Skip to contentSkip to conversation

mesh: fix (re)transmit count & interval steps

PATCH Applied Aurelien Jarno 2 participants 3 messages Nov 11, 2019 – Dec 2, 2019 Bluetooth drivers

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 mesh: fix (re)transmit count & interval steps

The Foundation Model Layer uses little endian ordering. As a consequence the (re)transmit count and interval steps in the Config Relay, Config Model Publication and Config Network Transmit messages use the lower 3 bits for the (re)transmission count and the higher 5 bits for the interval steps.

The figure 4.5 in section 4.3.2.16 of the Mesh Profile Bluetooth Specification provides a good clarification.

This patch therefore fixes those messages for both the daemon and configuration client parts.

---
 mesh/cfgmod-server.c | 16 ++++++++--------
 mesh/model.c         |  4 ++--
 tools/mesh/cfgcli.c  |  8 ++++----
 3 files changed, 14 insertions(+), 14 deletions(-)
mesh/cfgmod-server.c +8 -8
index 55cc8e9eb..8acde95b9 100644
@@ -211,8 +211,8 @@ static bool config_pub_set(struct mesh_node *node, uint16_t net_idx,
 			.ttl = ttl,
 			.credential = cred_flag,
 			.period = period,
-			.count = retransmit >> 5,
-			.interval = ((0x1f & retransmit) + 1) * 50
+			.count = retransmit & 0x7,
+			.interval = ((retransmit >> 3) + 1) * 50
 		};
 
 		if (b_virt)
@@ -870,8 +870,8 @@ static bool cfg_srv_pkt(uint16_t src, uint32_t dst, uint16_t unicast,
 		if (size != 2 || pkt[0] > 0x01)
 			return true;
 
-		count = (pkt[1] >> 5) + 1;
-		interval = ((pkt[1] & 0x1f) + 1) * 10;
+		count = (pkt[1] & 0x7) + 1;
+		interval = ((pkt[1] >> 3) + 1) * 10;
 		node_relay_mode_set(node, !!pkt[0], count, interval);
 		/* Fall Through */
 
@@ -879,7 +879,7 @@ static bool cfg_srv_pkt(uint16_t src, uint32_t dst, uint16_t unicast,
 		n = mesh_model_opcode_set(OP_CONFIG_RELAY_STATUS, msg);
 
 		msg[n++] = node_relay_mode_get(node, &count, &interval);
-		msg[n++] = ((count - 1) << 5) + ((interval/10 - 1) & 0x1f);
+		msg[n++] = (count - 1) + ((interval/10 - 1) << 3);
 
 		l_debug("Get/Set Relay Config (%d)", msg[n-1]);
 		break;
@@ -888,8 +888,8 @@ static bool cfg_srv_pkt(uint16_t src, uint32_t dst, uint16_t unicast,
 		if (size != 1)
 			return true;
 
-		count = (pkt[0] >> 5) + 1;
-		interval = ((pkt[0] & 0x1f) + 1) * 10;
+		count = (pkt[0] & 0x7) + 1;
+		interval = ((pkt[0] >> 3) + 1) * 10;
 
 		if (mesh_config_write_net_transmit(node_config_get(node), count,
 								interval))
@@ -900,7 +900,7 @@ static bool cfg_srv_pkt(uint16_t src, uint32_t dst, uint16_t unicast,
 		n = mesh_model_opcode_set(OP_CONFIG_NETWORK_TRANSMIT_STATUS,
 									msg);
 		mesh_net_transmit_params_get(net, &count, &interval);
-		msg[n++] = ((count - 1) << 5) + ((interval/10 - 1) & 0x1f);
+		msg[n++] = (count - 1) + ((interval/10 - 1) << 3);
 
 		l_debug("Get/Set Network Transmit Config");
 		break;
mesh/model.c +2 -2
index 84f1dc74c..45cdb93bb 100644
@@ -1537,8 +1537,8 @@ struct mesh_model *mesh_model_setup(struct mesh_node *node, uint8_t ele_idx,
 	if (pub && (pub->virt || !(IS_UNASSIGNED(pub->addr)))) {
 		uint8_t mod_addr[2];
 		uint8_t *pub_addr;
-		uint8_t retransmit = (pub->count << 5) +
-						(pub->interval / 50 - 1);
+		uint8_t retransmit = pub->count +
+					((pub->interval / 50 - 1) << 3);
 
 		/* Add publication */
 		l_put_le16(pub->addr, &mod_addr);
tools/mesh/cfgcli.c +4 -4
index 04edc706c..d468fb28c 100644
@@ -471,7 +471,7 @@ static bool msg_recvd(uint16_t src, uint16_t idx, uint8_t *data,
 			return true;
 
 		bt_shell_printf("Node %4.4x: Relay 0x%02x, cnt %d, steps %d\n",
-				src, data[0], data[1]>>5, data[1] & 0x1f);
+				src, data[0], data[1] & 0x7, data[1] >> 3);
 		break;
 
 	case OP_CONFIG_PROXY_STATUS:
@@ -527,8 +527,8 @@ static bool msg_recvd(uint16_t src, uint16_t idx, uint8_t *data,
 			break;
 		}
 
-		bt_shell_printf("Rexmit count\t%d\n", data[9] >> 5);
-		bt_shell_printf("Rexmit steps\t%d\n", data[9] & 0x1f);
+		bt_shell_printf("Rexmit count\t%d\n", data[9] & 0x7);
+		bt_shell_printf("Rexmit steps\t%d\n", data[9] >> 3);
 
 		break;
 
@@ -1056,7 +1056,7 @@ static void cmd_relay_set(int argc, char *argv[])
 	}
 
 	msg[n++] = parms[0];
-	msg[n++] = (parms[1] << 5) | parms[2];
+	msg[n++] = parms[1] | (parms[2] << 3);
 
 	if (!config_send(msg, n, OP_CONFIG_RELAY_SET))
 		return bt_shell_noninteractive_quit(EXIT_FAILURE);
Signature · 1 line
2.24.0
#1 lore raw
Quoted 11 lines · Aurelien Jarno

The Foundation Model Layer uses little endian ordering. As a consequence the (re)transmit count and interval steps in the Config Relay, Config Model Publication and Config Network Transmit messages use the lower 3 bits for the (re)transmission count and the higher 5 bits for the interval steps.

The figure 4.5 in section 4.3.2.16 of the Mesh Profile Bluetooth Specification provides a good clarification.

This patch therefore fixes those messages for both the daemon and configuration client parts.

Gentle ping on that patch.

Thanks,
Aurelien

Signature · 2 lines
Aurelien Jarno                          GPG: 4096R/1DDD8C9B
[email protected]                 http://www.aurel32.net
Applied
#2 lore raw
In reply to Aurelien Jarno

Applied... Thank you very much.

Quoted 120 lines · Aurelien Jarno

The Foundation Model Layer uses little endian ordering. As a consequence the (re)transmit count and interval steps in the Config Relay, Config Model Publication and Config Network Transmit messages use the lower 3 bits for the (re)transmission count and the higher 5 bits for the interval steps.

The figure 4.5 in section 4.3.2.16 of the Mesh Profile Bluetooth Specification provides a good clarification.

This patch therefore fixes those messages for both the daemon and configuration client parts.

---
 mesh/cfgmod-server.c | 16 ++++++++--------
 mesh/model.c         |  4 ++--
 tools/mesh/cfgcli.c  |  8 ++++----
 3 files changed, 14 insertions(+), 14 deletions(-)
mesh/cfgmod-server.c +8 -8
index 55cc8e9eb..8acde95b9 100644
@@ -211,8 +211,8 @@ static bool config_pub_set(struct mesh_node *node, uint16_t net_idx,
 			.ttl = ttl,
 			.credential = cred_flag,
 			.period = period,
-			.count = retransmit >> 5,
-			.interval = ((0x1f & retransmit) + 1) * 50
+			.count = retransmit & 0x7,
+			.interval = ((retransmit >> 3) + 1) * 50
 		};
 
 		if (b_virt)
@@ -870,8 +870,8 @@ static bool cfg_srv_pkt(uint16_t src, uint32_t dst, uint16_t unicast,
 		if (size != 2 || pkt[0] > 0x01)
 			return true;
 
-		count = (pkt[1] >> 5) + 1;
-		interval = ((pkt[1] & 0x1f) + 1) * 10;
+		count = (pkt[1] & 0x7) + 1;
+		interval = ((pkt[1] >> 3) + 1) * 10;
 		node_relay_mode_set(node, !!pkt[0], count, interval);
 		/* Fall Through */
 
@@ -879,7 +879,7 @@ static bool cfg_srv_pkt(uint16_t src, uint32_t dst, uint16_t unicast,
 		n = mesh_model_opcode_set(OP_CONFIG_RELAY_STATUS, msg);
 
 		msg[n++] = node_relay_mode_get(node, &count, &interval);
-		msg[n++] = ((count - 1) << 5) + ((interval/10 - 1) & 0x1f);
+		msg[n++] = (count - 1) + ((interval/10 - 1) << 3);
 
 		l_debug("Get/Set Relay Config (%d)", msg[n-1]);
 		break;
@@ -888,8 +888,8 @@ static bool cfg_srv_pkt(uint16_t src, uint32_t dst, uint16_t unicast,
 		if (size != 1)
 			return true;
 
-		count = (pkt[0] >> 5) + 1;
-		interval = ((pkt[0] & 0x1f) + 1) * 10;
+		count = (pkt[0] & 0x7) + 1;
+		interval = ((pkt[0] >> 3) + 1) * 10;
 
 		if (mesh_config_write_net_transmit(node_config_get(node), count,
 								interval))
@@ -900,7 +900,7 @@ static bool cfg_srv_pkt(uint16_t src, uint32_t dst, uint16_t unicast,
 		n = mesh_model_opcode_set(OP_CONFIG_NETWORK_TRANSMIT_STATUS,
 									msg);
 		mesh_net_transmit_params_get(net, &count, &interval);
-		msg[n++] = ((count - 1) << 5) + ((interval/10 - 1) & 0x1f);
+		msg[n++] = (count - 1) + ((interval/10 - 1) << 3);
 
 		l_debug("Get/Set Network Transmit Config");
 		break;
mesh/model.c +2 -2
index 84f1dc74c..45cdb93bb 100644
@@ -1537,8 +1537,8 @@ struct mesh_model *mesh_model_setup(struct mesh_node *node, uint8_t ele_idx,
 	if (pub && (pub->virt || !(IS_UNASSIGNED(pub->addr)))) {
 		uint8_t mod_addr[2];
 		uint8_t *pub_addr;
-		uint8_t retransmit = (pub->count << 5) +
-						(pub->interval / 50 - 1);
+		uint8_t retransmit = pub->count +
+					((pub->interval / 50 - 1) << 3);
 
 		/* Add publication */
 		l_put_le16(pub->addr, &mod_addr);
tools/mesh/cfgcli.c +4 -4
index 04edc706c..d468fb28c 100644
@@ -471,7 +471,7 @@ static bool msg_recvd(uint16_t src, uint16_t idx, uint8_t *data,
 			return true;
 
 		bt_shell_printf("Node %4.4x: Relay 0x%02x, cnt %d, steps %d\n",
-				src, data[0], data[1]>>5, data[1] & 0x1f);
+				src, data[0], data[1] & 0x7, data[1] >> 3);
 		break;
 
 	case OP_CONFIG_PROXY_STATUS:
@@ -527,8 +527,8 @@ static bool msg_recvd(uint16_t src, uint16_t idx, uint8_t *data,
 			break;
 		}
 
-		bt_shell_printf("Rexmit count\t%d\n", data[9] >> 5);
-		bt_shell_printf("Rexmit steps\t%d\n", data[9] & 0x1f);
+		bt_shell_printf("Rexmit count\t%d\n", data[9] & 0x7);
+		bt_shell_printf("Rexmit steps\t%d\n", data[9] >> 3);
 
 		break;
 
@@ -1056,7 +1056,7 @@ static void cmd_relay_set(int argc, char *argv[])
 	}
 
 	msg[n++] = parms[0];
-	msg[n++] = (parms[1] << 5) | parms[2];
+	msg[n++] = parms[1] | (parms[2] << 3);
 
 	if (!config_send(msg, n, OP_CONFIG_RELAY_SET))
 		return bt_shell_noninteractive_quit(EXIT_FAILURE);