drm/i915/dp: Fix dsc bpp calculations, v5.
PATCH 1/2 drm/i915/dp: Fix dsc bpp calculations, v5.
There was a integer wraparound when mode_clock became too high, and we didn't correct for the FEC overhead factor when dividing, with the calculations breaking at HBR3.
As a result our calculated bpp was way too high, and the link width limitation never came into effect.
Print out the resulting bpp calcululations as a sanity check, just in case we ever have to debug it later on again.
We also used the wrong factor for FEC. While bspec mentions 2.4%, all the calculations use 1/0.972261, and the same ratio should be applied to data M/N as well, so use it there when FEC is enabled.
This fixes the FIFO underrun we are seeing with FEC enabled.
Changes since v2:
- Handle fec_enable in intel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogus fec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.
--- drivers/gpu/drm/i915/display/intel_display.c | 12 +- drivers/gpu/drm/i915/display/intel_display.h | 2 +- drivers/gpu/drm/i915/display/intel_dp.c | 184 ++++++++++--------- drivers/gpu/drm/i915/display/intel_dp.h | 6 +- drivers/gpu/drm/i915/display/intel_dp_mst.c | 2 +- 5 files changed, 107 insertions(+), 99 deletions(-)
drivers/gpu/drm/i915/display/intel_display.c +8 -4
@@ -7291,7 +7291,7 @@ static int ironlake_fdi_compute_config(struct intel_crtc *intel_crtc, pipe_config->fdi_lanes = lane;intel_link_compute_m_n (pipe_config->pipe_bpp, lane, fdi_dotclock, - link_bw, &pipe_config->fdi_m_n, false); + link_bw, &pipe_config->fdi_m_n, false, false); ret =ironlake_check_fdi_lanes (dev, intel_crtc->pipe, pipe_config);if (ret == -EDEADLK )
@@ -7538,11 +7538,15 @@ void intel_link_compute_m_n(u16 bits_per_pixel, int nlanes, int pixel_clock, int link_clock, struct intel_link_m_n *m_n, - bool constant_n) + bool constant_n, bool fec_enable) { - m_n->tu = 64; + u32 data_clock = bits_per_pixel * pixel_clock; + +if (fec_enable) + data_clock =intel_dp_mode_to_fec_clock (data_clock); -compute_m_n (bits_per_pixel * pixel_clock, + m_n->tu =64 ; +compute_m_n (data_clock, link_clock * nlanes *8 , &m_n->gmch_m, &m_n->gmch_n, constant_n);
drivers/gpu/drm/i915/display/intel_display.h +1 -1
@@ -443,7 +443,7 @@ enum phy_fia {void intel_link_compute_m_n (u16 bpp,int nlanes,int pixel_clock,int link_clock,struct intel_link_m_n *m_n, -bool constant_n); +bool constant_n,bool fec_enable);bool is_ccs_modifier (u64 modifier);void lpt_disable_clkout_dp (struct drm_i915_private *dev_priv); u32 intel_plane_fb_max_stride(struct drm_i915_private *dev_priv,
drivers/gpu/drm/i915/display/intel_dp.c +95 -89
214 lines not on this page · raw message
drivers/gpu/drm/i915/display/intel_dp.h +2 -4
@@ -103,10 +103,6 @@ bool intel_dp_source_supports_hbr2(struct intel_dp *intel_dp);bool intel_dp_source_supports_hbr3 (struct intel_dp *intel_dp);bool intel_dp_get_link_status (struct intel_dp *intel_dp,u8 *link_status); -u16 intel_dp_dsc_get_output_bpp (int link_clock,u8 lane_count, -int mode_clock,int mode_hdisplay); -u8 intel_dp_dsc_get_slice_count (struct intel_dp *intel_dp,int mode_clock, -int mode_hdisplay);bool intel_dp_read_dpcd (struct intel_dp *intel_dp);bool intel_dp_get_colorimetry_status (struct intel_dp *intel_dp);
@@ -119,4 +115,6 @@ static inline unsigned int intel_dp_unused_lane_mask(int lane_count) return ~((1 << lane_count) - 1) & 0xf; } +u32 intel_dp_mode_to_fec_clock (u32 mode_clock); +#endif /* __INTEL_DP_H__ */
drivers/gpu/drm/i915/display/intel_dp_mst.c +1 -1
@@ -81,7 +81,7 @@ static int intel_dp_mst_compute_link_config(struct intel_encoder *encoder, adjusted_mode->crtc_clock, crtc_state->port_clock, &crtc_state->dp_m_n, - constant_n); + constant_n, crtc_state->fec_enable); crtc_state->dp_m_n.tu = slots;return 0 ;
Signature · 1 line
2.20.1
PATCH 2/2 drm/i915: Add hardware readout for FEC
Readout the FEC state in encoder->get_config(), this will allow us to ensure that we can correctly inherit the state from boot, and that we set FEC during modeset.
--- drivers/gpu/drm/i915/display/intel_ddi.c | 17 +++++++++++++++++ drivers/gpu/drm/i915/display/intel_display.c | 1 + 2 files changed, 18 insertions(+)
drivers/gpu/drm/i915/display/intel_ddi.c +17 -0
@@ -4021,6 +4021,23 @@ void intel_ddi_get_config(struct intel_encoder *encoder, pipe_config->lane_count = ((temp &DDI_PORT_WIDTH_MASK ) >>DDI_PORT_WIDTH_SHIFT ) +1 ;intel_dp_get_m_n (intel_crtc, pipe_config); + +if (INTEL_GEN (dev_priv) >=11 ) { +i915_reg_t dp_tp_ctl; + +if (IS_GEN (dev_priv,11 )) + dp_tp_ctl =DP_TP_CTL (encoder->port); +else + dp_tp_ctl =TGL_DP_TP_CTL (pipe_config->cpu_transcoder); + + pipe_config->fec_enable = +I915_READ (dp_tp_ctl) &DP_TP_CTL_FEC_ENABLE ; + +DRM_DEBUG_KMS ("[ENCODER:%d:%s] Fec status: %u\n" , + encoder->base.base.id, encoder->base.name, + pipe_config->fec_enable); + } +break ;case TRANS_DDI_MODE_SELECT_DP_MST : pipe_config->output_types |=BIT (INTEL_OUTPUT_DP_MST );
drivers/gpu/drm/i915/display/intel_display.c +1 -0
@@ -12836,6 +12836,7 @@ intel_pipe_config_compare(const struct intel_crtc_state *current_config,PIPE_CONF_CHECK_BOOL (hdmi_scrambling);PIPE_CONF_CHECK_BOOL (hdmi_high_tmds_clock_ratio);PIPE_CONF_CHECK_BOOL (has_infoframe); +PIPE_CONF_CHECK_BOOL (fec_enable);PIPE_CONF_CHECK_BOOL_INCOMPLETE (has_audio);
Signature · 6 lines
2.20.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.CHECKPATCH: warning for series starting with [1/2] drm/i915/dp: Fix dsc bpp calculations, v5.
In reply to Maarten Lankhorst== Series Details ==
== Series Details ==
Series: series starting with [1/2] drm/i915/dp: Fix dsc bpp calculations, v5.
URL : https://patchwork.freedesktop.org/series/67203/
State : warning
== Summary ==
$ dim checkpatch origin/drm-tip ae2d2fb87831 drm/i915/dp: Fix dsc bpp calculations, v5. -:23: WARNING:COMMIT_LOG_LONG_LINE: Possible unwrapped commit description (prefer a maximum 75 chars per line) #23: - Handle fec_enable in intel_link_compute_m_n, so only data M/N is adjusted. (Ville)
total: 0 errors, 1 warnings, 0 checks, 272 lines checked 43fc9a688962 drm/i915: Add hardware readout for FEC
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for series starting with [1/2] drm/i915/dp: Fix dsc bpp calculations, v5.
In reply to Maarten Lankhorst== Series Details ==
== Series Details ==
Series: series starting with [1/2] drm/i915/dp: Fix dsc bpp calculations, v5.
URL : https://patchwork.freedesktop.org/series/67203/
State : success
== Summary ==
CI Bug Log - changes from CI_DRM_6954 -> Patchwork_14526
====================================================
Summary
-------
**SUCCESS**
No regressions found.
External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/
Possible new issues
-------------------
Here are the unknown changes that may have been introduced in Patchwork_14526:
### IGT changes ###
#### Suppressed ####
The following results come from untrusted machines, tests, or statuses. They do not affect the overall result.
* igt@gem_exec_suspend@basic-s4-devices:
- {fi-tgl-u2}: [PASS][1] -> [INCOMPLETE][2]
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/fi-tgl-u2/igt@[email protected]
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/fi-tgl-u2/igt@[email protected]
Known issues
------------
Here are the changes found in Patchwork_14526 that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@gem_exec_suspend@basic-s3:
- fi-blb-e6850: [PASS][3] -> [INCOMPLETE][4] ([fdo#107718])
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/fi-blb-e6850/igt@[email protected]
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/fi-blb-e6850/igt@[email protected]
#### Possible fixes ####
* igt@kms_frontbuffer_tracking@basic:
- fi-hsw-peppy: [DMESG-WARN][5] ([fdo#102614]) -> [PASS][6]
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/fi-hsw-peppy/igt@[email protected]
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/fi-hsw-peppy/igt@[email protected]
{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).
[fdo#102614]: https://bugs.freedesktop.org/show_bug.cgi?id=102614
[fdo#107718]: https://bugs.freedesktop.org/show_bug.cgi?id=107718
Participating hosts (51 -> 44)
------------------------------
Missing (7): fi-ilk-m540 fi-hsw-4200u fi-byt-squawks fi-bsw-cyan fi-icl-y fi-byt-clapper fi-bdw-samus
Build changes
-------------
* CI: CI-20190529 -> None
* Linux: CI_DRM_6954 -> Patchwork_14526
CI-20190529: 20190529
CI_DRM_6954: 80fa0e042cdb3da59d2c738db61b8da78cf29e0d @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_5202: 3499c5eb17054e2abd88023fe962768140d24302 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_14526: 43fc9a688962d5678e6dfd105530a519b5b7e935 @ git://anongit.freedesktop.org/gfx-ci/linux
== Linux commits ==
43fc9a688962 drm/i915: Add hardware readout for FEC ae2d2fb87831 drm/i915/dp: Fix dsc bpp calculations, v5.
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/index.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 111 lines · Maarten Lankhorst
There was a integer wraparound when
mode_clockbecame too high, and we didn't correct for the FEC overhead factor when dividing, with the calculations breaking at HBR3.As a result our calculated bpp was way too high, and the link width limitation never came into effect.
Print out the resulting bpp calcululations as a sanity check, just in case we ever have to debug it later on again.
We also used the wrong factor for FEC. While bspec mentions 2.4%, all the calculations use 1/0.972261, and the same ratio should be applied to data M/N as well, so use it there when FEC is enabled.
This fixes the FIFO underrun we are seeing with FEC enabled.
Changes since v2:
- Handlefec_enableinintel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogusfec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.Signed-off-by Maarten Lankhorst <[email protected]>Fixes d9218c8f6cf4 ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")Cc <[email protected]> # v5.0+Cc Manasi Navare <[email protected]>--- drivers/gpu/drm/i915/display/intel_display.c | 12 +- drivers/gpu/drm/i915/display/intel_display.h | 2 +- drivers/gpu/drm/i915/display/intel_dp.c | 184 ++++++++++--------- drivers/gpu/drm/i915/display/intel_dp.h | 6 +- drivers/gpu/drm/i915/display/intel_dp_mst.c | 2 +- 5 files changed, 107 insertions(+), 99 deletions(-)drivers/gpu/drm/i915/display/intel_display.c +8
-4@@ -7291,7 +7291,7 @@ static int ironlake_fdi_compute_config(struct intel_crtc *intel_crtc, pipe_config->fdi_lanes = lane;intel_link_compute_m_n (pipe_config->pipe_bpp, lane, fdi_dotclock, - link_bw, &pipe_config->fdi_m_n, false); + link_bw, &pipe_config->fdi_m_n, false, false); ret =ironlake_check_fdi_lanes (dev, intel_crtc->pipe, pipe_config);if (ret == -EDEADLK )@@ -7538,11 +7538,15 @@ void intel_link_compute_m_n(u16 bits_per_pixel, int nlanes, int pixel_clock, int link_clock, struct intel_link_m_n *m_n, - bool constant_n) + bool constant_n, bool fec_enable) { - m_n->tu = 64; + u32 data_clock = bits_per_pixel * pixel_clock; + +if (fec_enable) + data_clock =intel_dp_mode_to_fec_clock (data_clock); -compute_m_n (bits_per_pixel * pixel_clock, + m_n->tu =64 ; +compute_m_n (data_clock, link_clock * nlanes *8 , &m_n->gmch_m, &m_n->gmch_n, constant_n);drivers/gpu/drm/i915/display/intel_display.h +1
-1@@ -443,7 +443,7 @@ enum phy_fia {void intel_link_compute_m_n (u16 bpp,int nlanes,int pixel_clock,int link_clock,struct intel_link_m_n *m_n, -bool constant_n); +bool constant_n,bool fec_enable);bool is_ccs_modifier (u64 modifier);void lpt_disable_clkout_dp (struct drm_i915_private *dev_priv); u32 intel_plane_fb_max_stride(struct drm_i915_private *dev_priv,drivers/gpu/drm/i915/display/intel_dp.c +12
-2@@ -76,8 +76,8 @@#define DP_DSC_MAX_ENC_THROUGHPUT_0 340000#define DP_DSC_MAX_ENC_THROUGHPUT_1 400000 -/* DP DSC FEC Overhead factor = (100 - 2.4)/100 */ -#define DP_DSC_FEC_OVERHEAD_FACTOR 976 +/* DP DSC FEC Overhead factor = 1/(0.972261) */ +#define DP_DSC_FEC_OVERHEAD_FACTOR 972261/* Compliance test status bits */ #define INTEL_DP_RESOLUTION_SHIFT_MASK 0@@ -492,6 +492,97 @@ int intel_dp_get_link_train_fallback_values(struct intel_dp *intel_dp,return 0 ; } +u32 intel_dp_mode_to_fec_clock (u32 mode_clock) +{ +return div_u64 (mul_u32_u32 (mode_clock,1000000U ), +DP_DSC_FEC_OVERHEAD_FACTOR ); +} + +static u16 intel_dp_dsc_get_output_bpp (u32 link_clock,u32 lane_count, +u32 mode_clock,u32 mode_hdisplay) +{ +u32 bits_per_pixel, max_bpp_small_joiner_ram;
drivers/gpu/drm/i915/display/intel_dp.c int intel_dp_get_link_train_fallback_values(struct intel_dp *intel_dp, · line 514
Quoted 10 lines
drivers/gpu/drm/i915/display/intel_dp.c +10
-0+int i; + +/* +* Available Link Bandwidth(Kbits/sec) = (NumberOfLanes)* +* (LinkSymbolClock)* 8 * (TimeSlotsPerMTP) +* for SST -> TimeSlotsPerMTP is 1, +* for MST -> TimeSlotsPerMTP has to be calculated +*/ + bits_per_pixel = (link_clock * lane_count *8 ) / +intel_dp_mode_to_fec_clock (mode_clock);
Hmm. Aren't we adding the FEC overhead twice now when DSC is also enabled?
Quoted 226 lines
drivers/gpu/drm/i915/display/intel_dp.c +73
-87+DRM_DEBUG_KMS ("Max link bpp: %u\n" , bits_per_pixel); + +/* Small Joiner Check: output bpp <= joiner RAM (bits) / Horiz. width */ + max_bpp_small_joiner_ram =DP_DSC_MAX_SMALL_JOINER_RAM_BUFFER / mode_hdisplay; +DRM_DEBUG_KMS ("Max small joiner bpp: %u\n" , max_bpp_small_joiner_ram); + +/* +* Greatest allowed DSC BPP = MIN (output BPP from available Link BW +* check, output bpp from small joiner RAM check) +*/ + bits_per_pixel =min (bits_per_pixel, max_bpp_small_joiner_ram); + +/* Error out if the max bpp is less than smallest allowed valid bpp */ +if (bits_per_pixel < valid_dsc_bpp[0 ]) { +DRM_DEBUG_KMS ("Unsupported BPP %u, min %u\n" , + bits_per_pixel, valid_dsc_bpp[0 ]); +return 0 ; + } + +/* Find the nearest match in the array of known BPPs from VESA */ +for (i =0 ; i <ARRAY_SIZE (valid_dsc_bpp) -1 ; i++) { +if (bits_per_pixel < valid_dsc_bpp[i +1 ]) +break ; + } + bits_per_pixel = valid_dsc_bpp[i]; + +/* +* Compressed BPP in U6.4 format so multiply by 16, for Gen 11, +* fractional part is 0 +*/ +return bits_per_pixel <<4 ; +} + +static u8 intel_dp_dsc_get_slice_count (struct intel_dp *intel_dp, +int mode_clock,int mode_hdisplay) +{ +u8 min_slice_count, i; +int max_slice_width; + +if (mode_clock <=DP_DSC_PEAK_PIXEL_RATE ) + min_slice_count =DIV_ROUND_UP (mode_clock, +DP_DSC_MAX_ENC_THROUGHPUT_0 ); +else + min_slice_count =DIV_ROUND_UP (mode_clock, +DP_DSC_MAX_ENC_THROUGHPUT_1 ); + + max_slice_width =drm_dp_dsc_sink_max_slice_width (intel_dp->dsc_dpcd); +if (max_slice_width <DP_DSC_MIN_SLICE_WIDTH_VALUE ) { +DRM_DEBUG_KMS ("Unsupported slice width %d by DP DSC Sink device\n" , + max_slice_width); +return 0 ; + } +/* Also take into account max slice width */ + min_slice_count =min_t (u8, min_slice_count, +DIV_ROUND_UP (mode_hdisplay, + max_slice_width)); + +/* Find the closest match to the valid slice count values */ +for (i =0 ; i <ARRAY_SIZE (valid_dsc_slicecount); i++) { +if (valid_dsc_slicecount[i] > +drm_dp_dsc_sink_max_slice_count (intel_dp->dsc_dpcd, + false)) +break ; +if (min_slice_count <= valid_dsc_slicecount[i]) +return valid_dsc_slicecount[i]; + } + +DRM_DEBUG_KMS ("Unsupported Slice Count %d\n" , min_slice_count); +return 0 ; +} +static enum drm_mode_status intel_dp_mode_valid (struct drm_connector *connector,struct drm_display_mode *mode)@@ -2259,7 +2350,7 @@ intel_dp_compute_config(struct intel_encoder *encoder, adjusted_mode->crtc_clock, pipe_config->port_clock, &pipe_config->dp_m_n, - constant_n); + constant_n, pipe_config->fec_enable);if (intel_connector->panel.downclock_mode !=NULL && dev_priv->drrs.type ==SEAMLESS_DRRS_SUPPORT ) {@@ -2269,7 +2360,7 @@ intel_dp_compute_config(struct intel_encoder *encoder, intel_connector->panel.downclock_mode->clock, pipe_config->port_clock, &pipe_config->dp_m2_n2, - constant_n); + constant_n, pipe_config->fec_enable); }if (!HAS_DDI (dev_priv))@@ -4373,91 +4464,6 @@ intel_dp_get_sink_irq_esi(struct intel_dp *intel_dp, u8 *sink_irq_vector)DP_DPRX_ESI_LEN ; } -u16 intel_dp_dsc_get_output_bpp (int link_clock,u8 lane_count, -int mode_clock,int mode_hdisplay) -{ -u16 bits_per_pixel, max_bpp_small_joiner_ram; -int i; - -/* -* Available Link Bandwidth(Kbits/sec) = (NumberOfLanes)* -* (LinkSymbolClock)* 8 * ((100-FECOverhead)/100)*(TimeSlotsPerMTP) -* FECOverhead = 2.4%, for SST -> TimeSlotsPerMTP is 1, -* for MST -> TimeSlotsPerMTP has to be calculated -*/ - bits_per_pixel = (link_clock * lane_count *8 * -DP_DSC_FEC_OVERHEAD_FACTOR ) / - mode_clock; - -/* Small Joiner Check: output bpp <= joiner RAM (bits) / Horiz. width */ - max_bpp_small_joiner_ram =DP_DSC_MAX_SMALL_JOINER_RAM_BUFFER / - mode_hdisplay; - -/* -* Greatest allowed DSC BPP = MIN (output BPP from avaialble Link BW -* check, output bpp from small joiner RAM check) -*/ - bits_per_pixel =min (bits_per_pixel, max_bpp_small_joiner_ram); - -/* Error out if the max bpp is less than smallest allowed valid bpp */ -if (bits_per_pixel < valid_dsc_bpp[0 ]) { -DRM_DEBUG_KMS ("Unsupported BPP %d\n" , bits_per_pixel); -return 0 ; - } - -/* Find the nearest match in the array of known BPPs from VESA */ -for (i =0 ; i <ARRAY_SIZE (valid_dsc_bpp) -1 ; i++) { -if (bits_per_pixel < valid_dsc_bpp[i +1 ]) -break ; - } - bits_per_pixel = valid_dsc_bpp[i]; - -/* -* Compressed BPP in U6.4 format so multiply by 16, for Gen 11, -* fractional part is 0 -*/ -return bits_per_pixel <<4 ; -} - -u8 intel_dp_dsc_get_slice_count (struct intel_dp *intel_dp, -int mode_clock, -int mode_hdisplay) -{ -u8 min_slice_count, i; -int max_slice_width; - -if (mode_clock <=DP_DSC_PEAK_PIXEL_RATE ) - min_slice_count =DIV_ROUND_UP (mode_clock, -DP_DSC_MAX_ENC_THROUGHPUT_0 ); -else - min_slice_count =DIV_ROUND_UP (mode_clock, -DP_DSC_MAX_ENC_THROUGHPUT_1 ); - - max_slice_width =drm_dp_dsc_sink_max_slice_width (intel_dp->dsc_dpcd); -if (max_slice_width <DP_DSC_MIN_SLICE_WIDTH_VALUE ) { -DRM_DEBUG_KMS ("Unsupported slice width %d by DP DSC Sink device\n" , - max_slice_width); -return 0 ; - } -/* Also take into account max slice width */ - min_slice_count =min_t (u8, min_slice_count, -DIV_ROUND_UP (mode_hdisplay, - max_slice_width)); - -/* Find the closest match to the valid slice count values */ -for (i =0 ; i <ARRAY_SIZE (valid_dsc_slicecount); i++) { -if (valid_dsc_slicecount[i] > -drm_dp_dsc_sink_max_slice_count (intel_dp->dsc_dpcd, - false)) -break ; -if (min_slice_count <= valid_dsc_slicecount[i]) -return valid_dsc_slicecount[i]; - } - -DRM_DEBUG_KMS ("Unsupported Slice Count %d\n" , min_slice_count); -return 0 ; -} -static void intel_pixel_encoding_setup_vsc (struct intel_dp *intel_dp,const struct intel_crtc_state *crtc_state)drivers/gpu/drm/i915/display/intel_dp.h +2
-4@@ -103,10 +103,6 @@ bool intel_dp_source_supports_hbr2(struct intel_dp *intel_dp);bool intel_dp_source_supports_hbr3 (struct intel_dp *intel_dp);bool intel_dp_get_link_status (struct intel_dp *intel_dp,u8 *link_status); -u16 intel_dp_dsc_get_output_bpp (int link_clock,u8 lane_count, -int mode_clock,int mode_hdisplay); -u8 intel_dp_dsc_get_slice_count (struct intel_dp *intel_dp,int mode_clock, -int mode_hdisplay);bool intel_dp_read_dpcd (struct intel_dp *intel_dp);bool intel_dp_get_colorimetry_status (struct intel_dp *intel_dp);@@ -119,4 +115,6 @@ static inline unsigned int intel_dp_unused_lane_mask(int lane_count) return ~((1 << lane_count) - 1) & 0xf; } +u32 intel_dp_mode_to_fec_clock (u32 mode_clock); +#endif /* __INTEL_DP_H__ */ drivers/gpu/drm/i915/display/intel_dp_mst.c +1
-1@@ -81,7 +81,7 @@ static int intel_dp_mst_compute_link_config(struct intel_encoder *encoder, adjusted_mode->crtc_clock, crtc_state->port_clock, &crtc_state->dp_m_n, - constant_n); + constant_n, crtc_state->fec_enable); crtc_state->dp_m_n.tu = slots;return 0 ;Signature · 6 lines
2.20.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 2 lines
Ville Syrjälä Intel
Op 25-09-2019 om 12:26 schreef Ville Syrjälä:
Quoted 116 lines · Maarten Lankhorst
Quoted 115 lines
There was a integer wraparound when
mode_clockbecame too high, and we didn't correct for the FEC overhead factor when dividing, with the calculations breaking at HBR3.As a result our calculated bpp was way too high, and the link width limitation never came into effect.
Print out the resulting bpp calcululations as a sanity check, just in case we ever have to debug it later on again.
We also used the wrong factor for FEC. While bspec mentions 2.4%, all the calculations use 1/0.972261, and the same ratio should be applied to data M/N as well, so use it there when FEC is enabled.
This fixes the FIFO underrun we are seeing with FEC enabled.
Changes since v2:
- Handlefec_enableinintel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogusfec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.Signed-off-by Maarten Lankhorst <[email protected]>Fixes d9218c8f6cf4 ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")Cc <[email protected]> # v5.0+Cc Manasi Navare <[email protected]>--- drivers/gpu/drm/i915/display/intel_display.c | 12 +- drivers/gpu/drm/i915/display/intel_display.h | 2 +- drivers/gpu/drm/i915/display/intel_dp.c | 184 ++++++++++--------- drivers/gpu/drm/i915/display/intel_dp.h | 6 +- drivers/gpu/drm/i915/display/intel_dp_mst.c | 2 +- 5 files changed, 107 insertions(+), 99 deletions(-)drivers/gpu/drm/i915/display/intel_display.c +8
-4@@ -7291,7 +7291,7 @@ static int ironlake_fdi_compute_config(struct intel_crtc *intel_crtc, pipe_config->fdi_lanes = lane;intel_link_compute_m_n (pipe_config->pipe_bpp, lane, fdi_dotclock, - link_bw, &pipe_config->fdi_m_n, false); + link_bw, &pipe_config->fdi_m_n, false, false); ret =ironlake_check_fdi_lanes (dev, intel_crtc->pipe, pipe_config);if (ret == -EDEADLK )@@ -7538,11 +7538,15 @@ void intel_link_compute_m_n(u16 bits_per_pixel, int nlanes, int pixel_clock, int link_clock, struct intel_link_m_n *m_n, - bool constant_n) + bool constant_n, bool fec_enable) { - m_n->tu = 64; + u32 data_clock = bits_per_pixel * pixel_clock; + +if (fec_enable) + data_clock =intel_dp_mode_to_fec_clock (data_clock); -compute_m_n (bits_per_pixel * pixel_clock, + m_n->tu =64 ; +compute_m_n (data_clock, link_clock * nlanes *8 , &m_n->gmch_m, &m_n->gmch_n, constant_n);drivers/gpu/drm/i915/display/intel_display.h +1
-1@@ -443,7 +443,7 @@ enum phy_fia {void intel_link_compute_m_n (u16 bpp,int nlanes,int pixel_clock,int link_clock,struct intel_link_m_n *m_n, -bool constant_n); +bool constant_n,bool fec_enable);bool is_ccs_modifier (u64 modifier);void lpt_disable_clkout_dp (struct drm_i915_private *dev_priv); u32 intel_plane_fb_max_stride(struct drm_i915_private *dev_priv,drivers/gpu/drm/i915/display/intel_dp.c +16
-2@@ -76,8 +76,8 @@#define DP_DSC_MAX_ENC_THROUGHPUT_0 340000#define DP_DSC_MAX_ENC_THROUGHPUT_1 400000 -/* DP DSC FEC Overhead factor = (100 - 2.4)/100 */ -#define DP_DSC_FEC_OVERHEAD_FACTOR 976 +/* DP DSC FEC Overhead factor = 1/(0.972261) */ +#define DP_DSC_FEC_OVERHEAD_FACTOR 972261/* Compliance test status bits */ #define INTEL_DP_RESOLUTION_SHIFT_MASK 0@@ -492,6 +492,97 @@ int intel_dp_get_link_train_fallback_values(struct intel_dp *intel_dp,return 0 ; } +u32 intel_dp_mode_to_fec_clock (u32 mode_clock) +{ +return div_u64 (mul_u32_u32 (mode_clock,1000000U ), +DP_DSC_FEC_OVERHEAD_FACTOR ); +} + +static u16 intel_dp_dsc_get_output_bpp (u32 link_clock,u32 lane_count, +u32 mode_clock,u32 mode_hdisplay) +{ +u32 bits_per_pixel, max_bpp_small_joiner_ram; +int i; + +/* +* Available Link Bandwidth(Kbits/sec) = (NumberOfLanes)*
Quoted 8 lines
drivers/gpu/drm/i915/display/intel_dp.c int intel_dp_get_link_train_fallback_values(struct intel_dp *intel_dp, · line 514
Quoted 6 lines
drivers/gpu/drm/i915/display/intel_dp.c +6
-0+* (LinkSymbolClock)* 8 * (TimeSlotsPerMTP) +* for SST -> TimeSlotsPerMTP is 1, +* for MST -> TimeSlotsPerMTP has to be calculated +*/ + bits_per_pixel = (link_clock * lane_count *8 ) / +intel_dp_mode_to_fec_clock (mode_clock);Hmm. Aren't we adding the FEC overhead twice now when DSC is also enabled?
No? This is calculating the maximum bpp that can be used for DSC.
"For cases where FEC is enabled, pixel clock is replaced by pixel clock/0.972261 in the above calculations."
This bpp check here is to ensure that data M <= N.
~Maarten
Ville Syrjälä
Reviewed-byQuoted 126 lines · Maarten Lankhorst
Op 25-09-2019 om 12:26 schreef Ville Syrjälä:
Quoted 116 lines · Maarten Lankhorst
Quoted 115 lines
There was a integer wraparound when
mode_clockbecame too high, and we didn't correct for the FEC overhead factor when dividing, with the calculations breaking at HBR3.As a result our calculated bpp was way too high, and the link width limitation never came into effect.
Print out the resulting bpp calcululations as a sanity check, just in case we ever have to debug it later on again.
We also used the wrong factor for FEC. While bspec mentions 2.4%, all the calculations use 1/0.972261, and the same ratio should be applied to data M/N as well, so use it there when FEC is enabled.
This fixes the FIFO underrun we are seeing with FEC enabled.
Changes since v2:
- Handlefec_enableinintel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogusfec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.Signed-off-by Maarten Lankhorst <[email protected]>Fixes d9218c8f6cf4 ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")Cc <[email protected]> # v5.0+Cc Manasi Navare <[email protected]>--- drivers/gpu/drm/i915/display/intel_display.c | 12 +- drivers/gpu/drm/i915/display/intel_display.h | 2 +- drivers/gpu/drm/i915/display/intel_dp.c | 184 ++++++++++--------- drivers/gpu/drm/i915/display/intel_dp.h | 6 +- drivers/gpu/drm/i915/display/intel_dp_mst.c | 2 +- 5 files changed, 107 insertions(+), 99 deletions(-)drivers/gpu/drm/i915/display/intel_display.c +8
-4@@ -7291,7 +7291,7 @@ static int ironlake_fdi_compute_config(struct intel_crtc *intel_crtc, pipe_config->fdi_lanes = lane;intel_link_compute_m_n (pipe_config->pipe_bpp, lane, fdi_dotclock, - link_bw, &pipe_config->fdi_m_n, false); + link_bw, &pipe_config->fdi_m_n, false, false); ret =ironlake_check_fdi_lanes (dev, intel_crtc->pipe, pipe_config);if (ret == -EDEADLK )@@ -7538,11 +7538,15 @@ void intel_link_compute_m_n(u16 bits_per_pixel, int nlanes, int pixel_clock, int link_clock, struct intel_link_m_n *m_n, - bool constant_n) + bool constant_n, bool fec_enable) { - m_n->tu = 64; + u32 data_clock = bits_per_pixel * pixel_clock; + +if (fec_enable) + data_clock =intel_dp_mode_to_fec_clock (data_clock); -compute_m_n (bits_per_pixel * pixel_clock, + m_n->tu =64 ; +compute_m_n (data_clock, link_clock * nlanes *8 , &m_n->gmch_m, &m_n->gmch_n, constant_n);drivers/gpu/drm/i915/display/intel_display.h +1
-1@@ -443,7 +443,7 @@ enum phy_fia {void intel_link_compute_m_n (u16 bpp,int nlanes,int pixel_clock,int link_clock,struct intel_link_m_n *m_n, -bool constant_n); +bool constant_n,bool fec_enable);bool is_ccs_modifier (u64 modifier);void lpt_disable_clkout_dp (struct drm_i915_private *dev_priv); u32 intel_plane_fb_max_stride(struct drm_i915_private *dev_priv,drivers/gpu/drm/i915/display/intel_dp.c +16
-2@@ -76,8 +76,8 @@#define DP_DSC_MAX_ENC_THROUGHPUT_0 340000#define DP_DSC_MAX_ENC_THROUGHPUT_1 400000 -/* DP DSC FEC Overhead factor = (100 - 2.4)/100 */ -#define DP_DSC_FEC_OVERHEAD_FACTOR 976 +/* DP DSC FEC Overhead factor = 1/(0.972261) */ +#define DP_DSC_FEC_OVERHEAD_FACTOR 972261/* Compliance test status bits */ #define INTEL_DP_RESOLUTION_SHIFT_MASK 0@@ -492,6 +492,97 @@ int intel_dp_get_link_train_fallback_values(struct intel_dp *intel_dp,return 0 ; } +u32 intel_dp_mode_to_fec_clock (u32 mode_clock) +{ +return div_u64 (mul_u32_u32 (mode_clock,1000000U ), +DP_DSC_FEC_OVERHEAD_FACTOR ); +} + +static u16 intel_dp_dsc_get_output_bpp (u32 link_clock,u32 lane_count, +u32 mode_clock,u32 mode_hdisplay) +{ +u32 bits_per_pixel, max_bpp_small_joiner_ram; +int i; + +/* +* Available Link Bandwidth(Kbits/sec) = (NumberOfLanes)* Quoted 8 lines
drivers/gpu/drm/i915/display/intel_dp.c int intel_dp_get_link_train_fallback_values(struct intel_dp *intel_dp, · line 514
Quoted 6 lines
drivers/gpu/drm/i915/display/intel_dp.c +6
-0+* (LinkSymbolClock)* 8 * (TimeSlotsPerMTP) +* for SST -> TimeSlotsPerMTP is 1, +* for MST -> TimeSlotsPerMTP has to be calculated +*/ + bits_per_pixel = (link_clock * lane_count *8 ) / +intel_dp_mode_to_fec_clock (mode_clock);Hmm. Aren't we adding the FEC overhead twice now when DSC is also enabled?
Quoted 1 line
No? This is calculating the maximum bpp that can be used for DSC.
Ah, right. Seems fine then.
Series is
Quoted 6 lines
"For cases where FEC is enabled, pixel clock is replaced by pixel clock/0.972261 in the above calculations."
This bpp check here is to ensure that data M <= N.
~Maarten
Signature · 2 lines
Ville Syrjälä Intel
Sasha Levin
maintainerHi,
[This is an automated email]
This commit has been processed because it contains a "Fixes:" tag,
fixing commit: d9218c8f6cf4 drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC.
The bot has tested the following trees: v5.3.1, v5.2.17.
v5.3.1: Build OK!
v5.2.17: Failed to apply! Possible dependencies:
3c053a96ef5f ("drm/i915/dp: Program VSC Header and DB for Pixel Encoding/Colorimetry Format")
NOTE: The patch will not be queued to stable trees until it is upstream.
How should we proceed with this patch?
--
Thanks,
Sasha
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.IGT: success for series starting with [1/2] drm/i915/dp: Fix dsc bpp calculations, v5.
In reply to Maarten Lankhorst== Series Details ==
== Series Details ==
Series: series starting with [1/2] drm/i915/dp: Fix dsc bpp calculations, v5.
URL : https://patchwork.freedesktop.org/series/67203/
State : success
== Summary ==
CI Bug Log - changes from CI_DRM_6954_full -> Patchwork_14526_full
====================================================
Summary
-------
**SUCCESS**
No regressions found.
Known issues
------------
Here are the changes found in Patchwork_14526_full that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@gem_ctx_shared@exec-single-timeline-bsd1:
- shard-iclb: [PASS][1] -> [SKIP][2] ([fdo#109276]) +14 similar issues
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-iclb4/igt@[email protected]
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-iclb8/igt@[email protected]
* igt@gem_ctx_switch@bcs0-heavy-queue:
- shard-apl: [PASS][3] -> [INCOMPLETE][4] ([fdo#103927])
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-apl8/igt@[email protected]
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-apl7/igt@[email protected]
* igt@gem_eio@in-flight-suspend:
- shard-apl: [PASS][5] -> [DMESG-WARN][6] ([fdo#108566]) +1 similar issue
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-apl2/igt@[email protected]
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-apl5/igt@[email protected]
* igt@gem_exec_schedule@wide-bsd:
- shard-iclb: [PASS][7] -> [SKIP][8] ([fdo#111325]) +3 similar issues
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-iclb8/igt@[email protected]
[8]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-iclb4/igt@[email protected]
* igt@gem_tiled_swapping@non-threaded:
- shard-apl: [PASS][9] -> [DMESG-WARN][10] ([fdo#108686])
[9]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-apl7/igt@[email protected]
[10]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-apl2/igt@[email protected]
* igt@i915_suspend@debugfs-reader:
- shard-kbl: [PASS][11] -> [DMESG-WARN][12] ([fdo#108566])
[11]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-kbl4/igt@[email protected]
[12]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-kbl3/igt@[email protected]
* igt@kms_draw_crc@draw-method-rgb565-render-xtiled:
- shard-skl: [PASS][13] -> [FAIL][14] ([fdo#103184] / [fdo#103232])
[13]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-skl10/igt@[email protected]
[14]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-skl4/igt@[email protected]
* igt@kms_flip@2x-plain-flip-fb-recreate-interruptible:
- shard-glk: [PASS][15] -> [FAIL][16] ([fdo#100368])
[15]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-glk7/igt@[email protected]
[16]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-glk5/igt@[email protected]
* igt@kms_flip@flip-vs-suspend:
- shard-skl: [PASS][17] -> [INCOMPLETE][18] ([fdo#109507])
[17]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-skl6/igt@[email protected]
[18]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-skl3/igt@[email protected]
* igt@kms_frontbuffer_tracking@fbc-1p-offscren-pri-indfb-draw-render:
- shard-iclb: [PASS][19] -> [FAIL][20] ([fdo#103167]) +4 similar issues
[19]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-iclb2/igt@kms_frontbuffer_tracking@fbc-1p-offscren-pri-indfb-draw-render.html
[20]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-iclb2/igt@kms_frontbuffer_tracking@fbc-1p-offscren-pri-indfb-draw-render.html
#### Possible fixes ####
* igt@gem_ctx_isolation@rcs0-s3:
- shard-apl: [DMESG-WARN][21] ([fdo#108566]) -> [PASS][22] +6 similar issues
[21]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-apl6/igt@[email protected]
[22]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-apl6/igt@[email protected]
* igt@gem_ctx_shared@exec-single-timeline-bsd:
- shard-iclb: [SKIP][23] ([fdo#110841]) -> [PASS][24]
[23]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-iclb1/igt@[email protected]
[24]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-iclb6/igt@[email protected]
* igt@gem_exec_parallel@contexts:
- shard-skl: [DMESG-WARN][25] ([fdo#106107]) -> [PASS][26]
[25]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-skl10/igt@[email protected]
[26]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-skl4/igt@[email protected]
* igt@gem_exec_schedule@preempt-queue-bsd1:
- shard-iclb: [SKIP][27] ([fdo#109276]) -> [PASS][28] +11 similar issues
[27]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-iclb8/igt@[email protected]
[28]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-iclb4/igt@[email protected]
* igt@gem_exec_schedule@preempt-queue-contexts-chain-bsd:
- shard-iclb: [SKIP][29] ([fdo#111325]) -> [PASS][30] +3 similar issues
[29]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-iclb4/igt@[email protected]
[30]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-iclb7/igt@[email protected]
* igt@kms_cursor_edge_walk@pipe-c-256x256-top-edge:
- shard-apl: [TIMEOUT][31] ([fdo#111800]) -> [PASS][32]
[31]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-apl7/igt@[email protected]
[32]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-apl2/igt@[email protected]
* igt@kms_flip@2x-flip-vs-expired-vblank-interruptible:
- shard-glk: [FAIL][33] ([fdo#105363]) -> [PASS][34]
[33]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-glk1/igt@[email protected]
[34]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-glk2/igt@[email protected]
* igt@kms_flip@flip-vs-suspend-interruptible:
- shard-skl: [INCOMPLETE][35] ([fdo#109507]) -> [PASS][36]
[35]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-skl9/igt@[email protected]
[36]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-skl10/igt@[email protected]
* igt@kms_frontbuffer_tracking@fbc-badstride:
- shard-iclb: [FAIL][37] ([fdo#103167]) -> [PASS][38] +2 similar issues
[37]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-iclb5/igt@[email protected]
[38]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-iclb7/igt@[email protected]
* igt@kms_pipe_crc_basic@suspend-read-crc-pipe-a:
- shard-iclb: [DMESG-WARN][39] ([fdo#111764]) -> [PASS][40]
[39]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-iclb1/igt@[email protected]
[40]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-iclb3/igt@[email protected]
* igt@kms_plane_alpha_blend@pipe-b-constant-alpha-min:
- shard-skl: [FAIL][41] ([fdo#108145]) -> [PASS][42]
[41]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-skl3/igt@[email protected]
[42]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-skl6/igt@[email protected]
* igt@kms_plane_alpha_blend@pipe-b-coverage-7efc:
- shard-skl: [FAIL][43] ([fdo#108145] / [fdo#110403]) -> [PASS][44]
[43]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-skl10/igt@[email protected]
[44]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-skl4/igt@[email protected]
* igt@kms_psr@psr2_sprite_mmap_gtt:
- shard-iclb: [SKIP][45] ([fdo#109441]) -> [PASS][46] +1 similar issue
[45]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-iclb8/igt@kms_psr@psr2_sprite_mmap_gtt.html
[46]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-iclb2/igt@kms_psr@psr2_sprite_mmap_gtt.html
* igt@kms_vblank@pipe-c-ts-continuation-dpms-suspend:
- shard-skl: [INCOMPLETE][47] ([fdo#104108]) -> [PASS][48]
[47]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-skl9/igt@[email protected]
[48]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-skl2/igt@[email protected]
* igt@perf@gen8-unprivileged-single-ctx-counters:
- shard-skl: [DMESG-FAIL][49] -> [PASS][50]
[49]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-skl10/igt@[email protected]
[50]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-skl4/igt@[email protected]
* igt@perf_pmu@cpu-hotplug:
- shard-apl: [TIMEOUT][51] ([fdo#111546] / [fdo#111800]) -> [PASS][52]
[51]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-apl7/igt@[email protected]
[52]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-apl2/igt@[email protected]
#### Warnings ####
* igt@gem_mocs_settings@mocs-isolation-bsd2:
- shard-iclb: [FAIL][53] ([fdo#111330]) -> [SKIP][54] ([fdo#109276])
[53]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_6954/shard-iclb4/igt@[email protected]
[54]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/shard-iclb8/igt@[email protected]
[fdo#100368]: https://bugs.freedesktop.org/show_bug.cgi?id=100368
[fdo#103167]: https://bugs.freedesktop.org/show_bug.cgi?id=103167
[fdo#103184]: https://bugs.freedesktop.org/show_bug.cgi?id=103184
[fdo#103232]: https://bugs.freedesktop.org/show_bug.cgi?id=103232
[fdo#103927]: https://bugs.freedesktop.org/show_bug.cgi?id=103927
[fdo#104108]: https://bugs.freedesktop.org/show_bug.cgi?id=104108
[fdo#105363]: https://bugs.freedesktop.org/show_bug.cgi?id=105363
[fdo#106107]: https://bugs.freedesktop.org/show_bug.cgi?id=106107
[fdo#108145]: https://bugs.freedesktop.org/show_bug.cgi?id=108145
[fdo#108566]: https://bugs.freedesktop.org/show_bug.cgi?id=108566
[fdo#108686]: https://bugs.freedesktop.org/show_bug.cgi?id=108686
[fdo#109276]: https://bugs.freedesktop.org/show_bug.cgi?id=109276
[fdo#109441]: https://bugs.freedesktop.org/show_bug.cgi?id=109441
[fdo#109507]: https://bugs.freedesktop.org/show_bug.cgi?id=109507
[fdo#110403]: https://bugs.freedesktop.org/show_bug.cgi?id=110403
[fdo#110841]: https://bugs.freedesktop.org/show_bug.cgi?id=110841
[fdo#111325]: https://bugs.freedesktop.org/show_bug.cgi?id=111325
[fdo#111330]: https://bugs.freedesktop.org/show_bug.cgi?id=111330
[fdo#111546]: https://bugs.freedesktop.org/show_bug.cgi?id=111546
[fdo#111764]: https://bugs.freedesktop.org/show_bug.cgi?id=111764
[fdo#111800]: https://bugs.freedesktop.org/show_bug.cgi?id=111800
Participating hosts (9 -> 9)
------------------------------
No changes in participating hosts
Build changes
-------------
* CI: CI-20190529 -> None
* Linux: CI_DRM_6954 -> Patchwork_14526
CI-20190529: 20190529
CI_DRM_6954: 80fa0e042cdb3da59d2c738db61b8da78cf29e0d @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_5202: 3499c5eb17054e2abd88023fe962768140d24302 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_14526: 43fc9a688962d5678e6dfd105530a519b5b7e935 @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14526/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx