Add support for DFU boot to DRA7-based EVMs
cover Add support for DFU boot to DRA7-based EVMs
The purpose of this series is to provide the SPL with ability to boot u-boot from DFU.
The DRA7x can download the SPL over the USB1 port when configured in the USB peripheral boot mode. Details on how this can be acheived with the EVMs can found here http://www.ti.com/lit/an/sprac33/sprac33.pdf
Once the SPL is loaded, u-boot can be downloaded on the same USB1 port through DFU.
This boot flow has been tested on DRA7-evm, DRA72-evm-rec, DRA71-evm and DRA76-evm
changes since first sent:
- rebased on top of u-boot/master
Faiz Abbas (3):
ARM: dts: dra7: Add usb peripheral nodes in spl
configs: dra7xx_evm: Add Kconfigs for SPL_DFU bootmode
configs: dra7xx_evm: Increase the size of SPL_MULTI_DTB_FIT
arch/arm/dts/dra7-evm-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/dra71-evm-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/dra72-evm-revc-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/dra72-evm-u-boot.dtsi | 23 +++++++++++++++++++++++ arch/arm/dts/dra76-evm-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/omap5-u-boot.dtsi | 1 + configs/dra7xx_evm_defconfig | 8 +++++++- configs/dra7xx_hs_evm_defconfig | 8 +++++++- 8 files changed, 106 insertions(+), 2 deletions(-) create mode 100644 arch/arm/dts/dra72-evm-u-boot.dtsi
Signature · 1 line
2.17.1
PATCH RESEND 1/3 ARM: dts: dra7: Add usb peripheral nodes in spl
From: Faiz Abbas <[email protected]>
Add usb peripheral and usb phy nodes in spl to enable SPL_DFU bootmode.
---
arch/arm/dts/dra7-evm-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/dra71-evm-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/dra72-evm-revc-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/dra72-evm-u-boot.dtsi | 23 +++++++++++++++++++++++ arch/arm/dts/dra76-evm-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/omap5-u-boot.dtsi | 1 + 6 files changed, 92 insertions(+) create mode 100644 arch/arm/dts/dra72-evm-u-boot.dtsi
arch/arm/dts/dra7-evm-u-boot.dtsi +17 -0
@@ -32,3 +32,20 @@ &mmc2_iodelay_hs200_rev20_conf { u-boot,dm-spl; }; + +&omap_dwc3_1 { + u-boot,dm-spl; +}; + +&usb1 { + u-boot,dm-spl; + dr_mode = "peripheral"; +}; + +&usb2_phy1 { + u-boot,dm-spl; +}; + +&usb3_phy1 { + u-boot,dm-spl; +};
arch/arm/dts/dra71-evm-u-boot.dtsi +17 -0
@@ -44,3 +44,20 @@ &mmc2_iodelay_hs200_rev20_conf { u-boot,dm-spl; }; + +&omap_dwc3_1 { + u-boot,dm-spl; +}; + +&usb1 { + u-boot,dm-spl; + dr_mode = "peripheral"; +}; + +&usb2_phy1 { + u-boot,dm-spl; +}; + +&usb3_phy1 { + u-boot,dm-spl; +};
arch/arm/dts/dra72-evm-revc-u-boot.dtsi +17 -0
@@ -44,3 +44,20 @@ &mmc2_iodelay_hs200_rev20_conf { u-boot,dm-spl; }; + +&omap_dwc3_1 { + u-boot,dm-spl; +}; + +&usb1 { + u-boot,dm-spl; + dr_mode = "peripheral"; +}; + +&usb2_phy1 { + u-boot,dm-spl; +}; + +&usb3_phy1 { + u-boot,dm-spl; +};
arch/arm/dts/dra72-evm-u-boot.dtsi new file +23 -0
@@ -0,0 +1,23 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/ + */ + +#include "omap5-u-boot.dtsi" + +&omap_dwc3_1 { + u-boot,dm-spl; +}; + +&usb1 { + u-boot,dm-spl; + dr_mode = "peripheral"; +}; + +&usb2_phy1 { + u-boot,dm-spl; +}; + +&usb3_phy1 { + u-boot,dm-spl; +};
arch/arm/dts/dra76-evm-u-boot.dtsi +17 -0
@@ -24,3 +24,20 @@ &mmc2_iodelay_hs200_conf { u-boot,dm-spl; }; + +&omap_dwc3_1 { + u-boot,dm-spl; +}; + +&usb1 { + u-boot,dm-spl; + dr_mode = "peripheral"; +}; + +&usb2_phy1 { + u-boot,dm-spl; +}; + +&usb3_phy1 { + u-boot,dm-spl; +};
arch/arm/dts/omap5-u-boot.dtsi +1 -0
@@ -22,6 +22,7 @@ ocp2scp at 4a080000 { compatible = "ti,omap-ocp2scp", "simple-bus"; + u-boot,dm-spl; }; ocp2scp at 4a090000 {
Signature · 1 line
2.17.1
PATCH RESEND 1/3 ARM: dts: dra7: Add usb peripheral nodes in spl
Quoted 6 lines · Jean-Jacques Hiblot
From: Faiz Abbas <[email protected]>
Add usb peripheral and usb phy nodes in spl to enable
SPL_DFUbootmode.Signed-off-by Faiz Abbas <[email protected]>Signed-off-by Jean-Jacques Hiblot <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191025/9d2572dd/attachment.sig>
PATCH RESEND 2/3 configs: dra7xx_evm: Add Kconfigs for SPL_DFU bootmode
In reply to Jean-Jacques HiblotFrom: Faiz Abbas <[email protected]>
Enable configs for supporting SPL_DFU bootmode.
---
configs/dra7xx_evm_defconfig | 6 ++++++ configs/dra7xx_hs_evm_defconfig | 6 ++++++ 2 files changed, 12 insertions(+)
configs/dra7xx_evm_defconfig +6 -0
@@ -25,8 +25,11 @@ CONFIG_SPL_SYS_MALLOC_SIMPLE=y CONFIG_SPL_SEPARATE_BSS=y CONFIG_SPL_DMA_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_RAM_SUPPORT=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x40000 +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_DFU=y CONFIG_CMD_SPL=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_NAND=y
@@ -85,6 +88,7 @@ CONFIG_MII=y CONFIG_DRIVER_TI_CPSW=y CONFIG_SPL_PHY=y CONFIG_PIPE3_PHY=y +CONFIG_SPL_PIPE3_PHY=y CONFIG_OMAP_USB2_PHY=y CONFIG_PMIC_PALMAS=y CONFIG_PMIC_LP873X=y
@@ -107,7 +111,9 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_DWC3=y CONFIG_USB_DWC3_GADGET=y +CONFIG_USB_DWC3_OMAP=y CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_DWC3_PHY_OMAP=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" CONFIG_USB_GADGET_VENDOR_NUM=0x0451
configs/dra7xx_hs_evm_defconfig +6 -0
@@ -30,8 +30,11 @@ CONFIG_SPL_SYS_MALLOC_SIMPLE=y CONFIG_SPL_SEPARATE_BSS=y CONFIG_SPL_DMA_SUPPORT=y # CONFIG_SPL_NAND_SUPPORT is not set +CONFIG_SPL_RAM_SUPPORT=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x40000 +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_DFU=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_NAND=y CONFIG_CMD_MTDPARTS=y
@@ -88,6 +91,7 @@ CONFIG_MII=y CONFIG_DRIVER_TI_CPSW=y CONFIG_SPL_PHY=y CONFIG_PIPE3_PHY=y +CONFIG_SPL_PIPE3_PHY=y CONFIG_OMAP_USB2_PHY=y CONFIG_PMIC_PALMAS=y CONFIG_PMIC_LP873X=y
@@ -110,7 +114,9 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_DWC3=y CONFIG_USB_DWC3_GADGET=y +CONFIG_USB_DWC3_OMAP=y CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_DWC3_PHY_OMAP=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" CONFIG_USB_GADGET_VENDOR_NUM=0x0451
Signature · 1 line
2.17.1
PATCH RESEND 2/3 configs: dra7xx_evm: Add Kconfigs for SPL_DFU bootmode
Quoted 6 lines · Jean-Jacques Hiblot
From: Faiz Abbas <[email protected]>
Enable configs for supporting
SPL_DFUbootmode.Signed-off-by Faiz Abbas <[email protected]>Signed-off-by Jean-Jacques Hiblot <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191025/cea49526/attachment.sig>
PATCH RESEND 3/3 configs: dra7xx_evm: Increase the size of SPL_MULTI_DTB_FIT
In reply to Jean-Jacques HiblotFrom: Faiz Abbas <[email protected]>
Expand SPL_MULTI_DTB_FIT to accommodate usb peripheral nodes being added to support SPL_DFU bootmode.
---
configs/dra7xx_evm_defconfig | 2 +- configs/dra7xx_hs_evm_defconfig | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
configs/dra7xx_evm_defconfig +1 -1
@@ -42,7 +42,7 @@ CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="dra7-evm" CONFIG_OF_LIST="dra7-evm dra72-evm dra72-evm-revc dra71-evm dra76-evm" CONFIG_SPL_MULTI_DTB_FIT=y -CONFIG_SPL_MULTI_DTB_FIT_UNCOMPRESS_SZ=0x9000 +CONFIG_SPL_MULTI_DTB_FIT_UNCOMPRESS_SZ=0xA000 CONFIG_OF_SPL_REMOVE_PROPS="clocks clock-names interrupt-parent" # CONFIG_ENV_IS_IN_FAT is not set CONFIG_ENV_IS_IN_MMC=y
configs/dra7xx_hs_evm_defconfig +1 -1
@@ -45,7 +45,7 @@ CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="dra7-evm" CONFIG_OF_LIST="dra7-evm dra72-evm dra72-evm-revc dra71-evm dra76-evm" CONFIG_SPL_MULTI_DTB_FIT=y -CONFIG_SPL_MULTI_DTB_FIT_UNCOMPRESS_SZ=0x9000 +CONFIG_SPL_MULTI_DTB_FIT_UNCOMPRESS_SZ=0xA000 CONFIG_OF_SPL_REMOVE_PROPS="clocks clock-names interrupt-parent" # CONFIG_ENV_IS_IN_FAT is not set CONFIG_ENV_IS_IN_MMC=y
Signature · 1 line
2.17.1
PATCH RESEND 3/3 configs: dra7xx_evm: Increase the size of SPL_MULTI_DTB_FIT
Quoted 8 lines · Jean-Jacques Hiblot
From: Faiz Abbas <[email protected]>
Expand
SPL_MULTI_DTB_FITto accommodate usb peripheral nodes being added to supportSPL_DFUbootmode.Signed-off-by Faiz Abbas <[email protected]>Signed-off-by Jean-Jacques Hiblot <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191025/c2fdd7b8/attachment.sig>