ARM: dts: imx7d: Correct speed grading fuse settings
Subsystems (2)
PATCH 1/2 ARM: dts: imx7d: Correct speed grading fuse settings
The 800MHz opp speed grading fuse mask should be 0xd instead of 0xf according to fuse map definition:
SPEED_GRADING[1:0] MHz
00 800 01 500 10 1000 11 1200
--- arch/arm/boot/dts/imx7d.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/imx7d.dtsi +1 -1
@@ -43,7 +43,7 @@ opp-hz = /bits/ 64 <792000000>; opp-microvolt = <1000000>; clock-latency-ns = <150000>; - opp-supported-hw = <0xf>, <0xf>; + opp-supported-hw = <0xd>, <0xf>; }; opp-996000000 {
Signature · 1 line
2.7.4
PATCH 2/2 ARM: dts: imx7d: Add opp-suspend property
Add "opp-suspend" property for i.MX7D to make sure system suspend with max available opp.
--- arch/arm/boot/dts/imx7d.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/imx7d.dtsi +3 -0
@@ -44,6 +44,7 @@ opp-microvolt = <1000000>; clock-latency-ns = <150000>; opp-supported-hw = <0xd>, <0xf>; + opp-suspend; }; opp-996000000 {
@@ -51,6 +52,7 @@ opp-microvolt = <1100000>; clock-latency-ns = <150000>; opp-supported-hw = <0xc>, <0xf>; + opp-suspend; }; opp-1200000000 {
@@ -58,6 +60,7 @@ opp-microvolt = <1225000>; clock-latency-ns = <150000>; opp-supported-hw = <0x8>, <0xf>; + opp-suspend; }; };
Signature · 1 line
2.7.4
Re: [PATCH 2/2] ARM: dts: imx7d: Add opp-suspend property
Quoted 4 lines · Anson Huang
Add "opp-suspend" property for i.MX7D to make sure system suspend with max available opp.
Signed-off-by Anson Huang <[email protected]>
Quoted 10 lines · Anson Huang
The 800MHz opp speed grading fuse mask should be
0xdinstead of0xfaccording to fuse map definition:SPEED_GRADING[1:0] MHz
00 800 01 500 10 1000 11 1200Signed-off-by Anson Huang <[email protected]>
Are you going to add the 500mhz OPP as well?
Hi, Leonard
Quoted 10 lines · Anson Huang
Quoted 9 lines
The 800MHz opp speed grading fuse mask should be
0xdinstead of0xfaccording to fuse map definition:SPEED_GRADING[1:0] MHz
00 800 01 500 10 1000 11 1200
Quoted 5 lines
Quoted 1 line
Signed-off-by Anson Huang <[email protected]>Reviewed-by Leonard Crestez <[email protected]>Are you going to add the 500mhz OPP as well?
So far no, as datasheet does NOT list 500MHz as OPP, this patch is just to make sure the speed grading mask settings matches the fusemap file, NOT sure if 500MHz will be supported officially.
Anson
Shawn Guo
AppliedQuoted 10 lines · Anson Huang
The 800MHz opp speed grading fuse mask should be
0xdinstead of0xfaccording to fuse map definition:SPEED_GRADING[1:0] MHz
00 800 01 500 10 1000 11 1200Signed-off-by Anson Huang <[email protected]>
Applied both, thanks.