arm64: dts: msm8916-longcheer-l8150: Enable WCNSS for WiFi and BT
PATCH 1/2 arm64: dts: msm8916-longcheer-l8150: Enable WCNSS for WiFi and BT
From: Nikita Travkin <[email protected]>
WCNSS is used on L8150 for WiFi and BT.
Its firmware isn't relocatable and must be loaded at specific address.
--- .../boot/dts/qcom/msm8916-longcheer-l8150.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts +14 -0
@@ -18,6 +18,16 @@ stdout-path = "serial0"; }; + reserved-memory { + // wcnss.mdt is not relocatable, so it must be loaded at 0x8b600000 + /delete-node/ wcnss@89300000; + + wcnss_mem: wcnss@8b600000 { + reg = <0x0 0x8b600000 0x0 0x600000>; + no-map; + }; + }; + soc { sdhci@7824000 { status = "okay";
@@ -68,6 +78,10 @@ }; }; + wcnss@a21b000 { + status = "okay"; + }; + /* * Attempting to enable these devices causes a "synchronous * external abort". Suspected cause is that the debug power
Signature · 1 line
2.19.1
PATCH 2/2 arm64: dts: msm8916-longcheer-l8150: Add Volume buttons
From: Nikita Travkin <[email protected]>
Add nodes for Volume UP button connected to GPIO and Volume DOWN button, which is handled by the pm8916 as is common with msm8916 devices.
--- .../boot/dts/qcom/msm8916-longcheer-l8150.dts | 41 +++++++++++++++++++ 1 file changed, 41 insertions(+)
arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts +41 -0
@@ -5,6 +5,7 @@ #include "msm8916.dtsi" #include "pm8916.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> / { model = "Longcheer L8150";
@@ -113,9 +114,36 @@ pinctrl-names = "default"; pinctrl-0 = <&usb_vbus_default>; }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; }; &msmgpio { + gpio_keys_default: gpio_keys_default { + pinmux { + function = "gpio"; + pins = "gpio107"; + }; + pinconf { + pins = "gpio107"; + drive-strength = <2>; + bias-pull-up; + }; + }; + usb_vbus_default: usb-vbus-default { pinmux { function = "gpio";
@@ -128,6 +156,19 @@ }; }; +&spmi_bus { + pm8916@0 { + pon@800 { + volume-down { + compatible = "qcom,pm8941-resin"; + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; + bias-pull-up; + linux,code = <KEY_VOLUMEDOWN>; + }; + }; + }; +}; + &smd_rpm_regulators { vdd_l1_l2_l3-supply = <&pm8916_s3>; vdd_l4_l5_l6-supply = <&pm8916_s4>;
Signature · 1 line
2.19.1
Re: [PATCH 2/2] arm64: dts: msm8916-longcheer-l8150: Add Volume buttons
Quoted 6 lines · On Sat, Oct 12, 2019 at 07:58:21PM +0500, [email protected] wrote:
From: Nikita Travkin <[email protected]>
Add nodes for Volume UP button connected to GPIO and Volume DOWN button, which is handled by the pm8916 as is common with msm8916 devices.
Signed-off-by Nikita Travkin <[email protected]>
Quoted 76 lines
--- .../boot/dts/qcom/msm8916-longcheer-l8150.dts | 41 +++++++++++++++++++ 1 file changed, 41 insertions(+)arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts +41
-0@@ -5,6 +5,7 @@ #include "msm8916.dtsi" #include "pm8916.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> / { model = "Longcheer L8150";@@ -113,9 +114,36 @@ pinctrl-names = "default"; pinctrl-0 = <&usb_vbus_default>; }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; }; &msmgpio { + gpio_keys_default: gpio_keys_default { + pinmux { + function = "gpio"; + pins = "gpio107"; + }; + pinconf { + pins = "gpio107"; + drive-strength = <2>; + bias-pull-up; + }; + }; + usb_vbus_default: usb-vbus-default { pinmux { function = "gpio";@@ -128,6 +156,19 @@ }; }; +&spmi_bus { + pm8916@0 { + pon@800 { + volume-down { + compatible = "qcom,pm8941-resin"; + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; + bias-pull-up; + linux,code = <KEY_VOLUMEDOWN>; + }; + }; + }; +}; + &smd_rpm_regulators { vdd_l1_l2_l3-supply = <&pm8916_s3>; vdd_l4_l5_l6-supply = <&pm8916_s4>;Signature · 1 line
2.19.1
Quoted 6 lines · On Sat, Oct 12, 2019 at 07:58:20PM +0500, [email protected] wrote:
From: Nikita Travkin <[email protected]>
WCNSS is used on L8150 for WiFi and BT.
Its firmware isn't relocatable and must be loaded at specific address.Signed-off-by Nikita Travkin <[email protected]>
Quoted 39 lines
--- .../boot/dts/qcom/msm8916-longcheer-l8150.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+)arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts +14
-0@@ -18,6 +18,16 @@ stdout-path = "serial0"; }; + reserved-memory { + // wcnss.mdt is not relocatable, so it must be loaded at 0x8b600000 + /delete-node/ wcnss@89300000; + + wcnss_mem: wcnss@8b600000 { + reg = <0x0 0x8b600000 0x0 0x600000>; + no-map; + }; + }; + soc { sdhci@7824000 { status = "okay";@@ -68,6 +78,10 @@ }; }; + wcnss@a21b000 { + status = "okay"; + }; + /* * Attempting to enable these devices causes a "synchronous * external abort". Suspected cause is that the debug powerSignature · 1 line
2.19.1
Quoted 6 lines · On Sat 12 Oct 07:58 PDT 2019, [email protected] wrote:
From: Nikita Travkin <[email protected]>
WCNSS is used on L8150 for WiFi and BT.
Its firmware isn't relocatable and must be loaded at specific address.Signed-off-by Nikita Travkin <[email protected]>
Both patches applied
Thank you,
Bjorn
Quoted 39 lines
--- .../boot/dts/qcom/msm8916-longcheer-l8150.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+)arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts +14
-0@@ -18,6 +18,16 @@ stdout-path = "serial0"; }; + reserved-memory { + // wcnss.mdt is not relocatable, so it must be loaded at 0x8b600000 + /delete-node/ wcnss@89300000; + + wcnss_mem: wcnss@8b600000 { + reg = <0x0 0x8b600000 0x0 0x600000>; + no-map; + }; + }; + soc { sdhci@7824000 { status = "okay";@@ -68,6 +78,10 @@ }; }; + wcnss@a21b000 { + status = "okay"; + }; + /* * Attempting to enable these devices causes a "synchronous * external abort". Suspected cause is that the debug powerSignature · 1 line
2.19.1