Skip to contentSkip to conversation

wlcore: clean-up clearing of WL1271_FLAG_IRQ_RUNNING

PATCH In review Tony Lindgren 2 participants 2 messages Oct 9, 2019 – Oct 11, 2019 1 message not in the archive TI wilink wireless drivers

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 wlcore: clean-up clearing of WL1271_FLAG_IRQ_RUNNING

We set WL1271_FLAG_IRQ_RUNNING in the beginning of wlcore_irq(), but clear it before interrupt handling is done in wlcore_irq_locked().

Let's move the clearing to the end of wlcore_irq() where it gets set, and remove the old comments about hardirq. That's no longer the case as we're using request_threaded_irq().

Note that the WL1271_FLAG_IRQ_RUNNING should never race between the interrupt handler and wlcore_runtime_resume() as because of autosuspend timeout we cannot enter idle between wlcore_irq_locked() and the end of wlcore_irq().

Cc Anders Roxell <[email protected]>
Cc Eyal Reizer <[email protected]>
Cc Guy Mishol <[email protected]>
Cc John Stultz <[email protected]>
Cc Ulf Hansson <[email protected]>

Changes since v2:

- Downgraded to clean-up from a fix as the race should never happen

Changes since v1:

- Add locking around clear_bit like we do elsewhere in the driver

---
 drivers/net/wireless/ti/wlcore/main.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/net/wireless/ti/wlcore/main.c +6 -6
@@ -544,11 +544,6 @@ static int wlcore_irq_locked(struct wl1271 *wl)
 	}
 
 	while (!done && loopcount--) {
-		/*
-		 * In order to avoid a race with the hardirq, clear the flag
-		 * before acknowledging the chip.
-		 */
-		clear_bit(WL1271_FLAG_IRQ_RUNNING, &wl->flags);
 		smp_mb__after_atomic();
 
 		ret = wlcore_fw_status(wl, wl->fw_status);
@@ -668,7 +663,7 @@ static irqreturn_t wlcore_irq(int irq, void *cookie)
 		disable_irq_nosync(wl->irq);
 		pm_wakeup_event(wl->dev, 0);
 		spin_unlock_irqrestore(&wl->wl_lock, flags);
-		return IRQ_HANDLED;
+		goto out_handled;
 	}
 	spin_unlock_irqrestore(&wl->wl_lock, flags);
 
@@ -692,6 +687,11 @@ static irqreturn_t wlcore_irq(int irq, void *cookie)
 
 	mutex_unlock(&wl->mutex);
 
+out_handled:
+	spin_lock_irqsave(&wl->wl_lock, flags);
+	clear_bit(WL1271_FLAG_IRQ_RUNNING, &wl->flags);
+	spin_unlock_irqrestore(&wl->wl_lock, flags);
+
 	return IRQ_HANDLED;
 }
 
Signature · 1 line
2.23.0

A message that is not in the archive (sent off-list or not yet received): 20191009165006.41567-1-tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org

#2 lore raw
Quoted 12 lines · Tony Lindgren

We set WL1271_FLAG_IRQ_RUNNING in the beginning of wlcore_irq(), but clear it before interrupt handling is done in wlcore_irq_locked().

Let's move the clearing to the end of wlcore_irq() where it gets set, and remove the old comments about hardirq. That's no longer the case as we're using request_threaded_irq().

Note that the WL1271_FLAG_IRQ_RUNNING should never race between the interrupt handler and wlcore_runtime_resume() as because of autosuspend timeout we cannot enter idle between wlcore_irq_locked() and the end of wlcore_irq().

Quoted 6 lines
Cc Anders Roxell <[email protected]>
Cc Eyal Reizer <[email protected]>
Cc Guy Mishol <[email protected]>
Cc John Stultz <[email protected]>
Cc Ulf Hansson <[email protected]>

Patch applied to wireless-drivers-next.git, thanks.

4633d30b61ac wlcore: clean-up clearing of WL1271_FLAG_IRQ_RUNNING

Signature · 3 lines
https://patchwork.kernel.org/patch/11181621/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches