Skip to contentSkip to conversation

media: ti-vpe: cal: maintenance

PATCH Superseded Benoit Parrot 2 participants 36 messages Nov 4, 2019 – Nov 12, 2019

Subsystems (3)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover media: ti-vpe: cal: maintenance

This a collection of backlog patches I have been carrying for the CAL driver.

- Add support for SoC variants.

- Switches to syscon/regmap to access a system controller register for the DPHY configuration. This register has different bit layout depending on the SoC version.

- It adds supports for pre ES2.0 silicon errata.

- Reworked the DPHY initialization sequence to match the technical reference manual and provide a more robust restartability.

- Adds the missing ability to power subdevice.

- Update the devicetree binding and then converts it to dt-schema

Changes since v1:
- Removed unneeded "items/max/min".
- Add a ref for ti,camerrx-control type
- Move compatible description as comment in the schemas
- Simplify 'endpoint' syntax
- Removed clocks description
- Added ti,cal.yaml to MAINTAINERS as a separate patch.
- Added Rob's ack
- Remove 'inline' from cal_runtime_get()
- Switch to use of_device_get_match_data
- Reworked the syscon_regmap_lookup_by_phandle() section
- Updated the binding to use ti,camerrx-control instead of sycon_camerrx
- Updated the binding to use ti,camerrx-control instead of sycon_camerrx

Benoit Parrot (19):
dt-bindings: media: cal: update binding to use syscon
dt-bindings: media: cal: update binding example
media: ti-vpe: cal: Add per platform data support
media: ti-vpe: cal: Enable DMABUF export
dt-bindings: media: cal: update binding to add PHY LDO errata support
media: ti-vpe: cal: add CSI2 PHY LDO errata support
media: ti-vpe: cal: Fix ths_term/ths_settle parameters
media: ti-vpe: cal: Fix pixel processing parameters
media: ti-vpe: cal: Align DPHY init sequence with docs
dt-bindings: media: cal: update binding to add DRA76x support
media: ti-vpe: cal: Add DRA76x support
dt-bindings: media: cal: update binding to add AM654 support
media: ti-vpe: cal: Add AM654 support
media: ti-vpe: cal: Add subdev s_power hooks
media: ti-vpe: cal: Properly calculate max resolution boundary
media: ti-vpe: cal: Fix a WARN issued when start streaming fails
media: ti-vpe: cal: fix enum_mbus_code/frame_size subdev arguments
dt-bindings: media: cal: convert binding to yaml
MAINTAINERS: Add ti,cal.yaml

Nikhil Devshatwar (1):
media: ti-vpe: cal: Restrict DMA to avoid memory corruption

 .../devicetree/bindings/media/ti,cal.yaml     | 172 ++++
 .../devicetree/bindings/media/ti-cal.txt      |  72 --
 MAINTAINERS                                   |   1 +
 drivers/media/platform/Kconfig                |   2 +-
 drivers/media/platform/ti-vpe/cal.c           | 767 ++++++++++++++----
 drivers/media/platform/ti-vpe/cal_regs.h      |  27 +
 6 files changed, 808 insertions(+), 233 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/ti,cal.yaml
 delete mode 100644 Documentation/devicetree/bindings/media/ti-cal.txt
Signature · 1 line
2.17.1
#1 lore raw

PATCH v2 1/20 dt-bindings: media: cal: update binding to use syscon

Update Device Tree bindings for the CAL driver to use syscon to access the phy config register instead of trying to map it directly.

---
 Documentation/devicetree/bindings/media/ti-cal.txt | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
Documentation/devicetree/bindings/media/ti-cal.txt +9 -5
index ae9b52f37576..93096d924786 100644
@@ -10,9 +10,14 @@ Required properties:
 - compatible: must be "ti,dra72-cal"
 - reg:	CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX
 	control address space
-- reg-names: cal_top, cal_rx_core0, cal_rx_core1, and camerrx_control
+- reg-names: cal_top, cal_rx_core0, cal_rx_core1 and camerrx_control
 	     registers
 - interrupts: should contain IRQ line for the CAL;
+- ti,camerrx-control: phandle to the device control module and offset to
+		      the control_camerarx_core register.
+		      This node is meant to replace the "camerrx_control"
+		      reg entry above but "camerrx_control" is still
+		      handled for backward compatibility.
 
 CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes
 should contain a 'port' child node with child 'endpoint' node. Please
@@ -25,13 +30,12 @@ Example:
 		ti,hwmods = "cal";
 		reg = <0x4845B000 0x400>,
 		      <0x4845B800 0x40>,
-		      <0x4845B900 0x40>,
-		      <0x4A002e94 0x4>;
+		      <0x4845B900 0x40>;
 		reg-names = "cal_top",
 			    "cal_rx_core0",
-			    "cal_rx_core1",
-			    "camerrx_control";
+			    "cal_rx_core1";
 		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+		ti,camerrx-control = <&scm_conf 0xE94>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
Signature · 1 line
2.17.1
#2 lore raw

PATCH v2 2/20 dt-bindings: media: cal: update binding example

In reply to Benoit Parrot

Update binding example to show proper endpoint properties and linkage.

---
 .../devicetree/bindings/media/ti-cal.txt      | 31 ++++++++++---------
 1 file changed, 16 insertions(+), 15 deletions(-)
Documentation/devicetree/bindings/media/ti-cal.txt +16 -15
index 93096d924786..7e960cf26e23 100644
@@ -27,7 +27,6 @@ Documentation/devicetree/bindings/media/video-interfaces.txt.
 Example:
 	cal: cal@4845b000 {
 		compatible = "ti,dra72-cal";
-		ti,hwmods = "cal";
 		reg = <0x4845B000 0x400>,
 		      <0x4845B800 0x40>,
 		      <0x4845B900 0x40>;
@@ -45,9 +44,10 @@ Example:
 
 			csi2_0: port@0 {
 				reg = <0>;
-				endpoint {
-					slave-mode;
-					remote-endpoint = <&ar0330_1>;
+				csi2_phy0: endpoint {
+					remote-endpoint = <&csi2_cam0>;
+					clock-lanes = <0>;
+					data-lanes = <1 2>;
 				};
 			};
 			csi2_1: port@1 {
@@ -57,19 +57,20 @@ Example:
 	};
 
 	i2c5: i2c@4807c000 {
-		ar0330@10 {
-			compatible = "ti,ar0330";
-			reg = <0x10>;
+		clock-frequency = <400000>;
 
-			port {
-				#address-cells = <1>;
-				#size-cells = <0>;
+		camera-sensor@3c {
+			compatible = "ovti,ov5640";
+			reg = <0x3c>;
+
+			clocks = <&clk_fixed>;
+			clock-names = "xclk";
 
-				ar0330_1: endpoint {
-					reg = <0>;
-					clock-lanes = <1>;
-					data-lanes = <0 2 3 4>;
-					remote-endpoint = <&csi2_0>;
+			port {
+				csi2_cam0: endpoint {
+					remote-endpoint = <&csi2_phy0>;
+					clock-lanes = <0>;
+					data-lanes = <1 2>;
 				};
 			};
 		};
Signature · 1 line
2.17.1
#3 lore raw

PATCH v2 3/20 media: ti-vpe: cal: Add per platform data support

In reply to Benoit Parrot

First this patch adds a method to access the CTRL_CORE_CAMERRX_CONTROL register to use the syscon mechanism. For backward compatibility we also handle using the existing camerrx_control "reg" entry if a syscon node is not found.

In addition the register bit layout for the CTRL_CORE_CAMERRX_CONTROL changes depending on the device. In order to support this we need to use a register access scheme based on data configuration instead of using static macro.

In this case we make use of the regmap facility and create data set based on the various device and phy available.

---
 drivers/media/platform/ti-vpe/cal.c | 271 +++++++++++++++++++++-------
 1 file changed, 202 insertions(+), 69 deletions(-)
drivers/media/platform/ti-vpe/cal.c +202 -69
index 223161f9c403..5d807b8f0f23 100644
@@ -14,6 +14,8 @@
 #include <linux/delay.h>
 #include <linux/pm_runtime.h>
 #include <linux/slab.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
 #include <linux/videodev2.h>
 #include <linux/of_device.h>
 #include <linux/of_graph.h>
@@ -220,20 +222,66 @@ struct cal_dmaqueue {
 	int			ini_jiffies;
 };
 
-struct cm_data {
+struct cc_data {
 	void __iomem		*base;
 	struct resource		*res;
 
-	unsigned int		camerrx_control;
-
 	struct platform_device *pdev;
 };
 
-struct cc_data {
-	void __iomem		*base;
-	struct resource		*res;
+/* CTRL_CORE_CAMERRX_CONTROL register field id */
+enum cal_camerarx_field {
+	F_CTRLCLKEN,
+	F_CAMMODE,
+	F_LANEENABLE,
+	F_CSI_MODE,
 
-	struct platform_device *pdev;
+	F_MAX_FIELDS,
+};
+
+struct cal_csi2_phy {
+	struct regmap_field *fields[F_MAX_FIELDS];
+	struct reg_field *base_fields;
+	const int num_lanes;
+};
+
+struct cal_data {
+	const int num_csi2_phy;
+	struct cal_csi2_phy *csi2_phy_core;
+
+	const unsigned int flags;
+};
+
+static struct reg_field dra72x_ctrl_core_csi0_reg_fields[F_MAX_FIELDS] = {
+	[F_CTRLCLKEN] = REG_FIELD(0, 10, 10),
+	[F_CAMMODE] = REG_FIELD(0, 11, 12),
+	[F_LANEENABLE] = REG_FIELD(0, 13, 16),
+	[F_CSI_MODE] = REG_FIELD(0, 17, 17),
+};
+
+static struct reg_field dra72x_ctrl_core_csi1_reg_fields[F_MAX_FIELDS] = {
+	[F_CTRLCLKEN] = REG_FIELD(0, 0, 0),
+	[F_CAMMODE] = REG_FIELD(0, 1, 2),
+	[F_LANEENABLE] = REG_FIELD(0, 3, 4),
+	[F_CSI_MODE] = REG_FIELD(0, 5, 5),
+};
+
+static struct cal_csi2_phy dra72x_cal_csi_phy[] = {
+	{
+		.base_fields = dra72x_ctrl_core_csi0_reg_fields,
+		.num_lanes = 4,
+	},
+	{
+		.base_fields = dra72x_ctrl_core_csi1_reg_fields,
+		.num_lanes = 2,
+	},
+};
+
+static struct cal_data dra72x_cal_data = {
+	.csi2_phy_core = dra72x_cal_csi_phy,
+	.num_csi2_phy = ARRAY_SIZE(dra72x_cal_csi_phy),
+
+	.flags = 0,
 };
 
 /*
@@ -247,8 +295,15 @@ struct cal_dev {
 	struct platform_device	*pdev;
 	struct v4l2_device	v4l2_dev;
 
+	/* Controller flags for special cases */
+	unsigned int		flags;
+
+	const struct cal_data	*data;
+
 	/* Control Module handle */
-	struct cm_data		*cm;
+	struct regmap		*syscon_camerrx;
+	u32			syscon_camerrx_offset;
+
 	/* Camera Core Module handle */
 	struct cc_data		*cc[CAL_NUM_CSI2_PORTS];
 
@@ -359,73 +414,113 @@ static inline void set_field(u32 *valp, u32 field, u32 mask)
 	*valp = val;
 }
 
-/*
- * Control Module block access
- */
-static struct cm_data *cm_create(struct cal_dev *dev)
+static u32 cal_data_get_phy_max_lanes(struct cal_ctx *ctx)
 {
-	struct platform_device *pdev = dev->pdev;
-	struct cm_data *cm;
+	struct cal_dev *dev = ctx->dev;
+	u32 phy_id = ctx->csi2_port - 1;
 
-	cm = devm_kzalloc(&pdev->dev, sizeof(*cm), GFP_KERNEL);
-	if (!cm)
-		return ERR_PTR(-ENOMEM);
+	return dev->data->csi2_phy_core[phy_id].num_lanes;
+}
+
+static u32 cal_data_get_num_csi2_phy(struct cal_dev *dev)
+{
+	return dev->data->num_csi2_phy;
+}
+
+static int cal_camerarx_regmap_init(struct cal_dev *dev)
+{
+	struct reg_field *field;
+	struct cal_csi2_phy *phy;
+	int i, j;
+
+	if (!dev->data)
+		return -EINVAL;
+
+	for (i = 0; i < cal_data_get_num_csi2_phy(dev); i++) {
+		phy = &dev->data->csi2_phy_core[i];
+		for (j = 0; j < F_MAX_FIELDS; j++) {
+			field = &phy->base_fields[j];
+			/*
+			 * Here we update the reg offset with the
+			 * value found in DT
+			 */
+			field->reg = dev->syscon_camerrx_offset;
+			phy->fields[j] =
+				devm_regmap_field_alloc(&dev->pdev->dev,
+							dev->syscon_camerrx,
+							*field);
+			if (IS_ERR(phy->fields[j])) {
+				cal_err(dev, "Unable to allocate regmap fields\n");
+				return PTR_ERR(phy->fields[j]);
+			}
+		}
+	}
+	return 0;
+}
+
+static const struct regmap_config cal_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+};
 
-	cm->res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-						"camerrx_control");
-	cm->base = devm_ioremap_resource(&pdev->dev, cm->res);
-	if (IS_ERR(cm->base)) {
+static struct regmap *cal_get_camerarx_regmap(struct cal_dev *dev)
+{
+	struct platform_device *pdev = dev->pdev;
+	struct regmap *regmap;
+	void __iomem *base;
+	u32 reg_io_width;
+	struct regmap_config r_config = cal_regmap_config;
+	struct resource *res;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+					   "camerrx_control");
+	base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(base)) {
 		cal_err(dev, "failed to ioremap\n");
-		return ERR_CAST(cm->base);
+		return ERR_CAST(base);
 	}
 
 	cal_dbg(1, dev, "ioresource %s at %pa - %pa\n",
-		cm->res->name, &cm->res->start, &cm->res->end);
+		res->name, &res->start, &res->end);
+
+	reg_io_width = 4;
+	r_config.reg_stride = reg_io_width;
+	r_config.val_bits = reg_io_width * 8;
+	r_config.max_register = resource_size(res) - reg_io_width;
 
-	return cm;
+	regmap = regmap_init_mmio(NULL, base, &r_config);
+	if (IS_ERR(regmap))
+		pr_err("regmap init failed\n");
+
+	return regmap;
 }
 
+/*
+ * Control Module CAMERARX block access
+ */
 static void camerarx_phy_enable(struct cal_ctx *ctx)
 {
-	u32 val;
-
-	if (!ctx->dev->cm->base) {
-		ctx_err(ctx, "cm not mapped\n");
-		return;
-	}
-
-	val = reg_read(ctx->dev->cm, CM_CTRL_CORE_CAMERRX_CONTROL);
-	if (ctx->csi2_port == 1) {
-		set_field(&val, 1, CM_CAMERRX_CTRL_CSI0_CTRLCLKEN_MASK);
-		set_field(&val, 0, CM_CAMERRX_CTRL_CSI0_CAMMODE_MASK);
-		/* enable all lanes by default */
-		set_field(&val, 0xf, CM_CAMERRX_CTRL_CSI0_LANEENABLE_MASK);
-		set_field(&val, 1, CM_CAMERRX_CTRL_CSI0_MODE_MASK);
-	} else if (ctx->csi2_port == 2) {
-		set_field(&val, 1, CM_CAMERRX_CTRL_CSI1_CTRLCLKEN_MASK);
-		set_field(&val, 0, CM_CAMERRX_CTRL_CSI1_CAMMODE_MASK);
-		/* enable all lanes by default */
-		set_field(&val, 0x3, CM_CAMERRX_CTRL_CSI1_LANEENABLE_MASK);
-		set_field(&val, 1, CM_CAMERRX_CTRL_CSI1_MODE_MASK);
-	}
-	reg_write(ctx->dev->cm, CM_CTRL_CORE_CAMERRX_CONTROL, val);
+	struct cal_csi2_phy *phy;
+	u32 phy_id = ctx->csi2_port - 1;
+	u32 max_lanes;
+
+	phy = &ctx->dev->data->csi2_phy_core[phy_id];
+	regmap_field_write(phy->fields[F_CAMMODE], 0);
+	/* Always enable all lanes at the phy control level */
+	max_lanes = (1 << cal_data_get_phy_max_lanes(ctx)) - 1;
+	regmap_field_write(phy->fields[F_LANEENABLE], max_lanes);
+	regmap_field_write(phy->fields[F_CSI_MODE], 1);
+	regmap_field_write(phy->fields[F_CTRLCLKEN], 1);
 }
 
 static void camerarx_phy_disable(struct cal_ctx *ctx)
 {
-	u32 val;
+	struct cal_csi2_phy *phy;
+	u32 phy_id = ctx->csi2_port - 1;
 
-	if (!ctx->dev->cm->base) {
-		ctx_err(ctx, "cm not mapped\n");
-		return;
-	}
-
-	val = reg_read(ctx->dev->cm, CM_CTRL_CORE_CAMERRX_CONTROL);
-	if (ctx->csi2_port == 1)
-		set_field(&val, 0x0, CM_CAMERRX_CTRL_CSI0_CTRLCLKEN_MASK);
-	else if (ctx->csi2_port == 2)
-		set_field(&val, 0x0, CM_CAMERRX_CTRL_CSI1_CTRLCLKEN_MASK);
-	reg_write(ctx->dev->cm, CM_CTRL_CORE_CAMERRX_CONTROL, val);
+	phy = &ctx->dev->data->csi2_phy_core[phy_id];
+	regmap_field_write(phy->fields[F_CTRLCLKEN], 0);
 }
 
 /*
@@ -508,12 +603,6 @@ static void cal_quickdump_regs(struct cal_dev *dev)
 			       resource_size(dev->ctx[1]->cc->res),
 			       false);
 	}
-
-	cal_info(dev, "CAMERRX_Control Registers @ %pa:\n",
-		 &dev->cm->res->start);
-	print_hex_dump(KERN_INFO, "", DUMP_PREFIX_OFFSET, 16, 4,
-		       (__force const void *)dev->cm->base,
-		       resource_size(dev->cm->res), false);
 }
 
 /*
@@ -1804,10 +1893,15 @@ static struct cal_ctx *cal_create_instance(struct cal_dev *dev, int inst)
 	return NULL;
 }
 
+static const struct of_device_id cal_of_match[];
+
 static int cal_probe(struct platform_device *pdev)
 {
 	struct cal_dev *dev;
 	struct cal_ctx *ctx;
+	struct device_node *parent = pdev->dev.of_node;
+	struct regmap *syscon_camerrx = NULL;
+	u32 syscon_camerrx_offset = 0;
 	int ret;
 	int irq;
 	int i;
@@ -1816,6 +1910,14 @@ static int cal_probe(struct platform_device *pdev)
 	if (!dev)
 		return -ENOMEM;
 
+	dev->data = of_device_get_match_data(&pdev->dev);
+	if (!dev->data) {
+		dev_err(&pdev->dev, "Could not get feature data based on compatible version\n");
+		return -ENODEV;
+	}
+
+	dev->flags = dev->data->flags;
+
 	/* set pseudo v4l2 device name so we can use v4l2_printk */
 	strscpy(dev->v4l2_dev.name, CAL_MODULE_NAME,
 		sizeof(dev->v4l2_dev.name));
@@ -1823,6 +1925,38 @@ static int cal_probe(struct platform_device *pdev)
 	/* save pdev pointer */
 	dev->pdev = pdev;
 
+	syscon_camerrx = syscon_regmap_lookup_by_phandle(parent,
+							 "ti,camerrx-control");
+	ret = of_property_read_u32_index(parent, "ti,camerrx-control", 1,
+					 &syscon_camerrx_offset);
+	if (IS_ERR(syscon_camerrx))
+		ret = PTR_ERR(syscon_camerrx);
+	if (ret) {
+		dev_warn(&pdev->dev, "failed to get ti,camerrx-control: %d\n",
+			 ret);
+
+		/*
+		 * Backward DTS compatibility.
+		 * If syscon entry is not present then check if the
+		 * camerrx_control resource is present.
+		 */
+		syscon_camerrx = cal_get_camerarx_regmap(dev);
+		if (IS_ERR(syscon_camerrx)) {
+			dev_err(&pdev->dev, "failed to get camerrx_control regmap\n");
+			return PTR_ERR(syscon_camerrx);
+		}
+		/* In this case the base already point to the direct
+		 * CM register so no need for an offset
+		 */
+		syscon_camerrx_offset = 0;
+	}
+
+	dev->syscon_camerrx = syscon_camerrx;
+	dev->syscon_camerrx_offset = syscon_camerrx_offset;
+	ret = cal_camerarx_regmap_init(dev);
+	if (ret)
+		return ret;
+
 	dev->res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
 						"cal_top");
 	dev->base = devm_ioremap_resource(&pdev->dev, dev->res);
@@ -1841,10 +1975,6 @@ static int cal_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, dev);
 
-	dev->cm = cm_create(dev);
-	if (IS_ERR(dev->cm))
-		return PTR_ERR(dev->cm);
-
 	dev->cc[0] = cc_create(dev, 0);
 	if (IS_ERR(dev->cc[0]))
 		return PTR_ERR(dev->cc[0]);
@@ -1924,7 +2054,10 @@ static int cal_remove(struct platform_device *pdev)
 
 #if defined(CONFIG_OF)
 static const struct of_device_id cal_of_match[] = {
-	{ .compatible = "ti,dra72-cal", },
+	{
+		.compatible = "ti,dra72-cal",
+		.data = (void *)&dra72x_cal_data,
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(of, cal_of_match);
Signature · 1 line
2.17.1
#4 lore raw

PATCH v2 4/20 media: ti-vpe: cal: Enable DMABUF export

In reply to Benoit Parrot

Allow CAL to be able to export DMA buffer.

---
 drivers/media/platform/ti-vpe/cal.c | 1 +
 1 file changed, 1 insertion(+)
drivers/media/platform/ti-vpe/cal.c +1 -0
index 5d807b8f0f23..7d25ad83ca1e 100644
@@ -1488,6 +1488,7 @@ static const struct v4l2_ioctl_ops cal_ioctl_ops = {
 	.vidioc_querybuf      = vb2_ioctl_querybuf,
 	.vidioc_qbuf          = vb2_ioctl_qbuf,
 	.vidioc_dqbuf         = vb2_ioctl_dqbuf,
+	.vidioc_expbuf        = vb2_ioctl_expbuf,
 	.vidioc_enum_input    = cal_enum_input,
 	.vidioc_g_input       = cal_g_input,
 	.vidioc_s_input       = cal_s_input,
Signature · 1 line
2.17.1
#5 lore raw

PATCH v2 5/20 media: ti-vpe: cal: Restrict DMA to avoid memory corruption

In reply to Benoit Parrot

From: Nikhil Devshatwar <[email protected]>

When setting DMA for video capture from CSI channel, if the DMA size is not given, it ends up writing as much data as sent by the camera.

This may lead to overwriting the buffers causing memory corruption. Observed green lines on the default framebuffer.

Restrict the DMA to maximum height as specified in the S_FMT ioctl.

---
 drivers/media/platform/ti-vpe/cal.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/media/platform/ti-vpe/cal.c +4 -2
index 7d25ad83ca1e..04e84c4dc92a 100644
@@ -769,12 +769,13 @@ static void pix_proc_config(struct cal_ctx *ctx)
 }
 
 static void cal_wr_dma_config(struct cal_ctx *ctx,
-			      unsigned int width)
+			      unsigned int width, unsigned int height)
 {
 	u32 val;
 
 	val = reg_read(ctx->dev, CAL_WR_DMA_CTRL(ctx->csi2_port));
 	set_field(&val, ctx->csi2_port, CAL_WR_DMA_CTRL_CPORT_MASK);
+	set_field(&val, height, CAL_WR_DMA_CTRL_YSIZE_MASK);
 	set_field(&val, CAL_WR_DMA_CTRL_DTAG_PIX_DAT,
 		  CAL_WR_DMA_CTRL_DTAG_MASK);
 	set_field(&val, CAL_WR_DMA_CTRL_MODE_CONST,
@@ -1397,7 +1398,8 @@ static int cal_start_streaming(struct vb2_queue *vq, unsigned int count)
 	csi2_lane_config(ctx);
 	csi2_ctx_config(ctx);
 	pix_proc_config(ctx);
-	cal_wr_dma_config(ctx, ctx->v_fmt.fmt.pix.bytesperline);
+	cal_wr_dma_config(ctx, ctx->v_fmt.fmt.pix.bytesperline,
+			  ctx->v_fmt.fmt.pix.height);
 	cal_wr_dma_addr(ctx, addr);
 	csi2_ppi_enable(ctx);
 
Signature · 1 line
2.17.1
#6 lore raw

PATCH v2 6/20 dt-bindings: media: cal: update binding to add PHY LDO errata support

In reply to Benoit Parrot

Update Device Tree bindings for the CAL driver to add support for the CSI2 PHY LDO errata workaround for pre-es2 devices.

---
 Documentation/devicetree/bindings/media/ti-cal.txt | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/media/ti-cal.txt +3 -1
index 7e960cf26e23..cb2dc50a24fb 100644
@@ -7,7 +7,9 @@ processing capability to connect CSI2 image-sensor modules to the
 DRA72x device.
 
 Required properties:
-- compatible: must be "ti,dra72-cal"
+- compatible:
+ Should be "ti,dra72-cal", for DRA72 controllers
+ Should be "ti,dra72-pre-es2-cal", for DRA72 controllers pre ES2.0
 - reg:	CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX
 	control address space
 - reg-names: cal_top, cal_rx_core0, cal_rx_core1 and camerrx_control
Signature · 1 line
2.17.1
#7 lore raw

PATCH v2 7/20 media: ti-vpe: cal: add CSI2 PHY LDO errata support

In reply to Benoit Parrot

Apply Errata i913 every time the functional clock is enabled. This should take care of suspend/resume case as well.

---
 drivers/media/platform/ti-vpe/cal.c      | 58 +++++++++++++++++++++++-
 drivers/media/platform/ti-vpe/cal_regs.h | 27 +++++++++++
 2 files changed, 83 insertions(+), 2 deletions(-)
drivers/media/platform/ti-vpe/cal.c +56 -2
index 04e84c4dc92a..75d114e675cf 100644
@@ -284,6 +284,13 @@ static struct cal_data dra72x_cal_data = {
 	.flags = 0,
 };
 
+static struct cal_data dra72x_es1_cal_data = {
+	.csi2_phy_core = dra72x_cal_csi_phy,
+	.num_csi2_phy = ARRAY_SIZE(dra72x_cal_csi_phy),
+
+	.flags = DRA72_CAL_PRE_ES2_LDO_DISABLE,
+};
+
 /*
  * there is one cal_dev structure in the driver, it is shared by
  * all instances.
@@ -569,9 +576,52 @@ static void cal_get_hwinfo(struct cal_dev *dev)
 		hwinfo);
 }
 
-static inline int cal_runtime_get(struct cal_dev *dev)
+/*
+ *   Errata i913: CSI2 LDO Needs to be disabled when module is powered on
+ *
+ *   Enabling CSI2 LDO shorts it to core supply. It is crucial the 2 CSI2
+ *   LDOs on the device are disabled if CSI-2 module is powered on
+ *   (0x4845 B304 | 0x4845 B384 [28:27] = 0x1) or in ULPS (0x4845 B304
+ *   | 0x4845 B384 [28:27] = 0x2) mode. Common concerns include: high
+ *   current draw on the module supply in active mode.
+ *
+ *   Errata does not apply when CSI-2 module is powered off
+ *   (0x4845 B304 | 0x4845 B384 [28:27] = 0x0).
+ *
+ * SW Workaround:
+ *	Set the following register bits to disable the LDO,
+ *	which is essentially CSI2 REG10 bit 6:
+ *
+ *		Core 0:  0x4845 B828 = 0x0000 0040
+ *		Core 1:  0x4845 B928 = 0x0000 0040
+ */
+static void i913_errata(struct cal_dev *dev, unsigned int port)
+{
+	u32 reg10 = reg_read(dev->cc[port], CAL_CSI2_PHY_REG10);
+
+	set_field(&reg10, CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_DISABLE,
+		  CAL_CSI2_PHY_REG10_I933_LDO_DISABLE_MASK);
+
+	cal_dbg(1, dev, "CSI2_%d_REG10 = 0x%08x\n", port, reg10);
+	reg_write(dev->cc[port], CAL_CSI2_PHY_REG10, reg10);
+}
+
+static int cal_runtime_get(struct cal_dev *dev)
 {
-	return pm_runtime_get_sync(&dev->pdev->dev);
+	int r;
+
+	r = pm_runtime_get_sync(&dev->pdev->dev);
+
+	if (dev->flags & DRA72_CAL_PRE_ES2_LDO_DISABLE) {
+		/*
+		 * Apply errata on both port eveytime we (re-)enable
+		 * the clock
+		 */
+		i913_errata(dev, 0);
+		i913_errata(dev, 1);
+	}
+
+	return r;
 }
 
 static inline void cal_runtime_put(struct cal_dev *dev)
@@ -2061,6 +2111,10 @@ static const struct of_device_id cal_of_match[] = {
 		.compatible = "ti,dra72-cal",
 		.data = (void *)&dra72x_cal_data,
 	},
+	{
+		.compatible = "ti,dra72-pre-es2-cal",
+		.data = (void *)&dra72x_es1_cal_data,
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(of, cal_of_match);
drivers/media/platform/ti-vpe/cal_regs.h +27 -0
index 68cfc922b422..78d6f015c9ea 100644
@@ -10,6 +10,30 @@
 #ifndef __TI_CAL_REGS_H
 #define __TI_CAL_REGS_H
 
+/*
+ * struct cal_dev.flags possibilities
+ *
+ * DRA72_CAL_PRE_ES2_LDO_DISABLE:
+ *   Errata i913: CSI2 LDO Needs to be disabled when module is powered on
+ *
+ *   Enabling CSI2 LDO shorts it to core supply. It is crucial the 2 CSI2
+ *   LDOs on the device are disabled if CSI-2 module is powered on
+ *   (0x4845 B304 | 0x4845 B384 [28:27] = 0x1) or in ULPS (0x4845 B304
+ *   | 0x4845 B384 [28:27] = 0x2) mode. Common concerns include: high
+ *   current draw on the module supply in active mode.
+ *
+ *   Errata does not apply when CSI-2 module is powered off
+ *   (0x4845 B304 | 0x4845 B384 [28:27] = 0x0).
+ *
+ * SW Workaround:
+ *	Set the following register bits to disable the LDO,
+ *	which is essentially CSI2 REG10 bit 6:
+ *
+ *		Core 0:  0x4845 B828 = 0x0000 0040
+ *		Core 1:  0x4845 B928 = 0x0000 0040
+ */
+#define DRA72_CAL_PRE_ES2_LDO_DISABLE BIT(0)
+
 #define CAL_NUM_CSI2_PORTS		2
 
 /* CAL register offsets */
@@ -71,6 +95,7 @@
 #define CAL_CSI2_PHY_REG0		0x000
 #define CAL_CSI2_PHY_REG1		0x004
 #define CAL_CSI2_PHY_REG2		0x008
+#define CAL_CSI2_PHY_REG10		0x028
 
 /* CAL Control Module Core Camerrx Control register offsets */
 #define CM_CTRL_CORE_CAMERRX_CONTROL	0x000
@@ -458,6 +483,8 @@
 #define CAL_CSI2_PHY_REG1_CLOCK_MISS_DETECTOR_STATUS_SUCCESS		0
 #define CAL_CSI2_PHY_REG1_RESET_DONE_STATUS_MASK		GENMASK(29, 28)
 
+#define CAL_CSI2_PHY_REG10_I933_LDO_DISABLE_MASK		BIT_MASK(6)
+
 #define CAL_CSI2_PHY_REG2_CCP2_SYNC_PATTERN_MASK		GENMASK(23, 0)
 #define CAL_CSI2_PHY_REG2_TRIGGER_CMD_RXTRIGESC3_MASK		GENMASK(25, 24)
 #define CAL_CSI2_PHY_REG2_TRIGGER_CMD_RXTRIGESC2_MASK		GENMASK(27, 26)
Signature · 1 line
2.17.1
#8 lore raw

Re: [Patch v2 07/20] media: ti-vpe: cal: add CSI2 PHY LDO errata support

Hi Benoit,

On Mon, Nov 04, 2019 at 01:31:27PM -0600, Benoit Parrot wrote:

...

drivers/media/platform/ti-vpe/cal_regs.h line 486

Quoted 5 lines
drivers/media/platform/ti-vpe/cal_regs.h +1 -0
@@ -458,6 +483,8 @@
 #define CAL_CSI2_PHY_REG1_CLOCK_MISS_DETECTOR_STATUS_SUCCESS		0
 #define CAL_CSI2_PHY_REG1_RESET_DONE_STATUS_MASK		GENMASK(29, 28)
 
+#define CAL_CSI2_PHY_REG10_I933_LDO_DISABLE_MASK		BIT_MASK(6)

BIT(6) ?

BIT_MASK() is intended for a different purpose.

Signature · 3 lines
Regards,

Sakari Ailus
#9 lore raw

Re: [Patch v2 07/20] media: ti-vpe: cal: add CSI2 PHY LDO errata support

Sakari Ailus <[email protected]> wrote on Wed [2019-Nov-06 10:55:02 +0200]:

Quoted 10 lines

Hi Benoit,

On Mon, Nov 04, 2019 at 01:31:27PM -0600, Benoit Parrot wrote:

...

Quoted 4 lines
drivers/media/platform/ti-vpe/cal_regs.h +0 -0
@@ -458,6 +483,8 @@
 #define CAL_CSI2_PHY_REG1_CLOCK_MISS_DETECTOR_STATUS_SUCCESS		0
 #define CAL_CSI2_PHY_REG1_RESET_DONE_STATUS_MASK		GENMASK(29, 28)
 
Quoted 5 lines

drivers/media/platform/ti-vpe/cal_regs.h line 486

Quoted 1 line
drivers/media/platform/ti-vpe/cal_regs.h +1 -0
+#define CAL_CSI2_PHY_REG10_I933_LDO_DISABLE_MASK		BIT_MASK(6)

BIT(6) ?

BIT_MASK() is intended for a different purpose.

Wow, good catch, I have never realized that.

Benoit

Quoted 5 lines
Signature · 4 lines
-- 
Regards,

Sakari Ailus
#10 lore raw

Re: [Patch v2 07/20] media: ti-vpe: cal: add CSI2 PHY LDO errata support

In reply to Sakari Ailus

Sakari Ailus <[email protected]> wrote on Wed [2019-Nov-06 10:55:02 +0200]:

Quoted 10 lines

Hi Benoit,

On Mon, Nov 04, 2019 at 01:31:27PM -0600, Benoit Parrot wrote:

...

Quoted 4 lines
drivers/media/platform/ti-vpe/cal_regs.h +0 -0
@@ -458,6 +483,8 @@
 #define CAL_CSI2_PHY_REG1_CLOCK_MISS_DETECTOR_STATUS_SUCCESS		0
 #define CAL_CSI2_PHY_REG1_RESET_DONE_STATUS_MASK		GENMASK(29, 28)
 
Quoted 5 lines

drivers/media/platform/ti-vpe/cal_regs.h line 486

Quoted 1 line
drivers/media/platform/ti-vpe/cal_regs.h +1 -0
+#define CAL_CSI2_PHY_REG10_I933_LDO_DISABLE_MASK		BIT_MASK(6)

BIT(6) ?

BIT_MASK() is intended for a different purpose.

Well actually here I don't see the differences?

Quoted 5 lines
Signature · 4 lines
-- 
Regards,

Sakari Ailus
#11 lore raw

PATCH v2 8/20 media: ti-vpe: cal: Fix ths_term/ths_settle parameters

In reply to Benoit Parrot

The current method to calculate the ddr clk period is wrong. Therefore the ths_term calculation is incorrect. Also it was wrongly assumed that the ths_settle parameter was based on the control clock instead of the pixel clock.

Since the DPHY can tolerate quite a bit a of variation, capture was still mostly working with the 2 tested modes when the pixel clock was close to the control clock (i.e. 96 Mhz). But it would quickly stops working when using different modes or when customers used different sensors altogether.

Calculating the DDRClk period needs to take into account the pixel bit width and the number of active data lanes.

Based on the latest technical reference manual these parameters should now be calculated as follows:

THS_TERM: Programmed value = floor(20 ns/DDRClk period)
THS_SETTLE: Programmed value = floor(105 ns/DDRClk period) + 4

Also originally 'depth' was used to represent the number of bits a pixel would use once stored in memory (i.e. the container size). To accurately calculate the THS_* parameters we need to use the actual number of bits per pixels coming in from the sensor. So we are renaming 'depth' to 'bpp' (bits per pixels) and update the format table to show the actual number of bits per pixel being received.

The "container" size will be derived from the "bpp" value.

---
 drivers/media/platform/ti-vpe/cal.c | 98 +++++++++++++----------------
 1 file changed, 44 insertions(+), 54 deletions(-)
drivers/media/platform/ti-vpe/cal.c +44 -54
index 75d114e675cf..1abcdd98c33f 100644
@@ -73,8 +73,6 @@ static const struct v4l2_fract
 #define CAL_NUM_INPUT 1
 #define CAL_NUM_CONTEXT 2
 
-#define bytes_per_line(pixel, bpp) (ALIGN(pixel * bpp, 16))
-
 #define reg_read(dev, offset) ioread32(dev->base + offset)
 #define reg_write(dev, offset, val) iowrite32(val, dev->base + offset)
 
@@ -93,102 +91,103 @@ static const struct v4l2_fract
 struct cal_fmt {
 	u32	fourcc;
 	u32	code;
-	u8	depth;
+	/* Bits per pixel */
+	u8	bpp;
 };
 
 static struct cal_fmt cal_formats[] = {
 	{
 		.fourcc		= V4L2_PIX_FMT_YUYV,
 		.code		= MEDIA_BUS_FMT_YUYV8_2X8,
-		.depth		= 16,
+		.bpp		= 16,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_UYVY,
 		.code		= MEDIA_BUS_FMT_UYVY8_2X8,
-		.depth		= 16,
+		.bpp		= 16,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_YVYU,
 		.code		= MEDIA_BUS_FMT_YVYU8_2X8,
-		.depth		= 16,
+		.bpp		= 16,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_VYUY,
 		.code		= MEDIA_BUS_FMT_VYUY8_2X8,
-		.depth		= 16,
+		.bpp		= 16,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_RGB565, /* gggbbbbb rrrrrggg */
 		.code		= MEDIA_BUS_FMT_RGB565_2X8_LE,
-		.depth		= 16,
+		.bpp		= 16,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_RGB565X, /* rrrrrggg gggbbbbb */
 		.code		= MEDIA_BUS_FMT_RGB565_2X8_BE,
-		.depth		= 16,
+		.bpp		= 16,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_RGB555, /* gggbbbbb arrrrrgg */
 		.code		= MEDIA_BUS_FMT_RGB555_2X8_PADHI_LE,
-		.depth		= 16,
+		.bpp		= 16,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_RGB555X, /* arrrrrgg gggbbbbb */
 		.code		= MEDIA_BUS_FMT_RGB555_2X8_PADHI_BE,
-		.depth		= 16,
+		.bpp		= 16,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_RGB24, /* rgb */
 		.code		= MEDIA_BUS_FMT_RGB888_2X12_LE,
-		.depth		= 24,
+		.bpp		= 24,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_BGR24, /* bgr */
 		.code		= MEDIA_BUS_FMT_RGB888_2X12_BE,
-		.depth		= 24,
+		.bpp		= 24,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_RGB32, /* argb */
 		.code		= MEDIA_BUS_FMT_ARGB8888_1X32,
-		.depth		= 32,
+		.bpp		= 32,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SBGGR8,
 		.code		= MEDIA_BUS_FMT_SBGGR8_1X8,
-		.depth		= 8,
+		.bpp		= 8,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SGBRG8,
 		.code		= MEDIA_BUS_FMT_SGBRG8_1X8,
-		.depth		= 8,
+		.bpp		= 8,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SGRBG8,
 		.code		= MEDIA_BUS_FMT_SGRBG8_1X8,
-		.depth		= 8,
+		.bpp		= 8,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SRGGB8,
 		.code		= MEDIA_BUS_FMT_SRGGB8_1X8,
-		.depth		= 8,
+		.bpp		= 8,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SBGGR10,
 		.code		= MEDIA_BUS_FMT_SBGGR10_1X10,
-		.depth		= 16,
+		.bpp		= 10,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SGBRG10,
 		.code		= MEDIA_BUS_FMT_SGBRG10_1X10,
-		.depth		= 16,
+		.bpp		= 10,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SGRBG10,
 		.code		= MEDIA_BUS_FMT_SGRBG10_1X10,
-		.depth		= 16,
+		.bpp		= 10,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SRGGB10,
 		.code		= MEDIA_BUS_FMT_SRGGB10_1X10,
-		.depth		= 16,
+		.bpp		= 10,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SBGGR12,
 		.code		= MEDIA_BUS_FMT_SBGGR12_1X12,
-		.depth		= 16,
+		.bpp		= 12,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SGBRG12,
 		.code		= MEDIA_BUS_FMT_SGBRG12_1X12,
-		.depth		= 16,
+		.bpp		= 12,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SGRBG12,
 		.code		= MEDIA_BUS_FMT_SGRBG12_1X12,
-		.depth		= 16,
+		.bpp		= 12,
 	}, {
 		.fourcc		= V4L2_PIX_FMT_SRGGB12,
 		.code		= MEDIA_BUS_FMT_SRGGB12_1X12,
-		.depth		= 16,
+		.bpp		= 12,
 	},
 };
 
@@ -873,41 +872,28 @@ static void cal_wr_dma_addr(struct cal_ctx *ctx, unsigned int dmaaddr)
 #define TCLK_TERM	0
 #define TCLK_MISS	1
 #define TCLK_SETTLE	14
-#define THS_SETTLE	15
 
 static void csi2_phy_config(struct cal_ctx *ctx)
 {
 	unsigned int reg0, reg1;
 	unsigned int ths_term, ths_settle;
-	unsigned int ddrclkperiod_us;
+	unsigned int csi2_ddrclk_khz;
+	struct v4l2_fwnode_bus_mipi_csi2 *mipi_csi2 =
+			&ctx->endpoint.bus.mipi_csi2;
+	u32 num_lanes = mipi_csi2->num_data_lanes;
 
-	/*
-	 * THS_TERM: Programmed value = floor(20 ns/DDRClk period) - 2.
-	 */
-	ddrclkperiod_us = ctx->external_rate / 2000000;
-	ddrclkperiod_us = 1000000 / ddrclkperiod_us;
-	ctx_dbg(1, ctx, "ddrclkperiod_us: %d\n", ddrclkperiod_us);
+	/* DPHY timing configuration */
+	/* CSI-2 is DDR and we only count used lanes. */
+	csi2_ddrclk_khz = ctx->external_rate / 1000
+		/ (2 * num_lanes) * ctx->fmt->bpp;
+	ctx_dbg(1, ctx, "csi2_ddrclk_khz: %d\n", csi2_ddrclk_khz);
 
-	ths_term = 20000 / ddrclkperiod_us;
-	ths_term = (ths_term >= 2) ? ths_term - 2 : ths_term;
+	/* THS_TERM: Programmed value = floor(20 ns/DDRClk period) */
+	ths_term = 20 * csi2_ddrclk_khz / 1000000;
 	ctx_dbg(1, ctx, "ths_term: %d (0x%02x)\n", ths_term, ths_term);
 
-	/*
-	 * THS_SETTLE: Programmed value = floor(176.3 ns/CtrlClk period) - 1.
-	 *	Since CtrlClk is fixed at 96Mhz then we get
-	 *	ths_settle = floor(176.3 / 10.416) - 1 = 15
-	 * If we ever switch to a dynamic clock then this code might be useful
-	 *
-	 * unsigned int ctrlclkperiod_us;
-	 * ctrlclkperiod_us = 96000000 / 1000000;
-	 * ctrlclkperiod_us = 1000000 / ctrlclkperiod_us;
-	 * ctx_dbg(1, ctx, "ctrlclkperiod_us: %d\n", ctrlclkperiod_us);
-
-	 * ths_settle = 176300  / ctrlclkperiod_us;
-	 * ths_settle = (ths_settle > 1) ? ths_settle - 1 : ths_settle;
-	 */
-
-	ths_settle = THS_SETTLE;
+	/* THS_SETTLE: Programmed value = floor(105 ns/DDRClk period) + 4 */
+	ths_settle = (105 * csi2_ddrclk_khz / 1000000) + 4;
 	ctx_dbg(1, ctx, "ths_settle: %d (0x%02x)\n", ths_settle, ths_settle);
 
 	reg0 = reg_read(ctx->cc, CAL_CSI2_PHY_REG0);
@@ -1119,6 +1105,8 @@ static int cal_calc_format_size(struct cal_ctx *ctx,
 				const struct cal_fmt *fmt,
 				struct v4l2_format *f)
 {
+	u32 bpl;
+
 	if (!fmt) {
 		ctx_dbg(3, ctx, "No cal_fmt provided!\n");
 		return -EINVAL;
@@ -1126,8 +1114,10 @@ static int cal_calc_format_size(struct cal_ctx *ctx,
 
 	v4l_bound_align_image(&f->fmt.pix.width, 48, MAX_WIDTH, 2,
 			      &f->fmt.pix.height, 32, MAX_HEIGHT, 0, 0);
-	f->fmt.pix.bytesperline = bytes_per_line(f->fmt.pix.width,
-						 fmt->depth >> 3);
+
+	bpl = (f->fmt.pix.width * ALIGN(fmt->bpp, 8)) >> 3;
+	f->fmt.pix.bytesperline = ALIGN(bpl, 16);
+
 	f->fmt.pix.sizeimage = f->fmt.pix.height *
 			       f->fmt.pix.bytesperline;
 
Signature · 1 line
2.17.1
#12 lore raw

PATCH v2 9/20 media: ti-vpe: cal: Fix pixel processing parameters

In reply to Benoit Parrot

The pixel processing unit was hard coded to only handle 8 bits per pixel from input to output.

We now add handling for 10, 12 and 16 bits per pixel at the source and setting the in-memory size (i.e. container size) to 16 bits for these 3 cases.

---
 drivers/media/platform/ti-vpe/cal.c | 41 ++++++++++++++++++++++++++---
 1 file changed, 38 insertions(+), 3 deletions(-)
drivers/media/platform/ti-vpe/cal.c +38 -3
index 1abcdd98c33f..1b7dcf9ba9e2 100644
@@ -803,13 +803,48 @@ static void csi2_ctx_config(struct cal_ctx *ctx)
 
 static void pix_proc_config(struct cal_ctx *ctx)
 {
-	u32 val;
+	u32 val, extract, pack;
+
+	switch (ctx->fmt->bpp) {
+	case 8:
+		extract = CAL_PIX_PROC_EXTRACT_B8;
+		pack = CAL_PIX_PROC_PACK_B8;
+		break;
+	case 10:
+		extract = CAL_PIX_PROC_EXTRACT_B10_MIPI;
+		pack = CAL_PIX_PROC_PACK_B16;
+		break;
+	case 12:
+		extract = CAL_PIX_PROC_EXTRACT_B12_MIPI;
+		pack = CAL_PIX_PROC_PACK_B16;
+		break;
+	case 16:
+		extract = CAL_PIX_PROC_EXTRACT_B16_LE;
+		pack = CAL_PIX_PROC_PACK_B16;
+		break;
+	default:
+		/*
+		 * If you see this warning then it means that you added
+		 * some new entry in the cal_formats[] array with a different
+		 * bit per pixel values then the one supported below.
+		 * Either add support for the new bpp value below or adjust
+		 * the new entry to use one of the value below.
+		 *
+		 * Instead of failing here just use 8 bpp as a default.
+		 */
+		dev_warn_once(&ctx->dev->pdev->dev,
+			      "%s:%d:%s: bpp:%d unsupported! Overwritten with 8.\n",
+			      __FILE__, __LINE__, __func__, ctx->fmt->bpp);
+		extract = CAL_PIX_PROC_EXTRACT_B8;
+		pack = CAL_PIX_PROC_PACK_B8;
+		break;
+	}
 
 	val = reg_read(ctx->dev, CAL_PIX_PROC(ctx->csi2_port));
-	set_field(&val, CAL_PIX_PROC_EXTRACT_B8, CAL_PIX_PROC_EXTRACT_MASK);
+	set_field(&val, extract, CAL_PIX_PROC_EXTRACT_MASK);
 	set_field(&val, CAL_PIX_PROC_DPCMD_BYPASS, CAL_PIX_PROC_DPCMD_MASK);
 	set_field(&val, CAL_PIX_PROC_DPCME_BYPASS, CAL_PIX_PROC_DPCME_MASK);
-	set_field(&val, CAL_PIX_PROC_PACK_B8, CAL_PIX_PROC_PACK_MASK);
+	set_field(&val, pack, CAL_PIX_PROC_PACK_MASK);
 	set_field(&val, ctx->csi2_port, CAL_PIX_PROC_CPORT_MASK);
 	set_field(&val, CAL_GEN_ENABLE, CAL_PIX_PROC_EN_MASK);
 	reg_write(ctx->dev, CAL_PIX_PROC(ctx->csi2_port), val);
Signature · 1 line
2.17.1
#13 lore raw

PATCH v2 10/20 media: ti-vpe: cal: Align DPHY init sequence with docs

In reply to Benoit Parrot

The current CSI2 DPHY initialization sequence although functional does not match with the documented sequence in the Technical Reference Manual.

This may affect capture re-startability in stop/start situations.

---
 drivers/media/platform/ti-vpe/cal.c | 199 ++++++++++++++++++++++++----
 1 file changed, 172 insertions(+), 27 deletions(-)
drivers/media/platform/ti-vpe/cal.c +172 -27
index 1b7dcf9ba9e2..b348d99d6166 100644
@@ -689,29 +689,76 @@ static void disable_irqs(struct cal_ctx *ctx)
 	reg_write(ctx->dev, CAL_CSI2_VC_IRQENABLE(1), 0);
 }
 
-static void csi2_init(struct cal_ctx *ctx)
+static void csi2_phy_config(struct cal_ctx *ctx);
+
+static void csi2_phy_init(struct cal_ctx *ctx)
 {
 	int i;
 	u32 val;
 
+	/* Steps
+	 *  1. Configure D-PHY mode and enable required lanes
+	 *  2. Reset complex IO - Wait for completion of reset
+	 *          Note if the external sensor is not sending byte clock,
+	 *          the reset will timeout
+	 *  3 Program Stop States
+	 *      A. Program THS_TERM, THS_SETTLE, etc... Timings parameters
+	 *              in terms of DDR clock periods
+	 *      B. Enable stop state transition timeouts
+	 *  4.Force FORCERXMODE
+	 *      D. Enable pull down using pad control
+	 *      E. Power up PHY
+	 *      F. Wait for power up completion
+	 *      G. Wait for all enabled lane to reach stop state
+	 *      H. Disable pull down using pad control
+	 */
+
+	/* 1. Configure D-PHY mode and enable required lanes */
+	camerarx_phy_enable(ctx);
+
+	/* 2. Reset complex IO - Do not wait for reset completion */
+	val = reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port));
+	set_field(&val, CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL_OPERATIONAL,
+		  CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL_MASK);
+	reg_write(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port), val);
+	ctx_dbg(3, ctx, "CAL_CSI2_COMPLEXIO_CFG(%d) = 0x%08x De-assert Complex IO Reset\n",
+		ctx->csi2_port,
+		reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port)));
+
+	/* Dummy read to allow SCP to complete */
+	val = reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port));
+
+	/* 3.A. Program Phy Timing Parameters */
+	csi2_phy_config(ctx);
+
+	/* 3.B. Program Stop States */
 	val = reg_read(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port));
-	set_field(&val, CAL_GEN_ENABLE,
-		  CAL_CSI2_TIMING_FORCE_RX_MODE_IO1_MASK);
 	set_field(&val, CAL_GEN_ENABLE,
 		  CAL_CSI2_TIMING_STOP_STATE_X16_IO1_MASK);
 	set_field(&val, CAL_GEN_DISABLE,
 		  CAL_CSI2_TIMING_STOP_STATE_X4_IO1_MASK);
 	set_field(&val, 407, CAL_CSI2_TIMING_STOP_STATE_COUNTER_IO1_MASK);
 	reg_write(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port), val);
-	ctx_dbg(3, ctx, "CAL_CSI2_TIMING(%d) = 0x%08x\n", ctx->csi2_port,
+	ctx_dbg(3, ctx, "CAL_CSI2_TIMING(%d) = 0x%08x Stop States\n",
+		ctx->csi2_port,
+		reg_read(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port)));
+
+	/* 4. Force FORCERXMODE */
+	val = reg_read(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port));
+	set_field(&val, CAL_GEN_ENABLE,
+		  CAL_CSI2_TIMING_FORCE_RX_MODE_IO1_MASK);
+	reg_write(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port), val);
+	ctx_dbg(3, ctx, "CAL_CSI2_TIMING(%d) = 0x%08x Force RXMODE\n",
+		ctx->csi2_port,
 		reg_read(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port)));
 
+	/* E. Power up the PHY using the complex IO */
 	val = reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port));
-	set_field(&val, CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL_OPERATIONAL,
-		  CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL_MASK);
 	set_field(&val, CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_STATE_ON,
 		  CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_MASK);
 	reg_write(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port), val);
+
+	/* F. Wait for power up completion */
 	for (i = 0; i < 10; i++) {
 		if (reg_read_field(ctx->dev,
 				   CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port),
@@ -720,18 +767,104 @@ static void csi2_init(struct cal_ctx *ctx)
 			break;
 		usleep_range(1000, 1100);
 	}
-	ctx_dbg(3, ctx, "CAL_CSI2_COMPLEXIO_CFG(%d) = 0x%08x\n", ctx->csi2_port,
-		reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port)));
+	ctx_dbg(3, ctx, "CAL_CSI2_COMPLEXIO_CFG(%d) = 0x%08x Powered UP %s\n",
+		ctx->csi2_port,
+		reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port)),
+		(i >= 10) ? "(timeout)" : "");
+}
 
-	val = reg_read(ctx->dev, CAL_CTRL);
-	set_field(&val, CAL_CTRL_BURSTSIZE_BURST128, CAL_CTRL_BURSTSIZE_MASK);
-	set_field(&val, 0xF, CAL_CTRL_TAGCNT_MASK);
-	set_field(&val, CAL_CTRL_POSTED_WRITES_NONPOSTED,
-		  CAL_CTRL_POSTED_WRITES_MASK);
-	set_field(&val, 0xFF, CAL_CTRL_MFLAGL_MASK);
-	set_field(&val, 0xFF, CAL_CTRL_MFLAGH_MASK);
-	reg_write(ctx->dev, CAL_CTRL, val);
-	ctx_dbg(3, ctx, "CAL_CTRL = 0x%08x\n", reg_read(ctx->dev, CAL_CTRL));
+static void csi2_wait_for_phy(struct cal_ctx *ctx)
+{
+	int i;
+
+	/* Steps
+	 *  2. Wait for completion of reset
+	 *          Note if the external sensor is not sending byte clock,
+	 *          the reset will timeout
+	 *  4.Force FORCERXMODE
+	 *      G. Wait for all enabled lane to reach stop state
+	 *      H. Disable pull down using pad control
+	 */
+
+	/* 2. Wait for reset completion */
+	for (i = 0; i < 250; i++) {
+		if (reg_read_field(ctx->dev,
+				   CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port),
+				   CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_MASK) ==
+		    CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_RESETCOMPLETED)
+			break;
+		usleep_range(1000, 1100);
+	}
+	ctx_dbg(3, ctx, "CAL_CSI2_COMPLEXIO_CFG(%d) = 0x%08x Complex IO Reset Done (%d) %s\n",
+		ctx->csi2_port,
+		reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port)), i,
+		(i >= 250) ? "(timeout)" : "");
+
+	/* 4. G. Wait for all enabled lane to reach stop state */
+	for (i = 0; i < 10; i++) {
+		if (reg_read_field(ctx->dev,
+				   CAL_CSI2_TIMING(ctx->csi2_port),
+				   CAL_CSI2_TIMING_FORCE_RX_MODE_IO1_MASK) ==
+		    CAL_GEN_DISABLE)
+			break;
+		usleep_range(1000, 1100);
+	}
+	ctx_dbg(3, ctx, "CAL_CSI2_TIMING(%d) = 0x%08x Stop State Reached %s\n",
+		ctx->csi2_port,
+		reg_read(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port)),
+		(i >= 10) ? "(timeout)" : "");
+
+	ctx_dbg(1, ctx, "CSI2_%d_REG1 = 0x%08x (Bit(31,28) should be set!)\n",
+		(ctx->csi2_port - 1), reg_read(ctx->cc, CAL_CSI2_PHY_REG1));
+}
+
+static void csi2_phy_deinit(struct cal_ctx *ctx)
+{
+	int i;
+	u32 val;
+
+	/* Power down the PHY using the complex IO */
+	val = reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port));
+	set_field(&val, CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_STATE_OFF,
+		  CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_MASK);
+	reg_write(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port), val);
+
+	/* Wait for power down completion */
+	for (i = 0; i < 10; i++) {
+		if (reg_read_field(ctx->dev,
+				   CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port),
+				   CAL_CSI2_COMPLEXIO_CFG_PWR_STATUS_MASK) ==
+		    CAL_CSI2_COMPLEXIO_CFG_PWR_STATUS_STATE_OFF)
+			break;
+		usleep_range(1000, 1100);
+	}
+	ctx_dbg(3, ctx, "CAL_CSI2_COMPLEXIO_CFG(%d) = 0x%08x Powered Down %s\n",
+		ctx->csi2_port,
+		reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port)),
+		(i >= 10) ? "(timeout)" : "");
+
+	/* Assert Comple IO Reset */
+	val = reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port));
+	set_field(&val, CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL,
+		  CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL_MASK);
+	reg_write(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port), val);
+
+	/* Wait for power down completion */
+	for (i = 0; i < 10; i++) {
+		if (reg_read_field(ctx->dev,
+				   CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port),
+				   CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_MASK) ==
+		    CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_RESETONGOING)
+			break;
+		usleep_range(1000, 1100);
+	}
+	ctx_dbg(3, ctx, "CAL_CSI2_COMPLEXIO_CFG(%d) = 0x%08x Complex IO in Reset (%d) %s\n",
+		ctx->csi2_port,
+		reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port)), i,
+		(i >= 10) ? "(timeout)" : "");
+
+	/* Disable the phy */
+	camerarx_phy_disable(ctx);
 }
 
 static void csi2_lane_config(struct cal_ctx *ctx)
@@ -894,6 +1027,16 @@ static void cal_wr_dma_config(struct cal_ctx *ctx,
 	reg_write(ctx->dev, CAL_WR_DMA_XSIZE(ctx->csi2_port), val);
 	ctx_dbg(3, ctx, "CAL_WR_DMA_XSIZE(%d) = 0x%08x\n", ctx->csi2_port,
 		reg_read(ctx->dev, CAL_WR_DMA_XSIZE(ctx->csi2_port)));
+
+	val = reg_read(ctx->dev, CAL_CTRL);
+	set_field(&val, CAL_CTRL_BURSTSIZE_BURST128, CAL_CTRL_BURSTSIZE_MASK);
+	set_field(&val, 0xF, CAL_CTRL_TAGCNT_MASK);
+	set_field(&val, CAL_CTRL_POSTED_WRITES_NONPOSTED,
+		  CAL_CTRL_POSTED_WRITES_MASK);
+	set_field(&val, 0xFF, CAL_CTRL_MFLAGL_MASK);
+	set_field(&val, 0xFF, CAL_CTRL_MFLAGH_MASK);
+	reg_write(ctx->dev, CAL_CTRL, val);
+	ctx_dbg(3, ctx, "CAL_CTRL = 0x%08x\n", reg_read(ctx->dev, CAL_CTRL));
 }
 
 static void cal_wr_dma_addr(struct cal_ctx *ctx, unsigned int dmaaddr)
@@ -1466,17 +1609,14 @@ static int cal_start_streaming(struct vb2_queue *vq, unsigned int count)
 
 	cal_runtime_get(ctx->dev);
 
-	enable_irqs(ctx);
-	camerarx_phy_enable(ctx);
-	csi2_init(ctx);
-	csi2_phy_config(ctx);
-	csi2_lane_config(ctx);
 	csi2_ctx_config(ctx);
 	pix_proc_config(ctx);
 	cal_wr_dma_config(ctx, ctx->v_fmt.fmt.pix.bytesperline,
 			  ctx->v_fmt.fmt.pix.height);
-	cal_wr_dma_addr(ctx, addr);
-	csi2_ppi_enable(ctx);
+	csi2_lane_config(ctx);
+
+	enable_irqs(ctx);
+	csi2_phy_init(ctx);
 
 	ret = v4l2_subdev_call(ctx->sensor, video, s_stream, 1);
 	if (ret) {
@@ -1485,6 +1625,10 @@ static int cal_start_streaming(struct vb2_queue *vq, unsigned int count)
 		goto err;
 	}
 
+	csi2_wait_for_phy(ctx);
+	cal_wr_dma_addr(ctx, addr);
+	csi2_ppi_enable(ctx);
+
 	if (debug >= 4)
 		cal_quickdump_regs(ctx->dev);
 
@@ -1505,11 +1649,12 @@ static void cal_stop_streaming(struct vb2_queue *vq)
 	struct cal_buffer *buf, *tmp;
 	unsigned long flags;
 
-	if (v4l2_subdev_call(ctx->sensor, video, s_stream, 0))
-		ctx_err(ctx, "stream off failed in subdev\n");
-
 	csi2_ppi_disable(ctx);
 	disable_irqs(ctx);
+	csi2_phy_deinit(ctx);
+
+	if (v4l2_subdev_call(ctx->sensor, video, s_stream, 0))
+		ctx_err(ctx, "stream off failed in subdev\n");
 
 	/* Release all active buffers */
 	spin_lock_irqsave(&ctx->slock, flags);
Signature · 1 line
2.17.1
#14 lore raw

PATCH v2 11/20 dt-bindings: media: cal: update binding to add DRA76x support

In reply to Benoit Parrot

Update Device Tree bindings for the CAL driver to add DRA76x support.

---
 Documentation/devicetree/bindings/media/ti-cal.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/media/ti-cal.txt +1 -0
index cb2dc50a24fb..eca28a779370 100644
@@ -10,6 +10,7 @@ Required properties:
 - compatible:
  Should be "ti,dra72-cal", for DRA72 controllers
  Should be "ti,dra72-pre-es2-cal", for DRA72 controllers pre ES2.0
+ Should be "ti,dra76-cal", for DRA76 controllers
 - reg:	CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX
 	control address space
 - reg-names: cal_top, cal_rx_core0, cal_rx_core1 and camerrx_control
Signature · 1 line
2.17.1
#15 lore raw

PATCH v2 12/20 media: ti-vpe: cal: Add DRA76x support

In reply to Benoit Parrot

Add the needed control module register bit layout to support the DRA76x family of devices.

---
 drivers/media/platform/ti-vpe/cal.c | 36 +++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)
drivers/media/platform/ti-vpe/cal.c +36 -0
index b348d99d6166..72ed2348389d 100644
@@ -290,6 +290,38 @@ static struct cal_data dra72x_es1_cal_data = {
 	.flags = DRA72_CAL_PRE_ES2_LDO_DISABLE,
 };
 
+static struct reg_field dra76x_ctrl_core_csi0_reg_fields[F_MAX_FIELDS] = {
+	[F_CTRLCLKEN] = REG_FIELD(0, 8, 8),
+	[F_CAMMODE] = REG_FIELD(0, 9, 10),
+	[F_CSI_MODE] = REG_FIELD(0, 11, 11),
+	[F_LANEENABLE] = REG_FIELD(0, 27, 31),
+};
+
+static struct reg_field dra76x_ctrl_core_csi1_reg_fields[F_MAX_FIELDS] = {
+	[F_CTRLCLKEN] = REG_FIELD(0, 0, 0),
+	[F_CAMMODE] = REG_FIELD(0, 1, 2),
+	[F_CSI_MODE] = REG_FIELD(0, 3, 3),
+	[F_LANEENABLE] = REG_FIELD(0, 24, 26),
+};
+
+static struct cal_csi2_phy dra76x_cal_csi_phy[] = {
+	{
+		.base_fields = dra76x_ctrl_core_csi0_reg_fields,
+		.num_lanes = 5,
+	},
+	{
+		.base_fields = dra76x_ctrl_core_csi1_reg_fields,
+		.num_lanes = 3,
+	},
+};
+
+static struct cal_data dra76x_cal_data = {
+	.csi2_phy_core = dra76x_cal_csi_phy,
+	.num_csi2_phy = ARRAY_SIZE(dra76x_cal_csi_phy),
+
+	.flags = 0,
+};
+
 /*
  * there is one cal_dev structure in the driver, it is shared by
  * all instances.
@@ -2285,6 +2317,10 @@ static const struct of_device_id cal_of_match[] = {
 		.compatible = "ti,dra72-pre-es2-cal",
 		.data = (void *)&dra72x_es1_cal_data,
 	},
+	{
+		.compatible = "ti,dra76-cal",
+		.data = (void *)&dra76x_cal_data,
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(of, cal_of_match);
Signature · 1 line
2.17.1
#16 lore raw

Re: [Patch v2 12/20] media: ti-vpe: cal: Add DRA76x support

Hi Benoit,

On Mon, Nov 04, 2019 at 01:31:32PM -0600, Benoit Parrot wrote:

...

Quoted 1 line

+static struct cal_data dra76x_cal_data = {

const?

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra72x_es1_cal_data = { · line 321

Quoted 3 lines
drivers/media/platform/ti-vpe/cal.c +3 -0
+	.csi2_phy_core = dra76x_cal_csi_phy,
+	.num_csi2_phy = ARRAY_SIZE(dra76x_cal_csi_phy),
+

This newline seems extra.

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra72x_es1_cal_data = { · line 322

Quoted 1 line
drivers/media/platform/ti-vpe/cal.c +1 -0
+	.flags = 0,

And flags will be zero in any case, as one more struct members are assigned to.

Quoted 1 line

+};

Signature · 3 lines
Regards,

Sakari Ailus
#17 lore raw

Re: [Patch v2 12/20] media: ti-vpe: cal: Add DRA76x support

Sakari Ailus <[email protected]> wrote on Wed [2019-Nov-06 10:57:09 +0200]:

Quoted 9 lines

Hi Benoit,

On Mon, Nov 04, 2019 at 01:31:32PM -0600, Benoit Parrot wrote:

...

Quoted 1 line

+static struct cal_data dra76x_cal_data = {

const?

Hmm, most likely.

Quoted 11 lines

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra72x_es1_cal_data = { · line 321

Quoted 4 lines
drivers/media/platform/ti-vpe/cal.c +3 -0
+	.csi2_phy_core = dra76x_cal_csi_phy,
+	.num_csi2_phy = ARRAY_SIZE(dra76x_cal_csi_phy),
+

This newline seems extra.

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra72x_es1_cal_data = { · line 322

Quoted 1 line
drivers/media/platform/ti-vpe/cal.c +1 -0
+	.flags = 0,

And flags will be zero in any case, as one more struct members are assigned to.

Is this guaranteed or compiler version dependent?

Quoted 7 lines
Quoted 2 lines

+};

Signature · 3 lines
Regards,

Sakari Ailus
#18 lore raw

Re: [Patch v2 12/20] media: ti-vpe: cal: Add DRA76x support

Quoted 20 lines · Benoit Parrot

Sakari Ailus <[email protected]> wrote on Wed [2019-Nov-06 10:57:09 +0200]:

Quoted 9 lines

Hi Benoit,

On Mon, Nov 04, 2019 at 01:31:32PM -0600, Benoit Parrot wrote:

...

Quoted 1 line

+static struct cal_data dra76x_cal_data = {

const?

Hmm, most likely.

Quoted 7 lines

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra72x_es1_cal_data = { · line 321

Quoted 4 lines
drivers/media/platform/ti-vpe/cal.c +3 -0
+	.csi2_phy_core = dra76x_cal_csi_phy,
+	.num_csi2_phy = ARRAY_SIZE(dra76x_cal_csi_phy),
+

This newline seems extra.

Quoted 6 lines
Quoted 4 lines

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra72x_es1_cal_data = { · line 322

Quoted 1 line
drivers/media/platform/ti-vpe/cal.c +1 -0
+	.flags = 0,

And flags will be zero in any case, as one more struct members are assigned to.

Is this guaranteed or compiler version dependent?

C standard.

Signature · 1 line
Sakari Ailus
#19 lore raw

Re: [Patch v2 12/20] media: ti-vpe: cal: Add DRA76x support

In reply to Benoit Parrot

Benoit Parrot <[email protected]> wrote on Wed [2019-Nov-06 14:58:39 -0600]:

Quoted 5 lines

Sakari Ailus <[email protected]> wrote on Wed [2019-Nov-06 10:57:09 +0200]:

Quoted 4 lines

Hi Benoit,

On Mon, Nov 04, 2019 at 01:31:32PM -0600, Benoit Parrot wrote:

Quoted 7 lines
Quoted 5 lines

...

Quoted 1 line

+static struct cal_data dra76x_cal_data = {

const?

Hmm, most likely.

Well, it turns out they cannot be constified because we need to be able to update the register offset fir the regmap used for the syscon object. So I'll leave them as is.

Benoit

Quoted 22 lines
Quoted 8 lines

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra72x_es1_cal_data = { · line 321

Quoted 5 lines
drivers/media/platform/ti-vpe/cal.c +3 -0
+	.csi2_phy_core = dra76x_cal_csi_phy,
+	.num_csi2_phy = ARRAY_SIZE(dra76x_cal_csi_phy),
+

This newline seems extra.

Quoted 4 lines

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra72x_es1_cal_data = { · line 322

Quoted 1 line
drivers/media/platform/ti-vpe/cal.c +1 -0
+	.flags = 0,

And flags will be zero in any case, as one more struct members are assigned to.

Is this guaranteed or compiler version dependent?

Quoted 7 lines
Quoted 2 lines

+};

Signature · 3 lines
Regards,

Sakari Ailus
#20 lore raw

Re: [Patch v2 12/20] media: ti-vpe: cal: Add DRA76x support

Benoit Parrot <[email protected]> wrote on Tue [2019-Nov-12 07:28:11 -0600]:

Quoted 10 lines

Benoit Parrot <[email protected]> wrote on Wed [2019-Nov-06 14:58:39 -0600]:

Quoted 9 lines

Sakari Ailus <[email protected]> wrote on Wed [2019-Nov-06 10:57:09 +0200]:

Quoted 8 lines

Hi Benoit,

On Mon, Nov 04, 2019 at 01:31:32PM -0600, Benoit Parrot wrote:

...

Quoted 1 line

+static struct cal_data dra76x_cal_data = {

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

const?

Hmm, most likely.

Well, it turns out they cannot be constified because we need to be able to update the register offset fir the regmap used for the syscon object. So I'll leave them as is.

Oh I guess you meant just the "static struct cal_data" ones? I tried making the other one into const but obviously that didn't work.

But just constifying "static struct cal_data" appears to compiled just fine.

Quoted 25 lines

Benoit

Quoted 22 lines
Quoted 8 lines

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra72x_es1_cal_data = { · line 321

Quoted 5 lines
drivers/media/platform/ti-vpe/cal.c +3 -0
+	.csi2_phy_core = dra76x_cal_csi_phy,
+	.num_csi2_phy = ARRAY_SIZE(dra76x_cal_csi_phy),
+

This newline seems extra.

Quoted 4 lines

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra72x_es1_cal_data = { · line 322

Quoted 1 line
drivers/media/platform/ti-vpe/cal.c +1 -0
+	.flags = 0,

And flags will be zero in any case, as one more struct members are assigned to.

Is this guaranteed or compiler version dependent?

Quoted 7 lines
Quoted 2 lines

+};

Signature · 3 lines
Regards,

Sakari Ailus
#21 lore raw

PATCH v2 13/20 dt-bindings: media: cal: update binding to add AM654 support

In reply to Benoit Parrot

Update Device Tree bindings for the CAL driver to add AM654 support.

---
 Documentation/devicetree/bindings/media/ti-cal.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/media/ti-cal.txt +1 -0
index eca28a779370..2deb256e7032 100644
@@ -11,6 +11,7 @@ Required properties:
  Should be "ti,dra72-cal", for DRA72 controllers
  Should be "ti,dra72-pre-es2-cal", for DRA72 controllers pre ES2.0
  Should be "ti,dra76-cal", for DRA76 controllers
+ Should be "ti,am654-cal", for AM654 controllers
 - reg:	CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX
 	control address space
 - reg-names: cal_top, cal_rx_core0, cal_rx_core1 and camerrx_control
Signature · 1 line
2.17.1
#22 lore raw

PATCH v2 14/20 media: ti-vpe: cal: Add AM654 support

In reply to Benoit Parrot

Add the needed control module register bit layout to support the AM654 family of devices.

---
 drivers/media/platform/Kconfig      |  2 +-
 drivers/media/platform/ti-vpe/cal.c | 28 +++++++++++++++++++++++++++-
 2 files changed, 28 insertions(+), 2 deletions(-)
drivers/media/platform/Kconfig +1 -1
index e84f35d3a68e..995f4c67f764 100644
@@ -151,7 +151,7 @@ source "drivers/media/platform/sunxi/Kconfig"
 config VIDEO_TI_CAL
 	tristate "TI CAL (Camera Adaptation Layer) driver"
 	depends on VIDEO_DEV && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
-	depends on SOC_DRA7XX || COMPILE_TEST
+	depends on SOC_DRA7XX || ARCH_K3 || COMPILE_TEST
 	select VIDEOBUF2_DMA_CONTIG
 	select V4L2_FWNODE
 	help
drivers/media/platform/ti-vpe/cal.c +27 -1
index 72ed2348389d..45653e9ed6cd 100644
@@ -322,6 +322,26 @@ static struct cal_data dra76x_cal_data = {
 	.flags = 0,
 };
 
+static struct reg_field am654_ctrl_core_csi0_reg_fields[F_MAX_FIELDS] = {
+	[F_CTRLCLKEN] = REG_FIELD(0, 15, 15),
+	[F_CAMMODE] = REG_FIELD(0, 24, 25),
+	[F_LANEENABLE] = REG_FIELD(0, 0, 4),
+};
+
+static struct cal_csi2_phy am654_cal_csi_phy[] = {
+	{
+		.base_fields = am654_ctrl_core_csi0_reg_fields,
+		.num_lanes = 5,
+	},
+};
+
+static struct cal_data am654_cal_data = {
+	.csi2_phy_core = am654_cal_csi_phy,
+	.num_csi2_phy = ARRAY_SIZE(am654_cal_csi_phy),
+
+	.flags = 0,
+};
+
 /*
  * there is one cal_dev structure in the driver, it is shared by
  * all instances.
@@ -548,7 +568,9 @@ static void camerarx_phy_enable(struct cal_ctx *ctx)
 	/* Always enable all lanes at the phy control level */
 	max_lanes = (1 << cal_data_get_phy_max_lanes(ctx)) - 1;
 	regmap_field_write(phy->fields[F_LANEENABLE], max_lanes);
-	regmap_field_write(phy->fields[F_CSI_MODE], 1);
+	/* F_CSI_MODE is not present on every architecture */
+	if (phy->fields[F_CSI_MODE])
+		regmap_field_write(phy->fields[F_CSI_MODE], 1);
 	regmap_field_write(phy->fields[F_CTRLCLKEN], 1);
 }
 
@@ -2321,6 +2343,10 @@ static const struct of_device_id cal_of_match[] = {
 		.compatible = "ti,dra76-cal",
 		.data = (void *)&dra76x_cal_data,
 	},
+	{
+		.compatible = "ti,am654-cal",
+		.data = (void *)&am654_cal_data,
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(of, cal_of_match);
Signature · 1 line
2.17.1
#23 lore raw

Re: [Patch v2 14/20] media: ti-vpe: cal: Add AM654 support

Hi Benoit,

Quoted 38 lines · Benoit Parrot

Add the needed control module register bit layout to support the AM654 family of devices.

---
 drivers/media/platform/Kconfig      |  2 +-
 drivers/media/platform/ti-vpe/cal.c | 28 +++++++++++++++++++++++++++-
 2 files changed, 28 insertions(+), 2 deletions(-)
drivers/media/platform/Kconfig +1 -1
index e84f35d3a68e..995f4c67f764 100644
@@ -151,7 +151,7 @@ source "drivers/media/platform/sunxi/Kconfig"
 config VIDEO_TI_CAL
 	tristate "TI CAL (Camera Adaptation Layer) driver"
 	depends on VIDEO_DEV && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
-	depends on SOC_DRA7XX || COMPILE_TEST
+	depends on SOC_DRA7XX || ARCH_K3 || COMPILE_TEST
 	select VIDEOBUF2_DMA_CONTIG
 	select V4L2_FWNODE
 	help
drivers/media/platform/ti-vpe/cal.c +8 -0
index 72ed2348389d..45653e9ed6cd 100644
@@ -322,6 +322,26 @@ static struct cal_data dra76x_cal_data = {
 	.flags = 0,
 };
 
+static struct reg_field am654_ctrl_core_csi0_reg_fields[F_MAX_FIELDS] = {
+	[F_CTRLCLKEN] = REG_FIELD(0, 15, 15),
+	[F_CAMMODE] = REG_FIELD(0, 24, 25),
+	[F_LANEENABLE] = REG_FIELD(0, 0, 4),
+};
+
+static struct cal_csi2_phy am654_cal_csi_phy[] = {
+	{

drivers/media/platform/ti-vpe/cal.c static struct cal_data dra76x_cal_data = { · line 342

Quoted 10 lines
drivers/media/platform/ti-vpe/cal.c +10 -0
+		.base_fields = am654_ctrl_core_csi0_reg_fields,
+		.num_lanes = 5,
+	},
+};
+
+static struct cal_data am654_cal_data = {
+	.csi2_phy_core = am654_cal_csi_phy,
+	.num_csi2_phy = ARRAY_SIZE(am654_cal_csi_phy),
+
+	.flags = 0,

Same comments as on 12th patch.

Could all these structs be const?

Quoted 16 lines
drivers/media/platform/ti-vpe/cal.c +5 -1
+};
+
 /*
  * there is one cal_dev structure in the driver, it is shared by
  * all instances.
@@ -548,7 +568,9 @@ static void camerarx_phy_enable(struct cal_ctx *ctx)
 	/* Always enable all lanes at the phy control level */
 	max_lanes = (1 << cal_data_get_phy_max_lanes(ctx)) - 1;
 	regmap_field_write(phy->fields[F_LANEENABLE], max_lanes);
-	regmap_field_write(phy->fields[F_CSI_MODE], 1);
+	/* F_CSI_MODE is not present on every architecture */
+	if (phy->fields[F_CSI_MODE])
+		regmap_field_write(phy->fields[F_CSI_MODE], 1);
 	regmap_field_write(phy->fields[F_CTRLCLKEN], 1);
 }
 
Signature · 3 lines
Regards,

Sakari Ailus
#24 lore raw

PATCH v2 15/20 media: ti-vpe: cal: Add subdev s_power hooks

In reply to Benoit Parrot

Based on V4L2 documentations bridge driver must power on and off sub device explicitly if media-controller mode is not used.

---
 drivers/media/platform/ti-vpe/cal.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/media/platform/ti-vpe/cal.c +12 -0
index 45653e9ed6cd..f0210a743bdc 100644
@@ -1661,6 +1661,12 @@ static int cal_start_streaming(struct vb2_queue *vq, unsigned int count)
 	if (ret < 0)
 		goto err;
 
+	ret = v4l2_subdev_call(ctx->sensor, core, s_power, 1);
+	if (ret < 0 && ret != -ENOIOCTLCMD && ret != -ENODEV) {
+		ctx_err(ctx, "power on failed in subdev\n");
+		goto err;
+	}
+
 	cal_runtime_get(ctx->dev);
 
 	csi2_ctx_config(ctx);
@@ -1674,6 +1680,7 @@ static int cal_start_streaming(struct vb2_queue *vq, unsigned int count)
 
 	ret = v4l2_subdev_call(ctx->sensor, video, s_stream, 1);
 	if (ret) {
+		v4l2_subdev_call(ctx->sensor, core, s_power, 0);
 		ctx_err(ctx, "stream on failed in subdev\n");
 		cal_runtime_put(ctx->dev);
 		goto err;
@@ -1702,6 +1709,7 @@ static void cal_stop_streaming(struct vb2_queue *vq)
 	struct cal_dmaqueue *dma_q = &ctx->vidq;
 	struct cal_buffer *buf, *tmp;
 	unsigned long flags;
+	int ret;
 
 	csi2_ppi_disable(ctx);
 	disable_irqs(ctx);
@@ -1710,6 +1718,10 @@ static void cal_stop_streaming(struct vb2_queue *vq)
 	if (v4l2_subdev_call(ctx->sensor, video, s_stream, 0))
 		ctx_err(ctx, "stream off failed in subdev\n");
 
+	ret = v4l2_subdev_call(ctx->sensor, core, s_power, 0);
+	if (ret < 0 && ret != -ENOIOCTLCMD && ret != -ENODEV)
+		ctx_err(ctx, "power off failed in subdev\n");
+
 	/* Release all active buffers */
 	spin_lock_irqsave(&ctx->slock, flags);
 	list_for_each_entry_safe(buf, tmp, &dma_q->active, list) {
Signature · 1 line
2.17.1
#25 lore raw

Re: [Patch v2 15/20] media: ti-vpe: cal: Add subdev s_power hooks

Hi Benoit,

Quoted 2 lines · Benoit Parrot

Based on V4L2 documentations bridge driver must power on and off sub device explicitly if media-controller mode is not used.

This isn't really related to MC but the fact that V4L2 still uses a V4L2-specific way to manage power state of devices that predates runtime PM.

Signature · 3 lines
Regards,

Sakari Ailus
#26 lore raw

Re: [Patch v2 15/20] media: ti-vpe: cal: Add subdev s_power hooks

Sakari Ailus <[email protected]> wrote on Wed [2019-Nov-06 11:08:39 +0200]:

Quoted 9 lines

Hi Benoit,

Quoted 2 lines · Benoit Parrot

Based on V4L2 documentations bridge driver must power on and off sub device explicitly if media-controller mode is not used.

This isn't really related to MC but the fact that V4L2 still uses a V4L2-specific way to manage power state of devices that predates runtime PM.

I'll fix the description.

Quoted 5 lines
Signature · 4 lines
-- 
Regards,

Sakari Ailus
#27 lore raw

PATCH v2 16/20 media: ti-vpe: cal: Properly calculate max resolution boundary

In reply to Benoit Parrot

Currently we were using an arbitrarily small maximum resolution mostly based on available sensor capabilities. However the hardware DMA limits are much higher than the statically define maximum resolution we were using.

There we rework the boundary check code to handle the maximum width and height based on the maximum line width in bytes and re-calculating the pixel width based on the given pixel format.

---
 drivers/media/platform/ti-vpe/cal.c | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)
drivers/media/platform/ti-vpe/cal.c +11 -5
index f0210a743bdc..20160845014e 100644
@@ -34,8 +34,8 @@
 
 #define CAL_MODULE_NAME "cal"
 
-#define MAX_WIDTH 1920
-#define MAX_HEIGHT 1200
+#define MAX_WIDTH_BYTES (8192 * 8)
+#define MAX_HEIGHT_LINES 16383
 
 #define CAL_VERSION "0.1.0"
 
@@ -1337,15 +1337,21 @@ static int cal_calc_format_size(struct cal_ctx *ctx,
 				const struct cal_fmt *fmt,
 				struct v4l2_format *f)
 {
-	u32 bpl;
+	u32 bpl, max_width;
 
 	if (!fmt) {
 		ctx_dbg(3, ctx, "No cal_fmt provided!\n");
 		return -EINVAL;
 	}
 
-	v4l_bound_align_image(&f->fmt.pix.width, 48, MAX_WIDTH, 2,
-			      &f->fmt.pix.height, 32, MAX_HEIGHT, 0, 0);
+	/*
+	 * Maximum width is bound by the DMA max width in bytes.
+	 * We need to recalculate the actual maxi width depending on the
+	 * number of bytes per pixels required.
+	 */
+	max_width = MAX_WIDTH_BYTES / (ALIGN(fmt->bpp, 8) >> 3);
+	v4l_bound_align_image(&f->fmt.pix.width, 48, max_width, 2,
+			      &f->fmt.pix.height, 32, MAX_HEIGHT_LINES, 0, 0);
 
 	bpl = (f->fmt.pix.width * ALIGN(fmt->bpp, 8)) >> 3;
 	f->fmt.pix.bytesperline = ALIGN(bpl, 16);
Signature · 1 line
2.17.1
#28 lore raw

PATCH v2 17/20 media: ti-vpe: cal: Fix a WARN issued when start streaming fails

In reply to Benoit Parrot

When start_streaming fails after the buffers have been queued we have to make sure all buffers are returned to user-space properly otherwise a v4l2 level WARN is generated.

---
 drivers/media/platform/ti-vpe/cal.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/media/platform/ti-vpe/cal.c +5 -0
index 20160845014e..cc5af830fa10 100644
@@ -1702,10 +1702,15 @@ static int cal_start_streaming(struct vb2_queue *vq, unsigned int count)
 	return 0;
 
 err:
+	spin_lock_irqsave(&ctx->slock, flags);
+	vb2_buffer_done(&ctx->cur_frm->vb.vb2_buf, VB2_BUF_STATE_QUEUED);
+	ctx->cur_frm = NULL;
+	ctx->next_frm = NULL;
 	list_for_each_entry_safe(buf, tmp, &dma_q->active, list) {
 		list_del(&buf->list);
 		vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED);
 	}
+	spin_unlock_irqrestore(&ctx->slock, flags);
 	return ret;
 }
 
Signature · 1 line
2.17.1
#29 lore raw

PATCH v2 18/20 media: ti-vpe: cal: fix enum_mbus_code/frame_size subdev arguments

In reply to Benoit Parrot

Make sure that both enum_mbus_code() and enum_framesize() properly populate the .which parameter member, otherwise -EINVAL is return causing the subdev asynchronous registration handshake to fail.

---
 drivers/media/platform/ti-vpe/cal.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/media/platform/ti-vpe/cal.c +2 -0
index cc5af830fa10..1b3b5438b76a 100644
@@ -1500,6 +1500,7 @@ static int cal_enum_framesizes(struct file *file, void *fh,
 	fse.index = fsize->index;
 	fse.pad = 0;
 	fse.code = fmt->code;
+	fse.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 
 	ret = v4l2_subdev_call(ctx->sensor, pad, enum_frame_size, NULL, &fse);
 	if (ret)
@@ -1840,6 +1841,7 @@ static int cal_async_bound(struct v4l2_async_notifier *notifier,
 
 		memset(&mbus_code, 0, sizeof(mbus_code));
 		mbus_code.index = j;
+		mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE;
 		ret = v4l2_subdev_call(subdev, pad, enum_mbus_code,
 				       NULL, &mbus_code);
 		if (ret)
Signature · 1 line
2.17.1
#30 lore raw

PATCH v2 19/20 dt-bindings: media: cal: convert binding to yaml

In reply to Benoit Parrot

Convert ti-cal.txt to ti,cal.yaml.

---
 .../devicetree/bindings/media/ti,cal.yaml     | 172 ++++++++++++++++++
 .../devicetree/bindings/media/ti-cal.txt      |  81 ---------
 2 files changed, 172 insertions(+), 81 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/ti,cal.yaml
 delete mode 100644 Documentation/devicetree/bindings/media/ti-cal.txt
Documentation/devicetree/bindings/media/ti,cal.yaml new file +172 -0
new file mode 100644
index 000000000000..d19587ea6470
@@ -0,0 +1,172 @@
+# SPDX-License-Identifier: (GPL-2.0)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/ti,cal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL) Device Tree Bindings
+
+maintainers:
+  - Benoit Parrot <[email protected]>
+
+description: |-
+  The Camera Adaptation Layer (CAL) is a key component for image capture
+  applications. The capture module provides the system interface and the
+  processing capability to connect CSI2 image-sensor modules to the
+  DRA72x device.
+
+  CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes
+  should contain a 'port' child node with child 'endpoint' node. Please
+  refer to the bindings defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+properties:
+  compatible:
+    enum:
+      # for DRA72 controllers
+      - ti,dra72-cal
+      # for DRA72 controllers pre ES2.0
+      - ti,dra72-pre-es2-cal
+      # for DRA76 controllers
+      - ti,dra76-cal
+      # for AM654 controllers
+      - ti,am654-cal
+
+  reg:
+    minItems: 2
+    items:
+      - description: The CAL main register region
+      - description: The RX Core0 (DPHY0) register region
+      - description: The RX Core1 (DPHY1) register region
+
+  reg-names:
+    minItems: 2
+    items:
+      - const: cal_top
+      - const: cal_rx_core0
+      - const: cal_rx_core1
+
+  interrupts:
+    maxItems: 1
+
+  ti,camerrx-control:
+    $ref: "/schemas/types.yaml#/definitions/phandle-array"
+    description:
+      phandle to the device control module and offset to the
+      control_camerarx_core register
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: fck
+
+  power-domains:
+    description:
+      List of phandle and PM domain specifier as documented in
+      Documentation/devicetree/bindings/power/power_domain.txt
+    maxItems: 1
+
+  # See ./video-interfaces.txt for details
+  ports:
+    type: object
+    additionalProperties: false
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+    patternProperties:
+      '^port@[0-9a-fA-F]+$':
+        type: object
+        additionalProperties: false
+
+        properties:
+          reg:
+            minItems: 1
+            items:
+              - description: The port id
+
+        patternProperties:
+          endpoint:
+            type: object
+            additionalProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              remote-endpoint: true
+
+        required:
+          - reg
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - ti,camerrx-control
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    cal: cal@4845b000 {
+        compatible = "ti,dra72-cal";
+        reg = <0x4845B000 0x400>,
+              <0x4845B800 0x40>,
+              <0x4845B900 0x40>;
+        reg-names = "cal_top",
+                    "cal_rx_core0",
+                    "cal_rx_core1";
+        interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+        ti,camerrx-control = <&scm_conf 0xE94>;
+
+        ports {
+              #address-cells = <1>;
+              #size-cells = <0>;
+
+              csi2_0: port@0 {
+                    reg = <0>;
+                    csi2_phy0: endpoint {
+                           remote-endpoint = <&csi2_cam0>;
+                           clock-lanes = <0>;
+                           data-lanes = <1 2>;
+                    };
+              };
+        };
+    };
+
+    i2c5: i2c@4807c000 {
+        clock-frequency = <400000>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera-sensor@3c {
+               compatible = "ovti,ov5640";
+               reg = <0x3c>;
+
+               clocks = <&clk_ov5640_fixed>;
+               clock-names = "xclk";
+
+               port {
+                    csi2_cam0: endpoint {
+                            remote-endpoint = <&csi2_phy0>;
+                            clock-lanes = <0>;
+                            data-lanes = <1 2>;
+                    };
+               };
+        };
+    };
+
+...
Documentation/devicetree/bindings/media/ti-cal.txt deleted +0 -81

81 lines not on this page · raw message

Signature · 1 line
2.17.1
#31 lore raw

Re: [Patch v2 19/20] dt-bindings: media: cal: convert binding to yaml

Looks like I am missing a rebase for this specific patch where I address Rob's comment about port@0 and port@1.

I'll update it in the next version.

Benoit

Benoit Parrot <[email protected]> wrote on Mon [2019-Nov-04 13:31:39 -0600]:

Quoted 278 lines

Convert ti-cal.txt to ti,cal.yaml.

---
 .../devicetree/bindings/media/ti,cal.yaml     | 172 ++++++++++++++++++
 .../devicetree/bindings/media/ti-cal.txt      |  81 ---------
 2 files changed, 172 insertions(+), 81 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/ti,cal.yaml
 delete mode 100644 Documentation/devicetree/bindings/media/ti-cal.txt
Documentation/devicetree/bindings/media/ti,cal.yaml new file +172 -0
new file mode 100644
index 000000000000..d19587ea6470
@@ -0,0 +1,172 @@
+# SPDX-License-Identifier: (GPL-2.0)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/ti,cal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL) Device Tree Bindings
+
+maintainers:
+  - Benoit Parrot <[email protected]>
+
+description: |-
+  The Camera Adaptation Layer (CAL) is a key component for image capture
+  applications. The capture module provides the system interface and the
+  processing capability to connect CSI2 image-sensor modules to the
+  DRA72x device.
+
+  CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes
+  should contain a 'port' child node with child 'endpoint' node. Please
+  refer to the bindings defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+properties:
+  compatible:
+    enum:
+      # for DRA72 controllers
+      - ti,dra72-cal
+      # for DRA72 controllers pre ES2.0
+      - ti,dra72-pre-es2-cal
+      # for DRA76 controllers
+      - ti,dra76-cal
+      # for AM654 controllers
+      - ti,am654-cal
+
+  reg:
+    minItems: 2
+    items:
+      - description: The CAL main register region
+      - description: The RX Core0 (DPHY0) register region
+      - description: The RX Core1 (DPHY1) register region
+
+  reg-names:
+    minItems: 2
+    items:
+      - const: cal_top
+      - const: cal_rx_core0
+      - const: cal_rx_core1
+
+  interrupts:
+    maxItems: 1
+
+  ti,camerrx-control:
+    $ref: "/schemas/types.yaml#/definitions/phandle-array"
+    description:
+      phandle to the device control module and offset to the
+      control_camerarx_core register
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: fck
+
+  power-domains:
+    description:
+      List of phandle and PM domain specifier as documented in
+      Documentation/devicetree/bindings/power/power_domain.txt
+    maxItems: 1
+
+  # See ./video-interfaces.txt for details
+  ports:
+    type: object
+    additionalProperties: false
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+    patternProperties:
+      '^port@[0-9a-fA-F]+$':
+        type: object
+        additionalProperties: false
+
+        properties:
+          reg:
+            minItems: 1
+            items:
+              - description: The port id
+
+        patternProperties:
+          endpoint:
+            type: object
+            additionalProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              remote-endpoint: true
+
+        required:
+          - reg
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - ti,camerrx-control
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    cal: cal@4845b000 {
+        compatible = "ti,dra72-cal";
+        reg = <0x4845B000 0x400>,
+              <0x4845B800 0x40>,
+              <0x4845B900 0x40>;
+        reg-names = "cal_top",
+                    "cal_rx_core0",
+                    "cal_rx_core1";
+        interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+        ti,camerrx-control = <&scm_conf 0xE94>;
+
+        ports {
+              #address-cells = <1>;
+              #size-cells = <0>;
+
+              csi2_0: port@0 {
+                    reg = <0>;
+                    csi2_phy0: endpoint {
+                           remote-endpoint = <&csi2_cam0>;
+                           clock-lanes = <0>;
+                           data-lanes = <1 2>;
+                    };
+              };
+        };
+    };
+
+    i2c5: i2c@4807c000 {
+        clock-frequency = <400000>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera-sensor@3c {
+               compatible = "ovti,ov5640";
+               reg = <0x3c>;
+
+               clocks = <&clk_ov5640_fixed>;
+               clock-names = "xclk";
+
+               port {
+                    csi2_cam0: endpoint {
+                            remote-endpoint = <&csi2_phy0>;
+                            clock-lanes = <0>;
+                            data-lanes = <1 2>;
+                    };
+               };
+        };
+    };
+
+...
Documentation/devicetree/bindings/media/ti-cal.txt deleted +0 -81
deleted file mode 100644
index 2deb256e7032..000000000000
@@ -1,81 +0,0 @@
-Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL)
-------------------------------------------------------
-
-The Camera Adaptation Layer (CAL) is a key component for image capture
-applications. The capture module provides the system interface and the
-processing capability to connect CSI2 image-sensor modules to the
-DRA72x device.
-
-Required properties:
-- compatible:
- Should be "ti,dra72-cal", for DRA72 controllers
- Should be "ti,dra72-pre-es2-cal", for DRA72 controllers pre ES2.0
- Should be "ti,dra76-cal", for DRA76 controllers
- Should be "ti,am654-cal", for AM654 controllers
-- reg:	CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX
-	control address space
-- reg-names: cal_top, cal_rx_core0, cal_rx_core1 and camerrx_control
-	     registers
-- interrupts: should contain IRQ line for the CAL;
-- ti,camerrx-control: phandle to the device control module and offset to
-		      the control_camerarx_core register.
-		      This node is meant to replace the "camerrx_control"
-		      reg entry above but "camerrx_control" is still
-		      handled for backward compatibility.
-
-CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes
-should contain a 'port' child node with child 'endpoint' node. Please
-refer to the bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Example:
-	cal: cal@4845b000 {
-		compatible = "ti,dra72-cal";
-		reg = <0x4845B000 0x400>,
-		      <0x4845B800 0x40>,
-		      <0x4845B900 0x40>;
-		reg-names = "cal_top",
-			    "cal_rx_core0",
-			    "cal_rx_core1";
-		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
-		ti,camerrx-control = <&scm_conf 0xE94>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			csi2_0: port@0 {
-				reg = <0>;
-				csi2_phy0: endpoint {
-					remote-endpoint = <&csi2_cam0>;
-					clock-lanes = <0>;
-					data-lanes = <1 2>;
-				};
-			};
-			csi2_1: port@1 {
-				reg = <1>;
-			};
-		};
-	};
-
-	i2c5: i2c@4807c000 {
-		clock-frequency = <400000>;
-
-		camera-sensor@3c {
-			compatible = "ovti,ov5640";
-			reg = <0x3c>;
-
-			clocks = <&clk_fixed>;
-			clock-names = "xclk";
-
-			port {
-				csi2_cam0: endpoint {
-					remote-endpoint = <&csi2_phy0>;
-					clock-lanes = <0>;
-					data-lanes = <1 2>;
-				};
-			};
-		};
-	};
Signature · 1 line
2.17.1
#32 lore raw

PATCH v2 20/20 MAINTAINERS: Add ti,cal.yaml

In reply to Benoit Parrot

Add ti,cal.yaml to the MAINTAINERS file.

---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)
MAINTAINERS +1 -0
index 8077b453f2e9..d360df48f9f2 100644
@@ -16315,6 +16315,7 @@ W:	http://linuxtv.org/
 Q:	http://patchwork.linuxtv.org/project/linux-media/list/
 S:	Maintained
 F:	drivers/media/platform/ti-vpe/
+F:	Documentation/devicetree/bindings/media/ti,cal.yaml
 
 TI WILINK WIRELESS DRIVERS
 L:	[email protected]
Signature · 1 line
2.17.1
#33 lore raw

Re: [Patch v2 20/20] MAINTAINERS: Add ti,cal.yaml

Quoted 12 lines · Benoit Parrot

Add ti,cal.yaml to the MAINTAINERS file.

---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)
MAINTAINERS +0 -0
index 8077b453f2e9..d360df48f9f2 100644

MAINTAINERS W: http://linuxtv.org/ · line 16318

Quoted 4 lines
MAINTAINERS +1 -0
@@ -16315,6 +16315,7 @@ W:	http://linuxtv.org/
 Q:	http://patchwork.linuxtv.org/project/linux-media/list/
 S:	Maintained
 F:	drivers/media/platform/ti-vpe/
+F:	Documentation/devicetree/bindings/media/ti,cal.yaml

This should be done no later than adding the file itself.

Signature · 1 line
Sakari Ailus
#34 lore raw

Re: [Patch v2 20/20] MAINTAINERS: Add ti,cal.yaml

Sakari Ailus <[email protected]> wrote on Wed [2019-Nov-06 11:10:22 +0200]:

Quoted 8 lines · Benoit Parrot
Quoted 7 lines

Add ti,cal.yaml to the MAINTAINERS file.

---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)
Quoted 11 lines

MAINTAINERS W: http://linuxtv.org/ · line 16318

Quoted 9 lines
MAINTAINERS +1 -0
index 8077b453f2e9..d360df48f9f2 100644
@@ -16315,6 +16315,7 @@ W:	http://linuxtv.org/
 Q:	http://patchwork.linuxtv.org/project/linux-media/list/
 S:	Maintained
 F:	drivers/media/platform/ti-vpe/
+F:	Documentation/devicetree/bindings/media/ti,cal.yaml

This should be done no later than adding the file itself.

Ah, but in v1 comment, Hans asked for a separate patch here. I can do it either way.

Quoted 3 lines
Signature · 2 lines
-- 
Sakari Ailus
#35 lore raw

Re: [Patch v2 20/20] MAINTAINERS: Add ti,cal.yaml

Quoted 21 lines · Benoit Parrot

Sakari Ailus <[email protected]> wrote on Wed [2019-Nov-06 11:10:22 +0200]:

Quoted 8 lines · Benoit Parrot
Quoted 7 lines

Add ti,cal.yaml to the MAINTAINERS file.

---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)
Quoted 11 lines

MAINTAINERS W: http://linuxtv.org/ · line 16318

Quoted 9 lines
MAINTAINERS +1 -0
index 8077b453f2e9..d360df48f9f2 100644
@@ -16315,6 +16315,7 @@ W:	http://linuxtv.org/
 Q:	http://patchwork.linuxtv.org/project/linux-media/list/
 S:	Maintained
 F:	drivers/media/platform/ti-vpe/
+F:	Documentation/devicetree/bindings/media/ti,cal.yaml

This should be done no later than adding the file itself.

Quoted 2 lines

Ah, but in v1 comment, Hans asked for a separate patch here. I can do it either way.

A separate patch is fine, but please arrange it before the added file.

Signature · 1 line
Sakari Ailus