net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs
Subsystems (3)
PATCH v4 1/2 net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs in the micrel PHY driver, it is used even with the KSZ87xx switch. This is wrong, since the KSZ8051 configures registers of the PHY which are not present on the simplified KSZ87xx switch PHYs and misconfigures other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the KSZ87xx switch by checking the Basic Status register Bit 0, which is read-only and indicates presence of the Extended Capability Registers. The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct PHY driver instance.
---
NOTE: It was also suggested to populate phydev->dev_flags to discern
the PHY from the switch, this does not work for setups where the switch is used as a PHY without a DSA driver. Checking the BMSR Bit 0 for Extended Capability Register works for both DSA and non-DSA usecase.
V2: Move phy_id check into ksz8051_match_phy_device() and
ksz8795_match_phy_device() and drop phy_id{,_mask} from the ksphy_driver[] list to avoid matching on other PHY IDs.
V3: Pull the logic behind discerning the KSZ8051 PHY and KSZ87xx switch
into common ksz8051_ksz8795_match_phy_device() function. Add Fixes tag.
V4: No functional change at all. Just reorder the Fixes: tag to the
correct place above the Cc tags and add another net tag after PATCH into subject.
--- drivers/net/phy/micrel.c | 40 ++++++++++++++++++++++++++++++++++++---- 1 file changed, 36 insertions(+), 4 deletions(-)
drivers/net/phy/micrel.c +36 -4
@@ -341,6 +341,35 @@ static int ksz8041_config_aneg(struct phy_device *phydev)return genphy_config_aneg (phydev); } +static int ksz8051_ksz8795_match_phy_device (struct phy_device *phydev, +const u32 ksz_phy_id) +{ +int ret; + +if ((phydev->phy_id &MICREL_PHY_ID_MASK ) != ksz_phy_id) +return 0 ; + + ret =phy_read (phydev,MII_BMSR ); +if (ret <0 ) +return ret; + +/* KSZ8051 PHY and KSZ8794/KSZ8795/KSZ8765 switch share the same +* exact PHY ID. However, they can be told apart by the extended +* capability registers presence. The KSZ8051 PHY has them while +* the switch does not. +*/ + ret &=BMSR_ERCAP ; +if (ksz_phy_id ==PHY_ID_KSZ8051 ) +return ret; +else +return !ret; +} + +static int ksz8051_match_phy_device (struct phy_device *phydev) +{ +return ksz8051_ksz8795_match_phy_device (phydev,PHY_ID_KSZ8051 ); +} +static int ksz8081_config_init (struct phy_device *phydev) {/* KSZPHY_OMSO_FACTORY_TEST is set at de-assertion of the reset line
@@ -364,6 +393,11 @@ static int ksz8061_config_init(struct phy_device *phydev)return kszphy_config_init (phydev); } +static int ksz8795_match_phy_device (struct phy_device *phydev) +{ +return ksz8051_ksz8795_match_phy_device (phydev,PHY_ID_KSZ8795 ); +} + static int ksz9021_load_values_from_of(struct phy_device *phydev, const struct device_node *of_node, u16 reg,
@@ -1017,8 +1051,6 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = genphy_resume, }, { - .phy_id = PHY_ID_KSZ8051, - .phy_id_mask = MICREL_PHY_ID_MASK, .name = "Micrel KSZ8051", /* PHY_BASIC_FEATURES */ .driver_data = &ksz8051_type,
@@ -1029,6 +1061,7 @@ static struct phy_driver ksphy_driver[] = { .get_sset_count = kszphy_get_sset_count, .get_strings = kszphy_get_strings, .get_stats = kszphy_get_stats, + .match_phy_device = ksz8051_match_phy_device, .suspend = genphy_suspend, .resume = genphy_resume, }, {
@@ -1141,13 +1174,12 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = genphy_resume, }, { - .phy_id = PHY_ID_KSZ8795, - .phy_id_mask = MICREL_PHY_ID_MASK, .name = "Micrel KSZ8795",/* PHY_BASIC_FEATURES */ .config_init = kszphy_config_init, .config_aneg = ksz8873mll_config_aneg, .read_status = ksz8873mll_read_status, + .match_phy_device = ksz8795_match_phy_device, .suspend = genphy_suspend, .resume = genphy_resume, }, {
Signature · 1 line
2.23.0
PATCH v4 2/2 net: phy: micrel: Update KSZ87xx PHY name
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches. Update the PHY ID and name to reflect that, as this family of switches is commonly refered to as KSZ87xx
---
V2: Rebase on top of 1/2, no functional change
V3: Rebase on top of 1/2, no functional change
V4: No functional change at all. Add another net tag after PATCH into subject.
--- drivers/net/phy/micrel.c | 4 ++-- include/linux/micrel_phy.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)
drivers/net/phy/micrel.c +2 -2
@@ -395,7 +395,7 @@ static int ksz8061_config_init(struct phy_device *phydev)static int ksz8795_match_phy_device (struct phy_device *phydev) { -return ksz8051_ksz8795_match_phy_device (phydev,PHY_ID_KSZ8795 ); +return ksz8051_ksz8795_match_phy_device (phydev,PHY_ID_KSZ87XX ); } static int ksz9021_load_values_from_of(struct phy_device *phydev,
@@ -1174,7 +1174,7 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = genphy_resume, }, { - .name = "Micrel KSZ8795", + .name = "Micrel KSZ87XX Switch", /* PHY_BASIC_FEATURES */ .config_init = kszphy_config_init, .config_aneg = ksz8873mll_config_aneg,
include/linux/micrel_phy.h +1 -1
@@ -31,7 +31,7 @@#define PHY_ID_KSZ886X 0x00221430#define PHY_ID_KSZ8863 0x00221435 -#define PHY_ID_KSZ8795 0x00221550 +#define PHY_ID_KSZ87XX 0x00221550#define PHY_ID_KSZ9477 0x00221631
Signature · 1 line
2.23.0
Re: [PATCH net V4 2/2] net: phy: micrel: Update KSZ87xx PHY name
Quoted 5 lines · Marek Vasut
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches. Update the PHY ID and name to reflect that, as this family of switches is commonly refered to as KSZ87xx
Signed-off-by Marek Vasut <[email protected]>
Andrew
Quoted 12 lines · Marek Vasut
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs in the micrel PHY driver, it is used even with the KSZ87xx switch. This is wrong, since the KSZ8051 configures registers of the PHY which are not present on the simplified KSZ87xx switch PHYs and misconfigures other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the KSZ87xx switch by checking the Basic Status register Bit 0, which is read-only and indicates presence of the Extended Capability Registers. The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
Quoted 6 lines
This patch implements simple check for the presence of this bit for both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct PHY driver instance.
Signed-off-by Marek Vasut <[email protected]>Fixes 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Andrew
David Miller
maintainerFrom: Marek Vasut <[email protected]>
Date: Sun, 13 Oct 2019 23:24:03 +0200
Quoted 2 lines
Signed-off-by Marek Vasut <[email protected]>Fixes 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
I'm sorry to be strict, but as Heiner said the Fixes: tag needs to be the first tag.
I'm pushing this back to you so that you can learn how to submit patches properly in the future, nothing more.
Thank you.
Quoted 11 lines · David Miller
From: Marek Vasut <[email protected]>
Date: Sun, 13 Oct 2019 23:24:03 +0200Quoted 2 lines
Signed-off-by Marek Vasut <[email protected]>Fixes 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")I'm sorry to be strict, but as Heiner said the Fixes: tag needs to be the first tag.
I'm pushing this back to you so that you can learn how to submit patches properly in the future, nothing more.
Maybe next time we can do these exercises on patches which are not bugfixes for real issues?
David Miller
maintainerFrom: Marek Vasut <[email protected]>
Date: Wed, 16 Oct 2019 15:39:18 +0200
Quoted 2 lines
Maybe next time we can do these exercises on patches which are not bugfixes for real issues?
No, we should put changes into the tree which are correctly formed.
If you're not interested in learning how to submit changes properly, we am not interested in accepting your work.
It's as simple as that.
Quoted 6 lines · David Miller
From: Marek Vasut
Date: Wed, 16 Oct 2019 15:39:18 +0200Quoted 2 lines
Maybe next time we can do these exercises on patches which are not bugfixes for real issues?
Quoted 6 lines
No, we should put changes into the tree which are correctly formed.
If you're not interested in learning how to submit changes properly, we am not interested in accepting your work.
It's as simple as that.
If I wasn't interested, I wouldn't have sent V5 before replying to the previous email. I hope the V5 is fine.