Skip to contentSkip to conversation

staging: sm750fb: Edit CamelCase in ddk750_mode files

PATCH Superseded Jamal Shareef 2 participants 2 messages Oct 17, 2019

Subsystems (2)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 staging: sm750fb: Edit CamelCase in ddk750_mode files

Edit CamelCase naming in ddk750 files and
in dependent file sm750_hw.c.

Issue found by checkpatch.

---
 drivers/staging/sm750fb/ddk750_mode.c | 86 +++++++++++++--------------
 drivers/staging/sm750fb/ddk750_mode.h |  2 +-
 drivers/staging/sm750fb/sm750_hw.c    |  2 +-
 3 files changed, 45 insertions(+), 45 deletions(-)
drivers/staging/sm750fb/ddk750_mode.c +43 -43
index e00a6cb31947..f08dcab29172 100644
@@ -14,13 +14,13 @@
  * in bit 29:27 of Display Control register.
  */
 static unsigned long
-displayControlAdjust_SM750LE(struct mode_parameter *pModeParam,
-			     unsigned long dispControl)
+display_control_adjust_SM750LE(struct mode_parameter *p_mode_param,
+			       unsigned long disp_control)
 {
 	unsigned long x, y;
 
-	x = pModeParam->horizontal_display_end;
-	y = pModeParam->vertical_display_end;
+	x = p_mode_param->horizontal_display_end;
+	y = p_mode_param->vertical_display_end;
 
 	/*
 	 * SM750LE has to set up the top-left and bottom-right
@@ -42,41 +42,41 @@ displayControlAdjust_SM750LE(struct mode_parameter *pModeParam,
 	 */
 
 	/* Clear bit 29:27 of display control register */
-	dispControl &= ~CRT_DISPLAY_CTRL_CLK_MASK;
+	disp_control &= ~CRT_DISPLAY_CTRL_CLK_MASK;
 
 	/* Set bit 29:27 of display control register for the right clock */
 	/* Note that SM750LE only need to supported 7 resolutions. */
 	if (x == 800 && y == 600)
-		dispControl |= CRT_DISPLAY_CTRL_CLK_PLL41;
+		disp_control |= CRT_DISPLAY_CTRL_CLK_PLL41;
 	else if (x == 1024 && y == 768)
-		dispControl |= CRT_DISPLAY_CTRL_CLK_PLL65;
+		disp_control |= CRT_DISPLAY_CTRL_CLK_PLL65;
 	else if (x == 1152 && y == 864)
-		dispControl |= CRT_DISPLAY_CTRL_CLK_PLL80;
+		disp_control |= CRT_DISPLAY_CTRL_CLK_PLL80;
 	else if (x == 1280 && y == 768)
-		dispControl |= CRT_DISPLAY_CTRL_CLK_PLL80;
+		disp_control |= CRT_DISPLAY_CTRL_CLK_PLL80;
 	else if (x == 1280 && y == 720)
-		dispControl |= CRT_DISPLAY_CTRL_CLK_PLL74;
+		disp_control |= CRT_DISPLAY_CTRL_CLK_PLL74;
 	else if (x == 1280 && y == 960)
-		dispControl |= CRT_DISPLAY_CTRL_CLK_PLL108;
+		disp_control |= CRT_DISPLAY_CTRL_CLK_PLL108;
 	else if (x == 1280 && y == 1024)
-		dispControl |= CRT_DISPLAY_CTRL_CLK_PLL108;
+		disp_control |= CRT_DISPLAY_CTRL_CLK_PLL108;
 	else /* default to VGA clock */
-		dispControl |= CRT_DISPLAY_CTRL_CLK_PLL25;
+		disp_control |= CRT_DISPLAY_CTRL_CLK_PLL25;
 
 	/* Set bit 25:24 of display controller */
-	dispControl |= (CRT_DISPLAY_CTRL_CRTSELECT | CRT_DISPLAY_CTRL_RGBBIT);
+	disp_control |= (CRT_DISPLAY_CTRL_CRTSELECT | CRT_DISPLAY_CTRL_RGBBIT);
 
 	/* Set bit 14 of display controller */
-	dispControl |= DISPLAY_CTRL_CLOCK_PHASE;
+	disp_control |= DISPLAY_CTRL_CLOCK_PHASE;
 
-	poke32(CRT_DISPLAY_CTRL, dispControl);
+	poke32(CRT_DISPLAY_CTRL, disp_control);
 
-	return dispControl;
+	return disp_control;
 }
 
 /* only timing related registers will be  programed */
-static int programModeRegisters(struct mode_parameter *pModeParam,
-				struct pll_value *pll)
+static int program_mode_registers(struct mode_parameter *p_mode_param,
+				  struct pll_value *pll)
 {
 	int ret = 0;
 	int cnt = 0;
@@ -86,46 +86,46 @@ static int programModeRegisters(struct mode_parameter *pModeParam,
 		/* programe secondary pixel clock */
 		poke32(CRT_PLL_CTRL, sm750_format_pll_reg(pll));
 
-		tmp = ((pModeParam->horizontal_total - 1) <<
+		tmp = ((p_mode_param->horizontal_total - 1) <<
 		       CRT_HORIZONTAL_TOTAL_TOTAL_SHIFT) &
 		     CRT_HORIZONTAL_TOTAL_TOTAL_MASK;
-		tmp |= (pModeParam->horizontal_display_end - 1) &
+		tmp |= (p_mode_param->horizontal_display_end - 1) &
 		      CRT_HORIZONTAL_TOTAL_DISPLAY_END_MASK;
 
 		poke32(CRT_HORIZONTAL_TOTAL, tmp);
 
-		tmp = (pModeParam->horizontal_sync_width <<
+		tmp = (p_mode_param->horizontal_sync_width <<
 		       CRT_HORIZONTAL_SYNC_WIDTH_SHIFT) &
 		     CRT_HORIZONTAL_SYNC_WIDTH_MASK;
-		tmp |= (pModeParam->horizontal_sync_start - 1) &
+		tmp |= (p_mode_param->horizontal_sync_start - 1) &
 		      CRT_HORIZONTAL_SYNC_START_MASK;
 
 		poke32(CRT_HORIZONTAL_SYNC, tmp);
 
-		tmp = ((pModeParam->vertical_total - 1) <<
+		tmp = ((p_mode_param->vertical_total - 1) <<
 		       CRT_VERTICAL_TOTAL_TOTAL_SHIFT) &
 		     CRT_VERTICAL_TOTAL_TOTAL_MASK;
-		tmp |= (pModeParam->vertical_display_end - 1) &
+		tmp |= (p_mode_param->vertical_display_end - 1) &
 		      CRT_VERTICAL_TOTAL_DISPLAY_END_MASK;
 
 		poke32(CRT_VERTICAL_TOTAL, tmp);
 
-		tmp = ((pModeParam->vertical_sync_height <<
+		tmp = ((p_mode_param->vertical_sync_height <<
 		       CRT_VERTICAL_SYNC_HEIGHT_SHIFT)) &
 		     CRT_VERTICAL_SYNC_HEIGHT_MASK;
-		tmp |= (pModeParam->vertical_sync_start - 1) &
+		tmp |= (p_mode_param->vertical_sync_start - 1) &
 		      CRT_VERTICAL_SYNC_START_MASK;
 
 		poke32(CRT_VERTICAL_SYNC, tmp);
 
 		tmp = DISPLAY_CTRL_TIMING | DISPLAY_CTRL_PLANE;
-		if (pModeParam->vertical_sync_polarity)
+		if (p_mode_param->vertical_sync_polarity)
 			tmp |= DISPLAY_CTRL_VSYNC_PHASE;
-		if (pModeParam->horizontal_sync_polarity)
+		if (p_mode_param->horizontal_sync_polarity)
 			tmp |= DISPLAY_CTRL_HSYNC_PHASE;
 
 		if (sm750_get_chip_type() == SM750LE) {
-			displayControlAdjust_SM750LE(pModeParam, tmp);
+			display_control_adjust_SM750LE(p_mode_param, tmp);
 		} else {
 			reg = peek32(CRT_DISPLAY_CTRL) &
 				~(DISPLAY_CTRL_VSYNC_PHASE |
@@ -140,40 +140,40 @@ static int programModeRegisters(struct mode_parameter *pModeParam,
 
 		poke32(PANEL_PLL_CTRL, sm750_format_pll_reg(pll));
 
-		reg = ((pModeParam->horizontal_total - 1) <<
+		reg = ((p_mode_param->horizontal_total - 1) <<
 			PANEL_HORIZONTAL_TOTAL_TOTAL_SHIFT) &
 			PANEL_HORIZONTAL_TOTAL_TOTAL_MASK;
-		reg |= ((pModeParam->horizontal_display_end - 1) &
+		reg |= ((p_mode_param->horizontal_display_end - 1) &
 			PANEL_HORIZONTAL_TOTAL_DISPLAY_END_MASK);
 		poke32(PANEL_HORIZONTAL_TOTAL, reg);
 
 		poke32(PANEL_HORIZONTAL_SYNC,
-		       ((pModeParam->horizontal_sync_width <<
+		       ((p_mode_param->horizontal_sync_width <<
 			 PANEL_HORIZONTAL_SYNC_WIDTH_SHIFT) &
 			PANEL_HORIZONTAL_SYNC_WIDTH_MASK) |
-		       ((pModeParam->horizontal_sync_start - 1) &
+		       ((p_mode_param->horizontal_sync_start - 1) &
 			PANEL_HORIZONTAL_SYNC_START_MASK));
 
 		poke32(PANEL_VERTICAL_TOTAL,
-		       (((pModeParam->vertical_total - 1) <<
+		       (((p_mode_param->vertical_total - 1) <<
 			 PANEL_VERTICAL_TOTAL_TOTAL_SHIFT) &
 			PANEL_VERTICAL_TOTAL_TOTAL_MASK) |
-		       ((pModeParam->vertical_display_end - 1) &
+		       ((p_mode_param->vertical_display_end - 1) &
 			PANEL_VERTICAL_TOTAL_DISPLAY_END_MASK));
 
 		poke32(PANEL_VERTICAL_SYNC,
-		       ((pModeParam->vertical_sync_height <<
+		       ((p_mode_param->vertical_sync_height <<
 			 PANEL_VERTICAL_SYNC_HEIGHT_SHIFT) &
 			PANEL_VERTICAL_SYNC_HEIGHT_MASK) |
-		       ((pModeParam->vertical_sync_start - 1) &
+		       ((p_mode_param->vertical_sync_start - 1) &
 			PANEL_VERTICAL_SYNC_START_MASK));
 
 		tmp = DISPLAY_CTRL_TIMING | DISPLAY_CTRL_PLANE;
-		if (pModeParam->vertical_sync_polarity)
+		if (p_mode_param->vertical_sync_polarity)
 			tmp |= DISPLAY_CTRL_VSYNC_PHASE;
-		if (pModeParam->horizontal_sync_polarity)
+		if (p_mode_param->horizontal_sync_polarity)
 			tmp |= DISPLAY_CTRL_HSYNC_PHASE;
-		if (pModeParam->clock_phase_polarity)
+		if (p_mode_param->clock_phase_polarity)
 			tmp |= DISPLAY_CTRL_CLOCK_PHASE;
 
 		reserved = PANEL_DISPLAY_CTRL_RESERVED_MASK |
@@ -207,7 +207,7 @@ static int programModeRegisters(struct mode_parameter *pModeParam,
 	return ret;
 }
 
-int ddk750_setModeTiming(struct mode_parameter *parm, enum clock_type clock)
+int ddk750_set_mode_timing(struct mode_parameter *parm, enum clock_type clock)
 {
 	struct pll_value pll;
 
@@ -220,6 +220,6 @@ int ddk750_setModeTiming(struct mode_parameter *parm, enum clock_type clock)
 		outb_p(0x88, 0x3d4);
 		outb_p(0x06, 0x3d5);
 	}
-	programModeRegisters(parm, &pll);
+	program_mode_registers(parm, &pll);
 	return 0;
 }
drivers/staging/sm750fb/ddk750_mode.h +1 -1
index 2df78a0937b2..1b70885f85e5 100644
@@ -33,5 +33,5 @@ struct mode_parameter {
 	enum spolarity clock_phase_polarity;
 };
 
-int ddk750_setModeTiming(struct mode_parameter *parm, enum clock_type clock);
+int ddk750_set_mode_timing(struct mode_parameter *parm, enum clock_type clock);
 #endif
drivers/staging/sm750fb/sm750_hw.c +1 -1
index ea1d3d4efbc2..15ac73821ab5 100644
@@ -305,7 +305,7 @@ int hw_sm750_crtc_setMode(struct lynxfb_crtc *crtc,
 		clock = SECONDARY_PLL;
 
 	pr_debug("Request pixel clock = %lu\n", modparm.pixel_clock);
-	ret = ddk750_setModeTiming(&modparm, clock);
+	ret = ddk750_set_mode_timing(&modparm, clock);
 	if (ret) {
 		pr_err("Set mode timing failed\n");
 		goto exit;
Signature · 1 line
2.17.1
maintainer
#1 lore raw
Quoted 17 lines · Jamal Shareef

Edit CamelCase naming in ddk750 files and
in dependent file sm750_hw.c.

Issue found by checkpatch.

---
 drivers/staging/sm750fb/ddk750_mode.c | 86 +++++++++++++--------------
 drivers/staging/sm750fb/ddk750_mode.h |  2 +-
 drivers/staging/sm750fb/sm750_hw.c    |  2 +-
 3 files changed, 45 insertions(+), 45 deletions(-)
drivers/staging/sm750fb/ddk750_mode.c +0 -0
index e00a6cb31947..f08dcab29172 100644

drivers/staging/sm750fb/ddk750_mode.c line 17

Quoted 6 lines
drivers/staging/sm750fb/ddk750_mode.c +1 -2
@@ -14,13 +14,13 @@
  * in bit 29:27 of Display Control register.
  */
 static unsigned long
-displayControlAdjust_SM750LE(struct mode_parameter *pModeParam,
-			     unsigned long dispControl)
+display_control_adjust_SM750LE(struct mode_parameter *p_mode_param,

Hm, sorry, but this isn't going to work.

Look at the variable name and try to understand why the original name was called that. The name was using something called Hungarian notation for how it was called. That "method" involves putting the "type" of the variable in the name itself, and comes from before we had compilers that would check those types of things (pun intended...)

The "p" here means "pointer". When renaming it, you don't need that "p" at all, so it should just be "mode_param" instead.

So please fix up everywhere.

thanks,

greg k-h