Skip to contentSkip to conversation

thermal: ti-soc-thermal: Enable addition power management

PATCH In review Adam Ford 2 participants 5 messages Nov 8, 2019

Subsystems (2)
lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH 1/1 thermal: ti-soc-thermal: Enable addition power management

The bandgap sensor can be idled when the processor is too, but it isn't currently being done, so the power consumption of OMAP3 boards can elevated if the bangap sensor is enabled.

This patch attempts to use some additional power management to idle the clock to the bandgap when not needed.

drivers/thermal/ti-soc-thermal/ti-bandgap.c +43 -0
index 2fa78f738568..7a221f71bc9f 100644
@@ -26,10 +26,18 @@
 #include <linux/of_irq.h>
 #include <linux/of_gpio.h>
 #include <linux/io.h>
+#include <linux/cpu_pm.h>
+#include <linux/device.h>
+#include <linux/pm_runtime.h>
+#include <linux/pm.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
 
 #include "ti-bandgap.h"
 
 static int ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id);
+static int bandgap_omap_cpu_notifier(struct notifier_block *nb,
+				  unsigned long cmd, void *v);
 
 /***   Helper functions to access registers and their bitfields   ***/
 
@@ -1025,6 +1033,9 @@ int ti_bandgap_probe(struct platform_device *pdev)
 		}
 	}
 
+	bgp->nb.notifier_call = bandgap_omap_cpu_notifier;
+	cpu_pm_register_notifier(&bgp->nb);
+
 	return 0;
 
 remove_last_cooling:
@@ -1174,6 +1185,38 @@ static int ti_bandgap_suspend(struct device *dev)
 	return err;
 }
 
+static int bandgap_omap_cpu_notifier(struct notifier_block *nb,
+				  unsigned long cmd, void *v)
+{
+	struct ti_bandgap *bgp;
+
+	bgp = container_of(nb, struct ti_bandgap, nb);
+
+	spin_lock(&bgp->lock);
+	switch (cmd) {
+	case CPU_CLUSTER_PM_ENTER:
+		if (bgp->is_suspended)
+			break;
+		ti_bandgap_save_ctxt(bgp);
+		ti_bandgap_power(bgp, false);
+		if (TI_BANDGAP_HAS(bgp, CLK_CTRL))
+			clk_disable_unprepare(bgp->fclock);
+		break;
+	case CPU_CLUSTER_PM_ENTER_FAILED:
+	case CPU_CLUSTER_PM_EXIT:
+		if (bgp->is_suspended)
+			break;
+		if (TI_BANDGAP_HAS(bgp, CLK_CTRL))
+			clk_prepare_enable(bgp->fclock);
+		ti_bandgap_power(bgp, true);
+		ti_bandgap_restore_ctxt(bgp);
+		break;
+	}
+	spin_unlock(&bgp->lock);
+
+	return NOTIFY_OK;
+}
+
 static int ti_bandgap_resume(struct device *dev)
 {
 	struct ti_bandgap *bgp = dev_get_drvdata(dev);
drivers/thermal/ti-soc-thermal/ti-bandgap.h +6 -0
index bb9b0f7faf99..a21d07a1a23a 100644
@@ -12,6 +12,10 @@
 #include <linux/spinlock.h>
 #include <linux/types.h>
 #include <linux/err.h>
+#include <linux/cpu_pm.h>
+#include <linux/device.h>
+#include <linux/pm_runtime.h>
+#include <linux/pm.h>
 
 /**
  * DOC: bandgap driver data structure
@@ -201,6 +205,8 @@ struct ti_bandgap {
 	int				irq;
 	int				tshut_gpio;
 	u32				clk_rate;
+	struct notifier_block		nb;
+	unsigned int is_suspended:1;
 };
 
 /**
Signature · 1 line
2.20.1
#1 lore raw
Quoted 3 lines · Adam Ford

The bandgap sensor can be idled when the processor is too, but it isn't currently being done, so the power consumption of OMAP3 boards can elevated if the bangap sensor is enabled.

Great, thanks for doing this!

Quoted 2 lines

This patch attempts to use some additional power management to idle the clock to the bandgap when not needed.

Maybe add also something like this to the patch description:

As otherwise the bandgap clock blocks deeper idle states the SoC. To must idle bandgap with cpu_notifier instead of runtime PM to avoid tagging it with pm_runtime_irq_safe() that we want to stop using for drivers in general.

Quoted 2 lines
drivers/thermal/ti-soc-thermal/ti-bandgap.c +0 -0

...

Quoted 21 lines
drivers/thermal/ti-soc-thermal/ti-bandgap.c +21 -0
+static int bandgap_omap_cpu_notifier(struct notifier_block *nb,
+				  unsigned long cmd, void *v)
+{
+	struct ti_bandgap *bgp;
+
+	bgp = container_of(nb, struct ti_bandgap, nb);
+
+	spin_lock(&bgp->lock);
+	switch (cmd) {
+	case CPU_CLUSTER_PM_ENTER:
+		if (bgp->is_suspended)
+			break;
+		ti_bandgap_save_ctxt(bgp);
+		ti_bandgap_power(bgp, false);
+		if (TI_BANDGAP_HAS(bgp, CLK_CTRL))
+			clk_disable_unprepare(bgp->fclock);
+		break;
+	case CPU_CLUSTER_PM_ENTER_FAILED:
+	case CPU_CLUSTER_PM_EXIT:
+		if (bgp->is_suspended)
+			break;

drivers/thermal/ti-soc-thermal/ti-bandgap.c static int ti_bandgap_suspend(struct device *dev) · line 1218

Quoted 10 lines
drivers/thermal/ti-soc-thermal/ti-bandgap.c +10 -0
+		if (TI_BANDGAP_HAS(bgp, CLK_CTRL))
+			clk_prepare_enable(bgp->fclock);
+		ti_bandgap_power(bgp, true);
+		ti_bandgap_restore_ctxt(bgp);
+		break;
+	}
+	spin_unlock(&bgp->lock);
+
+	return NOTIFY_OK;
+}

You need to use clk_disable() and clk_enable() instead of the prepare and unprepare variants here because the prepare and unprepare variants are helpers for non-atomic context and won't necessarily work for the cpu_notifier. See the comments in include/linux/clk.h for clock_prepare_enable().

I tested this briefly with CONFIG_OMAP3_THERMAL=y and after idling the UARTs on torpedo, and it still hits off mode during idle consuming 5 - 7 mW for the main_battery_som line as measured with the shunt :) So this means we can finally then enable also CONFIG_OMAP3_THERMAL=y in the defconfigs.

Also, you may want to check if the driver needs to save and restore it's context in the notifier as that might get lost during the off mode depending what domain it's at.

Regards,

Tony

#2 lore raw
Quoted 4 lines · Tony Lindgren

Also, you may want to check if the driver needs to save and restore it's context in the notifier as that might get lost during the off mode depending what domain it's at.

Oh never mind, looks like you already took care of saving and restoring the context in the notifier, I just missed it.

Thanks,

Tony

author
#3 lore raw
Quoted 10 lines · Tony Lindgren
Quoted 4 lines · Tony Lindgren

Also, you may want to check if the driver needs to save and restore it's context in the notifier as that might get lost during the off mode depending what domain it's at.

Oh never mind, looks like you already took care of saving and restoring the context in the notifier, I just missed it.

Great!

Is there any testing you can do and think we need on the OMAP4/5+ or am33xx? I don't have any of that hardware.

I'm readying a patch without the RFC shortly.

adam

Quoted 4 lines

Thanks,

Tony

#4 lore raw
Quoted 8 lines · Adam Ford
Quoted 7 lines · Tony Lindgren
Quoted 4 lines · Tony Lindgren

Also, you may want to check if the driver needs to save and restore it's context in the notifier as that might get lost during the off mode depending what domain it's at.

Quoted 8 lines
Quoted 3 lines

Oh never mind, looks like you already took care of saving and restoring the context in the notifier, I just missed it.

Great!

Is there any testing you can do and think we need on the OMAP4/5+ or am33xx? I don't have any of that hardware.

I can test oswr idle (open switch retention) on droid4 which means save and restore of context is needed like it is for off mode.

Quoted 1 line

I'm readying a patch without the RFC shortly.

OK will give it a try and reply when done.

Regards,

Tony