staging: vc04_services: fix check warnings of line over 80 characters
Subsystems (2)
PATCH v2 1/1 staging: vc04_services: fix check warnings of line over 80 characters
Fix warnings of line over 80 characters.
Issue detected by checkepatch tool.
Signed-off-by Jules Irenge <[email protected]>
--- .../vc04_services/interface/vchi/vchi_cfg.h | 168 +++++++++++------- 1 file changed, 106 insertions(+), 62 deletions(-)
drivers/staging/vc04_services/interface/vchi/vchi_cfg.h +106 -62
@@ -4,13 +4,17 @@#ifndef VCHI_CFG_H_ #define VCHI_CFG_H_ -/**************************************************************************************** -* Defines in this first section are part of the VCHI API and may be examined by VCHI -* services. -***************************************************************************************/ - -/* Required alignment of base addresses for bulk transfer, if unaligned transfers are not enabled */ -/* Really determined by the message driver, and should be available from a run-time call. */ +/******************************************************************************* +* Defines in this first section are part of the VCHI API and may be examined by +* VCHI services. +******************************************************************************/ + +/* +* Required alignment of base addresses for bulk transfer, if unaligned +* transfers are not enabled +* Really determined by the message driver, and should be available from +* a run-time call. +*/ #ifndef VCHI_BULK_ALIGN # if __VCCOREVER__ >=0x04000000 # define VCHI_BULK_ALIGN 32 // Allows for the need to do cache cleans
@@ -19,9 +23,13 @@# endif #endif -/* Required length multiple for bulk transfers, if unaligned transfers are not enabled */ -/* May be less than or greater than VCHI_BULK_ALIGN */ -/* Really determined by the message driver, and should be available from a run-time call. */ +/* +* Required length multiple for bulk transfers, if unaligned transfers are +* not enabled +* May be less than or greater than VCHI_BULK_ALIGN +* Really determined by the message driver, and should be available from +* a run-time call. +*/ #ifndef VCHI_BULK_GRANULARITY # if __VCCOREVER__ >=0x04000000 # define VCHI_BULK_GRANULARITY 32 // Allows for the need to do cache cleans
@@ -39,19 +47,24 @@# endif #endif -/****************************************************************************************** -* Defines below are system configuration options, and should not be used by VCHI services. -*****************************************************************************************/ +/****************************************************************************** +* Defines below are system configuration options, and should not be used by +* VCHI services. +******************************************************************************/ -/* How many connections can we support? A localhost implementation uses 2 connections, -* 1 for host-app, 1 for VMCS, and these are hooked together by a loopback MPHI VCFW -* driver. */ +/* +* How many connections can we support? A localhost implementation uses +* 2 connections, 1 for host-app, 1 for VMCS, and these are hooked together +* by a loopback MPHI VCFW driver. +*/ #ifndef VCHI_MAX_NUM_CONNECTIONS # define VCHI_MAX_NUM_CONNECTIONS 3#endif -/* How many services can we open per connection? Extending this doesn't cost processing time, just a small -* amount of static memory. */ +/* +* How many services can we open per connection? Extending this doesn't cost +* processing time, just a small amount of static memory. +*/ #ifndef VCHI_MAX_SERVICES_PER_CONNECTION # define VCHI_MAX_SERVICES_PER_CONNECTION 36#endif
@@ -66,8 +79,10 @@# define VCHI_MAX_BULK_RX_CHANNELS_PER_CONNECTION 1 // 1 MPHI#endif -/* How many receive slots do we use. This times VCHI_MAX_MSG_SIZE gives the effective -* receive queue space, less message headers. */ +/* +* How many receive slots do we use. This times VCHI_MAX_MSG_SIZE gives the +* effective receive queue space, less message headers. +*/ #ifndef VCHI_NUM_READ_SLOTS # if defined(VCHI_LOCAL_HOST_PORT )# define VCHI_NUM_READ_SLOTS 4
@@ -76,112 +91,141 @@# endif #endif -/* Do we utilise overrun facility for receive message slots? Can aid peer transmit -* performance. Only define on VideoCore end, talking to host. +/* +* Do we utilise overrun facility for receive message slots? Can aid peer +* transmit performance. Only define on VideoCore end, talking to host. */ //#define VCHI_MSG_RX_OVERRUN -/* How many transmit slots do we use. Generally don't need many, as the hardware driver -* underneath VCHI will usually have its own buffering. */ +/* +* How many transmit slots do we use. Generally don't need many, +* as the hardware driver underneath VCHI will usually have its own buffering. +*/ #ifndef VCHI_NUM_WRITE_SLOTS # define VCHI_NUM_WRITE_SLOTS 4#endif -/* If a service has held or queued received messages in VCHI_XOFF_THRESHOLD or more slots, -* then it's taking up too much buffer space, and the peer service will be told to stop -* transmitting with an XOFF message. For this to be effective, the VCHI_NUM_READ_SLOTS -* needs to be considerably bigger than VCHI_NUM_WRITE_SLOTS, or the transmit latency -* is too high. */ +/* +* If a service has held or queued received messages in VCHI_XOFF_THRESHOLD or +* more slots, then it's taking up too much buffer space, +* and the peer service will be told to stop transmitting with an XOFF message. +* For this to be effective, the VCHI_NUM_READ_SLOTS needs to be considerably +* bigger than VCHI_NUM_WRITE_SLOTS, or the transmit latency is too high. +*/ #ifndef VCHI_XOFF_THRESHOLD # define VCHI_XOFF_THRESHOLD (VCHI_NUM_READ_SLOTS / 2)#endif -/* After we've sent an XOFF, the peer will be told to resume transmission once the local -* service has dequeued/released enough messages that it's now occupying -* VCHI_XON_THRESHOLD slots or fewer. */ +/* +* After we've sent an XOFF, the peer will be told to resume transmission +* once the local service has dequeued/released enough messages that it's now +* occupying VCHI_XON_THRESHOLD slots or fewer. +*/ #ifndef VCHI_XON_THRESHOLD # define VCHI_XON_THRESHOLD (VCHI_NUM_READ_SLOTS / 4)#endif -/* A size below which a bulk transfer omits the handshake completely and always goes -* via the message channel, if bulk auxiliary is being sent on that service. (The user -* can guarantee this by enabling unaligned transmits). -* Not API. */ +/* +* A size below which a bulk transfer omits the handshake completely and always +* goes via the message channel, if bulk auxiliary is being sent on that +* service. (The user can guarantee this by enabling unaligned transmits). +* Not API. +*/ #ifndef VCHI_MIN_BULK_SIZE # define VCHI_MIN_BULK_SIZE (VCHI_MAX_MSG_SIZE / 2 < 4096 ? VCHI_MAX_MSG_SIZE / 2 : 4096)#endif -/* Maximum size of bulk transmission chunks, for each interface type. A trade-off between -* speed and latency; the smaller the chunk size the better change of messages and other -* bulk transmissions getting in when big bulk transfers are happening. Set to 0 to not -* break transmissions into chunks. +/* +* Maximum size of bulk transmission chunks, for each interface type. +* A trade-off between speed and latency; the smaller the chunk size the better +* change of messages and other bulk transmissions getting in when big bulk +* transfers are happening. Set to 0 to not break transmissions into chunks. */ #ifndef VCHI_MAX_BULK_CHUNK_SIZE_MPHI # define VCHI_MAX_BULK_CHUNK_SIZE_MPHI (16 * 1024)#endif -/* NB Chunked CCP2 transmissions violate the letter of the CCP2 spec by using "JPEG8" mode -* with multiple-line frames. Only use if the receiver can cope. */ +/* +* NB Chunked CCP2 transmissions violate the letter of the CCP2 spec +* by using "JPEG8" mode with multiple-line frames. Only use if the receiver +* can cope. +*/ #ifndef VCHI_MAX_BULK_CHUNK_SIZE_CCP2 # define VCHI_MAX_BULK_CHUNK_SIZE_CCP2 0#endif -/* How many TX messages can we have pending in our transmit slots. Once exhausted, -* vchi_msg_queue will be blocked. */ +/* +* How many TX messages can we have pending in our transmit slots. +* Once exhausted, vchi_msg_queue will be blocked. +*/ #ifndef VCHI_TX_MSG_QUEUE_SIZE # define VCHI_TX_MSG_QUEUE_SIZE 256#endif -/* How many RX messages can we have parsed in the receive slots. Once exhausted, parsing -* will be suspended until older messages are dequeued/released. */ +/* +* How many RX messages can we have parsed in the receive slots. Once exhausted, +* parsing will be suspended until older messages are dequeued/released. +*/ #ifndef VCHI_RX_MSG_QUEUE_SIZE # define VCHI_RX_MSG_QUEUE_SIZE 256#endif -/* Really should be able to cope if we run out of received message descriptors, by -* suspending parsing as the comment above says, but we don't. This sweeps the issue -* under the carpet. */ +/* +* Really should be able to cope if we run out of received message descriptors, +* by suspending parsing as the comment above says, but we don't. +* This sweeps the issue under the carpet. +*/ #if VCHI_RX_MSG_QUEUE_SIZE < (VCHI_MAX_MSG_SIZE /16 +1 ) *VCHI_NUM_READ_SLOTS # undef VCHI_RX_MSG_QUEUE_SIZE# define VCHI_RX_MSG_QUEUE_SIZE ((VCHI_MAX_MSG_SIZE/16 + 1) * VCHI_NUM_READ_SLOTS)#endif -/* How many bulk transmits can we have pending. Once exhausted, vchi_bulk_queue_transmit -* will be blocked. */ +/* +* How many bulk transmits can we have pending. Once exhausted, +* vchi_bulk_queue_transmit will be blocked. +*/ #ifndef VCHI_TX_BULK_QUEUE_SIZE # define VCHI_TX_BULK_QUEUE_SIZE 64#endif -/* How many bulk receives can we have pending. Once exhausted, vchi_bulk_queue_receive -* will be blocked. */ +/* +* How many bulk receives can we have pending. Once exhausted, +*vchi_bulk_queue_receive will be blocked. +*/ #ifndef VCHI_RX_BULK_QUEUE_SIZE # define VCHI_RX_BULK_QUEUE_SIZE 64#endif -/* A limit on how many outstanding bulk requests we expect the peer to give us. If -* the peer asks for more than this, VCHI will fail and assert. The number is determined -* by the peer's hardware - it's the number of outstanding requests that can be queued -* on all bulk channels. VC3's MPHI peripheral allows 16. */ +/* +* A limit on how many outstanding bulk requests we expect the peer to give us. +* If the peer asks for more than this, VCHI will fail and assert. +* The number is determined by the peer's hardware +* - it's the number of outstanding requests that can be queued +* on all bulk channels. VC3's MPHI peripheral allows 16. +*/ #ifndef VCHI_MAX_PEER_BULK_REQUESTS # define VCHI_MAX_PEER_BULK_REQUESTS 32#endif -/* Define VCHI_CCP2TX_MANUAL_POWER if the host tells us when to turn the CCP2 +/* +* Define VCHI_CCP2TX_MANUAL_POWER if the host tells us when to turn the CCP2 * transmitter on and off. */ /*#define VCHI_CCP2TX_MANUAL_POWER*/ #ifndef VCHI_CCP2TX_MANUAL_POWER -/* Timeout (in milliseconds) for putting the CCP2TX interface into IDLE state. Set -* negative for no IDLE. +/* +* Timeout (in milliseconds) for putting the CCP2TX interface into IDLE state. +* Set negative for no IDLE. */ # ifndef VCHI_CCP2TX_IDLE_TIMEOUT # define VCHI_CCP2TX_IDLE_TIMEOUT 5# endif -/* Timeout (in milliseconds) for putting the CCP2TX interface into OFF state. Set -* negative for no OFF. +/* +* Timeout (in milliseconds) for putting the CCP2TX interface into OFF state. +* Set negative for no OFF. */ # ifndef VCHI_CCP2TX_OFF_TIMEOUT # define VCHI_CCP2TX_OFF_TIMEOUT 1000
Signature · 1 line
2.21.0
Greg KH
maintainerQuoted 7 lines · Jules Irenge
Fix warnings of line over 80 characters.
Issue detected by checkepatch tool.Signed-off-by Jules Irenge <[email protected]>--- .../vc04_services/interface/vchi/vchi_cfg.h | 168 +++++++++++------- 1 file changed, 106 insertions(+), 62 deletions(-)
What changed from v1? Always put that below the --- line.
v3 please?
thanks,
greg k-h