Skip to contentSkip to conversation

arm64: dts: qcom: msm8998: Fixup uart3 gpio config for bluetooth

PATCH Superseded Jeffrey Hugo 2 participants 2 messages Oct 19, 2019 – Oct 21, 2019

Subsystems (3)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm64: dts: qcom: msm8998: Fixup uart3 gpio config for bluetooth

It turns out that the wcn3990 can float the gpio lines during bootup, etc which will result in the uart core thinking there is incoming data. This results in the bluetooth stack getting garbage. By applying a bias to match what wcn3990 would drive, the issue is corrected.

---
 .../boot/dts/qcom/msm8998-clamshell.dtsi      | 31 +++++++++++++++++++
 arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi     | 31 +++++++++++++++++++
 2 files changed, 62 insertions(+)
arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi +31 -0
index ab24d415acc0..7e02cb6c8e07 100644
@@ -74,6 +74,37 @@
 	};
 };
 
+&blsp1_uart3_on {
+	/delete-node/ config;
+
+	pinconf-cts {
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		pins = "gpio47";
+		bias-pull-down;
+	};
+
+	pinconf-rts-tx {
+		/* We'll drive 48 (RFR) and 45 (TX), so no pull */
+		pins = "gpio45", "gpio48";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pinconf-rx {
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		pins = "gpio45";
+		bias-pull-up;
+	};
+};
+
 &dsi0 {
 	status = "okay";
 
arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi +31 -0
index 1a1836ed1052..17f51af5e999 100644
@@ -37,6 +37,37 @@
 	};
 };
 
+&blsp1_uart3_on {
+	/delete-node/ config;
+
+	pinconf-cts {
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		pins = "gpio47";
+		bias-pull-down;
+	};
+
+	pinconf-rts-tx {
+		/* We'll drive 48 (RFR) and 45 (TX), so no pull */
+		pins = "gpio45", "gpio48";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pinconf-rx {
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		pins = "gpio45";
+		bias-pull-up;
+	};
+};
+
 &blsp2_uart1 {
 	status = "okay";
 };
Signature · 1 line
2.17.1
#1 lore raw
Quoted 16 lines · Jeffrey Hugo

It turns out that the wcn3990 can float the gpio lines during bootup, etc which will result in the uart core thinking there is incoming data. This results in the bluetooth stack getting garbage. By applying a bias to match what wcn3990 would drive, the issue is corrected.

---
 .../boot/dts/qcom/msm8998-clamshell.dtsi      | 31 +++++++++++++++++++
 arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi     | 31 +++++++++++++++++++
 2 files changed, 62 insertions(+)
arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi +0 -0
index ab24d415acc0..7e02cb6c8e07 100644

arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi line 78

Quoted 5 lines
arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi +2 -0
@@ -74,6 +74,37 @@
 	};
 };
 
+&blsp1_uart3_on {
+	/delete-node/ config;

So it would make much more sense then to split &blsp1_uart3_on in sections defining its pins, than the "logical" config and mux split.

Please send a patch that changes msm8998-pins.dtsi to be:

blsp_uart3_on: blsp1-uart3-on {
	ctx {
	};

	rts {
	};

	rx [
	};

	tx {
	};
};

There's no need for the "pinconf" part and for pinctrl states with a single pin/group we can simply omit the subnode (as this is now possible).

Apart from that, I think this looks good!

Regards,
Bjorn

Quoted 77 lines
arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi +29 -0
+
+	pinconf-cts {
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		pins = "gpio47";
+		bias-pull-down;
+	};
+
+	pinconf-rts-tx {
+		/* We'll drive 48 (RFR) and 45 (TX), so no pull */
+		pins = "gpio45", "gpio48";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pinconf-rx {
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		pins = "gpio45";
+		bias-pull-up;
+	};
+};
+
 &dsi0 {
 	status = "okay";
 
arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi +31 -0
index 1a1836ed1052..17f51af5e999 100644
@@ -37,6 +37,37 @@
 	};
 };
 
+&blsp1_uart3_on {
+	/delete-node/ config;
+
+	pinconf-cts {
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		pins = "gpio47";
+		bias-pull-down;
+	};
+
+	pinconf-rts-tx {
+		/* We'll drive 48 (RFR) and 45 (TX), so no pull */
+		pins = "gpio45", "gpio48";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pinconf-rx {
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		pins = "gpio45";
+		bias-pull-up;
+	};
+};
+
 &blsp2_uart1 {
 	status = "okay";
 };
Signature · 1 line
2.17.1