serial: 8250_omap: Fix idling for unloaded serdev drivers
PATCH 1/1 serial: 8250_omap: Fix idling for unloaded serdev drivers
For many years omap variants have been setting the runtime PM autosuspend delay to -1 to prevent unsafe policy with lossy first character on wake-up. The user must specifically enable the timeout for UARTs if desired.
We must not enable the workaround for serdev devices though. It leads into UARTs not idling if no serdev devices are loaded and there is no sysfs entry to configure the UART in that case. And this means that my PM may not work unless the serdev modules are loaded.
We can detect a serdev device being configured based on a dts child node, and we can simply skip the workround in that case. And the serdev driver can idle the port during runtime when suitable if an out-of-band wake-up GPIO line exists for example.
Let's also add some comments to the workaround while at it.
--- drivers/tty/serial/8250/8250_omap.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)
drivers/tty/serial/8250/8250_omap.c +10 -1
@@ -1234,7 +1234,16 @@ static int omap8250_probe(struct platform_device *pdev)device_init_wakeup (&pdev->dev, true);pm_runtime_use_autosuspend (&pdev->dev); -pm_runtime_set_autosuspend_delay (&pdev->dev,-1 ); + +/* +* Disable runtime PM until autosuspend delay unless specifically +* enabled by the user via sysfs. This is the historic way to +* prevent an unsafe default policy with lossy characters on wake-up. +* For serdev devices this is not needed, the policy can be managed by +* the serdev driver. +*/ +if (!of_get_available_child_count (pdev->dev.of_node)) +pm_runtime_set_autosuspend_delay (&pdev->dev,-1 );pm_runtime_irq_safe (&pdev->dev);pm_runtime_enable (&pdev->dev);
Signature · 1 line
2.21.0
Quoted 11 lines · Tony Lindgren
For many years omap variants have been setting the runtime PM autosuspend delay to -1 to prevent unsafe policy with lossy first character on wake-up. The user must specifically enable the timeout for UARTs if desired.
We must not enable the workaround for serdev devices though. It leads into UARTs not idling if no serdev devices are loaded and there is no sysfs entry to configure the UART in that case. And this means that my PM may not work unless the serdev modules are loaded.
Quoted 6 lines
We can detect a serdev device being configured based on a dts child node, and we can simply skip the workround in that case. And the serdev driver can idle the port during runtime when suitable if an out-of-band wake-up GPIO line exists for example.
Let's also add some comments to the workaround while at it.
This seems to help some of the stability issues I am seeing on the DM3730 UART2 running Bluetooth at 3000000 baud.
Does it make sense to backport this to the stable kernels?
adam
Quoted 30 lines
Cc Johan Hovold <[email protected]>Signed-off-by Tony Lindgren <[email protected]>--- drivers/tty/serial/8250/8250_omap.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)drivers/tty/serial/8250/8250_omap.c +10
-2@@ -1234,7 +1234,16 @@ static int omap8250_probe(struct platform_device *pdev)device_init_wakeup (&pdev->dev, true);pm_runtime_use_autosuspend (&pdev->dev); -pm_runtime_set_autosuspend_delay (&pdev->dev,-1 ); + +/* +* Disable runtime PM until autosuspend delay unless specifically +* enabled by the user via sysfs. This is the historic way to +* prevent an unsafe default policy with lossy characters on wake-up. +* For serdev devices this is not needed, the policy can be managed by +* the serdev driver. +*/ +if (!of_get_available_child_count (pdev->dev.of_node)) +pm_runtime_set_autosuspend_delay (&pdev->dev,-1 );pm_runtime_irq_safe (&pdev->dev);pm_runtime_enable (&pdev->dev); --2.21.0
Quoted 17 lines · Adam Ford
Quoted 16 lines · Tony Lindgren
For many years omap variants have been setting the runtime PM autosuspend delay to -1 to prevent unsafe policy with lossy first character on wake-up. The user must specifically enable the timeout for UARTs if desired.
We must not enable the workaround for serdev devices though. It leads into UARTs not idling if no serdev devices are loaded and there is no sysfs entry to configure the UART in that case. And this means that my PM may not work unless the serdev modules are loaded.
We can detect a serdev device being configured based on a dts child node, and we can simply skip the workround in that case. And the serdev driver can idle the port during runtime when suitable if an out-of-band wake-up GPIO line exists for example.
Quoted 5 lines
Quoted 1 line
Let's also add some comments to the workaround while at it.
This seems to help some of the stability issues I am seeing on the DM3730 UART2 running Bluetooth at 3000000 baud.
Does it make sense to backport this to the stable kernels?
Sure if it helps with issues, it should be safe to apply to earlier kernels that have serdev potentially in use.
No need for earlier kernels before serdev though.
Regards,
Tony
Quoted 29 lines
Quoted 29 lines
Cc Johan Hovold <[email protected]>Signed-off-by Tony Lindgren <[email protected]>--- drivers/tty/serial/8250/8250_omap.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)drivers/tty/serial/8250/8250_omap.c +10
-2@@ -1234,7 +1234,16 @@ static int omap8250_probe(struct platform_device *pdev)device_init_wakeup (&pdev->dev, true);pm_runtime_use_autosuspend (&pdev->dev); -pm_runtime_set_autosuspend_delay (&pdev->dev,-1 ); + +/* +* Disable runtime PM until autosuspend delay unless specifically +* enabled by the user via sysfs. This is the historic way to +* prevent an unsafe default policy with lossy characters on wake-up. +* For serdev devices this is not needed, the policy can be managed by +* the serdev driver. +*/ +if (!of_get_available_child_count (pdev->dev.of_node)) +pm_runtime_set_autosuspend_delay (&pdev->dev,-1 );pm_runtime_irq_safe (&pdev->dev);pm_runtime_enable (&pdev->dev); --2.21.0