removal.
If I first implement the new sun8i_[uv]i_layer_enable and update callback, keeping a disable callback would not work, because the new update callback will only work if disable callback is not defined (because it it is, then the drm core will not call the update callback in all cases that I need).
regards,
o.
Quoted 8 lines
Maxime
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 44 lines · megous hlavni
Quoted 21 lines · Maxime Ripard
Quoted 20 lines · Ondřej Jirman
Hi,
Quoted 17 lines · Maxime Ripard
Hi,
Quoted 13 lines · On Sun, Sep 15, 2019 at 12:03:37AM +0200, [email protected] wrote:
From: Ondrej Jirman <[email protected]>
There are various issues that this re-work of sun8i_[uv]i_layer_enable function fixes:
- Make sure that we re-initialize zpos on reset
- Minimize register updates by doing them only when state changes
- Fix issue where DE pipe might get disabled even if it is no longer used by the layer that's currently callingsun8i_ui_layer_enable
- .atomic_disable callback is not really needed because .atomic_update can do the disable too, so drop the duplicate codeSigned-off-by Ondrej Jirman <[email protected]>Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
It looks like these fixes should be in separate patches. Is there any reason it's not the case?
Bullet points just describe the resulting effect/benefits of the change to fix the pipe control register update issue (see the referenced e-mail).
It's definitely ok to have multiple patches needed to address a single perceived issue.
Yes, but I can't simply split the patch. In order for each change to work on its own, they'd have to be done differently than the final result.
I wouldn't mind at all if it was just a simple splitting, but you're asking for too much work, this time, for no benefit that I can see.
Quoted 6 lines
A commit is not about what you're fixing but what you're changing. And the fact that you have tha bullet list in the first place proves that you have multiple logical changes in your patch.
And even then, your commit log mentions that you're fixing multiple issues (without explaining them).
Quoted 6 lines
I can reword the commit message if that helps, and skip the bullet list if it is confusing. There's a single core issue and that is that the driver doesn't update the pipe/channel configuration correctly leading to disabling of arbitrary layers (not even those being updated - update of UI layer may disable VI layer as a side effect for example) at wrong times. And only changes necessary to debug/fix this are included.
How about this:
A problem was found where identical configuration of planes leads to different register settings at the HW layer when using a X server with modesetting driver and one plane marked as a cursor.
On first run of the X server, only the black screen and the layer containing the cursor is visible. Switching to console and back corrects the situation.
I have dumped registers, and found out this:
(In both cases there are two enabled planes, plane 1 with zpos 0 and plane 3 with zpos 1).
1) First Xorg run:
0x01101000 : 00000201
0x01101080 : 00000030
BLD_FILL_COLOR_CTL: (aka SUN8I_MIXER_BLEND_PIPE_CTL)
P1_EN
BLD_CH_RTCTL: (aka SUN8I_MIXER_BLEND_ROUTE)
P0_RTCTL channel0
P1_RTCTL channel3
2) After switch to console and back to Xorg:
0x01101000 : 00000301
0x01101080 : 00000031
BLD_FILL_COLOR_CTL:
P1_EN and P0_EN
BLD_CH_RTCTL:
P0_RTCTL channel1
P1_RTCTL channel3
What happens is that sun8i_ui_layer_enable() function may disable blending pipes even if it is no longer assigned to its layer, because of incorrect state/zpos tracking in the driver.
In particular, layer 1 is configured to zpos 0 and thus uses pipe 0. When layer 3 is enabled by X server, sun8i_ui_layer_enable() will get called with old_zpos=0 zpos=1, which will lead to disabling of pipe 0.
In general this issue can happen to any layer during enable or zpos changes on multiple layers at once.
To correct this we now pass previous enabled/disabled state of the layer, and pass real previous zpos of the layer to sun8i_ui_layer_enable() and rework the sun8i_ui_layer_enable() function to react to the state changes correctly. In order to not complicate the atomic_disable callback with all of the above changes, we simply remove it and implement all the chanes as part of atomic_update, which also reduces the code duplication.
To make this all work, initial zpos positions of all layers need to be restored to initial values on reset.
Quoted 42 lines
I may try generating a nicer patch with a different diff options, if it makes it more readable for review.
Quoted 4 lines
Quoted 4 lines
I can maybe split off the first bullet point into a separate patch. But I can't guarantee it will not make the original issue worse, because it might have been hiding the other issue with register updates.
Quoted 8 lines
Quoted 5 lines
The rest is just a result of the single logical change. It doesn't work individually, it all has the goal of fixing the issue as a whole.
If I were to split it I would have to actually re-implement .atomic_disable callback only to remove it in the next patch. I don't see the benefit.
Your commit log says that you remove
atomic_disable. Why would you remove it, to add it back, to remove it again?Because if I remove it I need to re-implement the functionality in the update callback. The core will change what is called based on presence of callbacks. It's not a simple removal.
If I first implement the new sun8i_[uv]i_layer_enable and update callback, keeping a disable callback would not work, because the new update callback will only work if disable callback is not defined (because it it is, then the drm core will not call the update callback in all cases that I need).
regards,
o.Quoted 8 lines
Maxime
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Maxime Ripard
maintainerQuoted 52 lines · Ondřej Jirman
Quoted 44 lines · megous hlavni
Quoted 21 lines · Maxime Ripard
Quoted 20 lines · Ondřej Jirman
Hi,
Quoted 17 lines · Maxime Ripard
Hi,
Quoted 13 lines · On Sun, Sep 15, 2019 at 12:03:37AM +0200, [email protected] wrote:
From: Ondrej Jirman <[email protected]>
There are various issues that this re-work of sun8i_[uv]i_layer_enable function fixes:
- Make sure that we re-initialize zpos on reset
- Minimize register updates by doing them only when state changes
- Fix issue where DE pipe might get disabled even if it is no longer used by the layer that's currently callingsun8i_ui_layer_enable
- .atomic_disable callback is not really needed because .atomic_update can do the disable too, so drop the duplicate codeSigned-off-by Ondrej Jirman <[email protected]>Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
It looks like these fixes should be in separate patches. Is there any reason it's not the case?
Bullet points just describe the resulting effect/benefits of the change to fix the pipe control register update issue (see the referenced e-mail).
It's definitely ok to have multiple patches needed to address a single perceived issue.
Yes, but I can't simply split the patch. In order for each change to work on its own, they'd have to be done differently than the final result.
I wouldn't mind at all if it was just a simple splitting, but you're asking for too much work, this time, for no benefit that I can see.
Quoted 6 lines
A commit is not about what you're fixing but what you're changing. And the fact that you have tha bullet list in the first place proves that you have multiple logical changes in your patch.
And even then, your commit log mentions that you're fixing multiple issues (without explaining them).
Quoted 6 lines
I can reword the commit message if that helps, and skip the bullet list if it is confusing. There's a single core issue and that is that the driver doesn't update the pipe/channel configuration correctly leading to disabling of arbitrary layers (not even those being updated - update of UI layer may disable VI layer as a side effect for example) at wrong times. And only changes necessary to debug/fix this are included.
Quoted 5 lines
How about this:
A problem was found where identical configuration of planes leads to different register settings at the HW layer when using a X server with modesetting driver and one plane marked as a cursor.
We don't have a cursor plane.
Quoted 44 lines
On first run of the X server, only the black screen and the layer containing the cursor is visible. Switching to console and back corrects the situation.
I have dumped registers, and found out this:
(In both cases there are two enabled planes, plane 1 with zpos 0 and plane 3 with zpos 1).
1) First Xorg run:
0x01101000 : 00000201 0x01101080 : 00000030 BLD_FILL_COLOR_CTL: (aka SUN8I_MIXER_BLEND_PIPE_CTL) P1_EN BLD_CH_RTCTL: (aka SUN8I_MIXER_BLEND_ROUTE) P0_RTCTL channel0 P1_RTCTL channel32) After switch to console and back to Xorg:
0x01101000: 00000301
0x01101080: 00000031BLD_FILL_COLOR_CTL: P1_EN and P0_EN BLD_CH_RTCTL: P0_RTCTL channel1 P1_RTCTL channel3What happens is that
sun8i_ui_layer_enable()function may disable blending pipes even if it is no longer assigned to its layer, because of incorrect state/zpos tracking in the driver.In particular, layer 1 is configured to zpos 0 and thus uses pipe 0. When layer 3 is enabled by X server,
sun8i_ui_layer_enable()will get called with old_zpos=0 zpos=1, which will lead to disabling of pipe 0.In general this issue can happen to any layer during enable or zpos changes on multiple layers at once.
Quoted 7 lines
To correct this we now pass previous enabled/disabled state of the layer, and pass real previous zpos of the layer to
sun8i_ui_layer_enable()and rework thesun8i_ui_layer_enable()function to react to the state changes correctly. In order to not complicate theatomic_disablecallback with all of the above changes, we simply remove it and implement all the chanes as part ofatomic_update, which also reduces the code duplication.
I'm not even sure why we need that old state. Can't we just reset completely the whole thing and do the configuration all over again?
That description just looks to me like the reset is not done properly, and now we have to deal with the fallouts later on.
Quoted 2 lines
To make this all work, initial zpos positions of all layers need to be restored to initial values on reset.
And this also fixes a whole other bunch of issues, and can be made very trivially in a separate patch.
Maxime
Quoted 53 lines · Maxime Ripard
Quoted 52 lines · Ondřej Jirman
Quoted 50 lines · megous hlavni
Quoted 21 lines · Maxime Ripard
Quoted 20 lines · Ondřej Jirman
Hi,
Quoted 17 lines · Maxime Ripard
Hi,
Quoted 13 lines · On Sun, Sep 15, 2019 at 12:03:37AM +0200, [email protected] wrote:
From: Ondrej Jirman <[email protected]>
There are various issues that this re-work of sun8i_[uv]i_layer_enable function fixes:
- Make sure that we re-initialize zpos on reset
- Minimize register updates by doing them only when state changes
- Fix issue where DE pipe might get disabled even if it is no longer used by the layer that's currently callingsun8i_ui_layer_enable
- .atomic_disable callback is not really needed because .atomic_update can do the disable too, so drop the duplicate codeSigned-off-by Ondrej Jirman <[email protected]>Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
It looks like these fixes should be in separate patches. Is there any reason it's not the case?
Bullet points just describe the resulting effect/benefits of the change to fix the pipe control register update issue (see the referenced e-mail).
It's definitely ok to have multiple patches needed to address a single perceived issue.
Yes, but I can't simply split the patch. In order for each change to work on its own, they'd have to be done differently than the final result.
I wouldn't mind at all if it was just a simple splitting, but you're asking for too much work, this time, for no benefit that I can see.
Quoted 6 lines
A commit is not about what you're fixing but what you're changing. And the fact that you have tha bullet list in the first place proves that you have multiple logical changes in your patch.
And even then, your commit log mentions that you're fixing multiple issues (without explaining them).
I can reword the commit message if that helps, and skip the bullet list if it is confusing. There's a single core issue and that is that the driver doesn't update the pipe/channel configuration correctly leading to disabling of arbitrary layers (not even those being updated - update of UI layer may disable VI layer as a side effect for example) at wrong times. And only changes necessary to debug/fix this are included.
Quoted 7 lines
Quoted 5 lines
How about this:
A problem was found where identical configuration of planes leads to different register settings at the HW layer when using a X server with modesetting driver and one plane marked as a cursor.
We don't have a cursor plane.
Did I say we did? I only wrote that the problem was found this way. It's there regardless of how it was revealed.
Quoted 52 lines
Quoted 44 lines
On first run of the X server, only the black screen and the layer containing the cursor is visible. Switching to console and back corrects the situation.
I have dumped registers, and found out this:
(In both cases there are two enabled planes, plane 1 with zpos 0 and plane 3 with zpos 1).
1) First Xorg run:
0x01101000 : 00000201 0x01101080 : 00000030 BLD_FILL_COLOR_CTL: (aka SUN8I_MIXER_BLEND_PIPE_CTL) P1_EN BLD_CH_RTCTL: (aka SUN8I_MIXER_BLEND_ROUTE) P0_RTCTL channel0 P1_RTCTL channel32) After switch to console and back to Xorg:
0x01101000: 00000301
0x01101080: 00000031BLD_FILL_COLOR_CTL: P1_EN and P0_EN BLD_CH_RTCTL: P0_RTCTL channel1 P1_RTCTL channel3What happens is that
sun8i_ui_layer_enable()function may disable blending pipes even if it is no longer assigned to its layer, because of incorrect state/zpos tracking in the driver.In particular, layer 1 is configured to zpos 0 and thus uses pipe 0. When layer 3 is enabled by X server,
sun8i_ui_layer_enable()will get called with old_zpos=0 zpos=1, which will lead to disabling of pipe 0.In general this issue can happen to any layer during enable or zpos changes on multiple layers at once.
Quoted 7 lines
To correct this we now pass previous enabled/disabled state of the layer, and pass real previous zpos of the layer to
sun8i_ui_layer_enable()and rework thesun8i_ui_layer_enable()function to react to the state changes correctly. In order to not complicate theatomic_disablecallback with all of the above changes, we simply remove it and implement all the chanes as part ofatomic_update, which also reduces the code duplication.
Quoted 2 lines
I'm not even sure why we need that old state. Can't we just reset completely the whole thing and do the configuration all over again?
That would be nice from a dev standpoint if we can get a complete state for all planes at once from DRM core, but how? DRM helper gives callbacks for updating individual planes with prev and new state. These individual layer change notifications don't map nicely to how pipes are represented in the mixer registers.
Quoted 2 lines
That description just looks to me like the reset is not done properly, and now we have to deal with the fallouts later on.
What in particular?
Quoted 5 lines
Quoted 2 lines
To make this all work, initial zpos positions of all layers need to be restored to initial values on reset.
And this also fixes a whole other bunch of issues, and can be made very trivially in a separate patch.
Maybe reset should also reset registers?
regards,
o.
Quoted 6 lines
Maxime
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi,
Quoted 52 lines · megous hlavni
Quoted 52 lines
Quoted 51 lines
On first run of the X server, only the black screen and the layer containing the cursor is visible. Switching to console and back corrects the situation.
I have dumped registers, and found out this:
(In both cases there are two enabled planes, plane 1 with zpos 0 and plane 3 with zpos 1).
1) First Xorg run:
0x01101000 : 00000201 0x01101080 : 00000030 BLD_FILL_COLOR_CTL: (aka SUN8I_MIXER_BLEND_PIPE_CTL) P1_EN BLD_CH_RTCTL: (aka SUN8I_MIXER_BLEND_ROUTE) P0_RTCTL channel0 P1_RTCTL channel32) After switch to console and back to Xorg:
0x01101000: 00000301
0x01101080: 00000031BLD_FILL_COLOR_CTL: P1_EN and P0_EN BLD_CH_RTCTL: P0_RTCTL channel1 P1_RTCTL channel3What happens is that
sun8i_ui_layer_enable()function may disable blending pipes even if it is no longer assigned to its layer, because of incorrect state/zpos tracking in the driver.In particular, layer 1 is configured to zpos 0 and thus uses pipe 0. When layer 3 is enabled by X server,
sun8i_ui_layer_enable()will get called with old_zpos=0 zpos=1, which will lead to disabling of pipe 0.In general this issue can happen to any layer during enable or zpos changes on multiple layers at once.
To correct this we now pass previous enabled/disabled state of the layer, and pass real previous zpos of the layer to
sun8i_ui_layer_enable()and rework thesun8i_ui_layer_enable()function to react to the state changes correctly. In order to not complicate theatomic_disablecallback with all of the above changes, we simply remove it and implement all the chanes as part ofatomic_update, which also reduces the code duplication.
Quoted 8 lines
Quoted 2 lines
I'm not even sure why we need that old state. Can't we just reset completely the whole thing and do the configuration all over again?
That would be nice from a dev standpoint if we can get a complete state for all planes at once from DRM core, but how? DRM helper gives callbacks for updating individual planes with prev and new state. These individual layer change notifications don't map nicely to how pipes are represented in the mixer registers.
If anyone wants to pursue this further, feel free to. I'm not planning to pursue this fix further, at the moment.
regards,
o.
Maxime Ripard
maintainerQuoted 52 lines · Ondřej Jirman
Quoted 52 lines
Quoted 51 lines
On first run of the X server, only the black screen and the layer containing the cursor is visible. Switching to console and back corrects the situation.
I have dumped registers, and found out this:
(In both cases there are two enabled planes, plane 1 with zpos 0 and plane 3 with zpos 1).
1) First Xorg run:
0x01101000 : 00000201 0x01101080 : 00000030 BLD_FILL_COLOR_CTL: (aka SUN8I_MIXER_BLEND_PIPE_CTL) P1_EN BLD_CH_RTCTL: (aka SUN8I_MIXER_BLEND_ROUTE) P0_RTCTL channel0 P1_RTCTL channel32) After switch to console and back to Xorg:
0x01101000: 00000301
0x01101080: 00000031BLD_FILL_COLOR_CTL: P1_EN and P0_EN BLD_CH_RTCTL: P0_RTCTL channel1 P1_RTCTL channel3What happens is that
sun8i_ui_layer_enable()function may disable blending pipes even if it is no longer assigned to its layer, because of incorrect state/zpos tracking in the driver.In particular, layer 1 is configured to zpos 0 and thus uses pipe 0. When layer 3 is enabled by X server,
sun8i_ui_layer_enable()will get called with old_zpos=0 zpos=1, which will lead to disabling of pipe 0.In general this issue can happen to any layer during enable or zpos changes on multiple layers at once.
To correct this we now pass previous enabled/disabled state of the layer, and pass real previous zpos of the layer to
sun8i_ui_layer_enable()and rework thesun8i_ui_layer_enable()function to react to the state changes correctly. In order to not complicate theatomic_disablecallback with all of the above changes, we simply remove it and implement all the chanes as part ofatomic_update, which also reduces the code duplication.
Quoted 8 lines
Quoted 2 lines
I'm not even sure why we need that old state. Can't we just reset completely the whole thing and do the configuration all over again?
That would be nice from a dev standpoint if we can get a complete state for all planes at once from DRM core, but how? DRM helper gives callbacks for updating individual planes with prev and new state. These individual layer change notifications don't map nicely to how pipes are represented in the mixer registers.
You have a pointer to the full DRM state in the state field, so you have that option.
The other option is just to clear everything in atomic_begin, update each plane in atomic_update, and then trigger the readout of the new register values in atomic_commit.
Quoted 4 lines
Quoted 2 lines
That description just looks to me like the reset is not done properly, and now we have to deal with the fallouts later on.
What in particular?
Having to care about the old state? If the reset was done properly, we wouldn't have to care.
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
To make this all work, initial zpos positions of all layers need to be restored to initial values on reset.
And this also fixes a whole other bunch of issues, and can be made very trivially in a separate patch.
Maybe reset should also reset registers?
The reset callback actually does the opposite, it resets a DRM state. If anything, we want to initialize the state in reset by reading the registers, not the opposite.
Maxime