Skip to contentSkip to conversation

iio: temperature: Add support for LTC2983

PATCH RESEND Superseded Nuno Sá 2 participants 6 messages Sep 30, 2019 – Oct 2, 2019

Subsystems (4)

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore

Nuno Sá

author maintainer
#0 lore raw

PATCH RESEND v2 1/2 iio: temperature: Add support for LTC2983

The LTC2983 is a Multi-Sensor High Accuracy Digital Temperature Measurement System. It measures a wide variety of temperature sensors and digitally outputs the result, in °C or °F, with 0.1°C accuracy and 0.001°C resolution. It can measure the temperature of all standard thermocouples (type B,E,J,K,N,S,R,T), standard 2-,3-,4-wire RTDs, thermistors and diodes.

---
Changes in v2:
* Added some needed blank lines (for readability);
* Allocate iio_chan in the setup() function;
* Rename reset to sleep;
* Remove unneeded dev_dbg calls;
* Remove unneeded line wrapping;
* Remove unneeded comments;
* Remove extend_names. Use the standard ABI;
* Adapt the scales to report in millivolt and milli degrees;
* Adapt the of_property readings to the renaming of the properties;
* For custom thermistors, excitation-current cannot be set to Auto range.

 MAINTAINERS                       |    7 +
 drivers/iio/temperature/Kconfig   |   10 +
 drivers/iio/temperature/Makefile  |    1 +
 drivers/iio/temperature/ltc2983.c | 1436 +++++++++++++++++++++++++++++
 4 files changed, 1454 insertions(+)
 create mode 100644 drivers/iio/temperature/ltc2983.c
MAINTAINERS +7 -0
index f0c03740b9fb..14a256e785ca 100644
@@ -9491,6 +9491,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/iio/dac/ltc1660.txt
 F:	drivers/iio/dac/ltc1660.c
 
+LTC2983 IIO TEMPERATURE DRIVER
+M:	Nuno Sá <[email protected]>
+W:	http://ez.analog.com/community/linux-device-drivers
+L:	[email protected]
+S:	Supported
+F:	drivers/iio/temperature/ltc2983.c
+
 LTC4261 HARDWARE MONITOR DRIVER
 M:	Guenter Roeck <[email protected]>
 L:	[email protected]
drivers/iio/temperature/Kconfig +10 -0
index 737faa0901fe..04b5a67b593c 100644
@@ -4,6 +4,16 @@
 #
 menu "Temperature sensors"
 
+config LTC2983
+	tristate "Analog Devices Multi-Sensor Digital Temperature Measurement System"
+	depends on SPI
+	help
+	  Say yes here to build support for the LTC2983 Multi-Sensor
+	  high accuracy digital temperature measurement system.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called ltc2983.
+
 config MAXIM_THERMOCOUPLE
 	tristate "Maxim thermocouple sensors"
 	depends on SPI
drivers/iio/temperature/Makefile +1 -0
index baca4776ca0d..d6b850b0cf63 100644
@@ -3,6 +3,7 @@
 # Makefile for industrial I/O temperature drivers
 #
 
+obj-$(CONFIG_LTC2983) += ltc2983.o
 obj-$(CONFIG_HID_SENSOR_TEMP) += hid-sensor-temperature.o
 obj-$(CONFIG_MAXIM_THERMOCOUPLE) += maxim_thermocouple.o
 obj-$(CONFIG_MAX31856) += max31856.o
drivers/iio/temperature/ltc2983.c new file +1436 -0

1,436 lines not on this page · raw message

Signature · 1 line
2.23.0
author maintainer
#1 lore raw

PATCH RESEND v2 2/2 dt-bindings: iio: Add ltc2983 documentation

Document the LTC2983 temperature sensor devicetree bindings.

---
Changes in v2:
* Drop maxItems in non-array elements;
* Set adi,mux-delay-config-us instead of adi,mux-delay-config;
* Wrapped lines at 80 char;
* Added comas to enum elements;
* Use real units in adi,excitation-current;
* Moved some enums to minimum and maximum;
* Grouped patternProperties and moved reg property as a generic property.

 .../bindings/iio/temperature/adi,ltc2983.yaml | 406 ++++++++++++++++++
 MAINTAINERS                                   |   1 +
 2 files changed, 407 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +406 -0
new file mode 100644
index 000000000000..df68b8233e5e
@@ -0,0 +1,406 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/temperature/adi,ltc2983.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices LTC2983 Multi-sensor Temperature system
+
+maintainers:
+  - Nuno Sá <[email protected]>
+
+description: |
+  Analog Devices LTC2983 Multi-Sensor Digital Temperature Measurement System
+  https://www.analog.com/media/en/technical-documentation/data-sheets/2983fc.pdf
+
+properties:
+  compatible:
+    enum:
+      - adi,ltc2983
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  adi,temperature-celcius:
+    description:
+      If this property is present, the temperature is reported in Celsius.
+    type: boolean
+
+  adi,mux-delay-config-us:
+    description:
+      The LTC2983 performs 2 or 3 internal conversion cycles per temperature
+      result. Each conversion cycle is performed with different excitation and
+      input multiplexer configurations. Prior to each conversion, these
+      excitation circuits and input switch configurations are changed and an
+      internal 1ms delay ensures settling prior to the conversion cycle in most
+      cases. An extra delay can be configured using this property. The value is
+      rounded to nearest 100us.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - maximum: 255
+
+  adi,filter-notch-freq:
+    description:
+      Set's the default setting of the digital filter. The default is
+      simultaneous 50/60Hz rejection.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
+      - maximum: 2
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+patternProperties:
+  ".*@([1-9]|1[0-9]|20)$":
+    type: object
+
+    properties:
+      reg:
+        description: |
+          The channel number. It can be connected to one of the 20 channels of
+          the device.
+        minimum: 1
+        maximum: 20
+
+    required:
+      - reg
+
+    patternProperties:
+      "^thermocouple@.*":
+        type: object
+        description: |
+          Represents a thermocouple sensor which is connected to one of the device
+          channels.
+
+        properties:
+          adi,sensor-type:
+            description: |
+              Identifies the type of thermocouple connected to the device.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 1
+              - maximum: 8
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look at table 14
+              of the datasheet for how to set this value for thermocouples.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 1
+              - maximun: 15
+
+          adi,cold-junction-handle:
+            description: |
+              Phandle which points to a sensor object responsible for measuring
+              the thermocouple cold junction temperature.
+            $ref: "/schemas/types.yaml#/definitions/phandle"
+
+          adi,custom-sensor:
+            description: |
+              This is a table, where each entry should be a pair of
+              voltage(mv)-temperature(K). The entries must be given in nv and uK
+              so that, the original values must be multiplied by 1000000. For
+              more details look at table 69 and 70.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/int64-array
+              - minItems: 6
+              - maxItems: 128
+
+        required:
+          - adi,sensor-type
+
+      "^diode@.*":
+        type: object
+        description: |
+          Represents a diode sensor which is connected to one of the device
+          channels.
+
+        properties:
+          adi,sensor-type:
+            description: Identifies the sensor as a diode.
+            const: 28
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look at table 17
+              of the datasheet for how to set this value for diodes.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 0
+              - maximum: 7
+
+          adi,excitation-current-microamp:
+            description: |
+              This property controls the magnitude of the excitation current
+              applied to the diode. Depending on the number of conversions
+              cycles, this property will assume different predefined values on
+              each cycle. Just set the value of the first cycle (1l).
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [10, 20, 40, 80]
+
+          adi,ideal-factor-value:
+            description: |
+              This property sets the diode ideality factor. The real value must
+              be multiplied by 1000000 to remove the fractional part. For more
+              information look at table 20 of the datasheet.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+
+        required:
+          - adi,sensor-type
+
+      "^rtd@.*":
+        type: object
+        description: |
+          Represents a rtd sensor which is connected to one of the device channels.
+
+        properties:
+          reg:
+            minimum: 2
+
+          adi,sensor-type:
+            description: Identifies the type of RTD connected to the device.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 10
+              - maximum: 17
+
+          adi,rsense-handle:
+            description: |
+              Phandle pointing to a rsense object associated with this RTD.
+            $ref: "/schemas/types.yaml#/definitions/phandle"
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look at table 28
+              of the datasheet for how to set this value for RTD's.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [0, 1, 4, 5, 8, 9, 10, 12, 13, 14]
+
+          adi,excitation-current-microamp:
+            description: |
+              This property controls the magnitude of the excitation current
+              applied to the RTD.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [5, 10, 25, 50, 100, 250, 500, 1000]
+
+          adi,rtd-curve:
+            description: |
+              This property set the RTD curve used and the corresponding
+              Callendar-VanDusen constants. Look at table 30 of the datasheet.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 0
+              - maximum: 3
+
+          adi,custom-sensor:
+            description: |
+              This is a table, where each entry should be a pair of
+              resistance(ohm)-temperature(K). The entries added here are in uohm
+              and uK. For more details values look at table 74 and 75.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64-array
+              - minItems: 6
+              - maxItems: 128
+
+        required:
+          - adi,sensor-type
+          - adi,rsense-handle
+
+      "^thermistor@.*":
+        type: object
+        description: |
+          Represents a thermistor sensor which is connected to one of the device
+          channels.
+
+        properties:
+          adi,sensor-type:
+            description: |
+              Identifies the type of thermistor connected to the
+              device.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 19
+              - maximum: 25
+
+          adi,rsense-handle:
+            description: |
+              Phandle pointing to a rsense object associated with this
+              thermistor.
+            $ref: "/schemas/types.yaml#/definitions/phandle"
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look at table 52
+              of the datasheet for how to set this value for thermistors.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 0
+              - maximum: 4
+
+          adi,excitation-current-nanoamp:
+            description: |
+              This property controls the magnitude of the excitation current
+              applied to the thermistor. Value 0 set's the sensor in auto-range
+              mode.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [0, 250, 500, 1000, 5000, 10000, 25000, 50000, 100000,
+                       250000, 500000, 1000000]
+
+          adi,custom-sensor:
+            description: |
+              This is a table, where each entry should be a pair of
+              resistance(ohm)-temperature(K). The entries added here are in uohm
+              and uK only for custom thermistors. For more details look at table
+              78 and 79. Steinhart-Hart coefficients are also supported and can
+              be programmed into the device memory using this property. For
+              Steinhart sensors, this table has a constant size of 6 entries
+              (defining the coefficients) and the values are given in the raw
+              format. Look at table 82 for more information.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64-array
+              - minItems: 6
+              - maxItems: 128
+
+        required:
+          - adi,sensor-type
+          - adi,rsense-handle
+
+      "^adc@.*":
+        type: object
+        description: Represents a channel which is being used as a direct adc.
+
+        properties:
+          adi,sensor-type:
+            description: Identifies the sensor as a direct adc.
+            const: 30
+
+          adi,single-ended:
+            description: Boolean property which set's the adc as single-ended.
+            type: boolean
+
+        required:
+          - adi,sensor-type
+
+      "^rsense@.*":
+        type: object
+        description: |
+          Represents a rsense which is connected to one of the device channels.
+          Rsense are used by thermistors and RTD's.
+
+        properties:
+          reg:
+            minimum: 2
+
+          adi,sensor-type:
+            description: Identifies the sensor as a rsense.
+            const: 29
+
+          adi,rsense-val-micro-ohms:
+            description: |
+              Sets the value of the sense resistor. Look at table 20 of the
+              datasheet for information.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64
+
+        required:
+          - adi,sensor-type
+          - adi, rsense-val
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spi0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        sensor_ltc2983: ltc2983@0 {
+                compatible = "adi,ltc2983";
+                reg = <0>;
+
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                adi,temperature-celcius;
+                interrupts = <20 IRQ_TYPE_EDGE_RISING>;
+                interrupt-parent = <&gpio>;
+
+                thermocouple@18 {
+                        reg = <18>;
+                        adi,sensor-type = <8>; //Type B
+                        adi,sensor-config = <1>; //Differential, open-circuit current
+                        adi,cold-junction-handle = <&diode5>;
+                };
+
+                diode5: diode@5 {
+                        reg = <5>;
+                        adi,sensor-type = <28>;
+                };
+
+                rsense2: rsense@2 {
+                        reg = <2>;
+                        adi,sensor-type = <29>;
+                        adi,rsense-val-micro-ohms = /bits/ 64 <1200000000>; //1.2Kohms
+                };
+
+                rtd@14 {
+                        reg = <14>;
+                        adi,sensor-type = <15>; //PT1000
+                        /*2-wire, internal gnd, no current rotation*/
+                        adi,sensor-config = <1>;
+                        adi,excitation-current = <7>; //500uA
+                        adi,rsense-handle = <&rsense2>;
+                };
+
+                adc@10 {
+                        reg = <10>;
+                        adi,sensor-type = <30>;
+                        adi,single-ended;
+                };
+
+                thermistor@12 {
+                        reg = <12>;
+                        adi,sensor-type = <26>; //Steinhart
+                        adi,rsense-handle = <&rsense2>;
+                        adi,custom-sensor = /bits/ 64 <0x00F371EC 0x12345678
+                                        0x2C0F8733 0x10018C66 0xA0FEACCD
+                                        0x90021D99>; //6 entries
+                };
+
+                thermocouple@20 {
+                        reg = <20>;
+                        adi,sensor-type = <9>; //custom thermocouple
+                        adi,sensor-config = <8>; //single-ended
+                        adi,custom-sensor = /bits/ 64
+                                 <(-50220000) 0
+                                  (-30200000) 99100000
+                                  (-5300000) 135400000
+                                  0 273150000
+                                  40200000 361200000
+                                  55300000 522100000
+                                  88300000 720300000
+                                  132200000 811200000
+                                  188700000 922500000
+                                  460400000 1000000000>; //10 pairs
+               };
+
+        };
+    };
+...
MAINTAINERS +1 -0
index 14a256e785ca..f747a9dc27f5 100644
@@ -9497,6 +9497,7 @@ W:	http://ez.analog.com/community/linux-device-drivers
 L:	[email protected]
 S:	Supported
 F:	drivers/iio/temperature/ltc2983.c
+F:	Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml
 
 LTC4261 HARDWARE MONITOR DRIVER
 M:	Guenter Roeck <[email protected]>
Signature · 1 line
2.23.0
maintainer
#2 lore raw

Re: [RESEND PATCH v2 2/2] dt-bindings: iio: Add ltc2983 documentation

Quoted 3 lines · On Mon, 30 Sep 2019 12:42:47 +0200 Nuno Sá <[email protected]> wrote:

Document the LTC2983 temperature sensor devicetree bindings.

Hi Nuno,

A few comments inline. This is a complex one so I'll definitely be looking for a review from Rob or Mark,

Thanks,

Jonathan

Quoted 63 lines

---
Changes in v2:
* Drop maxItems in non-array elements;
* Set adi,mux-delay-config-us instead of adi,mux-delay-config;
* Wrapped lines at 80 char;
* Added comas to enum elements;
* Use real units in adi,excitation-current;
* Moved some enums to minimum and maximum;
* Grouped patternProperties and moved reg property as a generic property.

 .../bindings/iio/temperature/adi,ltc2983.yaml | 406 ++++++++++++++++++
 MAINTAINERS                                   |   1 +
 2 files changed, 407 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +42 -0
new file mode 100644
index 000000000000..df68b8233e5e
@@ -0,0 +1,406 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/temperature/adi,ltc2983.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices LTC2983 Multi-sensor Temperature system
+
+maintainers:
+  - Nuno Sá <[email protected]>
+
+description: |
+  Analog Devices LTC2983 Multi-Sensor Digital Temperature Measurement System
+  https://www.analog.com/media/en/technical-documentation/data-sheets/2983fc.pdf
+
+properties:
+  compatible:
+    enum:
+      - adi,ltc2983
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  adi,temperature-celcius:
+    description:
+      If this property is present, the temperature is reported in Celsius.
+    type: boolean
+
+  adi,mux-delay-config-us:
+    description:
+      The LTC2983 performs 2 or 3 internal conversion cycles per temperature
+      result. Each conversion cycle is performed with different excitation and
+      input multiplexer configurations. Prior to each conversion, these
+      excitation circuits and input switch configurations are changed and an
+      internal 1ms delay ensures settling prior to the conversion cycle in most
+      cases. An extra delay can be configured using this property. The value is
+      rounded to nearest 100us.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 52

Quoted 10 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +10 -0
+      - maximum: 255
+
+  adi,filter-notch-freq:
+    description:
+      Set's the default setting of the digital filter. The default is
+      simultaneous 50/60Hz rejection.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
+      - maximum: 2

This one is an oddity and you should define what the 3 values mean. If the sensor had supported no notch rejection at all rather than just 50, 60, 50/60 I would have suggested two bools but as it stands I guess this will just need to be an enum.

Quoted 27 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +27 -0
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+patternProperties:
+  ".*@([1-9]|1[0-9]|20)$":
+    type: object
+
+    properties:
+      reg:
+        description: |
+          The channel number. It can be connected to one of the 20 channels of
+          the device.
+        minimum: 1
+        maximum: 20
+
+    required:
+      - reg
+
+    patternProperties:
+      "^thermocouple@.*":
+        type: object
+        description: |
+          Represents a thermocouple sensor which is connected to one of the device

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 89

Quoted 10 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +10 -0
+          channels.
+
+        properties:
+          adi,sensor-type:
+            description: |
+              Identifies the type of thermocouple connected to the device.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 1
+              - maximum: 8

Meaning of values should be defined...

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 98

Quoted 9 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +9 -0
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look at table 14
+              of the datasheet for how to set this value for thermocouples.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 1
+              - maximun: 15

Hmm. Whilst there are quite a few things in here, it would be nice to break it up into human readable elements. It's only 3 things and there are a bunch of don't care states it seems.

Quoted 30 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +30 -0
+
+          adi,cold-junction-handle:
+            description: |
+              Phandle which points to a sensor object responsible for measuring
+              the thermocouple cold junction temperature.
+            $ref: "/schemas/types.yaml#/definitions/phandle"
+
+          adi,custom-sensor:
+            description: |
+              This is a table, where each entry should be a pair of
+              voltage(mv)-temperature(K). The entries must be given in nv and uK
+              so that, the original values must be multiplied by 1000000. For
+              more details look at table 69 and 70.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/int64-array
+              - minItems: 6
+              - maxItems: 128
+
+        required:
+          - adi,sensor-type
+
+      "^diode@.*":
+        type: object
+        description: |
+          Represents a diode sensor which is connected to one of the device
+          channels.
+
+        properties:
+          adi,sensor-type:
+            description: Identifies the sensor as a diode.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 138

Quoted 10 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +10 -0
+            const: 28
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look at table 17
+              of the datasheet for how to set this value for diodes.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 0
+              - maximum: 7

Another one I'd like to see broken up.

Quoted 40 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +40 -0
+
+          adi,excitation-current-microamp:
+            description: |
+              This property controls the magnitude of the excitation current
+              applied to the diode. Depending on the number of conversions
+              cycles, this property will assume different predefined values on
+              each cycle. Just set the value of the first cycle (1l).
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [10, 20, 40, 80]
+
+          adi,ideal-factor-value:
+            description: |
+              This property sets the diode ideality factor. The real value must
+              be multiplied by 1000000 to remove the fractional part. For more
+              information look at table 20 of the datasheet.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+
+        required:
+          - adi,sensor-type
+
+      "^rtd@.*":
+        type: object
+        description: |
+          Represents a rtd sensor which is connected to one of the device channels.
+
+        properties:
+          reg:
+            minimum: 2
+
+          adi,sensor-type:
+            description: Identifies the type of RTD connected to the device.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 10
+              - maximum: 17
+
+          adi,rsense-handle:
+            description: |

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 188

Quoted 10 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +10 -0
+              Phandle pointing to a rsense object associated with this RTD.
+            $ref: "/schemas/types.yaml#/definitions/phandle"
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look at table 28
+              of the datasheet for how to set this value for RTD's.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [0, 1, 4, 5, 8, 9, 10, 12, 13, 14]

Another one to break up into it's parts, which would also get rid of the enum with gaps element.

Quoted 52 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +52 -0
+
+          adi,excitation-current-microamp:
+            description: |
+              This property controls the magnitude of the excitation current
+              applied to the RTD.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [5, 10, 25, 50, 100, 250, 500, 1000]
+
+          adi,rtd-curve:
+            description: |
+              This property set the RTD curve used and the corresponding
+              Callendar-VanDusen constants. Look at table 30 of the datasheet.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 0
+              - maximum: 3
+
+          adi,custom-sensor:
+            description: |
+              This is a table, where each entry should be a pair of
+              resistance(ohm)-temperature(K). The entries added here are in uohm
+              and uK. For more details values look at table 74 and 75.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64-array
+              - minItems: 6
+              - maxItems: 128
+
+        required:
+          - adi,sensor-type
+          - adi,rsense-handle
+
+      "^thermistor@.*":
+        type: object
+        description: |
+          Represents a thermistor sensor which is connected to one of the device
+          channels.
+
+        properties:
+          adi,sensor-type:
+            description: |
+              Identifies the type of thermistor connected to the
+              device.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 19
+              - maximum: 25
+
+          adi,rsense-handle:
+            description: |
+              Phandle pointing to a rsense object associated with this
+              thermistor.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 250

Quoted 10 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +10 -0
+            $ref: "/schemas/types.yaml#/definitions/phandle"
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look at table 52
+              of the datasheet for how to set this value for thermistors.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 0
+              - maximum: 4

Nasty as value 3 is reserved. So break this one up into it's parts as well.

Quoted 168 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +156 -0
+
+          adi,excitation-current-nanoamp:
+            description: |
+              This property controls the magnitude of the excitation current
+              applied to the thermistor. Value 0 set's the sensor in auto-range
+              mode.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [0, 250, 500, 1000, 5000, 10000, 25000, 50000, 100000,
+                       250000, 500000, 1000000]
+
+          adi,custom-sensor:
+            description: |
+              This is a table, where each entry should be a pair of
+              resistance(ohm)-temperature(K). The entries added here are in uohm
+              and uK only for custom thermistors. For more details look at table
+              78 and 79. Steinhart-Hart coefficients are also supported and can
+              be programmed into the device memory using this property. For
+              Steinhart sensors, this table has a constant size of 6 entries
+              (defining the coefficients) and the values are given in the raw
+              format. Look at table 82 for more information.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64-array
+              - minItems: 6
+              - maxItems: 128
+
+        required:
+          - adi,sensor-type
+          - adi,rsense-handle
+
+      "^adc@.*":
+        type: object
+        description: Represents a channel which is being used as a direct adc.
+
+        properties:
+          adi,sensor-type:
+            description: Identifies the sensor as a direct adc.
+            const: 30
+
+          adi,single-ended:
+            description: Boolean property which set's the adc as single-ended.
+            type: boolean
+
+        required:
+          - adi,sensor-type
+
+      "^rsense@.*":
+        type: object
+        description: |
+          Represents a rsense which is connected to one of the device channels.
+          Rsense are used by thermistors and RTD's.
+
+        properties:
+          reg:
+            minimum: 2
+
+          adi,sensor-type:
+            description: Identifies the sensor as a rsense.
+            const: 29
+
+          adi,rsense-val-micro-ohms:
+            description: |
+              Sets the value of the sense resistor. Look at table 20 of the
+              datasheet for information.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64
+
+        required:
+          - adi,sensor-type
+          - adi, rsense-val
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spi0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        sensor_ltc2983: ltc2983@0 {
+                compatible = "adi,ltc2983";
+                reg = <0>;
+
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                adi,temperature-celcius;
+                interrupts = <20 IRQ_TYPE_EDGE_RISING>;
+                interrupt-parent = <&gpio>;
+
+                thermocouple@18 {
+                        reg = <18>;
+                        adi,sensor-type = <8>; //Type B
+                        adi,sensor-config = <1>; //Differential, open-circuit current
+                        adi,cold-junction-handle = <&diode5>;
+                };
+
+                diode5: diode@5 {
+                        reg = <5>;
+                        adi,sensor-type = <28>;
+                };
+
+                rsense2: rsense@2 {
+                        reg = <2>;
+                        adi,sensor-type = <29>;
+                        adi,rsense-val-micro-ohms = /bits/ 64 <1200000000>; //1.2Kohms
+                };
+
+                rtd@14 {
+                        reg = <14>;
+                        adi,sensor-type = <15>; //PT1000
+                        /*2-wire, internal gnd, no current rotation*/
+                        adi,sensor-config = <1>;
+                        adi,excitation-current = <7>; //500uA
+                        adi,rsense-handle = <&rsense2>;
+                };
+
+                adc@10 {
+                        reg = <10>;
+                        adi,sensor-type = <30>;
+                        adi,single-ended;
+                };
+
+                thermistor@12 {
+                        reg = <12>;
+                        adi,sensor-type = <26>; //Steinhart
+                        adi,rsense-handle = <&rsense2>;
+                        adi,custom-sensor = /bits/ 64 <0x00F371EC 0x12345678
+                                        0x2C0F8733 0x10018C66 0xA0FEACCD
+                                        0x90021D99>; //6 entries
+                };
+
+                thermocouple@20 {
+                        reg = <20>;
+                        adi,sensor-type = <9>; //custom thermocouple
+                        adi,sensor-config = <8>; //single-ended
+                        adi,custom-sensor = /bits/ 64
+                                 <(-50220000) 0
+                                  (-30200000) 99100000
+                                  (-5300000) 135400000
+                                  0 273150000
+                                  40200000 361200000
+                                  55300000 522100000
+                                  88300000 720300000
+                                  132200000 811200000
+                                  188700000 922500000
+                                  460400000 1000000000>; //10 pairs
+               };
+
+        };
+    };
+...
MAINTAINERS +1 -0
index 14a256e785ca..f747a9dc27f5 100644
@@ -9497,6 +9497,7 @@ W:	http://ez.analog.com/community/linux-device-drivers
 L:	[email protected]
 S:	Supported
 F:	drivers/iio/temperature/ltc2983.c
+F:	Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml
 
 LTC4261 HARDWARE MONITOR DRIVER
 M:	Guenter Roeck <[email protected]>
author maintainer
#3 lore raw

Re: [RESEND PATCH v2 2/2] dt-bindings: iio: Add ltc2983 documentation

Quoted 109 lines · Jonathan Cameron
Quoted 3 lines · On Mon, 30 Sep 2019 12:42:47 +0200 Nuno Sá <[email protected]> wrote:

Document the LTC2983 temperature sensor devicetree bindings.

Hi Nuno,

A few comments inline. This is a complex one so I'll definitely be looking for a review from Rob or Mark,

Thanks,

Jonathan

Quoted 92 lines

---
Changes in v2:
* Drop maxItems in non-array elements;
* Set adi,mux-delay-config-us instead of adi,mux-delay-config;
* Wrapped lines at 80 char;
* Added comas to enum elements;
* Use real units in adi,excitation-current;
* Moved some enums to minimum and maximum;
* Grouped patternProperties and moved reg property as a generic
property.

 .../bindings/iio/temperature/adi,ltc2983.yaml | 406
++++++++++++++++++
 MAINTAINERS                                   |   1 +
 2 files changed, 407 insertions(+)
 create mode 100644

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml

diff --git a/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yam l b/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yam l
new file mode 100644
index 000000000000..df68b8233e5e
--- /dev/null
+++
b/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yam l

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
@@ -0,0 +1,406 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: 

http://devicetree.org/schemas/iio/temperature/adi,ltc2983.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +8 -0
+
+title: Analog Devices LTC2983 Multi-sensor Temperature system
+
+maintainers:
+  - Nuno Sá <[email protected]>
+
+description: |
+  Analog Devices LTC2983 Multi-Sensor Digital Temperature

Measurement System
+
https://www.analog.com/media/en/technical-documentation/data-sheets/2983fc.pdf

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +15 -0
+
+properties:
+  compatible:
+    enum:
+      - adi,ltc2983
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  adi,temperature-celcius:
+    description:
+      If this property is present, the temperature is reported in

Celsius.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +5 -0
+    type: boolean
+
+  adi,mux-delay-config-us:
+    description:
+      The LTC2983 performs 2 or 3 internal conversion cycles per

temperature
+ result. Each conversion cycle is performed with different
excitation and
+ input multiplexer configurations. Prior to each conversion,
these
+ excitation circuits and input switch configurations are
changed and an
+ internal 1ms delay ensures settling prior to the conversion
cycle in most
+ cases. An extra delay can be configured using this property.
The value is

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +8 -0
+      rounded to nearest 100us.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - maximum: 255
+
+  adi,filter-notch-freq:
+    description:
+      Set's the default setting of the digital filter. The default

is

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+      simultaneous 50/60Hz rejection.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
Quoted 8 lines
Quoted 1 line

+ - maximum: 2

This one is an oddity and you should define what the 3 values mean. If the sensor had supported no notch rejection at all rather than just
50, 60, 50/60 I would have suggested two bools but as it stands I guess
this will just need to be an enum.

Yes, I guess we need the enum or like it is right know. I will add meaning to the values.

Quoted 34 lines
Quoted 34 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +15 -0
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+patternProperties:
+  ".*@([1-9]|1[0-9]|20)$":
+    type: object
+
+    properties:
+      reg:
+        description: |
+          The channel number. It can be connected to one of the 20

channels of

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +12 -0
+          the device.
+        minimum: 1
+        maximum: 20
+
+    required:
+      - reg
+
+    patternProperties:
+      "^thermocouple@.*":
+        type: object
+        description: |
+          Represents a thermocouple sensor which is connected to

one of the device

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +5 -0
+          channels.
+
+        properties:
+          adi,sensor-type:
+            description: |
Quoted 8 lines

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 89

Quoted 6 lines

+ Identifies the type of thermocouple connected to the
device.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 1
+              - maximum: 8

Meaning of values should be defined...

ack.

Quoted 11 lines

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 98

Quoted 11 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look

at table 14
+ of the datasheet for how to set this value for
thermocouples.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 1
+              - maximun: 15
Quoted 5 lines

Hmm. Whilst there are quite a few things in here, it would be nice to break it up
into human readable elements. It's only 3 things and there are a bunch of don't
care states it seems.

Yes, now that I gave it more thought, I see I was lazy here. I will replace this property with 2 other properties. A boolean for single- Ended and another uint32 prop for open-circuit-current. With those 2 properties I can set the sensor-config bits.

Quoted 40 lines
Quoted 40 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+
+          adi,cold-junction-handle:
+            description: |
+              Phandle which points to a sensor object responsible

for measuring

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +6 -0
+              the thermocouple cold junction temperature.
+            $ref: "/schemas/types.yaml#/definitions/phandle"
+
+          adi,custom-sensor:
+            description: |
+              This is a table, where each entry should be a pair

of
+ voltage(mv)-temperature(K). The entries must be
given in nv and uK
+ so that, the original values must be multiplied by
1000000. For

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +13 -0
+              more details look at table 69 and 70.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/int64-array
+              - minItems: 6
+              - maxItems: 128
+
+        required:
+          - adi,sensor-type
+
+      "^diode@.*":
+        type: object
+        description: |
+          Represents a diode sensor which is connected to one of

the device

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +10 -0
+          channels.
+
+        properties:
+          adi,sensor-type:
+            description: Identifies the sensor as a diode.
+            const: 28
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look
Quoted 8 lines

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 138

Quoted 7 lines

at table 17
+ of the datasheet for how to set this value for
diodes.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 0
+              - maximum: 7

Another one I'd like to see broken up.

ack. I can use 3 booleans here.

Quoted 57 lines
Quoted 57 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+
+          adi,excitation-current-microamp:
+            description: |
+              This property controls the magnitude of the

excitation current
+ applied to the diode. Depending on the number of
conversions
+ cycles, this property will assume different
predefined values on
+ each cycle. Just set the value of the first cycle
(1l).

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +7 -0
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [10, 20, 40, 80]
+
+          adi,ideal-factor-value:
+            description: |
+              This property sets the diode ideality factor. The

real value must
+ be multiplied by 1000000 to remove the fractional
part. For more

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +11 -0
+              information look at table 20 of the datasheet.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+
+        required:
+          - adi,sensor-type
+
+      "^rtd@.*":
+        type: object
+        description: |
+          Represents a rtd sensor which is connected to one of the

device channels.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +7 -0
+
+        properties:
+          reg:
+            minimum: 2
+
+          adi,sensor-type:
+            description: Identifies the type of RTD connected to

the device.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +8 -0
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 10
+              - maximum: 17
+
+          adi,rsense-handle:
+            description: |
+              Phandle pointing to a rsense object associated with

this RTD.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +5 -0
+            $ref: "/schemas/types.yaml#/definitions/phandle"
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look

at table 28
+ of the datasheet for how to set this value for

Quoted 8 lines

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 188

Quoted 4 lines

RTD's.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +3 -0
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [0, 1, 4, 5, 8, 9, 10, 12, 13, 14]

Another one to break up into it's parts, which would also get rid of the
enum with gaps element.

Will do that.

Quoted 68 lines
Quoted 68 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+
+          adi,excitation-current-microamp:
+            description: |
+              This property controls the magnitude of the

excitation current

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +8 -0
+              applied to the RTD.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [5, 10, 25, 50, 100, 250, 500, 1000]
+
+          adi,rtd-curve:
+            description: |
+              This property set the RTD curve used and the

corresponding
+ Callendar-VanDusen constants. Look at table 30 of
the datasheet.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +8 -0
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 0
+              - maximum: 3
+
+          adi,custom-sensor:
+            description: |
+              This is a table, where each entry should be a pair

of
+ resistance(ohm)-temperature(K). The entries added
here are in uohm
+ and uK. For more details values look at table 74 and
75.

(quoted diff) +2 -0
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64-

array

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +11 -0
+              - minItems: 6
+              - maxItems: 128
+
+        required:
+          - adi,sensor-type
+          - adi,rsense-handle
+
+      "^thermistor@.*":
+        type: object
+        description: |
+          Represents a thermistor sensor which is connected to one

of the device

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +15 -0
+          channels.
+
+        properties:
+          adi,sensor-type:
+            description: |
+              Identifies the type of thermistor connected to the
+              device.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 19
+              - maximum: 25
+
+          adi,rsense-handle:
+            description: |
+              Phandle pointing to a rsense object associated with

this

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +6 -0
+              thermistor.
+            $ref: "/schemas/types.yaml#/definitions/phandle"
+
+          adi,sensor-config:
+            description: |
+              Raw value which set's the sensor configuration. Look

at table 52

Quoted 8 lines

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml line 250

Quoted 6 lines

+ of the datasheet for how to set this value for
thermistors.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - minimum: 0
+              - maximum: 4

Nasty as value 3 is reserved. So break this one up into it's parts as well.

Arghh, that is obviously a problem. Will do that.

Quoted 192 lines
Quoted 192 lines
Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+
+          adi,excitation-current-nanoamp:
+            description: |
+              This property controls the magnitude of the

excitation current
+ applied to the thermistor. Value 0 set's the sensor
in auto-range

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +4 -0
+              mode.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [0, 250, 500, 1000, 5000, 10000, 25000,

50000, 100000,

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +5 -0
+                       250000, 500000, 1000000]
+
+          adi,custom-sensor:
+            description: |
+              This is a table, where each entry should be a pair

of
+ resistance(ohm)-temperature(K). The entries added
here are in uohm
+ and uK only for custom thermistors. For more details
look at table
+ 78 and 79. Steinhart-Hart coefficients are also
supported and can
+ be programmed into the device memory using this
property. For
+ Steinhart sensors, this table has a constant size of
6 entries
+ (defining the coefficients) and the values are given
in the raw

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +3 -0
+              format. Look at table 82 for more information.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64-

array

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +10 -0
+              - minItems: 6
+              - maxItems: 128
+
+        required:
+          - adi,sensor-type
+          - adi,rsense-handle
+
+      "^adc@.*":
+        type: object
+        description: Represents a channel which is being used as a

direct adc.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +8 -0
+
+        properties:
+          adi,sensor-type:
+            description: Identifies the sensor as a direct adc.
+            const: 30
+
+          adi,single-ended:
+            description: Boolean property which set's the adc as

single-ended.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +9 -0
+            type: boolean
+
+        required:
+          - adi,sensor-type
+
+      "^rsense@.*":
+        type: object
+        description: |
+          Represents a rsense which is connected to one of the

device channels.

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +13 -0
+          Rsense are used by thermistors and RTD's.
+
+        properties:
+          reg:
+            minimum: 2
+
+          adi,sensor-type:
+            description: Identifies the sensor as a rsense.
+            const: 29
+
+          adi,rsense-val-micro-ohms:
+            description: |
+              Sets the value of the sense resistor. Look at table

20 of the

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +35 -0
+              datasheet for information.
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint64
+
+        required:
+          - adi,sensor-type
+          - adi, rsense-val
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spi0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        sensor_ltc2983: ltc2983@0 {
+                compatible = "adi,ltc2983";
+                reg = <0>;
+
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                adi,temperature-celcius;
+                interrupts = <20 IRQ_TYPE_EDGE_RISING>;
+                interrupt-parent = <&gpio>;
+
+                thermocouple@18 {
+                        reg = <18>;
+                        adi,sensor-type = <8>; //Type B
+                        adi,sensor-config = <1>; //Differential,

open-circuit current

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +12 -0
+                        adi,cold-junction-handle = <&diode5>;
+                };
+
+                diode5: diode@5 {
+                        reg = <5>;
+                        adi,sensor-type = <28>;
+                };
+
+                rsense2: rsense@2 {
+                        reg = <2>;
+                        adi,sensor-type = <29>;
+                        adi,rsense-val-micro-ohms = /bits/ 64

<1200000000>; //1.2Kohms

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +6 -0
+                };
+
+                rtd@14 {
+                        reg = <14>;
+                        adi,sensor-type = <15>; //PT1000
+                        /*2-wire, internal gnd, no current

rotation*/

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +16 -0
+                        adi,sensor-config = <1>;
+                        adi,excitation-current = <7>; //500uA
+                        adi,rsense-handle = <&rsense2>;
+                };
+
+                adc@10 {
+                        reg = <10>;
+                        adi,sensor-type = <30>;
+                        adi,single-ended;
+                };
+
+                thermistor@12 {
+                        reg = <12>;
+                        adi,sensor-type = <26>; //Steinhart
+                        adi,rsense-handle = <&rsense2>;
+                        adi,custom-sensor = /bits/ 64 <0x00F371EC

0x12345678
+ 0x2C0F8733 0x10018C66
0xA0FEACCD

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +6 -0
+                                        0x90021D99>; //6 entries
+                };
+
+                thermocouple@20 {
+                        reg = <20>;
+                        adi,sensor-type = <9>; //custom

thermocouple

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +12 -0
+                        adi,sensor-config = <8>; //single-ended
+                        adi,custom-sensor = /bits/ 64
+                                 <(-50220000) 0
+                                  (-30200000) 99100000
+                                  (-5300000) 135400000
+                                  0 273150000
+                                  40200000 361200000
+                                  55300000 522100000
+                                  88300000 720300000
+                                  132200000 811200000
+                                  188700000 922500000
+                                  460400000 1000000000>; //10

pairs

Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file +5 -0
+               };
+
+        };
+    };
+...
MAINTAINERS +0 -0
index 14a256e785ca..f747a9dc27f5 100644
@@ -9497,6 +9497,7 @@ W:	

http://ez.analog.com/community/linux-device-drivers
L: [email protected]
S: Supported
F: drivers/iio/temperature/ltc2983.c
+F: Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.y
aml

LTC4261 HARDWARE MONITOR DRIVER
M: Guenter Roeck <[email protected]>

maintainer
#4 lore raw
In reply to Nuno Sá
Quoted 8 lines · On Mon, 30 Sep 2019 12:42:46 +0200 Nuno Sá <[email protected]> wrote:

The LTC2983 is a Multi-Sensor High Accuracy Digital Temperature Measurement System. It measures a wide variety of temperature sensors and digitally outputs the result, in °C or °F, with 0.1°C accuracy and 0.001°C resolution. It can measure the temperature of all standard thermocouples (type B,E,J,K,N,S,R,T), standard 2-,3-,4-wire RTDs, thermistors and diodes.

One minor comment inline. I don't see a reason to use a threaded irq to simply set a completion. Just do it with a traditional irq. I suspect the overhead of doing that is probably similar to spinning up the irq thread.

Otherwise, I'm happy with this subject to binding review.

Thanks,

Jonathan

Quoted 1,181 lines

---
Changes in v2:
* Added some needed blank lines (for readability);
* Allocate iio_chan in the setup() function;
* Rename reset to sleep;
* Remove unneeded dev_dbg calls;
* Remove unneeded line wrapping;
* Remove unneeded comments;
* Remove extend_names. Use the standard ABI;
* Adapt the scales to report in millivolt and milli degrees;
* Adapt the of_property readings to the renaming of the properties;
* For custom thermistors, excitation-current cannot be set to Auto range.

 MAINTAINERS                       |    7 +
 drivers/iio/temperature/Kconfig   |   10 +
 drivers/iio/temperature/Makefile  |    1 +
 drivers/iio/temperature/ltc2983.c | 1436 +++++++++++++++++++++++++++++
 4 files changed, 1454 insertions(+)
 create mode 100644 drivers/iio/temperature/ltc2983.c
MAINTAINERS +7 -0
index f0c03740b9fb..14a256e785ca 100644
@@ -9491,6 +9491,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/iio/dac/ltc1660.txt
 F:	drivers/iio/dac/ltc1660.c
 
+LTC2983 IIO TEMPERATURE DRIVER
+M:	Nuno Sá <[email protected]>
+W:	http://ez.analog.com/community/linux-device-drivers
+L:	[email protected]
+S:	Supported
+F:	drivers/iio/temperature/ltc2983.c
+
 LTC4261 HARDWARE MONITOR DRIVER
 M:	Guenter Roeck <[email protected]>
 L:	[email protected]
drivers/iio/temperature/Kconfig +10 -0
index 737faa0901fe..04b5a67b593c 100644
@@ -4,6 +4,16 @@
 #
 menu "Temperature sensors"
 
+config LTC2983
+	tristate "Analog Devices Multi-Sensor Digital Temperature Measurement System"
+	depends on SPI
+	help
+	  Say yes here to build support for the LTC2983 Multi-Sensor
+	  high accuracy digital temperature measurement system.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called ltc2983.
+
 config MAXIM_THERMOCOUPLE
 	tristate "Maxim thermocouple sensors"
 	depends on SPI
drivers/iio/temperature/Makefile +1 -0
index baca4776ca0d..d6b850b0cf63 100644
@@ -3,6 +3,7 @@
 # Makefile for industrial I/O temperature drivers
 #
 
+obj-$(CONFIG_LTC2983) += ltc2983.o
 obj-$(CONFIG_HID_SENSOR_TEMP) += hid-sensor-temperature.o
 obj-$(CONFIG_MAXIM_THERMOCOUPLE) += maxim_thermocouple.o
 obj-$(CONFIG_MAX31856) += max31856.o
drivers/iio/temperature/ltc2983.c new file +1104 -0
new file mode 100644
index 000000000000..7c159da9f183
@@ -0,0 +1,1436 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Analog Devices LTC2983 Multi-Sensor Digital Temperature Measurement System
+ * driver
+ *
+ * Copyright 2019 Analog Devices Inc.
+ */
+#include <linux/bitfield.h>
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/iio/iio.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+/* register map */
+#define LTC2983_STATUS_REG			0x0000
+#define LTC2983_TEMP_RES_START_REG		0x0010
+#define LTC2983_TEMP_RES_END_REG		0x005F
+#define LTC2983_GLOBAL_CONFIG_REG		0x00F0
+#define LTC2983_MULT_CHANNEL_START_REG		0x00F4
+#define LTC2983_MULT_CHANNEL_END_REG		0x00F7
+#define LTC2983_MUX_CONFIG_REG			0x00FF
+#define LTC2983_CHAN_ASSIGN_START_REG		0x0200
+#define LTC2983_CHAN_ASSIGN_END_REG		0x024F
+#define LTC2983_CUST_SENS_TBL_START_REG		0x0250
+#define LTC2983_CUST_SENS_TBL_END_REG		0x03CF
+
+#define LTC2983_DIFFERENTIAL_CHAN_MIN		2
+#define LTC2983_MAX_CHANNELS_NR			20
+#define LTC2983_MIN_CHANNELS_NR			1
+#define LTC2983_SLEEP				0x97
+#define LTC2983_CUSTOM_STEINHART_SIZE		24
+#define LTC2983_CUSTOM_SENSOR_ENTRY_SZ		6
+#define LTC2983_CUSTOM_STEINHART_ENTRY_SZ	4
+
+#define LTC2983_CHAN_START_ADDR(chan) \
+			(((chan - 1) * 4) + LTC2983_CHAN_ASSIGN_START_REG)
+#define LTC2983_CHAN_RES_ADDR(chan) \
+			(((chan - 1) * 4) + LTC2983_TEMP_RES_START_REG)
+#define LTC2983_THERMOCOUPLE_DIFF_MASK		BIT(3)
+#define LTC2983_THERMISTOR_DIFF_MASK		BIT(2)
+#define LTC2983_DIODE_DIFF_MASK			BIT(2)
+#define LTC2983_RTD_4_WIRE_MASK			BIT(3)
+#define LTC2983_RTD_ROTATION_MASK		BIT(1)
+#define LTC2983_RTD_KELVIN_R_SENSE_MASK		GENMASK(3, 2)
+
+#define LTC2983_COMMON_HARD_FAULT_MASK	GENMASK(31, 30)
+#define LTC2983_COMMON_SOFT_FAULT_MASK	GENMASK(27, 25)
+
+#define	LTC2983_STATUS_START_MASK	BIT(7)
+#define	LTC2983_STATUS_START(x)		FIELD_PREP(LTC2983_STATUS_START_MASK, x)
+
+#define	LTC2983_STATUS_CHAN_SEL_MASK	GENMASK(4, 0)
+#define	LTC2983_STATUS_CHAN_SEL(x) \
+				FIELD_PREP(LTC2983_STATUS_CHAN_SEL_MASK, x)
+
+#define LTC2983_TEMP_UNITS_MASK		BIT(2)
+#define LTC2983_TEMP_UNITS(x)		FIELD_PREP(LTC2983_TEMP_UNITS_MASK, x)
+
+#define LTC2983_NOTCH_FREQ_MASK		GENMASK(1, 0)
+#define LTC2983_NOTCH_FREQ(x)		FIELD_PREP(LTC2983_NOTCH_FREQ_MASK, x)
+
+#define LTC2983_RES_VALID_MASK		BIT(24)
+#define LTC2983_DATA_MASK		GENMASK(23, 0)
+#define LTC2983_DATA_SIGN_BIT		23
+
+#define LTC2983_CHAN_TYPE_MASK		GENMASK(31, 27)
+#define LTC2983_CHAN_TYPE(x)		FIELD_PREP(LTC2983_CHAN_TYPE_MASK, x)
+
+/* cold junction for thermocouples and rsense for rtd's and thermistor's */
+#define LTC2983_CHAN_ASSIGN_MASK	GENMASK(26, 22)
+#define LTC2983_CHAN_ASSIGN(x)		FIELD_PREP(LTC2983_CHAN_ASSIGN_MASK, x)
+
+#define LTC2983_CUSTOM_LEN_MASK		GENMASK(5, 0)
+#define LTC2983_CUSTOM_LEN(x)		FIELD_PREP(LTC2983_CUSTOM_LEN_MASK, x)
+
+#define LTC2983_CUSTOM_ADDR_MASK	GENMASK(11, 6)
+#define LTC2983_CUSTOM_ADDR(x)		FIELD_PREP(LTC2983_CUSTOM_ADDR_MASK, x)
+
+#define LTC2983_THERMOCOUPLE_CFG_MASK	GENMASK(21, 18)
+#define LTC2983_THERMOCOUPLE_CFG(x) \
+				FIELD_PREP(LTC2983_THERMOCOUPLE_CFG_MASK, x)
+#define LTC2983_THERMOCOUPLE_HARD_FAULT_MASK	GENMASK(31, 29)
+#define LTC2983_THERMOCOUPLE_SOFT_FAULT_MASK	GENMASK(28, 25)
+
+#define LTC2983_RTD_CFG_MASK		GENMASK(21, 18)
+#define LTC2983_RTD_CFG(x)		FIELD_PREP(LTC2983_RTD_CFG_MASK, x)
+#define LTC2983_RTD_EXC_CURRENT_MASK	GENMASK(17, 14)
+#define LTC2983_RTD_EXC_CURRENT(x) \
+				FIELD_PREP(LTC2983_RTD_EXC_CURRENT_MASK, x)
+#define LTC2983_RTD_CURVE_MASK		GENMASK(13, 12)
+#define LTC2983_RTD_CURVE(x)		FIELD_PREP(LTC2983_RTD_CURVE_MASK, x)
+
+#define LTC2983_THERMISTOR_CFG_MASK	GENMASK(21, 19)
+#define LTC2983_THERMISTOR_CFG(x) \
+				FIELD_PREP(LTC2983_THERMISTOR_CFG_MASK, x)
+#define LTC2983_THERMISTOR_EXC_CURRENT_MASK	GENMASK(18, 15)
+#define LTC2983_THERMISTOR_EXC_CURRENT(x) \
+			FIELD_PREP(LTC2983_THERMISTOR_EXC_CURRENT_MASK, x)
+
+#define LTC2983_DIODE_CFG_MASK		GENMASK(26, 24)
+#define LTC2983_DIODE_CFG(x)		FIELD_PREP(LTC2983_DIODE_CFG_MASK, x)
+#define LTC2983_DIODE_EXC_CURRENT_MASK	GENMASK(23, 22)
+#define LTC2983_DIODE_EXC_CURRENT(x) \
+				FIELD_PREP(LTC2983_DIODE_EXC_CURRENT_MASK, x)
+#define LTC2983_DIODE_IDEAL_FACTOR_MASK	GENMASK(21, 0)
+#define LTC2983_DIODE_IDEAL_FACTOR(x) \
+				FIELD_PREP(LTC2983_DIODE_IDEAL_FACTOR_MASK, x)
+
+#define LTC2983_R_SENSE_VAL_MASK	GENMASK(26, 0)
+#define LTC2983_R_SENSE_VAL(x)		FIELD_PREP(LTC2983_R_SENSE_VAL_MASK, x)
+
+#define LTC2983_ADC_SINGLE_ENDED_MASK	BIT(26)
+#define LTC2983_ADC_SINGLE_ENDED(x) \
+				FIELD_PREP(LTC2983_ADC_SINGLE_ENDED_MASK, x)
+
+enum {
+	LTC2983_SENSOR_THERMOCOUPLE = 1,
+	LTC2983_SENSOR_THERMOCOUPLE_CUSTOM = 9,
+	LTC2983_SENSOR_RTD = 10,
+	LTC2983_SENSOR_RTD_CUSTOM = 18,
+	LTC2983_SENSOR_THERMISTOR = 19,
+	LTC2983_SENSOR_THERMISTOR_STEINHART = 26,
+	LTC2983_SENSOR_THERMISTOR_CUSTOM = 27,
+	LTC2983_SENSOR_DIODE = 28,
+	LTC2983_SENSOR_SENSE_RESISTOR = 29,
+	LTC2983_SENSOR_DIRECT_ADC = 30,
+};
+
+#define to_thermocouple(_sensor) \
+		container_of(_sensor, struct ltc2983_thermocouple, sensor)
+
+#define to_rtd(_sensor) \
+		container_of(_sensor, struct ltc2983_rtd, sensor)
+
+#define to_thermistor(_sensor) \
+		container_of(_sensor, struct ltc2983_thermistor, sensor)
+
+#define to_diode(_sensor) \
+		container_of(_sensor, struct ltc2983_diode, sensor)
+
+#define to_rsense(_sensor) \
+		container_of(_sensor, struct ltc2983_rsense, sensor)
+
+#define to_adc(_sensor) \
+		container_of(_sensor, struct ltc2983_adc, sensor)
+
+struct ltc2983_data {
+	struct regmap *regmap;
+	struct spi_device *spi;
+	struct mutex lock;
+	struct completion completion;
+	struct iio_chan_spec *iio_chan;
+	struct ltc2983_sensor **sensors;
+	u32 mux_delay_config;
+	u32 filter_notch_freq;
+	u16 custom_table_size;
+	u8 num_channels;
+	u8 iio_channels;
+	bool temp_farenheit;
+	bool sleep;
+};
+
+struct ltc2983_sensor {
+	int (*fault_handler)(const struct ltc2983_data *st, const u32 result);
+	int (*assign_chan)(struct ltc2983_data *st,
+			   const struct ltc2983_sensor *sensor);
+	/* specifies the sensor channel */
+	u32 chan;
+	/* sensor type */
+	u32 type;
+};
+
+struct ltc2983_custom_sensor {
+	/* raw table sensor data */
+	u8 *table;
+	size_t size;
+	/* address offset */
+	s8 offset;
+	bool is_steinhart;
+};
+
+struct ltc2983_thermocouple {
+	struct ltc2983_sensor sensor;
+	struct ltc2983_custom_sensor *custom;
+	u32 sensor_config;
+	u32 cold_junction_chan;
+};
+
+struct ltc2983_rtd {
+	struct ltc2983_sensor sensor;
+	struct ltc2983_custom_sensor *custom;
+	u32 sensor_config;
+	u32 r_sense_chan;
+	u32 excitation_current;
+	u32 rtd_curve;
+};
+
+struct ltc2983_thermistor {
+	struct ltc2983_sensor sensor;
+	struct ltc2983_custom_sensor *custom;
+	u32 sensor_config;
+	u32 r_sense_chan;
+	u32 excitation_current;
+};
+
+struct ltc2983_diode {
+	struct ltc2983_sensor sensor;
+	u32 sensor_config;
+	u32 excitation_current;
+	u32 ideal_factor_value;
+};
+
+struct ltc2983_rsense {
+	struct ltc2983_sensor sensor;
+	u32 r_sense_val;
+};
+
+struct ltc2983_adc {
+	struct ltc2983_sensor sensor;
+	bool single_ended;
+};
+
+/*
+ * Convert to Q format numbers. These number's are integers where
+ * the number of integer and fractional bits are specified. The resolution
+ * is given by 1/@resolution and tell us the number of fractional bits. For
+ * instance a resolution of 2^-10 means we have 10 fractional bits.
+ */
+static u32 __convert_to_raw(const u64 val, const u32 resolution)
+{
+	u64 __res = val * resolution;
+
+	/* all values are multiplied by 1000000 to remove the fraction */
+	do_div(__res, 1000000);
+
+	return __res;
+}
+
+static u32 __convert_to_raw_sign(const u64 val, const u32 resolution)
+{
+	s64 __res = -(s32)val;
+
+	__res = __convert_to_raw(__res, resolution);
+
+	return (u32)-__res;
+}
+
+static int __ltc2983_fault_handler(const struct ltc2983_data *st,
+				   const u32 result, const u32 hard_mask,
+				   const u32 soft_mask)
+{
+	const struct device *dev = &st->spi->dev;
+
+	if (result & hard_mask) {
+		dev_err(dev, "Invalid conversion: Sensor HARD fault\n");
+		return -EIO;
+	} else if (result & soft_mask) {
+		/* just print a warning */
+		dev_warn(dev, "Suspicious conversion: Sensor SOFT fault\n");
+	}
+
+	return 0;
+}
+
+static int __ltc2983_chan_assign_common(const struct ltc2983_data *st,
+					const struct ltc2983_sensor *sensor,
+					u32 chan_val)
+{
+	u32 reg = LTC2983_CHAN_START_ADDR(sensor->chan);
+	__be32 __chan_val;
+
+	chan_val |= LTC2983_CHAN_TYPE(sensor->type);
+	dev_dbg(&st->spi->dev, "Assign reg:0x%04X, val:0x%08X\n", reg,
+								chan_val);
+	__chan_val = cpu_to_be32(chan_val);
+	return regmap_bulk_write(st->regmap, reg, &__chan_val,
+				 sizeof(__chan_val));
+}
+
+static int __ltc2983_chan_custom_sensor_assign(struct ltc2983_data *st,
+					  struct ltc2983_custom_sensor *custom,
+					  u32 *chan_val)
+{
+	u32 reg;
+	u8 mult = custom->is_steinhart ? LTC2983_CUSTOM_STEINHART_ENTRY_SZ :
+		LTC2983_CUSTOM_SENSOR_ENTRY_SZ;
+	const struct device *dev = &st->spi->dev;
+	/*
+	 * custom->size holds the raw size of the table. However, when
+	 * configuring the sensor channel, we must write the number of
+	 * entries of the table minus 1. For steinhart sensors 0 is written
+	 * since the size is constant!
+	 */
+	const u8 len = custom->is_steinhart ? 0 :
+		(custom->size / LTC2983_CUSTOM_SENSOR_ENTRY_SZ) - 1;
+	/*
+	 * Check if the offset was assigned already. It should be for steinhart
+	 * sensors. When coming from sleep, it should be assigned for all.
+	 */
+	if (custom->offset < 0) {
+		/*
+		 * This needs to be done again here because, from the moment
+		 * when this test was done (successfully) for this custom
+		 * sensor, a steinhart sensor might have been added changing
+		 * custom_table_size...
+		 */
+		if (st->custom_table_size + custom->size >
+		    (LTC2983_CUST_SENS_TBL_END_REG -
+		     LTC2983_CUST_SENS_TBL_START_REG) + 1) {
+			dev_err(dev,
+				"Not space left(%d) for new custom sensor(%zu)",
+							st->custom_table_size,
+							custom->size);
+			return -EINVAL;
+		}
+
+		custom->offset = st->custom_table_size /
+					LTC2983_CUSTOM_SENSOR_ENTRY_SZ;
+		st->custom_table_size += custom->size;
+	}
+
+	reg = (custom->offset * mult) + LTC2983_CUST_SENS_TBL_START_REG;
+
+	*chan_val |= LTC2983_CUSTOM_LEN(len);
+	*chan_val |= LTC2983_CUSTOM_ADDR(custom->offset);
+	dev_dbg(dev, "Assign custom sensor, reg:0x%04X, off:%d, sz:%zu",
+							reg, custom->offset,
+							custom->size);
+	/* write custom sensor table */
+	return regmap_bulk_write(st->regmap, reg, custom->table, custom->size);
+}
+
+static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new(
+						struct ltc2983_data *st,
+						const struct device_node *np,
+						const bool is_steinhart,
+						const u32 resolution,
+						const bool has_signed)
+{
+	struct ltc2983_custom_sensor *new_custom;
+	u8 index, n_entries, tbl = 0;
+	struct device *dev = &st->spi->dev;
+	/*
+	 * For custom steinhart, the full u32 is taken. For all the others
+	 * the MSB is discarded.
+	 */
+	const u8 n_size = (is_steinhart == true) ? 4 : 3;
+
+	n_entries = of_property_count_elems_of_size(np, "adi,custom-sensor",
+						sizeof(u64));
+	/* n_entries must be an even number */
+	if (!n_entries || (n_entries % 2) != 0) {
+		dev_err(dev, "Number of entries either 0 or not even\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	new_custom = devm_kzalloc(dev, sizeof(*new_custom), GFP_KERNEL);
+	if (!new_custom)
+		return ERR_PTR(-ENOMEM);
+
+	new_custom->size = n_entries * n_size;
+	/* check Steinhart size */
+	if (is_steinhart && new_custom->size != LTC2983_CUSTOM_STEINHART_SIZE) {
+		dev_err(dev, "Steinhart sensors size(%zu) must be 24",
+							new_custom->size);
+		return ERR_PTR(-EINVAL);
+	}
+	/* Check space on the table. */
+	if (st->custom_table_size + new_custom->size >
+	    (LTC2983_CUST_SENS_TBL_END_REG -
+	     LTC2983_CUST_SENS_TBL_START_REG) + 1) {
+		dev_err(dev, "No space left(%d) for new custom sensor(%zu)",
+				st->custom_table_size, new_custom->size);
+		return ERR_PTR(-EINVAL);
+	}
+
+	/* allocate the table */
+	new_custom->table = devm_kzalloc(dev, new_custom->size, GFP_KERNEL);
+	if (!new_custom->table)
+		return ERR_PTR(-ENOMEM);
+
+	for (index = 0; index < n_entries; index++) {
+		u64 temp = 0, j;
+
+		of_property_read_u64_index(np, "adi,custom-sensor", index,
+					   &temp);
+		/*
+		 * Steinhart sensors are configured with raw values in the
+		 * devicetree. For the other sensors we must convert the
+		 * value to raw. The odd index's correspond to temperarures
+		 * and always have 1/1024 of resolution. Temperatures also
+		 * come in kelvin, so signed values is not possible
+		 */
+		if (!is_steinhart) {
+			if ((index % 2) != 0)
+				temp = __convert_to_raw(temp, 1024);
+			else if (has_signed && (s64)temp < 0)
+				temp = __convert_to_raw_sign(temp, resolution);
+			else
+				temp = __convert_to_raw(temp, resolution);
+		}
+
+		for (j = 0; j < n_size; j++)
+			new_custom->table[tbl++] =
+				temp >> (8 * (n_size - j - 1));
+	}
+
+	new_custom->is_steinhart = is_steinhart;
+	/*
+	 * This is done to first add all the steinhart sensors to the table,
+	 * in order to maximize the table usage. If we mix adding steinhart
+	 * with the other sensors, we might have to do some roundup to make
+	 * sure that sensor_addr - 0x250(start address) is a multiple of 4
+	 * (for steinhart), and a multiple of 6 for all the other sensors.
+	 * Since we have const 24 bytes for steinhart sensors and 24 is
+	 * also a multiple of 6, we guarantee that the first non-steinhart
+	 * sensor will sit in a correct address without the need of filling
+	 * addresses.
+	 */
+	if (is_steinhart) {
+		new_custom->offset = st->custom_table_size /
+					LTC2983_CUSTOM_STEINHART_ENTRY_SZ;
+		st->custom_table_size += new_custom->size;
+	} else {
+		/* mark as unset. This is checked later on the assign phase */
+		new_custom->offset = -1;
+	}
+
+	return new_custom;
+}
+
+static int ltc2983_thermocouple_fault_handler(const struct ltc2983_data *st,
+					      const u32 result)
+{
+	return __ltc2983_fault_handler(st, result,
+				       LTC2983_THERMOCOUPLE_HARD_FAULT_MASK,
+				       LTC2983_THERMOCOUPLE_SOFT_FAULT_MASK);
+}
+
+static int ltc2983_common_fault_handler(const struct ltc2983_data *st,
+					const u32 result)
+{
+	return __ltc2983_fault_handler(st, result,
+				       LTC2983_COMMON_HARD_FAULT_MASK,
+				       LTC2983_COMMON_SOFT_FAULT_MASK);
+}
+
+static int ltc2983_thermocouple_assign_chan(struct ltc2983_data *st,
+				const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_thermocouple *thermo = to_thermocouple(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_CHAN_ASSIGN(thermo->cold_junction_chan);
+	chan_val |= LTC2983_THERMOCOUPLE_CFG(thermo->sensor_config);
+
+	if (thermo->custom) {
+		int ret;
+
+		ret = __ltc2983_chan_custom_sensor_assign(st, thermo->custom,
+							  &chan_val);
+		if (ret)
+			return ret;
+	}
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static int ltc2983_rtd_assign_chan(struct ltc2983_data *st,
+				   const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_rtd *rtd = to_rtd(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_CHAN_ASSIGN(rtd->r_sense_chan);
+	chan_val |= LTC2983_RTD_CFG(rtd->sensor_config);
+	chan_val |= LTC2983_RTD_EXC_CURRENT(rtd->excitation_current);
+	chan_val |= LTC2983_RTD_CURVE(rtd->rtd_curve);
+
+	if (rtd->custom) {
+		int ret;
+
+		ret = __ltc2983_chan_custom_sensor_assign(st, rtd->custom,
+							  &chan_val);
+		if (ret)
+			return ret;
+	}
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static int ltc2983_thermistor_assign_chan(struct ltc2983_data *st,
+					  const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_thermistor *thermistor = to_thermistor(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_CHAN_ASSIGN(thermistor->r_sense_chan);
+	chan_val |= LTC2983_THERMISTOR_CFG(thermistor->sensor_config);
+	chan_val |=
+		LTC2983_THERMISTOR_EXC_CURRENT(thermistor->excitation_current);
+
+	if (thermistor->custom) {
+		int ret;
+
+		ret = __ltc2983_chan_custom_sensor_assign(st,
+							  thermistor->custom,
+							  &chan_val);
+		if (ret)
+			return ret;
+	}
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static int ltc2983_diode_assign_chan(struct ltc2983_data *st,
+				     const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_diode *diode = to_diode(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_DIODE_CFG(diode->sensor_config);
+	chan_val |= LTC2983_DIODE_EXC_CURRENT(diode->excitation_current);
+	chan_val |= LTC2983_DIODE_IDEAL_FACTOR(diode->ideal_factor_value);
+
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static int ltc2983_r_sense_assign_chan(struct ltc2983_data *st,
+				       const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_rsense *rsense = to_rsense(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_R_SENSE_VAL(rsense->r_sense_val);
+
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static int ltc2983_adc_assign_chan(struct ltc2983_data *st,
+				   const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_adc *adc = to_adc(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_ADC_SINGLE_ENDED(adc->single_ended);
+
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static struct ltc2983_sensor *ltc2983_thermocouple_new(
+					const struct device_node *child,
+					struct ltc2983_data *st,
+					const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_thermocouple *thermo;
+	struct device_node *phandle;
+
+	thermo = devm_kzalloc(&st->spi->dev, sizeof(*thermo), GFP_KERNEL);
+	if (!thermo)
+		return ERR_PTR(-ENOMEM);
+
+	of_property_read_u32(child, "adi,sensor-config",
+				 &thermo->sensor_config);
+	/* validate channel index */
+	if (!(thermo->sensor_config & LTC2983_THERMOCOUPLE_DIFF_MASK) &&
+	    sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+		dev_err(&st->spi->dev,
+			"Invalid chann:%d for differential thermocouple",
+								sensor->chan);
+		return ERR_PTR(-EINVAL);
+	}
+
+	phandle = of_parse_phandle(child, "adi,cold-junction-handle", 0);
+	if (phandle) {
+		int ret;
+
+		ret = of_property_read_u32(phandle, "reg",
+					   &thermo->cold_junction_chan);
+		if (ret) {
+			/*
+			 * This would be catched later but we can just return
+			 * the error right away.
+			 */
+			dev_err(&st->spi->dev, "Property reg must be given\n");
+			of_node_put(phandle);
+			return ERR_PTR(-EINVAL);
+		}
+	}
+
+	/* check custom sensor */
+	if (sensor->type == LTC2983_SENSOR_THERMOCOUPLE_CUSTOM) {
+		thermo->custom = __ltc2983_custom_sensor_new(st, child, false,
+							     16384, true);
+		if (IS_ERR(thermo->custom)) {
+			of_node_put(phandle);
+			return ERR_CAST(thermo->custom);
+		}
+	}
+
+	/* set common parameters */
+	thermo->sensor.fault_handler = ltc2983_thermocouple_fault_handler;
+	thermo->sensor.assign_chan = ltc2983_thermocouple_assign_chan;
+
+	of_node_put(phandle);
+	return &thermo->sensor;
+}
+
+static struct ltc2983_sensor *ltc2983_rtd_new(const struct device_node *child,
+					  struct ltc2983_data *st,
+					  const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_rtd *rtd;
+	int ret = 0;
+	struct device *dev = &st->spi->dev;
+	struct device_node *phandle;
+	u32 excitation_current = 0;
+
+	rtd = devm_kzalloc(dev, sizeof(*rtd), GFP_KERNEL);
+	if (!rtd)
+		return ERR_PTR(-ENOMEM);
+
+	phandle = of_parse_phandle(child, "adi,rsense-handle", 0);
+	if (!phandle) {
+		dev_err(dev, "Property adi,rsense-handle missing or invalid");
+		return ERR_PTR(-EINVAL);
+	}
+
+	ret = of_property_read_u32(phandle, "reg", &rtd->r_sense_chan);
+	if (ret) {
+		dev_err(dev, "Property reg must be given\n");
+		goto fail;
+	}
+
+	of_property_read_u32(child, "adi,sensor-config", &rtd->sensor_config);
+	/*
+	 * rtd channel indexes are a bit more complicated to validate.
+	 * For 4wire RTD with rotation, the channel selection cannot be
+	 * >=19 since the chann + 1 is used in this configuration.
+	 * For 4wire RTDs with kelvin rsense, the rsense channel cannot be
+	 * <=1 since chanel - 1 and channel - 2 are used.
+	 */
+	if (rtd->sensor_config & LTC2983_RTD_4_WIRE_MASK) {
+		/* 4-wire */
+		u8 min = LTC2983_DIFFERENTIAL_CHAN_MIN,
+			max = LTC2983_MAX_CHANNELS_NR;
+
+		if (rtd->sensor_config & LTC2983_RTD_ROTATION_MASK)
+			max = LTC2983_MAX_CHANNELS_NR - 1;
+
+		if (((rtd->sensor_config & LTC2983_RTD_KELVIN_R_SENSE_MASK)
+		     == LTC2983_RTD_KELVIN_R_SENSE_MASK) &&
+		    (rtd->r_sense_chan <=  min)) {
+			/* kelvin rsense*/
+			dev_err(dev,
+				"Invalid rsense chann:%d to use in kelvin rsense",
+							rtd->r_sense_chan);
+
+			ret = -EINVAL;
+			goto fail;
+		}
+
+		if (sensor->chan < min || sensor->chan > max) {
+			dev_err(dev, "Invalid chann:%d for the rtd config",
+								sensor->chan);
+
+			ret = -EINVAL;
+			goto fail;
+		}
+	} else {
+		/* same as differential case */
+		if (sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+			dev_err(&st->spi->dev,
+				"Invalid chann:%d for RTD", sensor->chan);
+
+			ret = -EINVAL;
+			goto fail;
+		}
+	}
+
+	/* check custom sensor */
+	if (sensor->type == LTC2983_SENSOR_RTD_CUSTOM) {
+		rtd->custom = __ltc2983_custom_sensor_new(st, child, false,
+							  2048, false);
+		if (IS_ERR(rtd->custom)) {
+			of_node_put(phandle);
+			return ERR_CAST(rtd->custom);
+		}
+	}
+
+	/* set common parameters */
+	rtd->sensor.fault_handler = ltc2983_common_fault_handler;
+	rtd->sensor.assign_chan = ltc2983_rtd_assign_chan;
+
+	ret = of_property_read_u32(child, "adi,excitation-current-microamp",
+				   &excitation_current);
+	if (ret) {
+		/* default to 5uA */
+		rtd->excitation_current = 1;
+	} else {
+		switch (excitation_current) {
+		case 5:
+			rtd->excitation_current = 0x01;
+			break;
+		case 10:
+			rtd->excitation_current = 0x02;
+			break;
+		case 25:
+			rtd->excitation_current = 0x03;
+			break;
+		case 50:
+			rtd->excitation_current = 0x04;
+			break;
+		case 100:
+			rtd->excitation_current = 0x05;
+			break;
+		case 250:
+			rtd->excitation_current = 0x06;
+			break;
+		case 500:
+			rtd->excitation_current = 0x07;
+			break;
+		case 1000:
+			rtd->excitation_current = 0x08;
+			break;
+		default:
+			dev_err(&st->spi->dev,
+				"Invalid value for excitation current(%u)",
+							excitation_current);
+			ret = -EINVAL;
+			goto fail;
+		}
+	}
+
+	of_property_read_u32(child, "adi,rtd-curve", &rtd->rtd_curve);
+
+	of_node_put(phandle);
+	return &rtd->sensor;
+fail:
+	of_node_put(phandle);
+	return ERR_PTR(ret);
+}
+
+static struct ltc2983_sensor *ltc2983_thermistor_new(
+					const struct device_node *child,
+					struct ltc2983_data *st,
+					const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_thermistor *thermistor;
+	struct device *dev = &st->spi->dev;
+	struct device_node *phandle;
+	u32 excitation_current = 0;
+	int ret = 0;
+
+	thermistor = devm_kzalloc(dev, sizeof(*thermistor), GFP_KERNEL);
+	if (!thermistor)
+		return ERR_PTR(-ENOMEM);
+
+	phandle = of_parse_phandle(child, "adi,rsense-handle", 0);
+	if (!phandle) {
+		dev_err(dev, "Property adi,rsense-handle missing or invalid");
+		return ERR_PTR(-EINVAL);
+	}
+
+	ret = of_property_read_u32(phandle, "reg", &thermistor->r_sense_chan);
+	if (ret) {
+		dev_err(dev, "rsense channel must be configured...\n");
+		goto fail;
+	}
+
+	of_property_read_u32(child, "adi,sensor-config",
+			     &thermistor->sensor_config);
+	/* validate channel index */
+	if (!(thermistor->sensor_config & LTC2983_THERMISTOR_DIFF_MASK) &&
+	    sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+		dev_err(&st->spi->dev,
+			"Invalid chann:%d for differential thermistor",
+								sensor->chan);
+		ret = -EINVAL;
+		goto fail;
+	}
+
+	/* check custom sensor */
+	if (sensor->type >= LTC2983_SENSOR_THERMISTOR_STEINHART) {
+		thermistor->custom = __ltc2983_custom_sensor_new(st, child,
+			sensor->type == LTC2983_SENSOR_THERMISTOR_STEINHART ?
+							  true : false, 64,
+							  false);
+		if (IS_ERR(thermistor->custom)) {
+			of_node_put(phandle);
+			return ERR_CAST(thermistor->custom);
+		}
+	}
+	/* set common parameters */
+	thermistor->sensor.fault_handler = ltc2983_common_fault_handler;
+	thermistor->sensor.assign_chan = ltc2983_thermistor_assign_chan;
+
+	ret = of_property_read_u32(child, "adi,excitation-current-nanoamp",
+				   &excitation_current);
+	if (ret) {
+		/* Auto range is not allowed for custom sensors */
+		if (sensor->type >= LTC2983_SENSOR_THERMISTOR_STEINHART)
+			/* default to 1uA */
+			thermistor->excitation_current = 0x03;
+		else
+			/* default to auto-range */
+			thermistor->excitation_current = 0x0c;
+	} else {
+		switch (excitation_current) {
+		case 0:
+			/* auto range */
+			if (sensor->type >=
+			    LTC2983_SENSOR_THERMISTOR_STEINHART) {
+				dev_err(&st->spi->dev,
+					"Auto Range not allowed for custom sensors\n");
+				ret = -EINVAL;
+				goto fail;
+			}
+			thermistor->excitation_current = 0x0c;
+			break;
+		case 250:
+			thermistor->excitation_current = 0x01;
+			break;
+		case 500:
+			thermistor->excitation_current = 0x02;
+			break;
+		case 1000:
+			thermistor->excitation_current = 0x03;
+			break;
+		case 5000:
+			thermistor->excitation_current = 0x04;
+			break;
+		case 10000:
+			thermistor->excitation_current = 0x05;
+			break;
+		case 25000:
+			thermistor->excitation_current = 0x06;
+			break;
+		case 50000:
+			thermistor->excitation_current = 0x07;
+			break;
+		case 100000:
+			thermistor->excitation_current = 0x08;
+			break;
+		case 250000:
+			thermistor->excitation_current = 0x09;
+			break;
+		case 500000:
+			thermistor->excitation_current = 0x0a;
+			break;
+		case 1000000:
+			thermistor->excitation_current = 0x0b;
+			break;
+		default:
+			dev_err(&st->spi->dev,
+				"Invalid value for excitation current(%u)",
+							excitation_current);
+			ret = -EINVAL;
+			goto fail;
+		}
+	}
+
+	of_node_put(phandle);
+	return &thermistor->sensor;
+fail:
+	of_node_put(phandle);
+	return ERR_PTR(ret);
+}
+
+static struct ltc2983_sensor *ltc2983_diode_new(
+					const struct device_node *child,
+					const struct ltc2983_data *st,
+					const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_diode *diode;
+	u32 temp = 0, excitation_current = 0;
+	int ret;
+
+	diode = devm_kzalloc(&st->spi->dev, sizeof(*diode), GFP_KERNEL);
+	if (!diode)
+		return ERR_PTR(-ENOMEM);
+
+	of_property_read_u32(child, "adi,sensor-config", &diode->sensor_config);
+	/* validate channel index */
+	if (!(diode->sensor_config & LTC2983_DIODE_DIFF_MASK) &&
+	    sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+		dev_err(&st->spi->dev,
+			"Invalid chann:%d for differential thermistor",
+								sensor->chan);
+		return ERR_PTR(-EINVAL);
+	}
+	/* set common parameters */
+	diode->sensor.fault_handler = ltc2983_common_fault_handler;
+	diode->sensor.assign_chan = ltc2983_diode_assign_chan;
+
+	ret = of_property_read_u32(child, "adi,excitation-current-microamp",
+				   &excitation_current);
+	if (!ret) {
+		switch (excitation_current) {
+		case 10:
+			diode->excitation_current = 0x00;
+			break;
+		case 20:
+			diode->excitation_current = 0x01;
+			break;
+		case 40:
+			diode->excitation_current = 0x02;
+			break;
+		case 80:
+			diode->excitation_current = 0x03;
+			break;
+		default:
+			dev_err(&st->spi->dev,
+				"Invalid value for excitation current(%u)",
+							excitation_current);
+			return ERR_PTR(-EINVAL);
+		}
+	}
+
+	of_property_read_u32(child, "adi,ideal-factor-value", &temp);
+
+	/* 2^20 resolution */
+	diode->ideal_factor_value = __convert_to_raw(temp, 1048576);
+
+	return &diode->sensor;
+}
+
+static struct ltc2983_sensor *ltc2983_r_sense_new(struct device_node *child,
+					struct ltc2983_data *st,
+					const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_rsense *rsense;
+	int ret;
+	u64 temp;
+
+	rsense = devm_kzalloc(&st->spi->dev, sizeof(*rsense), GFP_KERNEL);
+	if (!rsense)
+		return ERR_PTR(-ENOMEM);
+
+	/* validate channel index */
+	if (sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+		dev_err(&st->spi->dev, "Invalid chann:%d for r_sense",
+							sensor->chan);
+		return ERR_PTR(-EINVAL);
+	}
+	/* get raw value */
+	ret = of_property_read_u64(child, "adi,rsense-val-micro-ohms", &temp);
+	if (ret) {
+		dev_err(&st->spi->dev, "Property adi,rsense-val-micro-ohms missing\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	/* 2^10 resolution */
+	rsense->r_sense_val = __convert_to_raw(temp, 1024);
+
+	/* set common parameters */
+	rsense->sensor.assign_chan = ltc2983_r_sense_assign_chan;
+
+	return &rsense->sensor;
+}
+
+static struct ltc2983_sensor *ltc2983_adc_new(struct device_node *child,
+					 struct ltc2983_data *st,
+					 const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_adc *adc;
+
+	adc = devm_kzalloc(&st->spi->dev, sizeof(*adc), GFP_KERNEL);
+	if (!adc)
+		return ERR_PTR(-ENOMEM);
+
+	if (of_property_read_bool(child, "adi,single-ended"))
+		adc->single_ended = true;
+
+	if (!adc->single_ended &&
+	    sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+		dev_err(&st->spi->dev, "Invalid chan:%d for differential adc\n",
+								sensor->chan);
+		return ERR_PTR(-EINVAL);
+	}
+	/* set common parameters */
+	adc->sensor.assign_chan = ltc2983_adc_assign_chan;
+	adc->sensor.fault_handler = ltc2983_common_fault_handler;
+
+	return &adc->sensor;
+}
+
+static int ltc2983_chan_read(struct ltc2983_data *st,
+			const struct ltc2983_sensor *sensor, int *val)
+{
+	u32 start_conversion = 0;
+	int ret;
+	unsigned long time;
+	__be32 temp;
+
+	/*
+	 * Do not allow channel readings if device is in sleep state.
+	 * A read/write on the spi bus would bring the device prematurely
+	 * out of sleep.
+	 */
+	if (st->sleep)
+		return -EPERM;
+
+	start_conversion = LTC2983_STATUS_START(true);
+	start_conversion |= LTC2983_STATUS_CHAN_SEL(sensor->chan);
+	dev_dbg(&st->spi->dev, "Start conversion on chan:%d, status:%02X\n",
+		sensor->chan, start_conversion);
+	/* start conversion */
+	ret = regmap_write(st->regmap, LTC2983_STATUS_REG, start_conversion);
+	if (ret)
+		return ret;
+
+	reinit_completion(&st->completion);
+	/*
+	 * wait for conversion to complete.
+	 * 300 ms should be more than enough to complete the conversion.
+	 * Depending on the sensor configuration, there are 2/3 conversions
+	 * cycles of 82ms.
+	 */
+	time = wait_for_completion_timeout(&st->completion,
+					   msecs_to_jiffies(300));
+	if (!time) {
+		dev_warn(&st->spi->dev, "Conversion timed out\n");
+		return -ETIMEDOUT;
+	}
+
+	/* read the converted data */
+	ret = regmap_bulk_read(st->regmap, LTC2983_CHAN_RES_ADDR(sensor->chan),
+			       &temp, sizeof(temp));
+	if (ret)
+		return ret;
+
+	*val = __be32_to_cpu(temp);
+
+	if (!(LTC2983_RES_VALID_MASK & *val)) {
+		dev_err(&st->spi->dev, "Invalid conversion detected\n");
+		return -EIO;
+	}
+
+	ret = sensor->fault_handler(st, *val);
+	if (ret)
+		return ret;
+
+	*val = sign_extend32((*val) & LTC2983_DATA_MASK, LTC2983_DATA_SIGN_BIT);
+	return 0;
+}
+
+static int ltc2983_read_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int *val, int *val2, long mask)
+{
+	struct ltc2983_data *st = iio_priv(indio_dev);
+	int ret;
+
+	/* sanity check */
+	if (chan->address >= st->num_channels) {
+		dev_err(&st->spi->dev, "Invalid chan address:%ld",
+							chan->address);
+		return -EINVAL;
+	}
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		mutex_lock(&st->lock);
+		ret = ltc2983_chan_read(st, st->sensors[chan->address], val);
+		mutex_unlock(&st->lock);
+		return ret ?: IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_TEMP:
+			/* value in milli degrees */
+			*val = 1000;
+			/* 2^10 */
+			*val2 = 1024;
+			return IIO_VAL_FRACTIONAL;
+		case IIO_VOLTAGE:
+			/* value in millivolt */
+			*val = 1000;
+			/* 2^21 */
+			*val2 = 2097152;
+			return IIO_VAL_FRACTIONAL;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return -EINVAL;
+}
+
+static int ltc2983_reg_access(struct iio_dev *indio_dev,
+			      unsigned int reg,
+			      unsigned int writeval,
+			      unsigned int *readval)
+{
+	struct ltc2983_data *st = iio_priv(indio_dev);
+
+	/* check comment in ltc2983_chan_read() */
+	if (st->sleep)
+		return -EPERM;
+
+	if (readval)

drivers/iio/temperature/ltc2983.c line 1114

Quoted 10 lines
drivers/iio/temperature/ltc2983.c new file +10 -0
+		return regmap_read(st->regmap, reg, readval);
+	else
+		return regmap_write(st->regmap, reg, writeval);
+}
+
+static irqreturn_t ltc2983_irq_handler(int irq, void *data)
+{
+	struct ltc2983_data *st = data;
+
+	complete(&st->completion);

This is a rare case where I'm not sure a threaded irq actually makes sense. We may be better off just doing this in a traditional top half, rather than spinning up a thread just to set completion.

Quoted 322 lines
drivers/iio/temperature/ltc2983.c new file +322 -0
+	return IRQ_HANDLED;
+}
+
+#define LTC2983_CHAN(__type, index, __address) ({ \
+	struct iio_chan_spec __chan = { \
+		.type = __type, \
+		.indexed = 1, \
+		.channel = index, \
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
+		.address = __address, \
+	}; \
+	__chan; \
+})
+
+static int ltc2983_parse_dt(struct ltc2983_data *st)
+{
+	struct device_node *child;
+	struct device *dev = &st->spi->dev;
+	int ret = 0, chan = 0, channel_avail_mask = 0;
+
+	if (!of_property_read_bool(dev->of_node, "adi,temperature-celcius"))
+		st->temp_farenheit = true;
+
+	of_property_read_u32(dev->of_node, "adi,mux-delay-config-us",
+			     &st->mux_delay_config);
+
+	of_property_read_u32(dev->of_node, "adi,filter-notch-freq",
+			     &st->filter_notch_freq);
+
+	st->num_channels = of_get_available_child_count(dev->of_node);
+	st->sensors = devm_kcalloc(dev, st->num_channels, sizeof(*st->sensors),
+				   GFP_KERNEL);
+	if (!st->sensors)
+		return -ENOMEM;
+
+	st->iio_channels = st->num_channels;
+	for_each_available_child_of_node(dev->of_node, child) {
+		struct ltc2983_sensor sensor;
+
+		ret = of_property_read_u32(child, "reg", &sensor.chan);
+		if (ret) {
+			dev_err(dev, "reg property must given for child nodes\n");
+			return ret;
+		}
+
+		/* check if we have a valid channel */
+		if (sensor.chan < LTC2983_MIN_CHANNELS_NR ||
+		    sensor.chan > LTC2983_MAX_CHANNELS_NR) {
+			dev_err(dev,
+				"chan:%d must be from 1 to 20\n", sensor.chan);
+			return -EINVAL;
+		} else if (channel_avail_mask & BIT(sensor.chan)) {
+			dev_err(dev, "chan:%d already in use\n", sensor.chan);
+			return -EINVAL;
+		}
+
+		ret = of_property_read_u32(child, "adi,sensor-type",
+					       &sensor.type);
+		if (ret) {
+			dev_err(dev,
+				"adi,sensor-type property must given for child nodes\n");
+			return ret;
+		}
+
+		dev_dbg(dev, "Create new sensor, type %u, chann %u",
+								sensor.type,
+								sensor.chan);
+
+		if (sensor.type >= LTC2983_SENSOR_THERMOCOUPLE &&
+		    sensor.type <= LTC2983_SENSOR_THERMOCOUPLE_CUSTOM) {
+			st->sensors[chan] = ltc2983_thermocouple_new(child, st,
+								     &sensor);
+		} else if (sensor.type >= LTC2983_SENSOR_RTD &&
+			   sensor.type <= LTC2983_SENSOR_RTD_CUSTOM) {
+			st->sensors[chan] = ltc2983_rtd_new(child, st, &sensor);
+		} else if (sensor.type >= LTC2983_SENSOR_THERMISTOR &&
+			   sensor.type <= LTC2983_SENSOR_THERMISTOR_CUSTOM) {
+			st->sensors[chan] = ltc2983_thermistor_new(child, st,
+								   &sensor);
+		} else if (sensor.type == LTC2983_SENSOR_DIODE) {
+			st->sensors[chan] = ltc2983_diode_new(child, st,
+							      &sensor);
+		} else if (sensor.type == LTC2983_SENSOR_SENSE_RESISTOR) {
+			st->sensors[chan] = ltc2983_r_sense_new(child, st,
+								&sensor);
+			/* don't add rsense to iio */
+			st->iio_channels--;
+		} else if (sensor.type == LTC2983_SENSOR_DIRECT_ADC) {
+			st->sensors[chan] = ltc2983_adc_new(child, st, &sensor);
+		} else {
+			dev_err(dev, "Unknown sensor type %d\n", sensor.type);
+			return -EINVAL;
+		}
+
+		if (IS_ERR(st->sensors[chan])) {
+			dev_err(dev, "Failed to create sensor %ld",
+						PTR_ERR(st->sensors[chan]));
+			return PTR_ERR(st->sensors[chan]);
+		}
+		/* set generic sensor parameters */
+		st->sensors[chan]->chan = sensor.chan;
+		st->sensors[chan]->type = sensor.type;
+
+		channel_avail_mask |= BIT(sensor.chan);
+		chan++;
+	}
+
+	return 0;
+}
+
+static int ltc2983_setup(struct ltc2983_data *st, bool assign_iio)
+{
+	u32 iio_chan_t = 0, iio_chan_v = 0, chan, iio_idx = 0;
+	u32 global_cfg = 0;
+	int ret;
+	unsigned long time;
+
+	/* make sure the device is up */
+	time = wait_for_completion_timeout(&st->completion,
+					    msecs_to_jiffies(250));
+
+	if (!time) {
+		dev_err(&st->spi->dev, "Device startup timed out\n");
+		return -ETIMEDOUT;
+	}
+
+	st->iio_chan = devm_kzalloc(&st->spi->dev,
+				    st->iio_channels * sizeof(*st->iio_chan),
+				    GFP_KERNEL);
+
+	if (!st->iio_chan)
+		return -ENOMEM;
+
+	global_cfg = LTC2983_NOTCH_FREQ(st->filter_notch_freq);
+	global_cfg |= LTC2983_TEMP_UNITS(st->temp_farenheit);
+	regmap_write(st->regmap, LTC2983_GLOBAL_CONFIG_REG, global_cfg);
+	regmap_write(st->regmap, LTC2983_MUX_CONFIG_REG, st->mux_delay_config);
+
+	for (chan = 0; chan < st->num_channels; chan++) {
+		u32 chan_type = 0, *iio_chan;
+
+		ret = st->sensors[chan]->assign_chan(st, st->sensors[chan]);
+		if (ret)
+			return ret;
+		/*
+		 * The assign_iio flag is necessary for when the device is
+		 * coming out of sleep. In that case, we just need to
+		 * re-configure the device channels.
+		 * We also don't assign iio channels for rsense.
+		 */
+		if (st->sensors[chan]->type == LTC2983_SENSOR_SENSE_RESISTOR ||
+		    !assign_iio)
+			continue;
+
+		/* assign iio channel */
+		if (st->sensors[chan]->type != LTC2983_SENSOR_DIRECT_ADC) {
+			chan_type = IIO_TEMP;
+			iio_chan = &iio_chan_t;
+		} else {
+			chan_type = IIO_VOLTAGE;
+			iio_chan = &iio_chan_v;
+		}
+
+		/*
+		 * add chan as the iio .address so that, we can directly
+		 * reference the sensor given the iio_chan_spec
+		 */
+		st->iio_chan[iio_idx++] = LTC2983_CHAN(chan_type, (*iio_chan)++,
+						       chan);
+	}
+
+	return 0;
+}
+
+static const struct regmap_range ltc2983_reg_ranges[] = {
+	regmap_reg_range(LTC2983_STATUS_REG, LTC2983_STATUS_REG),
+	regmap_reg_range(LTC2983_TEMP_RES_START_REG, LTC2983_TEMP_RES_END_REG),
+	regmap_reg_range(LTC2983_GLOBAL_CONFIG_REG, LTC2983_GLOBAL_CONFIG_REG),
+	regmap_reg_range(LTC2983_MULT_CHANNEL_START_REG,
+			 LTC2983_MULT_CHANNEL_END_REG),
+	regmap_reg_range(LTC2983_MUX_CONFIG_REG, LTC2983_MUX_CONFIG_REG),
+	regmap_reg_range(LTC2983_CHAN_ASSIGN_START_REG,
+			 LTC2983_CHAN_ASSIGN_END_REG),
+	regmap_reg_range(LTC2983_CUST_SENS_TBL_START_REG,
+			 LTC2983_CUST_SENS_TBL_END_REG),
+};
+
+static const struct regmap_access_table ltc2983_reg_table = {
+	.yes_ranges = ltc2983_reg_ranges,
+	.n_yes_ranges = ARRAY_SIZE(ltc2983_reg_ranges),
+};
+
+/*
+ *  The reg_bits are actually 12 but the device needs the first *complete*
+ *  byte for the command (R/W).
+ */
+static const struct regmap_config ltc2983_regmap_config = {
+	.reg_bits = 24,
+	.val_bits = 8,
+	.wr_table = &ltc2983_reg_table,
+	.rd_table = &ltc2983_reg_table,
+	.read_flag_mask = GENMASK(1, 0),
+	.write_flag_mask = BIT(1),
+};
+
+static const struct  iio_info ltc2983_iio_info = {
+	.read_raw = ltc2983_read_raw,
+	.debugfs_reg_access = ltc2983_reg_access,
+};
+
+static int ltc2983_probe(struct spi_device *spi)
+{
+	struct ltc2983_data *st;
+	struct iio_dev *indio_dev;
+	const char *name = spi_get_device_id(spi)->name;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	st = iio_priv(indio_dev);
+
+	st->regmap = devm_regmap_init_spi(spi, &ltc2983_regmap_config);
+	if (IS_ERR(st->regmap)) {
+		dev_err(&spi->dev, "Failed to initialize regmap\n");
+		return PTR_ERR(st->regmap);
+	}
+
+	mutex_init(&st->lock);
+	init_completion(&st->completion);
+	st->spi = spi;
+	spi_set_drvdata(spi, st);
+
+	ret = ltc2983_parse_dt(st);
+	if (ret)
+		return ret;
+	/*
+	 * let's request the irq now so it is used to sync the device
+	 * startup in ltc2983_setup()
+	 */
+	ret = devm_request_threaded_irq(&spi->dev, spi->irq, NULL,
+					ltc2983_irq_handler, IRQF_ONESHOT |
+					IRQF_TRIGGER_RISING, name, st);
+	if (ret) {
+		dev_err(&spi->dev, "failed to request an irq, %d", ret);
+		return ret;
+	}
+
+	ret = ltc2983_setup(st, true);
+	if (ret)
+		return ret;
+
+	indio_dev->dev.parent = &spi->dev;
+	indio_dev->name = name;
+	indio_dev->num_channels = st->iio_channels;
+	indio_dev->channels = st->iio_chan;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &ltc2983_iio_info;
+
+	return devm_iio_device_register(&spi->dev, indio_dev);
+}
+
+static int __maybe_unused ltc2983_resume(struct device *dev)
+{
+	struct ltc2983_data *st = spi_get_drvdata(to_spi_device(dev));
+	int ret;
+
+	mutex_lock(&st->lock);
+	/* dummy read to bring the device out of sleep */
+	regmap_read(st->regmap, LTC2983_STATUS_REG, &ret);
+	/* we need to re-assign the channels */
+	ret = ltc2983_setup(st, false);
+	st->sleep = false;
+	mutex_unlock(&st->lock);
+
+	return ret;
+}
+
+static int __maybe_unused ltc2983_suspend(struct device *dev)
+{
+	struct ltc2983_data *st = spi_get_drvdata(to_spi_device(dev));
+	int ret;
+
+	mutex_lock(&st->lock);
+	ret = regmap_write(st->regmap, LTC2983_STATUS_REG, LTC2983_SLEEP);
+	st->sleep = true;
+	mutex_unlock(&st->lock);
+
+	return ret;
+}
+
+static SIMPLE_DEV_PM_OPS(ltc2983_pm_ops, ltc2983_suspend, ltc2983_resume);
+
+static const struct spi_device_id ltc2983_id_table[] = {
+	{ "ltc2983" },
+	{},
+};
+MODULE_DEVICE_TABLE(spi, ltc2983_id_table);
+
+static const struct of_device_id ltc2983_of_match[] = {
+	{ .compatible = "adi,ltc2983" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ltc2983_id_table);
+
+static struct spi_driver ltc2983_driver = {
+	.driver = {
+		.name = "ltc2983",
+		.of_match_table = ltc2983_of_match,
+		.pm = &ltc2983_pm_ops,
+	},
+	.probe = ltc2983_probe,
+	.id_table = ltc2983_id_table,
+};
+
+module_spi_driver(ltc2983_driver);
+
+MODULE_AUTHOR("Nuno Sa <[email protected]>");
+MODULE_DESCRIPTION("Analog Devices LTC2983 SPI Temperature sensors");
+MODULE_LICENSE("GPL");
author maintainer
#5 lore raw
Quoted 12 lines · Jonathan Cameron
Quoted 8 lines · On Mon, 30 Sep 2019 12:42:46 +0200 Nuno Sá <[email protected]> wrote:

The LTC2983 is a Multi-Sensor High Accuracy Digital Temperature Measurement System. It measures a wide variety of temperature sensors and
digitally outputs the result, in °C or °F, with 0.1°C accuracy and 0.001°C resolution. It can measure the temperature of all standard thermocouples (type B,E,J,K,N,S,R,T), standard 2-,3-,4-wire RTDs, thermistors and diodes.

Quoted 6 lines
Quoted 1 line

One minor comment inline. I don't see a reason to use a threaded irq to simply set a completion. Just do it with a traditional irq. I suspect the overhead of doing that is probably similar to spinning up the irq thread.

ack.

Quoted 1,735 lines

Otherwise, I'm happy with this subject to binding review.

Thanks,

Jonathan

Quoted 1,352 lines

---
Changes in v2:
* Added some needed blank lines (for readability);
* Allocate iio_chan in the setup() function;
* Rename reset to sleep;
* Remove unneeded dev_dbg calls;
* Remove unneeded line wrapping;
* Remove unneeded comments;
* Remove extend_names. Use the standard ABI;
* Adapt the scales to report in millivolt and milli degrees;
* Adapt the of_property readings to the renaming of the
properties;
* For custom thermistors, excitation-current cannot be set to Auto
range.

 MAINTAINERS                       |    7 +
 drivers/iio/temperature/Kconfig   |   10 +
 drivers/iio/temperature/Makefile  |    1 +
 drivers/iio/temperature/ltc2983.c | 1436
+++++++++++++++++++++++++++++
 4 files changed, 1454 insertions(+)
 create mode 100644 drivers/iio/temperature/ltc2983.c
MAINTAINERS +7 -0
index f0c03740b9fb..14a256e785ca 100644
@@ -9491,6 +9491,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/iio/dac/ltc1660.txt
 F:	drivers/iio/dac/ltc1660.c
 
+LTC2983 IIO TEMPERATURE DRIVER
+M:	Nuno Sá <[email protected]>
+W:	http://ez.analog.com/community/linux-device-drivers
+L:	[email protected]
+S:	Supported
+F:	drivers/iio/temperature/ltc2983.c
+
 LTC4261 HARDWARE MONITOR DRIVER
 M:	Guenter Roeck <[email protected]>
 L:	[email protected]
drivers/iio/temperature/Kconfig +2 -0
index 737faa0901fe..04b5a67b593c 100644
@@ -4,6 +4,16 @@
 #
 menu "Temperature sensors"
 
+config LTC2983
+	tristate "Analog Devices Multi-Sensor Digital Temperature

Measurement System"

drivers/iio/temperature/Kconfig +8 -0
+	depends on SPI
+	help
+	  Say yes here to build support for the LTC2983 Multi-Sensor
+	  high accuracy digital temperature measurement system.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called ltc2983.
+
 config MAXIM_THERMOCOUPLE
 	tristate "Maxim thermocouple sensors"
 	depends on SPI
drivers/iio/temperature/Makefile +1 -0
index baca4776ca0d..d6b850b0cf63 100644
@@ -3,6 +3,7 @@
 # Makefile for industrial I/O temperature drivers
 #
 
+obj-$(CONFIG_LTC2983) += ltc2983.o
 obj-$(CONFIG_HID_SENSOR_TEMP) += hid-sensor-temperature.o
 obj-$(CONFIG_MAXIM_THERMOCOUPLE) += maxim_thermocouple.o
 obj-$(CONFIG_MAX31856) += max31856.o
drivers/iio/temperature/ltc2983.c new file +3 -0
new file mode 100644
index 000000000000..7c159da9f183
@@ -0,0 +1,1436 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Analog Devices LTC2983 Multi-Sensor Digital Temperature

Measurement System
+ * driver
+ *
+ * Copyright 2019 Analog Devices Inc.
+ */

drivers/iio/temperature/ltc2983.c new file +35 -0
+#include <linux/bitfield.h>
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/iio/iio.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+/* register map */
+#define LTC2983_STATUS_REG			0x0000
+#define LTC2983_TEMP_RES_START_REG		0x0010
+#define LTC2983_TEMP_RES_END_REG		0x005F
+#define LTC2983_GLOBAL_CONFIG_REG		0x00F0
+#define LTC2983_MULT_CHANNEL_START_REG		0x00F4
+#define LTC2983_MULT_CHANNEL_END_REG		0x00F7
+#define LTC2983_MUX_CONFIG_REG			0x00FF
+#define LTC2983_CHAN_ASSIGN_START_REG		0x0200
+#define LTC2983_CHAN_ASSIGN_END_REG		0x024F
+#define LTC2983_CUST_SENS_TBL_START_REG		0x0250
+#define LTC2983_CUST_SENS_TBL_END_REG		0x03CF
+
+#define LTC2983_DIFFERENTIAL_CHAN_MIN		2
+#define LTC2983_MAX_CHANNELS_NR			20
+#define LTC2983_MIN_CHANNELS_NR			1
+#define LTC2983_SLEEP				0x97
+#define LTC2983_CUSTOM_STEINHART_SIZE		24
+#define LTC2983_CUSTOM_SENSOR_ENTRY_SZ		6
+#define LTC2983_CUSTOM_STEINHART_ENTRY_SZ	4
+
+#define LTC2983_CHAN_START_ADDR(chan) \
+			(((chan - 1) * 4) +

LTC2983_CHAN_ASSIGN_START_REG)

drivers/iio/temperature/ltc2983.c new file +14 -0
+#define LTC2983_CHAN_RES_ADDR(chan) \
+			(((chan - 1) * 4) + LTC2983_TEMP_RES_START_REG)
+#define LTC2983_THERMOCOUPLE_DIFF_MASK		BIT(3)
+#define LTC2983_THERMISTOR_DIFF_MASK		BIT(2)
+#define LTC2983_DIODE_DIFF_MASK			BIT(2)
+#define LTC2983_RTD_4_WIRE_MASK			BIT(3)
+#define LTC2983_RTD_ROTATION_MASK		BIT(1)
+#define LTC2983_RTD_KELVIN_R_SENSE_MASK		GENMASK(3, 2)
+
+#define LTC2983_COMMON_HARD_FAULT_MASK	GENMASK(31, 30)
+#define LTC2983_COMMON_SOFT_FAULT_MASK	GENMASK(27, 25)
+
+#define	LTC2983_STATUS_START_MASK	BIT(7)
+#define	LTC2983_STATUS_START(x)		FIELD_PREP(LTC2983_

STATUS_START_MASK, x)

drivers/iio/temperature/ltc2983.c new file +4 -0
+
+#define	LTC2983_STATUS_CHAN_SEL_MASK	GENMASK(4, 0)
+#define	LTC2983_STATUS_CHAN_SEL(x) \
+				FIELD_PREP(LTC2983_STATUS_CHAN_SEL_MASK

, x)

drivers/iio/temperature/ltc2983.c new file +3 -0
+
+#define LTC2983_TEMP_UNITS_MASK		BIT(2)
+#define LTC2983_TEMP_UNITS(x)		FIELD_PREP(LTC2983_TEMP

_UNITS_MASK, x)

drivers/iio/temperature/ltc2983.c new file +3 -0
+
+#define LTC2983_NOTCH_FREQ_MASK		GENMASK(1, 0)
+#define LTC2983_NOTCH_FREQ(x)		FIELD_PREP(LTC2983_NOTC

H_FREQ_MASK, x)

drivers/iio/temperature/ltc2983.c new file +7 -0
+
+#define LTC2983_RES_VALID_MASK		BIT(24)
+#define LTC2983_DATA_MASK		GENMASK(23, 0)
+#define LTC2983_DATA_SIGN_BIT		23
+
+#define LTC2983_CHAN_TYPE_MASK		GENMASK(31, 27)
+#define LTC2983_CHAN_TYPE(x)		FIELD_PREP(LTC2983_CHAN

_TYPE_MASK, x)

drivers/iio/temperature/ltc2983.c new file +2 -0
+
+/* cold junction for thermocouples and rsense for rtd's and

thermistor's */

drivers/iio/temperature/ltc2983.c new file +2 -0
+#define LTC2983_CHAN_ASSIGN_MASK	GENMASK(26, 22)
+#define LTC2983_CHAN_ASSIGN(x)		FIELD_PREP(LTC2983_CHAN

_ASSIGN_MASK, x)

drivers/iio/temperature/ltc2983.c new file +3 -0
+
+#define LTC2983_CUSTOM_LEN_MASK		GENMASK(5, 0)
+#define LTC2983_CUSTOM_LEN(x)		FIELD_PREP(LTC2983_CUST

OM_LEN_MASK, x)

drivers/iio/temperature/ltc2983.c new file +3 -0
+
+#define LTC2983_CUSTOM_ADDR_MASK	GENMASK(11, 6)
+#define LTC2983_CUSTOM_ADDR(x)		FIELD_PREP(LTC2983_CUST

OM_ADDR_MASK, x)

drivers/iio/temperature/ltc2983.c new file +4 -0
+
+#define LTC2983_THERMOCOUPLE_CFG_MASK	GENMASK(21, 18)
+#define LTC2983_THERMOCOUPLE_CFG(x) \
+				FIELD_PREP(LTC2983_THERMOCOUPLE_CFG_MAS

K, x)

drivers/iio/temperature/ltc2983.c new file +5 -0
+#define LTC2983_THERMOCOUPLE_HARD_FAULT_MASK	GENMASK(31, 29)
+#define LTC2983_THERMOCOUPLE_SOFT_FAULT_MASK	GENMASK(28, 25)
+
+#define LTC2983_RTD_CFG_MASK		GENMASK(21, 18)
+#define LTC2983_RTD_CFG(x)		FIELD_PREP(LTC2983_RTD_CFG_MASK

, x)

drivers/iio/temperature/ltc2983.c new file +3 -0
+#define LTC2983_RTD_EXC_CURRENT_MASK	GENMASK(17, 14)
+#define LTC2983_RTD_EXC_CURRENT(x) \
+				FIELD_PREP(LTC2983_RTD_EXC_CURRENT_MASK

, x)

drivers/iio/temperature/ltc2983.c new file +2 -0
+#define LTC2983_RTD_CURVE_MASK		GENMASK(13, 12)
+#define LTC2983_RTD_CURVE(x)		FIELD_PREP(LTC2983_RTD_

CURVE_MASK, x)

drivers/iio/temperature/ltc2983.c new file +4 -0
+
+#define LTC2983_THERMISTOR_CFG_MASK	GENMASK(21, 19)
+#define LTC2983_THERMISTOR_CFG(x) \
+				FIELD_PREP(LTC2983_THERMISTOR_CFG_MASK,

x)

drivers/iio/temperature/ltc2983.c new file +3 -0
+#define LTC2983_THERMISTOR_EXC_CURRENT_MASK	GENMASK(18, 15)
+#define LTC2983_THERMISTOR_EXC_CURRENT(x) \
+			FIELD_PREP(LTC2983_THERMISTOR_EXC_CURRENT_MASK,

x)

drivers/iio/temperature/ltc2983.c new file +3 -0
+
+#define LTC2983_DIODE_CFG_MASK		GENMASK(26, 24)
+#define LTC2983_DIODE_CFG(x)		FIELD_PREP(LTC2983_DIOD

E_CFG_MASK, x)

drivers/iio/temperature/ltc2983.c new file +3 -0
+#define LTC2983_DIODE_EXC_CURRENT_MASK	GENMASK(23, 22)
+#define LTC2983_DIODE_EXC_CURRENT(x) \
+				FIELD_PREP(LTC2983_DIODE_EXC_CURRENT_MA

SK, x)

drivers/iio/temperature/ltc2983.c new file +3 -0
+#define LTC2983_DIODE_IDEAL_FACTOR_MASK	GENMASK(21, 0)
+#define LTC2983_DIODE_IDEAL_FACTOR(x) \
+				FIELD_PREP(LTC2983_DIODE_IDEAL_FACTOR_M

ASK, x)

drivers/iio/temperature/ltc2983.c new file +3 -0
+
+#define LTC2983_R_SENSE_VAL_MASK	GENMASK(26, 0)
+#define LTC2983_R_SENSE_VAL(x)		FIELD_PREP(LTC2983_R_SE

NSE_VAL_MASK, x)

drivers/iio/temperature/ltc2983.c new file +4 -0
+
+#define LTC2983_ADC_SINGLE_ENDED_MASK	BIT(26)
+#define LTC2983_ADC_SINGLE_ENDED(x) \
+				FIELD_PREP(LTC2983_ADC_SINGLE_ENDED_MAS

K, x)

drivers/iio/temperature/ltc2983.c new file +16 -0
+
+enum {
+	LTC2983_SENSOR_THERMOCOUPLE = 1,
+	LTC2983_SENSOR_THERMOCOUPLE_CUSTOM = 9,
+	LTC2983_SENSOR_RTD = 10,
+	LTC2983_SENSOR_RTD_CUSTOM = 18,
+	LTC2983_SENSOR_THERMISTOR = 19,
+	LTC2983_SENSOR_THERMISTOR_STEINHART = 26,
+	LTC2983_SENSOR_THERMISTOR_CUSTOM = 27,
+	LTC2983_SENSOR_DIODE = 28,
+	LTC2983_SENSOR_SENSE_RESISTOR = 29,
+	LTC2983_SENSOR_DIRECT_ADC = 30,
+};
+
+#define to_thermocouple(_sensor) \
+		container_of(_sensor, struct ltc2983_thermocouple,

sensor)

drivers/iio/temperature/ltc2983.c new file +6 -0
+
+#define to_rtd(_sensor) \
+		container_of(_sensor, struct ltc2983_rtd, sensor)
+
+#define to_thermistor(_sensor) \
+		container_of(_sensor, struct ltc2983_thermistor,

sensor)

drivers/iio/temperature/ltc2983.c new file +28 -0
+
+#define to_diode(_sensor) \
+		container_of(_sensor, struct ltc2983_diode, sensor)
+
+#define to_rsense(_sensor) \
+		container_of(_sensor, struct ltc2983_rsense, sensor)
+
+#define to_adc(_sensor) \
+		container_of(_sensor, struct ltc2983_adc, sensor)
+
+struct ltc2983_data {
+	struct regmap *regmap;
+	struct spi_device *spi;
+	struct mutex lock;
+	struct completion completion;
+	struct iio_chan_spec *iio_chan;
+	struct ltc2983_sensor **sensors;
+	u32 mux_delay_config;
+	u32 filter_notch_freq;
+	u16 custom_table_size;
+	u8 num_channels;
+	u8 iio_channels;
+	bool temp_farenheit;
+	bool sleep;
+};
+
+struct ltc2983_sensor {
+	int (*fault_handler)(const struct ltc2983_data *st, const u32

result);

drivers/iio/temperature/ltc2983.c new file +61 -0
+	int (*assign_chan)(struct ltc2983_data *st,
+			   const struct ltc2983_sensor *sensor);
+	/* specifies the sensor channel */
+	u32 chan;
+	/* sensor type */
+	u32 type;
+};
+
+struct ltc2983_custom_sensor {
+	/* raw table sensor data */
+	u8 *table;
+	size_t size;
+	/* address offset */
+	s8 offset;
+	bool is_steinhart;
+};
+
+struct ltc2983_thermocouple {
+	struct ltc2983_sensor sensor;
+	struct ltc2983_custom_sensor *custom;
+	u32 sensor_config;
+	u32 cold_junction_chan;
+};
+
+struct ltc2983_rtd {
+	struct ltc2983_sensor sensor;
+	struct ltc2983_custom_sensor *custom;
+	u32 sensor_config;
+	u32 r_sense_chan;
+	u32 excitation_current;
+	u32 rtd_curve;
+};
+
+struct ltc2983_thermistor {
+	struct ltc2983_sensor sensor;
+	struct ltc2983_custom_sensor *custom;
+	u32 sensor_config;
+	u32 r_sense_chan;
+	u32 excitation_current;
+};
+
+struct ltc2983_diode {
+	struct ltc2983_sensor sensor;
+	u32 sensor_config;
+	u32 excitation_current;
+	u32 ideal_factor_value;
+};
+
+struct ltc2983_rsense {
+	struct ltc2983_sensor sensor;
+	u32 r_sense_val;
+};
+
+struct ltc2983_adc {
+	struct ltc2983_sensor sensor;
+	bool single_ended;
+};
+
+/*
+ * Convert to Q format numbers. These number's are integers where
+ * the number of integer and fractional bits are specified. The

resolution
+ * is given by 1/@resolution and tell us the number of fractional bits. For
+ * instance a resolution of 2^-10 means we have 10 fractional bits.
+ */

drivers/iio/temperature/ltc2983.c new file +5 -0
+static u32 __convert_to_raw(const u64 val, const u32 resolution)
+{
+	u64 __res = val * resolution;
+
+	/* all values are multiplied by 1000000 to remove the fraction

*/

drivers/iio/temperature/ltc2983.c new file +6 -0
+	do_div(__res, 1000000);
+
+	return __res;
+}
+
+static u32 __convert_to_raw_sign(const u64 val, const u32

resolution)

drivers/iio/temperature/ltc2983.c new file +10 -0
+{
+	s64 __res = -(s32)val;
+
+	__res = __convert_to_raw(__res, resolution);
+
+	return (u32)-__res;
+}
+
+static int __ltc2983_fault_handler(const struct ltc2983_data *st,
+				   const u32 result, const u32

hard_mask,

drivers/iio/temperature/ltc2983.c new file +6 -0
+				   const u32 soft_mask)
+{
+	const struct device *dev = &st->spi->dev;
+
+	if (result & hard_mask) {
+		dev_err(dev, "Invalid conversion: Sensor HARD

fault\n");

drivers/iio/temperature/ltc2983.c new file +4 -0
+		return -EIO;
+	} else if (result & soft_mask) {
+		/* just print a warning */
+		dev_warn(dev, "Suspicious conversion: Sensor SOFT

fault\n");

drivers/iio/temperature/ltc2983.c new file +6 -0
+	}
+
+	return 0;
+}
+
+static int __ltc2983_chan_assign_common(const struct ltc2983_data

*st,

drivers/iio/temperature/ltc2983.c new file +1 -0
+					const struct ltc2983_sensor

*sensor,

drivers/iio/temperature/ltc2983.c new file +8 -0
+					u32 chan_val)
+{
+	u32 reg = LTC2983_CHAN_START_ADDR(sensor->chan);
+	__be32 __chan_val;
+
+	chan_val |= LTC2983_CHAN_TYPE(sensor->type);
+	dev_dbg(&st->spi->dev, "Assign reg:0x%04X, val:0x%08X\n", reg,
+								chan_va

l);

drivers/iio/temperature/ltc2983.c new file +6 -0
+	__chan_val = cpu_to_be32(chan_val);
+	return regmap_bulk_write(st->regmap, reg, &__chan_val,
+				 sizeof(__chan_val));
+}
+
+static int __ltc2983_chan_custom_sensor_assign(struct ltc2983_data

*st,

drivers/iio/temperature/ltc2983.c new file +1 -0
+					  struct ltc2983_custom_sensor

*custom,

drivers/iio/temperature/ltc2983.c new file +4 -0
+					  u32 *chan_val)
+{
+	u32 reg;
+	u8 mult = custom->is_steinhart ?

LTC2983_CUSTOM_STEINHART_ENTRY_SZ :

drivers/iio/temperature/ltc2983.c new file +6 -0
+		LTC2983_CUSTOM_SENSOR_ENTRY_SZ;
+	const struct device *dev = &st->spi->dev;
+	/*
+	 * custom->size holds the raw size of the table. However, when
+	 * configuring the sensor channel, we must write the number of
+	 * entries of the table minus 1. For steinhart sensors 0 is

written

drivers/iio/temperature/ltc2983.c new file +6 -0
+	 * since the size is constant!
+	 */
+	const u8 len = custom->is_steinhart ? 0 :
+		(custom->size / LTC2983_CUSTOM_SENSOR_ENTRY_SZ) - 1;
+	/*
+	 * Check if the offset was assigned already. It should be for

steinhart

drivers/iio/temperature/ltc2983.c new file +1 -0
+	 * sensors. When coming from sleep, it should be assigned for

all.

drivers/iio/temperature/ltc2983.c new file +4 -0
+	 */
+	if (custom->offset < 0) {
+		/*
+		 * This needs to be done again here because, from the

moment

drivers/iio/temperature/ltc2983.c new file +1 -0
+		 * when this test was done (successfully) for this

custom

drivers/iio/temperature/ltc2983.c new file +1 -0
+		 * sensor, a steinhart sensor might have been added

changing

drivers/iio/temperature/ltc2983.c new file +7 -0
+		 * custom_table_size...
+		 */
+		if (st->custom_table_size + custom->size >
+		    (LTC2983_CUST_SENS_TBL_END_REG -
+		     LTC2983_CUST_SENS_TBL_START_REG) + 1) {
+			dev_err(dev,
+				"Not space left(%d) for new custom

sensor(%zu)",

drivers/iio/temperature/ltc2983.c new file +1 -0
+							st-
Quoted 1 line

custom_table_size,

drivers/iio/temperature/ltc2983.c new file +10 -0
+							custom->size);
+			return -EINVAL;
+		}
+
+		custom->offset = st->custom_table_size /
+					LTC2983_CUSTOM_SENSOR_ENTRY_SZ;
+		st->custom_table_size += custom->size;
+	}
+
+	reg = (custom->offset * mult) +

LTC2983_CUST_SENS_TBL_START_REG;

drivers/iio/temperature/ltc2983.c new file +4 -0
+
+	*chan_val |= LTC2983_CUSTOM_LEN(len);
+	*chan_val |= LTC2983_CUSTOM_ADDR(custom->offset);
+	dev_dbg(dev, "Assign custom sensor, reg:0x%04X, off:%d,

sz:%zu",

drivers/iio/temperature/ltc2983.c new file +1 -0
+							reg, custom-
Quoted 1 line

offset,

drivers/iio/temperature/ltc2983.c new file +3 -0
+							custom->size);
+	/* write custom sensor table */
+	return regmap_bulk_write(st->regmap, reg, custom->table,

custom->size);

drivers/iio/temperature/ltc2983.c new file +4 -0
+}
+
+static struct ltc2983_custom_sensor *__ltc2983_custom_sensor_new(
+						struct ltc2983_data

*st,

drivers/iio/temperature/ltc2983.c new file +1 -0
+						const struct

device_node *np,

drivers/iio/temperature/ltc2983.c new file +1 -0
+						const bool

is_steinhart,

drivers/iio/temperature/ltc2983.c new file +8 -0
+						const u32 resolution,
+						const bool has_signed)
+{
+	struct ltc2983_custom_sensor *new_custom;
+	u8 index, n_entries, tbl = 0;
+	struct device *dev = &st->spi->dev;
+	/*
+	 * For custom steinhart, the full u32 is taken. For all the

others

drivers/iio/temperature/ltc2983.c new file +5 -0
+	 * the MSB is discarded.
+	 */
+	const u8 n_size = (is_steinhart == true) ? 4 : 3;
+
+	n_entries = of_property_count_elems_of_size(np, "adi,custom-

sensor",

drivers/iio/temperature/ltc2983.c new file +4 -0
+						sizeof(u64));
+	/* n_entries must be an even number */
+	if (!n_entries || (n_entries % 2) != 0) {
+		dev_err(dev, "Number of entries either 0 or not

even\n");

drivers/iio/temperature/ltc2983.c new file +4 -0
+		return ERR_PTR(-EINVAL);
+	}
+
+	new_custom = devm_kzalloc(dev, sizeof(*new_custom),

GFP_KERNEL);

drivers/iio/temperature/ltc2983.c new file +6 -0
+	if (!new_custom)
+		return ERR_PTR(-ENOMEM);
+
+	new_custom->size = n_entries * n_size;
+	/* check Steinhart size */
+	if (is_steinhart && new_custom->size !=

LTC2983_CUSTOM_STEINHART_SIZE) {

drivers/iio/temperature/ltc2983.c new file +2 -0
+		dev_err(dev, "Steinhart sensors size(%zu) must be 24",
+							new_custom-
Quoted 1 line

size);

drivers/iio/temperature/ltc2983.c new file +7 -0
+		return ERR_PTR(-EINVAL);
+	}
+	/* Check space on the table. */
+	if (st->custom_table_size + new_custom->size >
+	    (LTC2983_CUST_SENS_TBL_END_REG -
+	     LTC2983_CUST_SENS_TBL_START_REG) + 1) {
+		dev_err(dev, "No space left(%d) for new custom

sensor(%zu)",

drivers/iio/temperature/ltc2983.c new file +1 -0
+				st->custom_table_size, new_custom-
Quoted 1 line

size);

drivers/iio/temperature/ltc2983.c new file +5 -0
+		return ERR_PTR(-EINVAL);
+	}
+
+	/* allocate the table */
+	new_custom->table = devm_kzalloc(dev, new_custom->size,

GFP_KERNEL);

drivers/iio/temperature/ltc2983.c new file +7 -0
+	if (!new_custom->table)
+		return ERR_PTR(-ENOMEM);
+
+	for (index = 0; index < n_entries; index++) {
+		u64 temp = 0, j;
+
+		of_property_read_u64_index(np, "adi,custom-sensor",

index,

drivers/iio/temperature/ltc2983.c new file +3 -0
+					   &temp);
+		/*
+		 * Steinhart sensors are configured with raw values in

the

drivers/iio/temperature/ltc2983.c new file +1 -0
+		 * devicetree. For the other sensors we must convert

the

drivers/iio/temperature/ltc2983.c new file +1 -0
+		 * value to raw. The odd index's correspond to

temperarures

drivers/iio/temperature/ltc2983.c new file +1 -0
+		 * and always have 1/1024 of resolution. Temperatures

also

drivers/iio/temperature/ltc2983.c new file +7 -0
+		 * come in kelvin, so signed values is not possible
+		 */
+		if (!is_steinhart) {
+			if ((index % 2) != 0)
+				temp = __convert_to_raw(temp, 1024);
+			else if (has_signed && (s64)temp < 0)
+				temp = __convert_to_raw_sign(temp,

resolution);

drivers/iio/temperature/ltc2983.c new file +2 -0
+			else
+				temp = __convert_to_raw(temp,

resolution);

drivers/iio/temperature/ltc2983.c new file +10 -0
+		}
+
+		for (j = 0; j < n_size; j++)
+			new_custom->table[tbl++] =
+				temp >> (8 * (n_size - j - 1));
+	}
+
+	new_custom->is_steinhart = is_steinhart;
+	/*
+	 * This is done to first add all the steinhart sensors to the

table,

drivers/iio/temperature/ltc2983.c new file +1 -0
+	 * in order to maximize the table usage. If we mix adding

steinhart

drivers/iio/temperature/ltc2983.c new file +1 -0
+	 * with the other sensors, we might have to do some roundup to

make

drivers/iio/temperature/ltc2983.c new file +1 -0
+	 * sure that sensor_addr - 0x250(start address) is a multiple

of 4

drivers/iio/temperature/ltc2983.c new file +1 -0
+	 * (for steinhart), and a multiple of 6 for all the other

sensors.

drivers/iio/temperature/ltc2983.c new file +2 -0
+	 * Since we have const 24 bytes for steinhart sensors and 24 is
+	 * also a multiple of 6, we guarantee that the first non-

steinhart

drivers/iio/temperature/ltc2983.c new file +1 -0
+	 * sensor will sit in a correct address without the need of

filling

drivers/iio/temperature/ltc2983.c new file +5 -0
+	 * addresses.
+	 */
+	if (is_steinhart) {
+		new_custom->offset = st->custom_table_size /
+					LTC2983_CUSTOM_STEINHART_ENTRY_

SZ;

drivers/iio/temperature/ltc2983.c new file +3 -0
+		st->custom_table_size += new_custom->size;
+	} else {
+		/* mark as unset. This is checked later on the assign

phase */

drivers/iio/temperature/ltc2983.c new file +7 -0
+		new_custom->offset = -1;
+	}
+
+	return new_custom;
+}
+
+static int ltc2983_thermocouple_fault_handler(const struct

ltc2983_data *st,

drivers/iio/temperature/ltc2983.c new file +4 -0
+					      const u32 result)
+{
+	return __ltc2983_fault_handler(st, result,
+				       LTC2983_THERMOCOUPLE_HARD_FAULT_

MASK,

drivers/iio/temperature/ltc2983.c new file +1 -0
+				       LTC2983_THERMOCOUPLE_SOFT_FAULT_

MASK);

drivers/iio/temperature/ltc2983.c new file +3 -0
+}
+
+static int ltc2983_common_fault_handler(const struct ltc2983_data

*st,

drivers/iio/temperature/ltc2983.c new file +8 -0
+					const u32 result)
+{
+	return __ltc2983_fault_handler(st, result,
+				       LTC2983_COMMON_HARD_FAULT_MASK,
+				       LTC2983_COMMON_SOFT_FAULT_MASK);
+}
+
+static int ltc2983_thermocouple_assign_chan(struct ltc2983_data

*st,

drivers/iio/temperature/ltc2983.c new file +12 -0
+				const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_thermocouple *thermo = to_thermocouple(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_CHAN_ASSIGN(thermo->cold_junction_chan);
+	chan_val |= LTC2983_THERMOCOUPLE_CFG(thermo->sensor_config);
+
+	if (thermo->custom) {
+		int ret;
+
+		ret = __ltc2983_chan_custom_sensor_assign(st, thermo-
Quoted 1 line

custom,

drivers/iio/temperature/ltc2983.c new file +22 -0
+							  &chan_val);
+		if (ret)
+			return ret;
+	}
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static int ltc2983_rtd_assign_chan(struct ltc2983_data *st,
+				   const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_rtd *rtd = to_rtd(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_CHAN_ASSIGN(rtd->r_sense_chan);
+	chan_val |= LTC2983_RTD_CFG(rtd->sensor_config);
+	chan_val |= LTC2983_RTD_EXC_CURRENT(rtd->excitation_current);
+	chan_val |= LTC2983_RTD_CURVE(rtd->rtd_curve);
+
+	if (rtd->custom) {
+		int ret;
+
+		ret = __ltc2983_chan_custom_sensor_assign(st, rtd-
Quoted 1 line

custom,

drivers/iio/temperature/ltc2983.c new file +9 -0
+							  &chan_val);
+		if (ret)
+			return ret;
+	}
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static int ltc2983_thermistor_assign_chan(struct ltc2983_data *st,
+					  const struct ltc2983_sensor

*sensor)

drivers/iio/temperature/ltc2983.c new file +8 -0
+{
+	struct ltc2983_thermistor *thermistor = to_thermistor(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_CHAN_ASSIGN(thermistor->r_sense_chan);
+	chan_val |= LTC2983_THERMISTOR_CFG(thermistor->sensor_config);
+	chan_val |=
+		LTC2983_THERMISTOR_EXC_CURRENT(thermistor-
Quoted 1 line

excitation_current);

drivers/iio/temperature/ltc2983.c new file +6 -0
+
+	if (thermistor->custom) {
+		int ret;
+
+		ret = __ltc2983_chan_custom_sensor_assign(st,
+							  thermistor-
Quoted 1 line

custom,

drivers/iio/temperature/ltc2983.c new file +9 -0
+							  &chan_val);
+		if (ret)
+			return ret;
+	}
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static int ltc2983_diode_assign_chan(struct ltc2983_data *st,
+				     const struct ltc2983_sensor

*sensor)

drivers/iio/temperature/ltc2983.c new file +6 -0
+{
+	struct ltc2983_diode *diode = to_diode(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_DIODE_CFG(diode->sensor_config);
+	chan_val |= LTC2983_DIODE_EXC_CURRENT(diode-
Quoted 1 line

excitation_current);

drivers/iio/temperature/ltc2983.c new file +1 -0
+	chan_val |= LTC2983_DIODE_IDEAL_FACTOR(diode-
Quoted 1 line

ideal_factor_value);

drivers/iio/temperature/ltc2983.c new file +6 -0
+
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static int ltc2983_r_sense_assign_chan(struct ltc2983_data *st,
+				       const struct ltc2983_sensor

*sensor)

drivers/iio/temperature/ltc2983.c new file +22 -0
+{
+	struct ltc2983_rsense *rsense = to_rsense(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_R_SENSE_VAL(rsense->r_sense_val);
+
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static int ltc2983_adc_assign_chan(struct ltc2983_data *st,
+				   const struct ltc2983_sensor *sensor)
+{
+	struct ltc2983_adc *adc = to_adc(sensor);
+	u32 chan_val;
+
+	chan_val = LTC2983_ADC_SINGLE_ENDED(adc->single_ended);
+
+	return __ltc2983_chan_assign_common(st, sensor, chan_val);
+}
+
+static struct ltc2983_sensor *ltc2983_thermocouple_new(
+					const struct device_node

*child,

drivers/iio/temperature/ltc2983.c new file +2 -0
+					struct ltc2983_data *st,
+					const struct ltc2983_sensor

*sensor)

drivers/iio/temperature/ltc2983.c new file +5 -0
+{
+	struct ltc2983_thermocouple *thermo;
+	struct device_node *phandle;
+
+	thermo = devm_kzalloc(&st->spi->dev, sizeof(*thermo),

GFP_KERNEL);

drivers/iio/temperature/ltc2983.c new file +7 -0
+	if (!thermo)
+		return ERR_PTR(-ENOMEM);
+
+	of_property_read_u32(child, "adi,sensor-config",
+				 &thermo->sensor_config);
+	/* validate channel index */
+	if (!(thermo->sensor_config & LTC2983_THERMOCOUPLE_DIFF_MASK)

&&

drivers/iio/temperature/ltc2983.c new file +3 -0
+	    sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+		dev_err(&st->spi->dev,
+			"Invalid chann:%d for differential

thermocouple",

drivers/iio/temperature/ltc2983.c new file +1 -0
+								sensor-
Quoted 1 line

chan);

drivers/iio/temperature/ltc2983.c new file +4 -0
+		return ERR_PTR(-EINVAL);
+	}
+
+	phandle = of_parse_phandle(child, "adi,cold-junction-handle",

0);

drivers/iio/temperature/ltc2983.c new file +5 -0
+	if (phandle) {
+		int ret;
+
+		ret = of_property_read_u32(phandle, "reg",
+					   &thermo-
Quoted 1 line

cold_junction_chan);

drivers/iio/temperature/ltc2983.c new file +3 -0
+		if (ret) {
+			/*
+			 * This would be catched later but we can just

return

drivers/iio/temperature/ltc2983.c new file +3 -0
+			 * the error right away.
+			 */
+			dev_err(&st->spi->dev, "Property reg must be

given\n");

drivers/iio/temperature/ltc2983.c new file +8 -0
+			of_node_put(phandle);
+			return ERR_PTR(-EINVAL);
+		}
+	}
+
+	/* check custom sensor */
+	if (sensor->type == LTC2983_SENSOR_THERMOCOUPLE_CUSTOM) {
+		thermo->custom = __ltc2983_custom_sensor_new(st, child,

false,

drivers/iio/temperature/ltc2983.c new file +1 -0
+							     16384,

true);

drivers/iio/temperature/ltc2983.c new file +8 -0
+		if (IS_ERR(thermo->custom)) {
+			of_node_put(phandle);
+			return ERR_CAST(thermo->custom);
+		}
+	}
+
+	/* set common parameters */
+	thermo->sensor.fault_handler =

ltc2983_thermocouple_fault_handler;

drivers/iio/temperature/ltc2983.c new file +7 -0
+	thermo->sensor.assign_chan = ltc2983_thermocouple_assign_chan;
+
+	of_node_put(phandle);
+	return &thermo->sensor;
+}
+
+static struct ltc2983_sensor *ltc2983_rtd_new(const struct

device_node *child,

drivers/iio/temperature/ltc2983.c new file +2 -0
+					  struct ltc2983_data *st,
+					  const struct ltc2983_sensor

*sensor)

drivers/iio/temperature/ltc2983.c new file +14 -0
+{
+	struct ltc2983_rtd *rtd;
+	int ret = 0;
+	struct device *dev = &st->spi->dev;
+	struct device_node *phandle;
+	u32 excitation_current = 0;
+
+	rtd = devm_kzalloc(dev, sizeof(*rtd), GFP_KERNEL);
+	if (!rtd)
+		return ERR_PTR(-ENOMEM);
+
+	phandle = of_parse_phandle(child, "adi,rsense-handle", 0);
+	if (!phandle) {
+		dev_err(dev, "Property adi,rsense-handle missing or

invalid");

drivers/iio/temperature/ltc2983.c new file +10 -0
+		return ERR_PTR(-EINVAL);
+	}
+
+	ret = of_property_read_u32(phandle, "reg", &rtd->r_sense_chan);
+	if (ret) {
+		dev_err(dev, "Property reg must be given\n");
+		goto fail;
+	}
+
+	of_property_read_u32(child, "adi,sensor-config", &rtd-
Quoted 1 line

sensor_config);

drivers/iio/temperature/ltc2983.c new file +5 -0
+	/*
+	 * rtd channel indexes are a bit more complicated to validate.
+	 * For 4wire RTD with rotation, the channel selection cannot be
+	 * >=19 since the chann + 1 is used in this configuration.
+	 * For 4wire RTDs with kelvin rsense, the rsense channel cannot

be

drivers/iio/temperature/ltc2983.c new file +11 -0
+	 * <=1 since chanel - 1 and channel - 2 are used.
+	 */
+	if (rtd->sensor_config & LTC2983_RTD_4_WIRE_MASK) {
+		/* 4-wire */
+		u8 min = LTC2983_DIFFERENTIAL_CHAN_MIN,
+			max = LTC2983_MAX_CHANNELS_NR;
+
+		if (rtd->sensor_config & LTC2983_RTD_ROTATION_MASK)
+			max = LTC2983_MAX_CHANNELS_NR - 1;
+
+		if (((rtd->sensor_config &

LTC2983_RTD_KELVIN_R_SENSE_MASK)

drivers/iio/temperature/ltc2983.c new file +5 -0
+		     == LTC2983_RTD_KELVIN_R_SENSE_MASK) &&
+		    (rtd->r_sense_chan <=  min)) {
+			/* kelvin rsense*/
+			dev_err(dev,
+				"Invalid rsense chann:%d to use in

kelvin rsense",

drivers/iio/temperature/ltc2983.c new file +1 -0
+							rtd-
Quoted 1 line

r_sense_chan);

drivers/iio/temperature/ltc2983.c new file +7 -0
+
+			ret = -EINVAL;
+			goto fail;
+		}
+
+		if (sensor->chan < min || sensor->chan > max) {
+			dev_err(dev, "Invalid chann:%d for the rtd

config",

drivers/iio/temperature/ltc2983.c new file +1 -0
+								sensor-
Quoted 1 line

chan);

drivers/iio/temperature/ltc2983.c new file +9 -0
+
+			ret = -EINVAL;
+			goto fail;
+		}
+	} else {
+		/* same as differential case */
+		if (sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+			dev_err(&st->spi->dev,
+				"Invalid chann:%d for RTD", sensor-
Quoted 1 line

chan);

drivers/iio/temperature/ltc2983.c new file +9 -0
+
+			ret = -EINVAL;
+			goto fail;
+		}
+	}
+
+	/* check custom sensor */
+	if (sensor->type == LTC2983_SENSOR_RTD_CUSTOM) {
+		rtd->custom = __ltc2983_custom_sensor_new(st, child,

false,

drivers/iio/temperature/ltc2983.c new file +12 -0
+							  2048, false);
+		if (IS_ERR(rtd->custom)) {
+			of_node_put(phandle);
+			return ERR_CAST(rtd->custom);
+		}
+	}
+
+	/* set common parameters */
+	rtd->sensor.fault_handler = ltc2983_common_fault_handler;
+	rtd->sensor.assign_chan = ltc2983_rtd_assign_chan;
+
+	ret = of_property_read_u32(child, "adi,excitation-current-

microamp",

drivers/iio/temperature/ltc2983.c new file +33 -0
+				   &excitation_current);
+	if (ret) {
+		/* default to 5uA */
+		rtd->excitation_current = 1;
+	} else {
+		switch (excitation_current) {
+		case 5:
+			rtd->excitation_current = 0x01;
+			break;
+		case 10:
+			rtd->excitation_current = 0x02;
+			break;
+		case 25:
+			rtd->excitation_current = 0x03;
+			break;
+		case 50:
+			rtd->excitation_current = 0x04;
+			break;
+		case 100:
+			rtd->excitation_current = 0x05;
+			break;
+		case 250:
+			rtd->excitation_current = 0x06;
+			break;
+		case 500:
+			rtd->excitation_current = 0x07;
+			break;
+		case 1000:
+			rtd->excitation_current = 0x08;
+			break;
+		default:
+			dev_err(&st->spi->dev,
+				"Invalid value for excitation

current(%u)",

drivers/iio/temperature/ltc2983.c new file +1 -0
+							excitation_curr

ent);

drivers/iio/temperature/ltc2983.c new file +16 -0
+			ret = -EINVAL;
+			goto fail;
+		}
+	}
+
+	of_property_read_u32(child, "adi,rtd-curve", &rtd->rtd_curve);
+
+	of_node_put(phandle);
+	return &rtd->sensor;
+fail:
+	of_node_put(phandle);
+	return ERR_PTR(ret);
+}
+
+static struct ltc2983_sensor *ltc2983_thermistor_new(
+					const struct device_node

*child,

drivers/iio/temperature/ltc2983.c new file +2 -0
+					struct ltc2983_data *st,
+					const struct ltc2983_sensor

*sensor)

drivers/iio/temperature/ltc2983.c new file +8 -0
+{
+	struct ltc2983_thermistor *thermistor;
+	struct device *dev = &st->spi->dev;
+	struct device_node *phandle;
+	u32 excitation_current = 0;
+	int ret = 0;
+
+	thermistor = devm_kzalloc(dev, sizeof(*thermistor),

GFP_KERNEL);

drivers/iio/temperature/ltc2983.c new file +6 -0
+	if (!thermistor)
+		return ERR_PTR(-ENOMEM);
+
+	phandle = of_parse_phandle(child, "adi,rsense-handle", 0);
+	if (!phandle) {
+		dev_err(dev, "Property adi,rsense-handle missing or

invalid");

drivers/iio/temperature/ltc2983.c new file +4 -0
+		return ERR_PTR(-EINVAL);
+	}
+
+	ret = of_property_read_u32(phandle, "reg", &thermistor-
Quoted 1 line

r_sense_chan);

drivers/iio/temperature/ltc2983.c new file +9 -0
+	if (ret) {
+		dev_err(dev, "rsense channel must be configured...\n");
+		goto fail;
+	}
+
+	of_property_read_u32(child, "adi,sensor-config",
+			     &thermistor->sensor_config);
+	/* validate channel index */
+	if (!(thermistor->sensor_config & LTC2983_THERMISTOR_DIFF_MASK)

&&

drivers/iio/temperature/ltc2983.c new file +4 -0
+	    sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+		dev_err(&st->spi->dev,
+			"Invalid chann:%d for differential thermistor",
+								sensor-
Quoted 1 line

chan);

drivers/iio/temperature/ltc2983.c new file +7 -0
+		ret = -EINVAL;
+		goto fail;
+	}
+
+	/* check custom sensor */
+	if (sensor->type >= LTC2983_SENSOR_THERMISTOR_STEINHART) {
+		thermistor->custom = __ltc2983_custom_sensor_new(st,

child,

drivers/iio/temperature/ltc2983.c new file +1 -0
+			sensor->type ==

LTC2983_SENSOR_THERMISTOR_STEINHART ?

drivers/iio/temperature/ltc2983.c new file +1 -0
+							  true : false,

64,

drivers/iio/temperature/ltc2983.c new file +8 -0
+							  false);
+		if (IS_ERR(thermistor->custom)) {
+			of_node_put(phandle);
+			return ERR_CAST(thermistor->custom);
+		}
+	}
+	/* set common parameters */
+	thermistor->sensor.fault_handler =

ltc2983_common_fault_handler;

drivers/iio/temperature/ltc2983.c new file +1 -0
+	thermistor->sensor.assign_chan =

ltc2983_thermistor_assign_chan;

drivers/iio/temperature/ltc2983.c new file +2 -0
+
+	ret = of_property_read_u32(child, "adi,excitation-current-

nanoamp",

drivers/iio/temperature/ltc2983.c new file +4 -0
+				   &excitation_current);
+	if (ret) {
+		/* Auto range is not allowed for custom sensors */
+		if (sensor->type >=

LTC2983_SENSOR_THERMISTOR_STEINHART)

drivers/iio/temperature/ltc2983.c new file +13 -0
+			/* default to 1uA */
+			thermistor->excitation_current = 0x03;
+		else
+			/* default to auto-range */
+			thermistor->excitation_current = 0x0c;
+	} else {
+		switch (excitation_current) {
+		case 0:
+			/* auto range */
+			if (sensor->type >=
+			    LTC2983_SENSOR_THERMISTOR_STEINHART) {
+				dev_err(&st->spi->dev,
+					"Auto Range not allowed for

custom sensors\n");

drivers/iio/temperature/ltc2983.c new file +41 -0
+				ret = -EINVAL;
+				goto fail;
+			}
+			thermistor->excitation_current = 0x0c;
+			break;
+		case 250:
+			thermistor->excitation_current = 0x01;
+			break;
+		case 500:
+			thermistor->excitation_current = 0x02;
+			break;
+		case 1000:
+			thermistor->excitation_current = 0x03;
+			break;
+		case 5000:
+			thermistor->excitation_current = 0x04;
+			break;
+		case 10000:
+			thermistor->excitation_current = 0x05;
+			break;
+		case 25000:
+			thermistor->excitation_current = 0x06;
+			break;
+		case 50000:
+			thermistor->excitation_current = 0x07;
+			break;
+		case 100000:
+			thermistor->excitation_current = 0x08;
+			break;
+		case 250000:
+			thermistor->excitation_current = 0x09;
+			break;
+		case 500000:
+			thermistor->excitation_current = 0x0a;
+			break;
+		case 1000000:
+			thermistor->excitation_current = 0x0b;
+			break;
+		default:
+			dev_err(&st->spi->dev,
+				"Invalid value for excitation

current(%u)",

drivers/iio/temperature/ltc2983.c new file +1 -0
+							excitation_curr

ent);

drivers/iio/temperature/ltc2983.c new file +14 -0
+			ret = -EINVAL;
+			goto fail;
+		}
+	}
+
+	of_node_put(phandle);
+	return &thermistor->sensor;
+fail:
+	of_node_put(phandle);
+	return ERR_PTR(ret);
+}
+
+static struct ltc2983_sensor *ltc2983_diode_new(
+					const struct device_node

*child,

drivers/iio/temperature/ltc2983.c new file +2 -0
+					const struct ltc2983_data *st,
+					const struct ltc2983_sensor

*sensor)

drivers/iio/temperature/ltc2983.c new file +6 -0
+{
+	struct ltc2983_diode *diode;
+	u32 temp = 0, excitation_current = 0;
+	int ret;
+
+	diode = devm_kzalloc(&st->spi->dev, sizeof(*diode),

GFP_KERNEL);

drivers/iio/temperature/ltc2983.c new file +4 -0
+	if (!diode)
+		return ERR_PTR(-ENOMEM);
+
+	of_property_read_u32(child, "adi,sensor-config", &diode-
Quoted 1 line

sensor_config);

drivers/iio/temperature/ltc2983.c new file +6 -0
+	/* validate channel index */
+	if (!(diode->sensor_config & LTC2983_DIODE_DIFF_MASK) &&
+	    sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+		dev_err(&st->spi->dev,
+			"Invalid chann:%d for differential thermistor",
+								sensor-
Quoted 1 line

chan);

drivers/iio/temperature/ltc2983.c new file +7 -0
+		return ERR_PTR(-EINVAL);
+	}
+	/* set common parameters */
+	diode->sensor.fault_handler = ltc2983_common_fault_handler;
+	diode->sensor.assign_chan = ltc2983_diode_assign_chan;
+
+	ret = of_property_read_u32(child, "adi,excitation-current-

microamp",

drivers/iio/temperature/ltc2983.c new file +18 -0
+				   &excitation_current);
+	if (!ret) {
+		switch (excitation_current) {
+		case 10:
+			diode->excitation_current = 0x00;
+			break;
+		case 20:
+			diode->excitation_current = 0x01;
+			break;
+		case 40:
+			diode->excitation_current = 0x02;
+			break;
+		case 80:
+			diode->excitation_current = 0x03;
+			break;
+		default:
+			dev_err(&st->spi->dev,
+				"Invalid value for excitation

current(%u)",

drivers/iio/temperature/ltc2983.c new file +1 -0
+							excitation_curr

ent);

drivers/iio/temperature/ltc2983.c new file +13 -0
+			return ERR_PTR(-EINVAL);
+		}
+	}
+
+	of_property_read_u32(child, "adi,ideal-factor-value", &temp);
+
+	/* 2^20 resolution */
+	diode->ideal_factor_value = __convert_to_raw(temp, 1048576);
+
+	return &diode->sensor;
+}
+
+static struct ltc2983_sensor *ltc2983_r_sense_new(struct

device_node *child,

drivers/iio/temperature/ltc2983.c new file +2 -0
+					struct ltc2983_data *st,
+					const struct ltc2983_sensor

*sensor)

drivers/iio/temperature/ltc2983.c new file +6 -0
+{
+	struct ltc2983_rsense *rsense;
+	int ret;
+	u64 temp;
+
+	rsense = devm_kzalloc(&st->spi->dev, sizeof(*rsense),

GFP_KERNEL);

drivers/iio/temperature/ltc2983.c new file +11 -0
+	if (!rsense)
+		return ERR_PTR(-ENOMEM);
+
+	/* validate channel index */
+	if (sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+		dev_err(&st->spi->dev, "Invalid chann:%d for r_sense",
+							sensor->chan);
+		return ERR_PTR(-EINVAL);
+	}
+	/* get raw value */
+	ret = of_property_read_u64(child, "adi,rsense-val-micro-ohms",

&temp);

drivers/iio/temperature/ltc2983.c new file +2 -0
+	if (ret) {
+		dev_err(&st->spi->dev, "Property adi,rsense-val-micro-

ohms missing\n");

drivers/iio/temperature/ltc2983.c new file +13 -0
+		return ERR_PTR(-EINVAL);
+	}
+
+	/* 2^10 resolution */
+	rsense->r_sense_val = __convert_to_raw(temp, 1024);
+
+	/* set common parameters */
+	rsense->sensor.assign_chan = ltc2983_r_sense_assign_chan;
+
+	return &rsense->sensor;
+}
+
+static struct ltc2983_sensor *ltc2983_adc_new(struct device_node

*child,

drivers/iio/temperature/ltc2983.c new file +2 -0
+					 struct ltc2983_data *st,
+					 const struct ltc2983_sensor

*sensor)

drivers/iio/temperature/ltc2983.c new file +13 -0
+{
+	struct ltc2983_adc *adc;
+
+	adc = devm_kzalloc(&st->spi->dev, sizeof(*adc), GFP_KERNEL);
+	if (!adc)
+		return ERR_PTR(-ENOMEM);
+
+	if (of_property_read_bool(child, "adi,single-ended"))
+		adc->single_ended = true;
+
+	if (!adc->single_ended &&
+	    sensor->chan < LTC2983_DIFFERENTIAL_CHAN_MIN) {
+		dev_err(&st->spi->dev, "Invalid chan:%d for

differential adc\n",

drivers/iio/temperature/ltc2983.c new file +1 -0
+								sensor-
Quoted 1 line

chan);

drivers/iio/temperature/ltc2983.c new file +20 -0
+		return ERR_PTR(-EINVAL);
+	}
+	/* set common parameters */
+	adc->sensor.assign_chan = ltc2983_adc_assign_chan;
+	adc->sensor.fault_handler = ltc2983_common_fault_handler;
+
+	return &adc->sensor;
+}
+
+static int ltc2983_chan_read(struct ltc2983_data *st,
+			const struct ltc2983_sensor *sensor, int *val)
+{
+	u32 start_conversion = 0;
+	int ret;
+	unsigned long time;
+	__be32 temp;
+
+	/*
+	 * Do not allow channel readings if device is in sleep state.
+	 * A read/write on the spi bus would bring the device

prematurely

drivers/iio/temperature/ltc2983.c new file +8 -0
+	 * out of sleep.
+	 */
+	if (st->sleep)
+		return -EPERM;
+
+	start_conversion = LTC2983_STATUS_START(true);
+	start_conversion |= LTC2983_STATUS_CHAN_SEL(sensor->chan);
+	dev_dbg(&st->spi->dev, "Start conversion on chan:%d,

status:%02X\n",

drivers/iio/temperature/ltc2983.c new file +3 -0
+		sensor->chan, start_conversion);
+	/* start conversion */
+	ret = regmap_write(st->regmap, LTC2983_STATUS_REG,

start_conversion);

drivers/iio/temperature/ltc2983.c new file +7 -0
+	if (ret)
+		return ret;
+
+	reinit_completion(&st->completion);
+	/*
+	 * wait for conversion to complete.
+	 * 300 ms should be more than enough to complete the

conversion.

drivers/iio/temperature/ltc2983.c new file +1 -0
+	 * Depending on the sensor configuration, there are 2/3

conversions

drivers/iio/temperature/ltc2983.c new file +11 -0
+	 * cycles of 82ms.
+	 */
+	time = wait_for_completion_timeout(&st->completion,
+					   msecs_to_jiffies(300));
+	if (!time) {
+		dev_warn(&st->spi->dev, "Conversion timed out\n");
+		return -ETIMEDOUT;
+	}
+
+	/* read the converted data */
+	ret = regmap_bulk_read(st->regmap,

LTC2983_CHAN_RES_ADDR(sensor->chan),

drivers/iio/temperature/ltc2983.c new file +8 -0
+			       &temp, sizeof(temp));
+	if (ret)
+		return ret;
+
+	*val = __be32_to_cpu(temp);
+
+	if (!(LTC2983_RES_VALID_MASK & *val)) {
+		dev_err(&st->spi->dev, "Invalid conversion

detected\n");

drivers/iio/temperature/ltc2983.c new file +8 -0
+		return -EIO;
+	}
+
+	ret = sensor->fault_handler(st, *val);
+	if (ret)
+		return ret;
+
+	*val = sign_extend32((*val) & LTC2983_DATA_MASK,

LTC2983_DATA_SIGN_BIT);

drivers/iio/temperature/ltc2983.c new file +21 -0
+	return 0;
+}
+
+static int ltc2983_read_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int *val, int *val2, long mask)
+{
+	struct ltc2983_data *st = iio_priv(indio_dev);
+	int ret;
+
+	/* sanity check */
+	if (chan->address >= st->num_channels) {
+		dev_err(&st->spi->dev, "Invalid chan address:%ld",
+							chan->address);
+		return -EINVAL;
+	}
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		mutex_lock(&st->lock);
+		ret = ltc2983_chan_read(st, st->sensors[chan->address], 

val);

drivers/iio/temperature/ltc2983.c new file +36 -0
+		mutex_unlock(&st->lock);
+		return ret ?: IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_TEMP:
+			/* value in milli degrees */
+			*val = 1000;
+			/* 2^10 */
+			*val2 = 1024;
+			return IIO_VAL_FRACTIONAL;
+		case IIO_VOLTAGE:
+			/* value in millivolt */
+			*val = 1000;
+			/* 2^21 */
+			*val2 = 2097152;
+			return IIO_VAL_FRACTIONAL;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return -EINVAL;
+}
+
+static int ltc2983_reg_access(struct iio_dev *indio_dev,
+			      unsigned int reg,
+			      unsigned int writeval,
+			      unsigned int *readval)
+{
+	struct ltc2983_data *st = iio_priv(indio_dev);
+
+	/* check comment in ltc2983_chan_read() */
+	if (st->sleep)
+		return -EPERM;
+
+	if (readval)

drivers/iio/temperature/ltc2983.c line 1114

Quoted 10 lines
drivers/iio/temperature/ltc2983.c new file +10 -0
+		return regmap_read(st->regmap, reg, readval);
+	else
+		return regmap_write(st->regmap, reg, writeval);
+}
+
+static irqreturn_t ltc2983_irq_handler(int irq, void *data)
+{
+	struct ltc2983_data *st = data;
+
+	complete(&st->completion);

This is a rare case where I'm not sure a threaded irq actually makes sense. We may be better off just doing this in a traditional top half, rather than spinning up a thread just to set completion.

Quoted 362 lines
drivers/iio/temperature/ltc2983.c new file +22 -0
+	return IRQ_HANDLED;
+}
+
+#define LTC2983_CHAN(__type, index, __address) ({ \
+	struct iio_chan_spec __chan = { \
+		.type = __type, \
+		.indexed = 1, \
+		.channel = index, \
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
+		.address = __address, \
+	}; \
+	__chan; \
+})
+
+static int ltc2983_parse_dt(struct ltc2983_data *st)
+{
+	struct device_node *child;
+	struct device *dev = &st->spi->dev;
+	int ret = 0, chan = 0, channel_avail_mask = 0;
+
+	if (!of_property_read_bool(dev->of_node, "adi,temperature-

celcius"))

drivers/iio/temperature/ltc2983.c new file +10 -0
+		st->temp_farenheit = true;
+
+	of_property_read_u32(dev->of_node, "adi,mux-delay-config-us",
+			     &st->mux_delay_config);
+
+	of_property_read_u32(dev->of_node, "adi,filter-notch-freq",
+			     &st->filter_notch_freq);
+
+	st->num_channels = of_get_available_child_count(dev->of_node);
+	st->sensors = devm_kcalloc(dev, st->num_channels, sizeof(*st-
Quoted 1 line

sensors),

drivers/iio/temperature/ltc2983.c new file +11 -0
+				   GFP_KERNEL);
+	if (!st->sensors)
+		return -ENOMEM;
+
+	st->iio_channels = st->num_channels;
+	for_each_available_child_of_node(dev->of_node, child) {
+		struct ltc2983_sensor sensor;
+
+		ret = of_property_read_u32(child, "reg", &sensor.chan);
+		if (ret) {
+			dev_err(dev, "reg property must given for child

nodes\n");

drivers/iio/temperature/ltc2983.c new file +8 -0
+			return ret;
+		}
+
+		/* check if we have a valid channel */
+		if (sensor.chan < LTC2983_MIN_CHANNELS_NR ||
+		    sensor.chan > LTC2983_MAX_CHANNELS_NR) {
+			dev_err(dev,
+				"chan:%d must be from 1 to 20\n",

sensor.chan);

drivers/iio/temperature/ltc2983.c new file +3 -0
+			return -EINVAL;
+		} else if (channel_avail_mask & BIT(sensor.chan)) {
+			dev_err(dev, "chan:%d already in use\n",

sensor.chan);

drivers/iio/temperature/ltc2983.c new file +8 -0
+			return -EINVAL;
+		}
+
+		ret = of_property_read_u32(child, "adi,sensor-type",
+					       &sensor.type);
+		if (ret) {
+			dev_err(dev,
+				"adi,sensor-type property must given

for child nodes\n");

drivers/iio/temperature/ltc2983.c new file +5 -0
+			return ret;
+		}
+
+		dev_dbg(dev, "Create new sensor, type %u, chann %u",
+								sensor.

type,

drivers/iio/temperature/ltc2983.c new file +1 -0
+								sensor.

chan);

drivers/iio/temperature/ltc2983.c new file +3 -0
+
+		if (sensor.type >= LTC2983_SENSOR_THERMOCOUPLE &&
+		    sensor.type <= LTC2983_SENSOR_THERMOCOUPLE_CUSTOM)

{

drivers/iio/temperature/ltc2983.c new file +1 -0
+			st->sensors[chan] =

ltc2983_thermocouple_new(child, st,

drivers/iio/temperature/ltc2983.c new file +1 -0
+								     &s

ensor);

drivers/iio/temperature/ltc2983.c new file +3 -0
+		} else if (sensor.type >= LTC2983_SENSOR_RTD &&
+			   sensor.type <= LTC2983_SENSOR_RTD_CUSTOM) {
+			st->sensors[chan] = ltc2983_rtd_new(child, st,

&sensor);

drivers/iio/temperature/ltc2983.c new file +2 -0
+		} else if (sensor.type >= LTC2983_SENSOR_THERMISTOR &&
+			   sensor.type <=

LTC2983_SENSOR_THERMISTOR_CUSTOM) {

drivers/iio/temperature/ltc2983.c new file +1 -0
+			st->sensors[chan] =

ltc2983_thermistor_new(child, st,

drivers/iio/temperature/ltc2983.c new file +1 -0
+								   &sen

sor);

drivers/iio/temperature/ltc2983.c new file +2 -0
+		} else if (sensor.type == LTC2983_SENSOR_DIODE) {
+			st->sensors[chan] = ltc2983_diode_new(child,

st,

drivers/iio/temperature/ltc2983.c new file +2 -0
+							      &sensor);
+		} else if (sensor.type ==

LTC2983_SENSOR_SENSE_RESISTOR) {

drivers/iio/temperature/ltc2983.c new file +1 -0
+			st->sensors[chan] = ltc2983_r_sense_new(child,

st,

drivers/iio/temperature/ltc2983.c new file +1 -0
+								&sensor

);

drivers/iio/temperature/ltc2983.c new file +4 -0
+			/* don't add rsense to iio */
+			st->iio_channels--;
+		} else if (sensor.type == LTC2983_SENSOR_DIRECT_ADC) {
+			st->sensors[chan] = ltc2983_adc_new(child, st,

&sensor);

drivers/iio/temperature/ltc2983.c new file +2 -0
+		} else {
+			dev_err(dev, "Unknown sensor type %d\n",

sensor.type);

drivers/iio/temperature/ltc2983.c new file +6 -0
+			return -EINVAL;
+		}
+
+		if (IS_ERR(st->sensors[chan])) {
+			dev_err(dev, "Failed to create sensor %ld",
+						PTR_ERR(st-
Quoted 1 line

sensors[chan]));

drivers/iio/temperature/ltc2983.c new file +31 -0
+			return PTR_ERR(st->sensors[chan]);
+		}
+		/* set generic sensor parameters */
+		st->sensors[chan]->chan = sensor.chan;
+		st->sensors[chan]->type = sensor.type;
+
+		channel_avail_mask |= BIT(sensor.chan);
+		chan++;
+	}
+
+	return 0;
+}
+
+static int ltc2983_setup(struct ltc2983_data *st, bool assign_iio)
+{
+	u32 iio_chan_t = 0, iio_chan_v = 0, chan, iio_idx = 0;
+	u32 global_cfg = 0;
+	int ret;
+	unsigned long time;
+
+	/* make sure the device is up */
+	time = wait_for_completion_timeout(&st->completion,
+					    msecs_to_jiffies(250));
+
+	if (!time) {
+		dev_err(&st->spi->dev, "Device startup timed out\n");
+		return -ETIMEDOUT;
+	}
+
+	st->iio_chan = devm_kzalloc(&st->spi->dev,
+				    st->iio_channels * sizeof(*st-
Quoted 1 line

iio_chan),

drivers/iio/temperature/ltc2983.c new file +8 -0
+				    GFP_KERNEL);
+
+	if (!st->iio_chan)
+		return -ENOMEM;
+
+	global_cfg = LTC2983_NOTCH_FREQ(st->filter_notch_freq);
+	global_cfg |= LTC2983_TEMP_UNITS(st->temp_farenheit);
+	regmap_write(st->regmap, LTC2983_GLOBAL_CONFIG_REG,

global_cfg);

drivers/iio/temperature/ltc2983.c new file +1 -0
+	regmap_write(st->regmap, LTC2983_MUX_CONFIG_REG, st-
Quoted 1 line

mux_delay_config);

drivers/iio/temperature/ltc2983.c new file +5 -0
+
+	for (chan = 0; chan < st->num_channels; chan++) {
+		u32 chan_type = 0, *iio_chan;
+
+		ret = st->sensors[chan]->assign_chan(st, st-
Quoted 1 line

sensors[chan]);

drivers/iio/temperature/ltc2983.c new file +4 -0
+		if (ret)
+			return ret;
+		/*
+		 * The assign_iio flag is necessary for when the device

is

drivers/iio/temperature/ltc2983.c new file +5 -0
+		 * coming out of sleep. In that case, we just need to
+		 * re-configure the device channels.
+		 * We also don't assign iio channels for rsense.
+		 */
+		if (st->sensors[chan]->type ==

LTC2983_SENSOR_SENSE_RESISTOR ||

drivers/iio/temperature/ltc2983.c new file +5 -0
+		    !assign_iio)
+			continue;
+
+		/* assign iio channel */
+		if (st->sensors[chan]->type !=

LTC2983_SENSOR_DIRECT_ADC) {

drivers/iio/temperature/ltc2983.c new file +9 -0
+			chan_type = IIO_TEMP;
+			iio_chan = &iio_chan_t;
+		} else {
+			chan_type = IIO_VOLTAGE;
+			iio_chan = &iio_chan_v;
+		}
+
+		/*
+		 * add chan as the iio .address so that, we can

directly

drivers/iio/temperature/ltc2983.c new file +3 -0
+		 * reference the sensor given the iio_chan_spec
+		 */
+		st->iio_chan[iio_idx++] = LTC2983_CHAN(chan_type,

(*iio_chan)++,

drivers/iio/temperature/ltc2983.c new file +9 -0
+						       chan);
+	}
+
+	return 0;
+}
+
+static const struct regmap_range ltc2983_reg_ranges[] = {
+	regmap_reg_range(LTC2983_STATUS_REG, LTC2983_STATUS_REG),
+	regmap_reg_range(LTC2983_TEMP_RES_START_REG,

LTC2983_TEMP_RES_END_REG),

drivers/iio/temperature/ltc2983.c new file +1 -0
+	regmap_reg_range(LTC2983_GLOBAL_CONFIG_REG,

LTC2983_GLOBAL_CONFIG_REG),

drivers/iio/temperature/ltc2983.c new file +3 -0
+	regmap_reg_range(LTC2983_MULT_CHANNEL_START_REG,
+			 LTC2983_MULT_CHANNEL_END_REG),
+	regmap_reg_range(LTC2983_MUX_CONFIG_REG,

LTC2983_MUX_CONFIG_REG),

drivers/iio/temperature/ltc2983.c new file +13 -0
+	regmap_reg_range(LTC2983_CHAN_ASSIGN_START_REG,
+			 LTC2983_CHAN_ASSIGN_END_REG),
+	regmap_reg_range(LTC2983_CUST_SENS_TBL_START_REG,
+			 LTC2983_CUST_SENS_TBL_END_REG),
+};
+
+static const struct regmap_access_table ltc2983_reg_table = {
+	.yes_ranges = ltc2983_reg_ranges,
+	.n_yes_ranges = ARRAY_SIZE(ltc2983_reg_ranges),
+};
+
+/*
+ *  The reg_bits are actually 12 but the device needs the first

*complete*
+ * byte for the command (R/W).
+ */

drivers/iio/temperature/ltc2983.c new file +47 -0
+static const struct regmap_config ltc2983_regmap_config = {
+	.reg_bits = 24,
+	.val_bits = 8,
+	.wr_table = &ltc2983_reg_table,
+	.rd_table = &ltc2983_reg_table,
+	.read_flag_mask = GENMASK(1, 0),
+	.write_flag_mask = BIT(1),
+};
+
+static const struct  iio_info ltc2983_iio_info = {
+	.read_raw = ltc2983_read_raw,
+	.debugfs_reg_access = ltc2983_reg_access,
+};
+
+static int ltc2983_probe(struct spi_device *spi)
+{
+	struct ltc2983_data *st;
+	struct iio_dev *indio_dev;
+	const char *name = spi_get_device_id(spi)->name;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	st = iio_priv(indio_dev);
+
+	st->regmap = devm_regmap_init_spi(spi, &ltc2983_regmap_config);
+	if (IS_ERR(st->regmap)) {
+		dev_err(&spi->dev, "Failed to initialize regmap\n");
+		return PTR_ERR(st->regmap);
+	}
+
+	mutex_init(&st->lock);
+	init_completion(&st->completion);
+	st->spi = spi;
+	spi_set_drvdata(spi, st);
+
+	ret = ltc2983_parse_dt(st);
+	if (ret)
+		return ret;
+	/*
+	 * let's request the irq now so it is used to sync the device
+	 * startup in ltc2983_setup()
+	 */
+	ret = devm_request_threaded_irq(&spi->dev, spi->irq, NULL,
+					ltc2983_irq_handler,

IRQF_ONESHOT |

drivers/iio/temperature/ltc2983.c new file +3 -0
+					IRQF_TRIGGER_RISING, name, st);
+	if (ret) {
+		dev_err(&spi->dev, "failed to request an irq, %d",

ret);

drivers/iio/temperature/ltc2983.c new file +40 -0
+		return ret;
+	}
+
+	ret = ltc2983_setup(st, true);
+	if (ret)
+		return ret;
+
+	indio_dev->dev.parent = &spi->dev;
+	indio_dev->name = name;
+	indio_dev->num_channels = st->iio_channels;
+	indio_dev->channels = st->iio_chan;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &ltc2983_iio_info;
+
+	return devm_iio_device_register(&spi->dev, indio_dev);
+}
+
+static int __maybe_unused ltc2983_resume(struct device *dev)
+{
+	struct ltc2983_data *st = spi_get_drvdata(to_spi_device(dev));
+	int ret;
+
+	mutex_lock(&st->lock);
+	/* dummy read to bring the device out of sleep */
+	regmap_read(st->regmap, LTC2983_STATUS_REG, &ret);
+	/* we need to re-assign the channels */
+	ret = ltc2983_setup(st, false);
+	st->sleep = false;
+	mutex_unlock(&st->lock);
+
+	return ret;
+}
+
+static int __maybe_unused ltc2983_suspend(struct device *dev)
+{
+	struct ltc2983_data *st = spi_get_drvdata(to_spi_device(dev));
+	int ret;
+
+	mutex_lock(&st->lock);
+	ret = regmap_write(st->regmap, LTC2983_STATUS_REG,

LTC2983_SLEEP);

drivers/iio/temperature/ltc2983.c new file +7 -0
+	st->sleep = true;
+	mutex_unlock(&st->lock);
+
+	return ret;
+}
+
+static SIMPLE_DEV_PM_OPS(ltc2983_pm_ops, ltc2983_suspend,

ltc2983_resume);

drivers/iio/temperature/ltc2983.c new file +27 -0
+
+static const struct spi_device_id ltc2983_id_table[] = {
+	{ "ltc2983" },
+	{},
+};
+MODULE_DEVICE_TABLE(spi, ltc2983_id_table);
+
+static const struct of_device_id ltc2983_of_match[] = {
+	{ .compatible = "adi,ltc2983" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ltc2983_id_table);
+
+static struct spi_driver ltc2983_driver = {
+	.driver = {
+		.name = "ltc2983",
+		.of_match_table = ltc2983_of_match,
+		.pm = &ltc2983_pm_ops,
+	},
+	.probe = ltc2983_probe,
+	.id_table = ltc2983_id_table,
+};
+
+module_spi_driver(ltc2983_driver);
+
+MODULE_AUTHOR("Nuno Sa <[email protected]>");
+MODULE_DESCRIPTION("Analog Devices LTC2983 SPI Temperature

sensors");
+MODULE_LICENSE("GPL");

Signature · 4 lines
Analog Devices GmbH      Otl-Aicher Strasse 60-64      80807 München
Sitz der Gesellschaft München, Registergericht München HRB 40368,
Geschäftsführer: Stefan Steyerl, Thomas Edward Cribben, Michael Paul
Sondel