Add support for PM8950/PMI8950/PM8004 regulators
Subsystems (4)
cover Add support for PM8950/PMI8950/PM8004 regulators
From: "Angelo G. Del Regno" <[email protected]>
In this patch series, I'm adding support for the PM8950, PMI8950 and PM8004 regulators (smd/spmi).
The PM(I)8950 regulators are required for multiple SoCs, like MSM8956, MSM8976, MSM8953 (and maybe others), since they all use the same PM/PMI combo in their own variants.
The personal aim is to upstream MSM8956 as much as possible.
This code has been tested on two Sony phones featuring the Qualcomm MSM8956 SoC, with PM/PMI8950 and PM8004.
Angelo G. Del Regno (5):
qcom: spmi-regulator: Add support for ULT LV_P50 and ULT P300
regulator: qcom_spmi: Add PM8950 SPMI regulator
regulator: qcom_smd: Add PM8950 regulators
mfd: qcom-spmi-pmic: Add support for PM/PMI8950
regulator: qcom_spmi: Add support for PM8004 regulators
.../bindings/mfd/qcom,spmi-pmic.txt | 2 + .../regulator/qcom,smd-rpm-regulator.txt | 21 +++++ .../regulator/qcom,spmi-regulator.txt | 25 +++++ drivers/mfd/qcom-spmi-pmic.c | 4 + drivers/regulator/qcom_smd-regulator.c | 92 +++++++++++++++++++ drivers/regulator/qcom_spmi-regulator.c | 43 +++++++++ 6 files changed, 187 insertions(+)
Signature · 1 line
2.21.0
PATCH 1/5 qcom: spmi-regulator: Add support for ULT LV_P50 and ULT P300
From: "Angelo G. Del Regno" <[email protected]>
The ULT LV_P50 shares the same configuration as the other ULT LV_Pxxx and the ULT P300 shares the same as the other ULT Pxxx.
These two regulator types are found on PM8950 and its variants.
--- drivers/regulator/qcom_spmi-regulator.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/regulator/qcom_spmi-regulator.c +2 -0
@@ -1466,10 +1466,12 @@ static const struct spmi_regulator_mapping supported_regulators[] = {SPMI_VREG (ULT_LDO ,N600_ST ,0 ,INF ,ULT_LDO , ult_ldo, ult_nldo,10000 ),SPMI_VREG (ULT_LDO ,N900_ST ,0 ,INF ,ULT_LDO , ult_ldo, ult_nldo,10000 ),SPMI_VREG (ULT_LDO ,N1200_ST ,0 ,INF ,ULT_LDO , ult_ldo, ult_nldo,10000 ), +SPMI_VREG (ULT_LDO ,LV_P50 ,0 ,INF ,ULT_LDO , ult_ldo, ult_pldo,10000 ),SPMI_VREG (ULT_LDO ,LV_P150 ,0 ,INF ,ULT_LDO , ult_ldo, ult_pldo,10000 ),SPMI_VREG (ULT_LDO ,LV_P300 ,0 ,INF ,ULT_LDO , ult_ldo, ult_pldo,10000 ),SPMI_VREG (ULT_LDO ,LV_P450 ,0 ,INF ,ULT_LDO , ult_ldo, ult_pldo,10000 ),SPMI_VREG (ULT_LDO ,P600 ,0 ,INF ,ULT_LDO , ult_ldo, ult_pldo,10000 ), +SPMI_VREG (ULT_LDO ,P300 ,0 ,INF ,ULT_LDO , ult_ldo, ult_pldo,10000 ),SPMI_VREG (ULT_LDO ,P150 ,0 ,INF ,ULT_LDO , ult_ldo, ult_pldo,10000 ), SPMI_VREG(ULT_LDO, P50, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 5000), };
Signature · 1 line
2.21.0
PATCH 2/5 regulator: qcom_spmi: Add PM8950 SPMI regulator
In reply to [email protected]From: "Angelo G. Del Regno" <[email protected]>
The PM8950 has 5 HFSMPS, 1 FTSMPS2.5 (s5, controlling APC voltage) and 23 LDO regulators.
Add the configuration for this chip.
--- .../regulator/qcom,spmi-regulator.txt | 21 ++++++++++++ drivers/regulator/qcom_spmi-regulator.c | 34 +++++++++++++++++++ 2 files changed, 55 insertions(+)
Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +21 -0
@@ -8,6 +8,7 @@ Qualcomm SPMI Regulators "qcom,pm8841-regulators" "qcom,pm8916-regulators" "qcom,pm8941-regulators" + "qcom,pm8950-regulators" "qcom,pm8994-regulators" "qcom,pmi8994-regulators" "qcom,pms405-regulators"
@@ -72,6 +73,26 @@ Qualcomm SPMI Regulators Definition: Reference to regulator supplying the input pin, as described in the data sheet. +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_l1_l19-supply: +- vdd_l2_l23-supply: +- vdd_l3-supply: +- vdd_l4_l5_l6_l7_l16-supply: +- vdd_l8_l11_l12_l17_l22-supply: +- vdd_l9_l10_l13_l14_l15_l18-supply: +- vdd_l20-supply: +- vdd_l21-supply: + Usage: optional (pm8950 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + - vdd_s1-supply: - vdd_s2-supply: - vdd_s3-supply:
drivers/regulator/qcom_spmi-regulator.c +34 -0
@@ -1871,6 +1871,39 @@ static const struct spmi_regulator_data pm8916_regulators[] = { { } }; +static const struct spmi_regulator_data pm8950_regulators[] = { + {"s1" ,0x1400 ,"vdd_s1" , }, + {"s2" ,0x1700 ,"vdd_s2" , }, + {"s3" ,0x1a00 ,"vdd_s3" , }, + {"s4" ,0x1d00 ,"vdd_s4" , }, + {"s5" ,0x2000 ,"vdd_s5" , }, + {"s6" ,0x2300 ,"vdd_s6" , }, + {"l1" ,0x4000 ,"vdd_l1_l19" , }, + {"l2" ,0x4100 ,"vdd_l2_l23" , }, + {"l3" ,0x4200 ,"vdd_l3" , }, + {"l4" ,0x4300 ,"vdd_l4_l5_l6_l7_l16" , }, + {"l5" ,0x4400 ,"vdd_l4_l5_l6_l7_l16" , }, + {"l6" ,0x4500 ,"vdd_l4_l5_l6_l7_l16" , }, + {"l7" ,0x4600 ,"vdd_l4_l5_l6_l7_l16" , }, + {"l8" ,0x4700 ,"vdd_l8_l11_l12_l17_l22" , }, + {"l9" ,0x4800 ,"vdd_l9_l10_l13_l14_l15_l18" , }, + {"l10" ,0x4900 ,"vdd_l9_l10_l13_l14_l15_l18" , }, + {"l11" ,0x4a00 ,"vdd_l8_l11_l12_l17_l22" , }, + {"l12" ,0x4b00 ,"vdd_l8_l11_l12_l17_l22" , }, + {"l13" ,0x4c00 ,"vdd_l9_l10_l13_l14_l15_l18" , }, + {"l14" ,0x4d00 ,"vdd_l9_l10_l13_l14_l15_l18" , }, + {"l15" ,0x4e00 ,"vdd_l9_l10_l13_l14_l15_l18" , }, + {"l16" ,0x4f00 ,"vdd_l4_l5_l6_l7_l16" , }, + {"l17" ,0x5000 ,"vdd_l8_l11_l12_l17_l22" , }, + {"l18" ,0x5100 ,"vdd_l9_l10_l13_l14_l15_l18" , }, + {"l19" ,0x5200 ,"vdd_l1_l19" , }, + {"l20" ,0x5300 ,"vdd_l20" , }, + {"l21" ,0x5400 ,"vdd_l21" , }, + {"l22" ,0x5500 ,"vdd_l8_l11_l12_l17_l22" , }, + {"l23" ,0x5600 ,"vdd_l2_l23" , }, + { } +}; +static const struct spmi_regulator_data pm8994_regulators[] = { {"s1" ,0x1400 ,"vdd_s1" , }, {"s2" ,0x1700 ,"vdd_s2" , },
@@ -1947,6 +1980,7 @@ static const struct of_device_id qcom_spmi_regulator_match[] = { { .compatible = "qcom,pm8841-regulators", .data = &pm8841_regulators }, { .compatible = "qcom,pm8916-regulators", .data = &pm8916_regulators }, { .compatible = "qcom,pm8941-regulators", .data = &pm8941_regulators }, + { .compatible = "qcom,pm8950-regulators", .data = &pm8950_regulators }, { .compatible = "qcom,pm8994-regulators", .data = &pm8994_regulators }, { .compatible = "qcom,pmi8994-regulators", .data = &pmi8994_regulators }, { .compatible = "qcom,pms405-regulators", .data = &pms405_regulators },
Signature · 1 line
2.21.0
PATCH 3/5 regulator: qcom_smd: Add PM8950 regulators
In reply to [email protected]From: "Angelo G. Del Regno" <[email protected]>
The PM8950 provides 6 SMPS regulators, of which 5 HFSMPS and one FTSMPS2.5 (s5), and 23 LDOs.
Add these to the RPM regulator driver.
--- .../regulator/qcom,smd-rpm-regulator.txt | 21 +++++ drivers/regulator/qcom_smd-regulator.c | 92 +++++++++++++++++++ 2 files changed, 113 insertions(+)
Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt +21 -0
@@ -22,6 +22,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8841-regulators" "qcom,rpm-pm8916-regulators" "qcom,rpm-pm8941-regulators" + "qcom,rpm-pm8950-regulators" "qcom,rpm-pm8994-regulators" "qcom,rpm-pm8998-regulators" "qcom,rpm-pma8084-regulators"
@@ -54,6 +55,26 @@ Regulator nodes are identified by their compatible: Definition: reference to regulator supplying the input pin, as described in the data sheet +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_l1_l19-supply: +- vdd_l2_l23-supply: +- vdd_l3-supply: +- vdd_l4_l5_l6_l7_l16-supply: +- vdd_l8_l11_l12_l17_l22-supply: +- vdd_l9_l10_l13_l14_l15_l18-supply: +- vdd_l20-supply: +- vdd_l21-supply: + Usage: optional (pm8950 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + - vdd_s1-supply: - vdd_s2-supply: - vdd_s3-supply:
drivers/regulator/qcom_smd-regulator.c +92 -0
110 lines not on this page · raw message
Signature · 1 line
2.21.0
PATCH 4/5 mfd: qcom-spmi-pmic: Add support for PM/PMI8950
In reply to [email protected]From: "Angelo G. Del Regno" <[email protected]>
Add the subtype and compatible strings for PM8950 and PMI8950, found in various SoCs, including MSM8953, MSM8956, MSM8976 and APQ variants.
--- Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt | 2 ++ drivers/mfd/qcom-spmi-pmic.c | 4 ++++ 2 files changed, 6 insertions(+)
Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt +2 -0
@@ -29,6 +29,8 @@ Required properties: "qcom,pm8916", "qcom,pm8004", "qcom,pm8909", + "qcom,pm8950", + "qcom,pmi8950", "qcom,pm8998", "qcom,pmi8998", "qcom,pm8005",
drivers/mfd/qcom-spmi-pmic.c +4 -0
@@ -31,6 +31,8 @@#define PM8916_SUBTYPE 0x0b#define PM8004_SUBTYPE 0x0c#define PM8909_SUBTYPE 0x0d +#define PM8950_SUBTYPE 0x10 +#define PMI8950_SUBTYPE 0x11#define PM8998_SUBTYPE 0x14#define PMI8998_SUBTYPE 0x15#define PM8005_SUBTYPE 0x18
@@ -50,6 +52,8 @@ static const struct of_device_id pmic_spmi_id_table[] = { { .compatible = "qcom,pm8916", .data = (void *)PM8916_SUBTYPE }, { .compatible = "qcom,pm8004", .data = (void *)PM8004_SUBTYPE }, { .compatible = "qcom,pm8909", .data = (void *)PM8909_SUBTYPE }, + { .compatible = "qcom,pm8950", .data = (void *)PM8950_SUBTYPE }, + { .compatible = "qcom,pmi8950", .data = (void *)PMI8950_SUBTYPE }, { .compatible = "qcom,pm8998", .data = (void *)PM8998_SUBTYPE }, { .compatible = "qcom,pmi8998", .data = (void *)PMI8998_SUBTYPE }, { .compatible = "qcom,pm8005", .data = (void *)PM8005_SUBTYPE },
Signature · 1 line
2.21.0
Lee Jones
AppliedRe: [PATCH 4/5] mfd: qcom-spmi-pmic: Add support for PM/PMI8950
Quoted 11 lines · On Sat, 21 Sep 2019, [email protected] wrote:
From: "Angelo G. Del Regno" <[email protected]>
Add the subtype and compatible strings for PM8950 and PMI8950, found in various SoCs, including MSM8953, MSM8956, MSM8976 and APQ variants.
Signed-off-by Angelo G. Del Regno <[email protected]>--- Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt | 2 ++ drivers/mfd/qcom-spmi-pmic.c | 4 ++++ 2 files changed, 6 insertions(+)
Applied, thanks.
Signature · 4 lines
Lee Jones [李琼斯] Linaro Services Technical Lead Linaro.org │ Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog
PATCH 5/5 regulator: qcom_spmi: Add support for PM8004 regulators
In reply to [email protected]From: "Angelo G. Del Regno" <[email protected]>
This Power IC is used in combination with various PMIC combos, generally found on boards with MSM8992, MSM8994, MSM8996, MSM8956, MSM8976 and others, usually at address 0x5 on the SPMI bus, and its usual usage is to provide power to the GPU and/or to the CPU clusters (APC0/APC1).
--- .../devicetree/bindings/regulator/qcom,spmi-regulator.txt | 4 ++++ drivers/regulator/qcom_spmi-regulator.c | 7 +++++++ 2 files changed, 11 insertions(+)
Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +4 -0
@@ -4,6 +4,7 @@ Qualcomm SPMI Regulators Usage: required Value type: <string> Definition: must be one of: + "qcom,pm8004-regulators" "qcom,pm8005-regulators" "qcom,pm8841-regulators" "qcom,pm8916-regulators"
@@ -160,6 +161,9 @@ The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the PMICs below. +pm8005: + s2, s5 + pm8005: s1, s2, s3, s4
drivers/regulator/qcom_spmi-regulator.c +7 -0
@@ -1962,6 +1962,12 @@ static const struct spmi_regulator_data pmi8994_regulators[] = { { } }; +static const struct spmi_regulator_data pm8004_regulators[] = { + {"s2" ,0x1700 ,"vdd_s2" , }, + {"s5" ,0x2000 ,"vdd_s5" , }, + { } +}; +static const struct spmi_regulator_data pm8005_regulators[] = { {"s1" ,0x1400 ,"vdd_s1" , }, {"s2" ,0x1700 ,"vdd_s2" , },
@@ -1976,6 +1982,7 @@ static const struct spmi_regulator_data pms405_regulators[] = { };static const struct of_device_id qcom_spmi_regulator_match[] = { + { .compatible ="qcom,pm8004-regulators" , .data = &pm8004_regulators }, { .compatible ="qcom,pm8005-regulators" , .data = &pm8005_regulators }, { .compatible ="qcom,pm8841-regulators" , .data = &pm8841_regulators }, { .compatible ="qcom,pm8916-regulators" , .data = &pm8916_regulators },
Signature · 1 line
2.21.0