Skip to contentSkip to conversation

J721e: Add HyperBus support

PATCH New Vignesh Raghavendra 2 participants 8 messages Oct 23, 2019 – Oct 24, 2019

Subsystems (2)
lore
Share & tools
lore

Vignesh Raghavendra

author maintainer
#0 lore raw

v3 cover J721e: Add HyperBus support

This series adds support for HyperBus Memory Controller of TI's J721e and AM654 SoCs.

v3:
Rebase onto latest master branch

Vignesh Raghavendra (6):
mtd: cfi_flash: Use CONFIG_SYS_MONITOR_BASE only when defined
mtd: Add TI HyperBus Memory Controller driver
arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node
arm: dts: k3-j721e-som-p0: Add HyperFlash node
configs: j721e_evm.h: Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT
configs: j721e_evm_a72_defconfig: Add HBMC related configs

 arch/arm/dts/k3-j721e-mcu-wakeup.dtsi |  26 +++++++
 arch/arm/dts/k3-j721e-som-p0.dtsi     |  34 +++++++++
 configs/j721e_evm_a72_defconfig       |  12 +++
 drivers/mtd/Kconfig                   |   7 ++
 drivers/mtd/Makefile                  |   1 +
 drivers/mtd/cfi_flash.c               |   6 +-
 drivers/mtd/hbmc-am654.c              | 105 ++++++++++++++++++++++++++
 include/configs/j721e_evm.h           |   3 +
 8 files changed, 192 insertions(+), 2 deletions(-)
 create mode 100644 drivers/mtd/hbmc-am654.c
Signature · 1 line
2.23.0
author maintainer
#1 lore raw

PATCH v3 1/6 mtd: cfi_flash: Use CONFIG_SYS_MONITOR_BASE only when defined

Make use of CONFIG_SYS_MONITOR_BASE only when available to avoid build error when CONFIG_SYS_MONITOR_BASE is not defined.

---
v3: No change
v2: Make macro check consistent as pointed out by Stefan

 drivers/mtd/cfi_flash.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/mtd/cfi_flash.c +4 -2
index c59254c76e3e..0574fa63a44d 100644
@@ -178,7 +178,8 @@ __maybe_weak u64 flash_read64(void *addr)
 /*-----------------------------------------------------------------------
  */
 #if defined(CONFIG_ENV_IS_IN_FLASH) || defined(CONFIG_ENV_ADDR_REDUND) || \
-	(CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE)
+	(defined(CONFIG_SYS_MONITOR_BASE) && \
+	(CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE))
 static flash_info_t *flash_get_info(ulong base)
 {
 	int i;
@@ -2329,7 +2330,8 @@ static void flash_protect_default(void)
 #endif
 
 	/* Monitor protection ON by default */
-#if (CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE) && \
+#if defined(CONFIG_SYS_MONITOR_BASE) && \
+	(CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE) && \
 	(!defined(CONFIG_MONITOR_IS_IN_RAM))
 	flash_protect(FLAG_PROTECT_SET,
 		      CONFIG_SYS_MONITOR_BASE,
Signature · 1 line
2.23.0
author maintainer
#2 lore raw

PATCH v3 2/6 mtd: Add TI HyperBus Memory Controller driver

In reply to Vignesh Raghavendra

AM654/J721e has HyperBus Memory Controller that supports HyperFlash and HyperRAM devices. It provides a memory mapped interface to interact with these devices. Add a driver to support the same.
Driver calibrates the controller, setups up for MMIO access and probes HyperFlash child node.

---
v3: No change
v2: No change

 drivers/mtd/Kconfig      |   7 +++
 drivers/mtd/Makefile     |   1 +
 drivers/mtd/hbmc-am654.c | 105 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 113 insertions(+)
 create mode 100644 drivers/mtd/hbmc-am654.c
drivers/mtd/Kconfig +7 -0
index 0050fb2b9bf1..37f379d47803 100644
@@ -94,6 +94,13 @@ config RENESAS_RPC_HF
 	  This enables access to Hyperflash memory through the Renesas
 	  RCar Gen3 RPC controller.
 
+config HBMC_AM654
+	bool "HyperBus controller driver for AM65x SoC"
+	depends on SYSCON
+	help
+	 This is the driver for HyperBus controller on TI's AM65x and
+	 other SoCs
+
 source "drivers/mtd/nand/Kconfig"
 
 source "drivers/mtd/spi/Kconfig"
drivers/mtd/Makefile +1 -0
index 22ceda93c06d..293079d709aa 100644
@@ -18,5 +18,6 @@ obj-$(CONFIG_FLASH_PIC32) += pic32_flash.o
 obj-$(CONFIG_ST_SMI) += st_smi.o
 obj-$(CONFIG_STM32_FLASH) += stm32_flash.o
 obj-$(CONFIG_RENESAS_RPC_HF) += renesas_rpc_hf.o
+obj-$(CONFIG_HBMC_AM654) += hbmc-am654.o
 
 obj-y += nand/
drivers/mtd/hbmc-am654.c new file +105 -0

105 lines not on this page · raw message

Signature · 1 line
2.23.0
author maintainer
#3 lore raw

PATCH v3 3/6 arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node

In reply to Vignesh Raghavendra

Add DT node for HyperBus Memory Controller in the FSS. On J721e, its not possible to use OSPI0 and HBMC simultaneously as they are muxed within the Flash Subsystem hence disable HBMC by default as keep OSPI enabled. Bootloader will fixup DT when it detects HyperFlash instead of OSPI.

---

v3:
Rebase onto latest master
Increase functional clock frequency to 250MHz
v2: No change

 arch/arm/dts/k3-j721e-mcu-wakeup.dtsi | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
arch/arm/dts/k3-j721e-mcu-wakeup.dtsi +26 -0
index 01a8f4a9908f..14ffee584a88 100644
@@ -118,4 +118,30 @@
 			loczrama = <1>;
 		};
 	};
+
+	fss: fss at 47000000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x47000000 0x0 0x100>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hbmc_mux: hbmc-mux {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4 0x2>; /* HBMC select */
+		};
+
+		hbmc: hyperbus at 47034000 {
+			compatible = "ti,j721e-hbmc", "ti,am654-hbmc";
+			reg = <0x0 0x47034000 0x0 0x100>,
+				<0x5 0x00000000 0x1 0x0000000>;
+			power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			mux-controls = <&hbmc_mux 0>;
+			assigned-clocks = <&k3_clks 102 0>;
+			assigned-clock-rates = <250000000>;
+		};
+	};
 };
Signature · 1 line
2.23.0
author maintainer
#4 lore raw

PATCH v3 4/6 arm: dts: k3-j721e-som-p0: Add HyperFlash node

In reply to Vignesh Raghavendra

J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the same.

---
v3: No change

 arch/arm/dts/k3-j721e-som-p0.dtsi | 34 +++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)
arch/arm/dts/k3-j721e-som-p0.dtsi +34 -0
index 1884fc70148f..1e1519f1c900 100644
@@ -27,3 +27,37 @@
 		};
 	};
 };
+
+&wkup_pmx0 {
+	mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 1) /* (E20) MCU_OSPI0_CLK.MCU_HYPERBUS0_CK */
+			J721E_WKUP_IOPAD(0x4, PIN_OUTPUT, 1) /* (C21) MCU_OSPI0_LBCLKO.MCU_HYPERBUS0_CKn */
+			J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 1) /* (F19) MCU_OSPI0_CSn0.MCU_HYPERBUS0_CSn0 */
+			J721E_WKUP_IOPAD(0x54, PIN_OUTPUT, 3) /* (E22) MCU_OSPI1_CSn1.MCU_HYPERBUS0_CSn1 */
+			J721E_WKUP_IOPAD(0x30, PIN_OUTPUT, 1) /* (E19) MCU_OSPI0_CSn1.MCU_HYPERBUS0_RESETn */
+			J721E_WKUP_IOPAD(0x8, PIN_INPUT, 1) /* (D21) MCU_OSPI0_DQS.MCU_HYPERBUS0_RWDS */
+			J721E_WKUP_IOPAD(0xc, PIN_INPUT, 1) /* (D20) MCU_OSPI0_D0.MCU_HYPERBUS0_DQ0 */
+			J721E_WKUP_IOPAD(0x10, PIN_INPUT, 1) /* (G19) MCU_OSPI0_D1.MCU_HYPERBUS0_DQ1 */
+			J721E_WKUP_IOPAD(0x14, PIN_INPUT, 1) /* (G20) MCU_OSPI0_D2.MCU_HYPERBUS0_DQ2 */
+			J721E_WKUP_IOPAD(0x18, PIN_INPUT, 1) /* (F20) MCU_OSPI0_D3.MCU_HYPERBUS0_DQ3 */
+			J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 1) /* (F21) MCU_OSPI0_D4.MCU_HYPERBUS0_DQ4 */
+			J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (E21) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */
+			J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (B22) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
+			J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (G21) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
+		>;
+	};
+};
+
+&hbmc {
+	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_hpb0_pins_default>;
+	ranges = <0x0 0x0 0x5 0x0 0x4000000>, /* 64MB Flash on CS0 */
+		 <0x1 0x0 0x5 0x4000000 0x800000>; /* 8MB RAM on CS1 */
+
+	flash at 0,0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0x0 0x0 0x4000000>;
+	};
+};
Signature · 1 line
2.23.0
author maintainer
#5 lore raw

PATCH v3 5/6 configs: j721e_evm.h: Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT

In reply to Vignesh Raghavendra

Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT so that number of flash banks are automatically detected by CFI flash driver

---
v3: No change

 include/configs/j721e_evm.h | 3 +++
 1 file changed, 3 insertions(+)
include/configs/j721e_evm.h +3 -0
index dbe226b46d43..8d4040df9bd4 100644
@@ -56,6 +56,9 @@
 #define CONFIG_SYS_BOOTM_LEN		SZ_64M
 #define CONFIG_CQSPI_REF_CLK		133333333
 
+/* HyperFlash related configuration */
+#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
+
 /* U-Boot general configuration */
 #define EXTRA_ENV_J721E_BOARD_SETTINGS					\
 	"default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0"	\
Signature · 1 line
2.23.0
author maintainer
#6 lore raw

PATCH v3 6/6 configs: j721e_evm_a72_defconfig: Add HBMC related configs

In reply to Vignesh Raghavendra

Enable HBMC and HyperFlash in A72 SPL and A72 U-Boot

---
v3: No change

 configs/j721e_evm_a72_defconfig | 12 ++++++++++++
 1 file changed, 12 insertions(+)
configs/j721e_evm_a72_defconfig +12 -0
index 6729e03620c8..f1f4d8af8593 100644
@@ -34,6 +34,7 @@ CONFIG_SPL_YMODEM_SUPPORT=y
 CONFIG_CMD_ASKENV=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
 CONFIG_CMD_REMOTEPROC=y
 CONFIG_CMD_SF=y
 # CONFIG_CMD_SETEXPR is not set
@@ -63,6 +64,15 @@ CONFIG_MISC=y
 CONFIG_DM_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_AM654=y
+CONFIG_MTD=y
+CONFIG_MTD_NOR_FLASH=y
+CONFIG_MTD_DEVICE=y
+CONFIG_FLASH_CFI_DRIVER=y
+CONFIG_CFI_FLASH=y
+CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
+CONFIG_FLASH_CFI_MTD=y
+CONFIG_SYS_FLASH_CFI=y
+CONFIG_HBMC_AM654=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
 CONFIG_SPI_FLASH_STMICRO=y
@@ -85,3 +95,5 @@ CONFIG_SYSRESET=y
 CONFIG_SPL_SYSRESET=y
 CONFIG_SYSRESET_TI_SCI=y
 CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_MTDIDS_DEFAULT="nor0=47040000.spi.0,nor0=47034000.hyperbus"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=47034000.hyperbus:512k(hbmc.tiboot3),2m(hbmc.tispl),4m(hbmc.u-boot),256k(hbmc.env),1m(hbmc.sysfw),- at 8m(hbmc.rootfs)"
Signature · 1 line
2.23.0
#7 lore raw

v3 cover J721e: Add HyperBus support

In reply to Vignesh Raghavendra
Quoted 23 lines · Vignesh Raghavendra

This series adds support for HyperBus Memory Controller of TI's J721e and AM654 SoCs.

v3:
Rebase onto latest master branch

Vignesh Raghavendra (6):
mtd: cfi_flash: Use CONFIG_SYS_MONITOR_BASE only when defined
mtd: Add TI HyperBus Memory Controller driver
arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node
arm: dts: k3-j721e-som-p0: Add HyperFlash node
configs: j721e_evm.h: Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT
configs: j721e_evm_a72_defconfig: Add HBMC related configs

  arch/arm/dts/k3-j721e-mcu-wakeup.dtsi |  26 +++++++
  arch/arm/dts/k3-j721e-som-p0.dtsi     |  34 +++++++++
  configs/j721e_evm_a72_defconfig       |  12 +++
  drivers/mtd/Kconfig                   |   7 ++
  drivers/mtd/Makefile                  |   1 +
  drivers/mtd/cfi_flash.c               |   6 +-
  drivers/mtd/hbmc-am654.c              | 105 ++++++++++++++++++++++++++
  include/configs/j721e_evm.h           |   3 +
  8 files changed, 192 insertions(+), 2 deletions(-)
Quoted 1 line

create mode 100644 drivers/mtd/hbmc-am654.c

All patches:

Applied to u-boot-marvell/master.

Thanks,
Stefan