mtd: spinand: fix detection of GD5FxGQ4xA flash
Subsystems (2)
RFC PATCH 1/1 mtd: spinand: fix detection of GD5FxGQ4xA flash
GD5FxGQ4xA didn't follow the SPI spec to keep MISO low while slave is reading, and instead MISO is kept high. As a result, the first byte of id becomes 0xFF.
Since the first byte isn't supposed to be checked at all, this patch just removed that check.
While at it, redo the comment above to better explain what's happening.
---
RFC:
I doubt whether this patch is a proper fix for the underlying problem:
The actual problem is that we have two different implementation of read id
command: One replies immediately after master sending 0x9f and the other need to send 0x9f and an offset byte (found in winbond and early GD flashes.) Current code only works if SPI master is properly implemented (i.e. keep MOSI low while reading.)
I'm wondering if it worths to split the implementation of read_id into two variants and assign corresponding ID tables to each variant, or we could trust all SPI controllers and this fix is sufficient.
drivers/mtd/nand/spi/gigadevice.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/mtd/nand/spi/gigadevice.c +4 -3
@@ -249,13 +249,14 @@ static int gigadevice_spinand_detect(struct spinand_device *spinand)int ret;/* -* Earlier GDF5-series devices (A,E) return [0][MID][DID] -* Later (F) devices return [MID][DID1][DID2] +* Earlier GDF5-series devices (A,E) need sending an extra offset +* byte before replying flash ID, so the first byte is undetermined. +* Later (F) devices don't need that. */ if (id[0 ] ==SPINAND_MFR_GIGADEVICE ) did = (id[1 ] <<8 ) + id[2 ]; -else if (id[0 ] ==0 && id[1 ] ==SPINAND_MFR_GIGADEVICE ) +else if (id[1 ] ==SPINAND_MFR_GIGADEVICE ) did = id[2 ];else return 0 ;
Signature · 1 line
2.21.0
Miquel Raynal
maintainerHello,
Chuanhong Guo <[email protected]> wrote on Wed, 16 Oct 2019 09:38:24 +0800:
Quoted 11 lines
GD5FxGQ4xA didn't follow the SPI spec to keep MISO low while slave is reading, and instead MISO is kept high. As a result, the first byte of id becomes
0xFF.
Since the first byte isn't supposed to be checked at all, this patch just removed that check.While at it, redo the comment above to better explain what's happening.
Fixes cfd93d7c908e ("mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG")Signed-off-by Chuanhong Guo <[email protected]>CC Jeff Kletsky <[email protected]>
Quoted 8 lines
---
RFC:
I doubt whether this patch is a proper fix for the underlying problem:
The actual problem is that we have two different implementation of read id
command: One replies immediately after master sending0x9fand the other need to send0x9fand an offset byte (found in winbond and early GD flashes.) Current code only works if SPI master is properly implemented (i.e. keep MOSI low while reading.)
I am not entirely against the fix, but this is a SPI host controller issue, right? Can you try to fix the controller driver instead?
Thanks,
Miquèl
Hi!
Quoted 23 lines · Miquel Raynal
Hello,
Chuanhong Guo <[email protected]> wrote on Wed, 16 Oct 2019 09:38:24 +0800:
Quoted 17 lines
GD5FxGQ4xA didn't follow the SPI spec to keep MISO low while slave is reading, and instead MISO is kept high. As a result, the first byte of id becomes
0xFF.
Since the first byte isn't supposed to be checked at all, this patch just removed that check.While at it, redo the comment above to better explain what's happening.
Fixes cfd93d7c908e ("mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG")Signed-off-by Chuanhong Guo <[email protected]>CC Jeff Kletsky <[email protected]>---
RFC:
I doubt whether this patch is a proper fix for the underlying problem:
The actual problem is that we have two different implementation of read id
command: One replies immediately after master sending0x9fand the other need to send0x9fand an offset byte (found in winbond and early GD flashes.)
Correction: Only early GigaDevice nand chips uses this implementation. Winbond chips uses a dummy byte instead of an address byte so there's no problem for Winbond chips.
Quoted 5 lines
Quoted 2 lines
Current code only works if SPI master is properly implemented (i.e. keep MOSI low while reading.)
I am not entirely against the fix, but this is a SPI host controller issue, right? Can you try to fix the controller driver instead?
I think this is a spi nand framework issue. GigaDevice uses an unusual READ ID implementation, and as a result, both host controller and chip are reading during the first byte after 0x9f command: chip is reading the address/offset byte and host is expecting the first ID byte. Here lies two problems:
1. According to the sequence diagram in their datasheet, MISO pin is in High-Z state during the 0x9f command and the offset byte, and host could read anything during this time instead of a fixed 0x0 or 0xff byte, so the check of first byte should be removed. This is what this patch is doing.
2. If there's a buggy SPI host controller that didn't keep MOSI low during reading operation, the chip will get 0xff as ID offset, causing the read vendor/device ID to be swapped. I never met such a controller so far, but if there is one, it will be a silicon bug that can't be fixed by software. To fix this one, we'll have to make a second read-id implementation in spi nand framework.
The second problem only exist in theory, so my preference is to apply this patch and fix only the first problem for now.
Regards,
Chuanhong Guo
Quoted 38 lines · On Sun, 3 Nov 2019 20:03:21 +0800 Chuanhong Guo <[email protected]> wrote:
Hi!
Quoted 23 lines · Miquel Raynal
Hello,
Chuanhong Guo <[email protected]> wrote on Wed, 16 Oct 2019 09:38:24 +0800:
Quoted 17 lines
GD5FxGQ4xA didn't follow the SPI spec to keep MISO low while slave is reading, and instead MISO is kept high. As a result, the first byte of id becomes
0xFF.
Since the first byte isn't supposed to be checked at all, this patch just removed that check.While at it, redo the comment above to better explain what's happening.
Fixes cfd93d7c908e ("mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG")Signed-off-by Chuanhong Guo <[email protected]>CC Jeff Kletsky <[email protected]>---
RFC:
I doubt whether this patch is a proper fix for the underlying problem:
The actual problem is that we have two different implementation of read id
command: One replies immediately after master sending0x9fand the other need to send0x9fand an offset byte (found in winbond and early GD flashes.)Correction: Only early GigaDevice nand chips uses this implementation. Winbond chips uses a dummy byte instead of an address byte so there's no problem for Winbond chips.
Quoted 5 lines
Quoted 2 lines
Current code only works if SPI master is properly implemented (i.e. keep MOSI low while reading.)
I am not entirely against the fix, but this is a SPI host controller issue, right? Can you try to fix the controller driver instead?
Quoted 16 lines
I think this is a spi nand framework issue. GigaDevice uses an unusual READ ID implementation, and as a result, both host controller and chip are reading during the first byte after
0x9fcommand: chip is reading the address/offset byte and host is expecting the first ID byte. Here lies two problems:
1. According to the sequence diagram in their datasheet, MISO pin is in High-Z state during the0x9fcommand and the offset byte, and host could read anything during this time instead of a fixed0x0or0xffbyte, so the check of first byte should be removed. This is what this patch is doing.
2. If there's a buggy SPI host controller that didn't keep MOSI low during reading operation, the chip will get0xffas ID offset, causing the read vendor/device ID to be swapped. I never met such a controller so far, but if there is one, it will be a silicon bug that can't be fixed by software. To fix this one, we'll have to make a second read-id implementation in spi nand framework.
I realize how fragile this ID-based detection is when manufacturers decide to not follow the standard READID semantic (one 0x9f command byte followed by 1 or more input cycles encoding the ID). Let's imagine you have a valid manuf ID byte in ID[0], and the device ID (ID[1]) matches the Winbond or Gigadevice manufacturer ID, and ID[3] (extended Device ID byte?) matches a valid Winbond/Gigadevice device ID. If you skip the check on ID[0] you might erroneously detect a Winbond or Gigadevice NAND, while it's actually something else.
Note that I don't really have a solution to make this detection more robust.
Quoted 3 lines
The second problem only exist in theory, so my preference is to apply this patch and fix only the first problem for now.
I think we should fix that problem now. Maybe by doing a 3 steps detection:
1/ READID + ID[]
2/ READID + DUMMY + ID[]
3/ READID + ADDR + ID[]
At each step we would check if the returned ID matches a valid NAND, and if it does, stop there.
Miquel Raynal
maintainerHi Boris,
Boris Brezillon <[email protected]> wrote on Sun, 3 Nov 2019 14:27:41 +0100:
Quoted 77 lines
Quoted 38 lines · On Sun, 3 Nov 2019 20:03:21 +0800 Chuanhong Guo <[email protected]> wrote:
Hi!
Quoted 23 lines · Miquel Raynal
Hello,
Chuanhong Guo <[email protected]> wrote on Wed, 16 Oct 2019 09:38:24 +0800:
Quoted 17 lines
GD5FxGQ4xA didn't follow the SPI spec to keep MISO low while slave is reading, and instead MISO is kept high. As a result, the first byte of id becomes
0xFF.
Since the first byte isn't supposed to be checked at all, this patch just removed that check.While at it, redo the comment above to better explain what's happening.
Fixes cfd93d7c908e ("mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG")Signed-off-by Chuanhong Guo <[email protected]>CC Jeff Kletsky <[email protected]>---
RFC:
I doubt whether this patch is a proper fix for the underlying problem:
The actual problem is that we have two different implementation of read id
command: One replies immediately after master sending0x9fand the other need to send0x9fand an offset byte (found in winbond and early GD flashes.)Correction: Only early GigaDevice nand chips uses this implementation. Winbond chips uses a dummy byte instead of an address byte so there's no problem for Winbond chips.
Quoted 5 lines
Quoted 2 lines
Current code only works if SPI master is properly implemented (i.e. keep MOSI low while reading.)
I am not entirely against the fix, but this is a SPI host controller issue, right? Can you try to fix the controller driver instead?
Quoted 16 lines
I think this is a spi nand framework issue. GigaDevice uses an unusual READ ID implementation, and as a result, both host controller and chip are reading during the first byte after
0x9fcommand: chip is reading the address/offset byte and host is expecting the first ID byte. Here lies two problems:
1. According to the sequence diagram in their datasheet, MISO pin is in High-Z state during the0x9fcommand and the offset byte, and host could read anything during this time instead of a fixed0x0or0xffbyte, so the check of first byte should be removed. This is what this patch is doing.
2. If there's a buggy SPI host controller that didn't keep MOSI low during reading operation, the chip will get0xffas ID offset, causing the read vendor/device ID to be swapped. I never met such a controller so far, but if there is one, it will be a silicon bug that can't be fixed by software. To fix this one, we'll have to make a second read-id implementation in spi nand framework.I realize how fragile this ID-based detection is when manufacturers decide to not follow the standard READID semantic (one
0x9fcommand byte followed by 1 or more input cycles encoding the ID). Let's imagine you have a valid manuf ID byte in ID[0], and the device ID (ID[1]) matches the Winbond or Gigadevice manufacturer ID, and ID[3] (extended Device ID byte?) matches a valid Winbond/Gigadevice device ID. If you skip the check on ID[0] you might erroneously detect a Winbond or Gigadevice NAND, while it's actually something else.Note that I don't really have a solution to make this detection more robust.
Quoted 3 lines
The second problem only exist in theory, so my preference is to apply this patch and fix only the first problem for now.
I think we should fix that problem now. Maybe by doing a 3 steps detection:
Quoted 6 lines
1/ READID + ID[]
2/ READID + DUMMY + ID[]
3/ READID + ADDR + ID[]At each step we would check if the returned ID matches a valid NAND, and if it does, stop there.
I like the idea. That will be way more robust.
Thanks,
Miquèl