Skip to contentSkip to conversation

ARM: dts: imx53-qsb: Use DRM bindings for the Seiko 43WVF1G panel

PATCH Applied Fabio Estevam 2 participants 2 messages Oct 24, 2019 – Oct 28, 2019

Subsystems (2)
lore
Share & tools
lore

Fabio Estevam

author reviewer
#0 lore raw

PATCH 1/1 ARM: dts: imx53-qsb: Use DRM bindings for the Seiko 43WVF1G panel

Currently the parallel panel that is supported is the CLAA WVGA panel, which is the one that comes with the i.MX51 Babbage board.

The default parallel panel that goes with the imx53-qsb board is the Seiko 43WVF1G LCD, so switch to the Seiko one.

While at it convert to DRM bindings.

The parallel display still remains disabled as the default display port is the TVE output.

---
 arch/arm/boot/dts/imx53-qsb-common.dtsi | 44 ++++++++++++++-----------
 1 file changed, 24 insertions(+), 20 deletions(-)
arch/arm/boot/dts/imx53-qsb-common.dtsi +24 -20
index f00dda334976..9b4efcd82636 100644
@@ -18,34 +18,28 @@
 
 	display0: disp0 {
 		compatible = "fsl,imx-parallel-display";
-		interface-pix-fmt = "rgb565";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_ipu_disp0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
 		status = "disabled";
-		display-timings {
-			claawvga {
-				native-mode;
-				clock-frequency = <27000000>;
-				hactive = <800>;
-				vactive = <480>;
-				hback-porch = <40>;
-				hfront-porch = <60>;
-				vback-porch = <10>;
-				vfront-porch = <10>;
-				hsync-len = <20>;
-				vsync-len = <10>;
-				hsync-active = <0>;
-				vsync-active = <0>;
-				de-active = <1>;
-				pixelclk-active = <0>;
-			};
-		};
 
-		port {
+		port@0 {
+			reg = <0>;
+
 			display0_in: endpoint {
 				remote-endpoint = <&ipu_di0_disp0>;
 			};
 		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
 	};
 
 	gpio-keys {
@@ -84,6 +78,16 @@
 		};
 	};
 
+	panel {
+		compatible = "sii,43wvf1g";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Applied
#1 lore raw
Quoted 6 lines · Fabio Estevam

Currently the parallel panel that is supported is the CLAA WVGA panel, which is the one that comes with the i.MX51 Babbage board.

The default parallel panel that goes with the imx53-qsb board is the Seiko 43WVF1G LCD, so switch to the Seiko one.

Quoted 6 lines

While at it convert to DRM bindings.

The parallel display still remains disabled as the default display port is the TVE output.

Applied, thanks.

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel