usb: cdns3: Add TI wrapper
v2 cover usb: cdns3: Add TI wrapper
Hi,
Texas Instruments SoCs have a wrapper module around the Cadence USB3 core. It takes care of clocking and powering the core and providing initial configuration to the core.
This series adds the driver for the TI wrapper and associated DT binding document. This is for -next kernel. Thanks.
cheers,
-roger
Changelog:
v2:
- dt-binding fixes to address Rob's comments
- convert dt-binding document name to DT schema
- get rid of bootstrap properties
- fix DT example
Roger Quadros (2):
dt-bindings: usb: Add binding for the TI wrapper for Cadence USB3
controller
usb: cdns3: Add TI specific wrapper driver
.../devicetree/bindings/usb/ti,j721e-usb.txt | 52 ++++ drivers/usb/cdns3/Kconfig | 10 + drivers/usb/cdns3/Makefile | 1 + drivers/usb/cdns3/cdns3-ti.c | 236 ++++++++++++++++++ 4 files changed, 299 insertions(+) create mode 100644 Documentation/devicetree/bindings/usb/ti,j721e-usb.txt create mode 100644 drivers/usb/cdns3/cdns3-ti.c
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
PATCH v2 1/2 dt-bindings: usb: Add binding for the TI wrapper for Cadence USB3 controller
TI platforms have a wrapper module around the Cadence USB3 controller. Add binding information for that.
--- .../devicetree/bindings/usb/ti,j721e-usb.txt | 52 +++++++++++++++++++ 1 file changed, 52 insertions(+) create mode 100644 Documentation/devicetree/bindings/usb/ti,j721e-usb.txt
Documentation/devicetree/bindings/usb/ti,j721e-usb.txt new file +52 -0
@@ -0,0 +1,52 @@ +Binding for the TI specific wrapper for the Cadence USBSS-DRD controller + +Required properties: + - compatible: Should contain "ti,j721e-usb" + - reg: Physical base address and size of the wrappers register area. + - power-domains: Should contain a phandle to a PM domain provider node + and an args specifier containing the USB device id + value. This property is as per the binding documentation: + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt + - clocks: Clock phandles to usb2_refclk and lpm_clk + - clock-names: Should contain "ref" and "lpm" + +Optional properties: + - ti,usb2-only: If present, it restricts the controller to USB2.0 mode of + operation. Must be present if USB3 PHY is not available + for USB. + - ti,vbus-divider: Should be present if USB VBUS line is connected to the + VBUS pin of the SoC via a 1/3 voltage divider. + +Sub-nodes: +The USB2 PHY and the Cadence USB3 controller should be the sub-nodes. + +Example: + + ti_usb0: cdns_usb@4104000 { + compatible = "ti,j721e-usb"; + reg = <0x00 0x4104000 0x00 0x100>; + power-domains = <&k3_pds 288 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 288 15>, <&k3_clks 288 3>; + clock-names = "ref", "lpm"; + assigned-clocks = <&k3_clks 288 15>; /* USB2_REFCLK */ + assigned-clock-parents = <&k3_clks 288 16>; /* HFOSC0 */ + #address-cells = <2>; + #size-cells = <2>; + ranges; + + usb0: usb@6000000 { + compatible = "cdns,usb3"; + reg = <0x00 0x6000000 0x00 0x10000>, + <0x00 0x6010000 0x00 0x10000>, + <0x00 0x6020000 0x00 0x10000>; + reg-names = "otg", "xhci", "dev"; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, /* irq.6 */ + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; /* otgirq.0 */ + interrupt-names = "host", + "peripheral", + "otg"; + maximum-speed = "super-speed"; + dr_mode = "otg"; + }; + };
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Re: [PATCH v2 1/2] dt-bindings: usb: Add binding for the TI wrapper for Cadence USB3 controller
Hi,
Quoted 2 lines · Roger Quadros
TI platforms have a wrapper module around the Cadence USB3 controller. Add binding information for that.
Please ignore this. I missed converting this to yaml format. Will send v3.
cheers,
-roger
Quoted 68 lines
Cc Rob Herring <[email protected]>Signed-off-by Roger Quadros <[email protected]>Signed-off-by Sekhar Nori <[email protected]>--- .../devicetree/bindings/usb/ti,j721e-usb.txt | 52 +++++++++++++++++++ 1 file changed, 52 insertions(+)create mode 100644
Documentation/devicetree/bindings/usb/ti,j721e-usb.txtDocumentation/devicetree/bindings/usb/ti,j721e-usb.txt new file +52
-0@@ -0,0 +1,52 @@ +Binding for the TI specific wrapper for the Cadence USBSS-DRD controller + +Required properties: + - compatible: Should contain "ti,j721e-usb" + - reg: Physical base address and size of the wrappers register area. + - power-domains: Should contain a phandle to a PM domain provider node + and an args specifier containing the USB device id + value. This property is as per the binding documentation: + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt + - clocks: Clock phandles to usb2_refclk and lpm_clk + - clock-names: Should contain "ref" and "lpm" + +Optional properties: + - ti,usb2-only: If present, it restricts the controller to USB2.0 mode of + operation. Must be present if USB3 PHY is not available + for USB. + - ti,vbus-divider: Should be present if USB VBUS line is connected to the + VBUS pin of the SoC via a 1/3 voltage divider. + +Sub-nodes: +The USB2 PHY and the Cadence USB3 controller should be the sub-nodes. + +Example: + + ti_usb0: cdns_usb@4104000 { + compatible = "ti,j721e-usb"; + reg = <0x00 0x4104000 0x00 0x100>; + power-domains = <&k3_pds 288 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 288 15>, <&k3_clks 288 3>; + clock-names = "ref", "lpm"; + assigned-clocks = <&k3_clks 288 15>; /* USB2_REFCLK */ + assigned-clock-parents = <&k3_clks 288 16>; /* HFOSC0 */ + #address-cells = <2>; + #size-cells = <2>; + ranges; + + usb0: usb@6000000 { + compatible = "cdns,usb3"; + reg = <0x00 0x6000000 0x00 0x10000>, + <0x00 0x6010000 0x00 0x10000>, + <0x00 0x6020000 0x00 0x10000>; + reg-names = "otg", "xhci", "dev"; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, /* irq.6 */ + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; /* otgirq.0 */ + interrupt-names = "host", + "peripheral", + "otg"; + maximum-speed = "super-speed"; + dr_mode = "otg"; + }; + };
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
PATCH v2 2/2 usb: cdns3: Add TI specific wrapper driver
In reply to Roger QuadrosThe J721e platform comes with 2 Cadence USB3 controller instances. This driver supports the TI specific wrapper on this platform.
--- drivers/usb/cdns3/Kconfig | 10 ++ drivers/usb/cdns3/Makefile | 1 + drivers/usb/cdns3/cdns3-ti.c | 236 +++++++++++++++++++++++++++++++++++ 3 files changed, 247 insertions(+) create mode 100644 drivers/usb/cdns3/cdns3-ti.c
drivers/usb/cdns3/Kconfig +10 -0
@@ -43,4 +43,14 @@ config USB_CDNS3_PCI_WRAP If you choose to build this driver as module it will be dynamically linked and module will be called cdns3-pci.ko +config USB_CDNS3_TI + tristate "Cadence USB3 support on TI platforms" + depends on ARCH_K3 || COMPILE_TEST + default USB_CDNS3 + help + Say 'Y' or 'M' here if you are building for Texas Instruments + platforms that contain Cadence USB3 controller core. + + e.g. J721e. + endif
drivers/usb/cdns3/Makefile +1 -0
@@ -14,3 +14,4 @@ endif cdns3-$(CONFIG_USB_CDNS3_HOST) += host.o obj-$(CONFIG_USB_CDNS3_PCI_WRAP) += cdns3-pci-wrap.o +obj-$(CONFIG_USB_CDNS3_TI) += cdns3-ti.o
drivers/usb/cdns3/cdns3-ti.c new file +236 -0
236 lines not on this page · raw message
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Re: [PATCH v2 2/2] usb: cdns3: Add TI specific wrapper driver
Quoted 47 lines · Roger Quadros
The J721e platform comes with 2 Cadence USB3 controller instances. This driver supports the TI specific wrapper on this platform.
Signed-off-by Roger Quadros <[email protected]>Signed-off-by Sekhar Nori <[email protected]>--- drivers/usb/cdns3/Kconfig | 10 ++ drivers/usb/cdns3/Makefile | 1 + drivers/usb/cdns3/cdns3-ti.c | 236 +++++++++++++++++++++++++++++++++++ 3 files changed, 247 insertions(+) create mode 100644 drivers/usb/cdns3/cdns3-ti.cdrivers/usb/cdns3/Kconfig +10
-0@@ -43,4 +43,14 @@ config USB_CDNS3_PCI_WRAP If you choose to build this driver as module it will be dynamically linked and module will be called cdns3-pci.ko +config USB_CDNS3_TI + tristate "Cadence USB3 support on TI platforms" + depends on ARCH_K3 || COMPILE_TEST + default USB_CDNS3 + help + Say 'Y' or 'M' here if you are building for Texas Instruments + platforms that contain Cadence USB3 controller core. + + e.g. J721e. + endifdrivers/usb/cdns3/Makefile +1
-0@@ -14,3 +14,4 @@ endif cdns3-$(CONFIG_USB_CDNS3_HOST) += host.o obj-$(CONFIG_USB_CDNS3_PCI_WRAP) += cdns3-pci-wrap.o +obj-$(CONFIG_USB_CDNS3_TI) += cdns3-ti.odrivers/usb/cdns3/cdns3-ti.c new file +0
-0
drivers/usb/cdns3/cdns3-ti.c line 3
Quoted 3 lines
drivers/usb/cdns3/cdns3-ti.c new file +3
-0@@ -0,0 +1,236 @@ +// SPDX-License-Identifier: GPL-2.0 +/** +* cdns_ti-ti.c - TI specific Glue layer for Cadence USB Controller
cdns3-ti.c
Quoted 129 lines
drivers/usb/cdns3/cdns3-ti.c new file +129
-0+* +* Copyright (C) 2019 Texas Instruments Incorporated - https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.ti.com&data=02%7C01%7Cpeter.chen%40nxp.com%7C94aad23d5a294c5cdaf808d75628931c%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637072604595033025&sdata=Lye5SayAKcqAMaNGbZ%2Fq5OkUZ8IsWMVgGmeh8IhA69M%3D&reserved=0 +*/ + +#include <linux/bits.h> +#include <linux/clk.h> +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> +#include <linux/io.h> +#include <linux/of_platform.h> +#include <linux/pm_runtime.h> + +/* USB Wrapper register offsets */ +#define USBSS_PID 0x0 +#define USBSS_W1 0x4 +#define USBSS_STATIC_CONFIG 0x8 +#define USBSS_PHY_TEST 0xc +#define USBSS_DEBUG_CTRL 0x10 +#define USBSS_DEBUG_INFO 0x14 +#define USBSS_DEBUG_LINK_STATE 0x18 +#define USBSS_DEVICE_CTRL 0x1c + +/* Wrapper 1 register bits */ +#define USBSS_W1_PWRUP_RST BIT(0) +#define USBSS_W1_OVERCURRENT_SEL BIT(8) +#define USBSS_W1_MODESTRAP_SEL BIT(9) +#define USBSS_W1_OVERCURRENT BIT(16) +#define USBSS_W1_MODESTRAP_MASK GENMASK(18, 17) +#define USBSS_W1_MODESTRAP_SHIFT 17 +#define USBSS_W1_USB2_ONLY BIT(19) + +/* Static config register bits */ +#define USBSS1_STATIC_PLL_REF_SEL_MASK GENMASK(8, 5) +#define USBSS1_STATIC_PLL_REF_SEL_SHIFT 5 +#define USBSS1_STATIC_LOOPBACK_MODE_MASK GENMASK(4, 3) +#define USBSS1_STATIC_LOOPBACK_MODE_SHIFT 3 +#define USBSS1_STATIC_VBUS_SEL_MASK GENMASK(2, 1) +#define USBSS1_STATIC_VBUS_SEL_SHIFT 1 +#define USBSS1_STATIC_LANE_REVERSE BIT(0) + +/* Modestrap modes */ +enum modestrap_mode {USBSS_MODESTRAP_MODE_NONE , +USBSS_MODESTRAP_MODE_HOST , +USBSS_MODESTRAP_MODE_PERIPHERAL }; + +struct cdns_ti { +struct device *dev; +void __iomem *usbss; +int usb2_only:1 ; +int vbus_divider:1 ; +struct clk *usb2_refclk; +struct clk *lpm_clk; +}; + +static const int cdns_ti_rate_table[] = {/* in KHZ */ +9600 , +10000 , +12000 , +19200 , +20000 , +24000 , +25000 , +26000 , +38400 , +40000 , +58000 , +50000 , +52000 , +}; + +static inline u32 cdns_ti_readl (struct cdns_ti *data,u32 offset) +{ +return readl (data->usbss + offset); +} + +static inline void cdns_ti_writel (struct cdns_ti *data,u32 offset,u32 value) +{ +writel (value, data->usbss + offset); +} + +static int cdns_ti_probe (struct platform_device *pdev) +{ +struct device *dev = &pdev->dev; +struct device_node *node = pdev->dev.of_node; +struct cdns_ti *data; +struct resource *res; +int error; +u32 reg; +int rate_code, i; +unsigned long rate; + + data =devm_kzalloc (dev,sizeof (*data),GFP_KERNEL ); +if (!data) +return -ENOMEM ; + +platform_set_drvdata (pdev, data); + + data->dev = dev; + + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + data->usbss =devm_ioremap_resource (dev, res); +if (IS_ERR (data->usbss)) +return PTR_ERR (data->usbss); + + data->usb2_refclk =devm_clk_get (dev,"ref" ); +if (IS_ERR (data->usb2_refclk)) { +dev_err (dev,"can't get usb2_refclk\n" ); +return PTR_ERR (data->usb2_refclk); + } + + data->lpm_clk =devm_clk_get (dev,"lpm" ); +if (IS_ERR (data->lpm_clk)) { +dev_err (dev,"can't get lpm_clk\n" ); +return PTR_ERR (data->lpm_clk); + } + + rate =clk_get_rate (data->usb2_refclk); + rate /=1000 ;/* To KHz */ +for (i =0 ; i <ARRAY_SIZE (cdns_ti_rate_table); i++) { +if (cdns_ti_rate_table[i] == rate) +break ; + } + +if (i ==ARRAY_SIZE (cdns_ti_rate_table)) { +dev_err (dev,"unsupported usb2_refclk rate: %lu KHz\n" , rate); +return -EINVAL ;
drivers/usb/cdns3/cdns3-ti.c line 142
Quoted 10 lines
drivers/usb/cdns3/cdns3-ti.c new file +10
-0+ } + + rate_code = i; + +pm_runtime_enable (dev); + error =pm_runtime_get_sync (dev); +if (error <0 ) { +dev_err (dev,"pm_runtime_get_sync failed: %d\n" , error); + goto err_get; + }
Why you don't enable runtime pm at the end of probe?
Peter
Quoted 98 lines
drivers/usb/cdns3/cdns3-ti.c new file +94
-0+ +/* assert RESET */ + reg =cdns_ti_readl (data,USBSS_W1 ); + reg &= ~USBSS_W1_PWRUP_RST ; +cdns_ti_writel (data,USBSS_W1 , reg); + +/* set static config */ + reg =cdns_ti_readl (data,USBSS_STATIC_CONFIG ); + reg &= ~USBSS1_STATIC_PLL_REF_SEL_MASK ; + reg |= rate_code <<USBSS1_STATIC_PLL_REF_SEL_SHIFT ; + + reg &= ~USBSS1_STATIC_VBUS_SEL_MASK ; + data->vbus_divider =device_property_read_bool (dev,"ti,vbus-divider" ); +if (data->vbus_divider) + reg |=1 <<USBSS1_STATIC_VBUS_SEL_SHIFT ; + +cdns_ti_writel (data,USBSS_STATIC_CONFIG , reg); + reg =cdns_ti_readl (data,USBSS_STATIC_CONFIG ); + +/* set USB2_ONLY mode if requested */ + reg =cdns_ti_readl (data,USBSS_W1 ); + data->usb2_only =device_property_read_bool (dev,"ti,usb2-only" ); +if (data->usb2_only) + reg |=USBSS_W1_USB2_ONLY ; + +/* set default modestrap */ + reg |=USBSS_W1_MODESTRAP_SEL ; + reg &= ~USBSS_W1_MODESTRAP_MASK ; + reg |=USBSS_MODESTRAP_MODE_NONE <<USBSS_W1_MODESTRAP_SHIFT ; +cdns_ti_writel (data,USBSS_W1 , reg); + +/* de-assert RESET */ + reg |=USBSS_W1_PWRUP_RST ; +cdns_ti_writel (data,USBSS_W1 , reg); + + error =of_platform_populate (node,NULL ,NULL , dev); +if (error) { +dev_err (dev,"failed to create children: %d\n" , error); + goto err; + } + +return 0 ; + +err: +pm_runtime_put_sync (data->dev); +err_get: +pm_runtime_disable (data->dev); + +return error; +} + +static int cdns_ti_remove_core (struct device *dev,void *c) +{ +struct platform_device *pdev =to_platform_device (dev); + +platform_device_unregister (pdev); + +return 0 ; +} + +static int cdns_ti_remove (struct platform_device *pdev) +{ +struct device *dev = &pdev->dev; + +device_for_each_child (dev,NULL , cdns_ti_remove_core); +pm_runtime_put_sync (dev); +pm_runtime_disable (dev); + +platform_set_drvdata (pdev,NULL ); + +return 0 ; +} + +static const struct of_device_id cdns_ti_of_match[] = { + { .compatible ="ti,j721e-usb" , }, + {}, +}; +MODULE_DEVICE_TABLE (of, cdns_ti_of_match); + +static struct platform_driver cdns_ti_driver = { + .probe = cdns_ti_probe, + .remove = cdns_ti_remove, + .driver = { + .name ="cdns3-ti" , + .of_match_table = cdns_ti_of_match, + }, +}; + +module_platform_driver (cdns_ti_driver); + +MODULE_ALIAS ("platform:cdns3-ti" ); +MODULE_AUTHOR ("Roger Quadros <[email protected]>" ); +MODULE_LICENSE ("GPL v2" ); +MODULE_DESCRIPTION ("Cadence USB3 TI Glue Layer" );Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Signature · 2 lines
Thanks, Peter Chen
Re: [PATCH v2 2/2] usb: cdns3: Add TI specific wrapper driver
Hi Peter,
Quoted 187 lines · Peter Chen
Quoted 47 lines · Roger Quadros
The J721e platform comes with 2 Cadence USB3 controller instances. This driver supports the TI specific wrapper on this platform.
Signed-off-by Roger Quadros <[email protected]>Signed-off-by Sekhar Nori <[email protected]>--- drivers/usb/cdns3/Kconfig | 10 ++ drivers/usb/cdns3/Makefile | 1 + drivers/usb/cdns3/cdns3-ti.c | 236 +++++++++++++++++++++++++++++++++++ 3 files changed, 247 insertions(+)create mode 100644
drivers/usb/cdns3/cdns3-ti.cdrivers/usb/cdns3/Kconfig +10
-0@@ -43,4 +43,14 @@ config USB_CDNS3_PCI_WRAP If you choose to build this driver as module it will be dynamically linked and module will be called cdns3-pci.ko +config USB_CDNS3_TI + tristate "Cadence USB3 support on TI platforms" + depends on ARCH_K3 || COMPILE_TEST + default USB_CDNS3 + help + Say 'Y' or 'M' here if you are building for Texas Instruments + platforms that contain Cadence USB3 controller core. + + e.g. J721e. + endifdrivers/usb/cdns3/Makefile +1
-0@@ -14,3 +14,4 @@ endif cdns3-$(CONFIG_USB_CDNS3_HOST) += host.o obj-$(CONFIG_USB_CDNS3_PCI_WRAP) += cdns3-pci-wrap.o +obj-$(CONFIG_USB_CDNS3_TI) += cdns3-ti.odrivers/usb/cdns3/cdns3-ti.c new file +0
-0drivers/usb/cdns3/cdns3-ti.c line 3
Quoted 3 lines
drivers/usb/cdns3/cdns3-ti.c new file +3
-0@@ -0,0 +1,236 @@ +// SPDX-License-Identifier: GPL-2.0 +/** +* cdns_ti-ti.c - TI specific Glue layer for Cadence USB Controller
cdns3-ti.cQuoted 133 lines
drivers/usb/cdns3/cdns3-ti.c new file +133
-0+* +* Copyright (C) 2019 Texas Instruments Incorporated - https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.ti.com&data=02%7C01%7Cpeter.chen%40nxp.com%7C94aad23d5a294c5cdaf808d75628931c%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637072604595033025&sdata=Lye5SayAKcqAMaNGbZ%2Fq5OkUZ8IsWMVgGmeh8IhA69M%3D&reserved=0 +*/ + +#include <linux/bits.h> +#include <linux/clk.h> +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> +#include <linux/io.h> +#include <linux/of_platform.h> +#include <linux/pm_runtime.h> + +/* USB Wrapper register offsets */ +#define USBSS_PID 0x0 +#define USBSS_W1 0x4 +#define USBSS_STATIC_CONFIG 0x8 +#define USBSS_PHY_TEST 0xc +#define USBSS_DEBUG_CTRL 0x10 +#define USBSS_DEBUG_INFO 0x14 +#define USBSS_DEBUG_LINK_STATE 0x18 +#define USBSS_DEVICE_CTRL 0x1c + +/* Wrapper 1 register bits */ +#define USBSS_W1_PWRUP_RST BIT(0) +#define USBSS_W1_OVERCURRENT_SEL BIT(8) +#define USBSS_W1_MODESTRAP_SEL BIT(9) +#define USBSS_W1_OVERCURRENT BIT(16) +#define USBSS_W1_MODESTRAP_MASK GENMASK(18, 17) +#define USBSS_W1_MODESTRAP_SHIFT 17 +#define USBSS_W1_USB2_ONLY BIT(19) + +/* Static config register bits */ +#define USBSS1_STATIC_PLL_REF_SEL_MASK GENMASK(8, 5) +#define USBSS1_STATIC_PLL_REF_SEL_SHIFT 5 +#define USBSS1_STATIC_LOOPBACK_MODE_MASK GENMASK(4, 3) +#define USBSS1_STATIC_LOOPBACK_MODE_SHIFT 3 +#define USBSS1_STATIC_VBUS_SEL_MASK GENMASK(2, 1) +#define USBSS1_STATIC_VBUS_SEL_SHIFT 1 +#define USBSS1_STATIC_LANE_REVERSE BIT(0) + +/* Modestrap modes */ +enum modestrap_mode {USBSS_MODESTRAP_MODE_NONE , +USBSS_MODESTRAP_MODE_HOST , +USBSS_MODESTRAP_MODE_PERIPHERAL }; + +struct cdns_ti { +struct device *dev; +void __iomem *usbss; +int usb2_only:1 ; +int vbus_divider:1 ; +struct clk *usb2_refclk; +struct clk *lpm_clk; +}; + +static const int cdns_ti_rate_table[] = {/* in KHZ */ +9600 , +10000 , +12000 , +19200 , +20000 , +24000 , +25000 , +26000 , +38400 , +40000 , +58000 , +50000 , +52000 , +}; + +static inline u32 cdns_ti_readl (struct cdns_ti *data,u32 offset) +{ +return readl (data->usbss + offset); +} + +static inline void cdns_ti_writel (struct cdns_ti *data,u32 offset,u32 value) +{ +writel (value, data->usbss + offset); +} + +static int cdns_ti_probe (struct platform_device *pdev) +{ +struct device *dev = &pdev->dev; +struct device_node *node = pdev->dev.of_node; +struct cdns_ti *data; +struct resource *res; +int error; +u32 reg; +int rate_code, i; +unsigned long rate; + + data =devm_kzalloc (dev,sizeof (*data),GFP_KERNEL ); +if (!data) +return -ENOMEM ; + +platform_set_drvdata (pdev, data); + + data->dev = dev; + + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + data->usbss =devm_ioremap_resource (dev, res); +if (IS_ERR (data->usbss)) +return PTR_ERR (data->usbss); + + data->usb2_refclk =devm_clk_get (dev,"ref" ); +if (IS_ERR (data->usb2_refclk)) { +dev_err (dev,"can't get usb2_refclk\n" ); +return PTR_ERR (data->usb2_refclk); + } + + data->lpm_clk =devm_clk_get (dev,"lpm" ); +if (IS_ERR (data->lpm_clk)) { +dev_err (dev,"can't get lpm_clk\n" ); +return PTR_ERR (data->lpm_clk); + } + + rate =clk_get_rate (data->usb2_refclk); + rate /=1000 ;/* To KHz */ +for (i =0 ; i <ARRAY_SIZE (cdns_ti_rate_table); i++) { +if (cdns_ti_rate_table[i] == rate) +break ; + } + +if (i ==ARRAY_SIZE (cdns_ti_rate_table)) { +dev_err (dev,"unsupported usb2_refclk rate: %lu KHz\n" , rate); +return -EINVAL ; + } + + rate_code = i; +
Quoted 8 lines
drivers/usb/cdns3/cdns3-ti.c line 142
Quoted 6 lines
drivers/usb/cdns3/cdns3-ti.c new file +6
-0+pm_runtime_enable (dev); + error =pm_runtime_get_sync (dev); +if (error <0 ) { +dev_err (dev,"pm_runtime_get_sync failed: %d\n" , error); + goto err_get; + }Why you don't enable runtime pm at the end of probe?
Because on our platform that is required to enable the module before the registers can be read.
cheers,
-roger
Quoted 102 lines
Peter
Quoted 98 lines
drivers/usb/cdns3/cdns3-ti.c new file +94
-0+ +/* assert RESET */ + reg =cdns_ti_readl (data,USBSS_W1 ); + reg &= ~USBSS_W1_PWRUP_RST ; +cdns_ti_writel (data,USBSS_W1 , reg); + +/* set static config */ + reg =cdns_ti_readl (data,USBSS_STATIC_CONFIG ); + reg &= ~USBSS1_STATIC_PLL_REF_SEL_MASK ; + reg |= rate_code <<USBSS1_STATIC_PLL_REF_SEL_SHIFT ; + + reg &= ~USBSS1_STATIC_VBUS_SEL_MASK ; + data->vbus_divider =device_property_read_bool (dev,"ti,vbus-divider" ); +if (data->vbus_divider) + reg |=1 <<USBSS1_STATIC_VBUS_SEL_SHIFT ; + +cdns_ti_writel (data,USBSS_STATIC_CONFIG , reg); + reg =cdns_ti_readl (data,USBSS_STATIC_CONFIG ); + +/* set USB2_ONLY mode if requested */ + reg =cdns_ti_readl (data,USBSS_W1 ); + data->usb2_only =device_property_read_bool (dev,"ti,usb2-only" ); +if (data->usb2_only) + reg |=USBSS_W1_USB2_ONLY ; + +/* set default modestrap */ + reg |=USBSS_W1_MODESTRAP_SEL ; + reg &= ~USBSS_W1_MODESTRAP_MASK ; + reg |=USBSS_MODESTRAP_MODE_NONE <<USBSS_W1_MODESTRAP_SHIFT ; +cdns_ti_writel (data,USBSS_W1 , reg); + +/* de-assert RESET */ + reg |=USBSS_W1_PWRUP_RST ; +cdns_ti_writel (data,USBSS_W1 , reg); + + error =of_platform_populate (node,NULL ,NULL , dev); +if (error) { +dev_err (dev,"failed to create children: %d\n" , error); + goto err; + } + +return 0 ; + +err: +pm_runtime_put_sync (data->dev); +err_get: +pm_runtime_disable (data->dev); + +return error; +} + +static int cdns_ti_remove_core (struct device *dev,void *c) +{ +struct platform_device *pdev =to_platform_device (dev); + +platform_device_unregister (pdev); + +return 0 ; +} + +static int cdns_ti_remove (struct platform_device *pdev) +{ +struct device *dev = &pdev->dev; + +device_for_each_child (dev,NULL , cdns_ti_remove_core); +pm_runtime_put_sync (dev); +pm_runtime_disable (dev); + +platform_set_drvdata (pdev,NULL ); + +return 0 ; +} + +static const struct of_device_id cdns_ti_of_match[] = { + { .compatible ="ti,j721e-usb" , }, + {}, +}; +MODULE_DEVICE_TABLE (of, cdns_ti_of_match); + +static struct platform_driver cdns_ti_driver = { + .probe = cdns_ti_probe, + .remove = cdns_ti_remove, + .driver = { + .name ="cdns3-ti" , + .of_match_table = cdns_ti_of_match, + }, +}; + +module_platform_driver (cdns_ti_driver); + +MODULE_ALIAS ("platform:cdns3-ti" ); +MODULE_AUTHOR ("Roger Quadros <[email protected]>" ); +MODULE_LICENSE ("GPL v2" ); +MODULE_DESCRIPTION ("Cadence USB3 TI Glue Layer" );Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki