Skip to contentSkip to conversation

dt-bindings: net: dp83869: Add TI dp83869 phy

PATCH Applied Dan Murphy 2 participants 4 messages Nov 13, 2019 – Nov 15, 2019

Subsystems (4)
lore
Share & tools
lore

Dan Murphy

author
#0 lore raw

PATCH v3 1/2 dt-bindings: net: dp83869: Add TI dp83869 phy

Add dt bindings for the TI dp83869 Gigabit ethernet phy device.

---

v3 - Moved dt-bindings header file from patch 2/2 to here

 .../devicetree/bindings/net/ti,dp83869.yaml   | 84 +++++++++++++++++++
 include/dt-bindings/net/ti-dp83869.h          | 43 ++++++++++
 2 files changed, 127 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/ti,dp83869.yaml
 create mode 100644 include/dt-bindings/net/ti-dp83869.h
Documentation/devicetree/bindings/net/ti,dp83869.yaml new file +84 -0
new file mode 100644
index 000000000000..6fe3e451da8a
@@ -0,0 +1,84 @@
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (C) 2019 Texas Instruments Incorporated
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/net/ti,dp83869.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: TI DP83869 ethernet PHY
+
+allOf:
+  - $ref: "ethernet-controller.yaml#"
+
+maintainers:
+  - Dan Murphy <[email protected]>
+
+description: |
+  The DP83869HM device is a robust, fully-featured Gigabit (PHY) transceiver
+  with integrated PMD sublayers that supports 10BASE-Te, 100BASE-TX and
+  1000BASE-T Ethernet protocols. The DP83869 also supports 1000BASE-X and
+  100BASE-FX Fiber protocols.
+  This device interfaces to the MAC layer through Reduced GMII (RGMII) and
+  SGMII The DP83869HM supports Media Conversion in Managed mode. In this mode,
+  the DP83869HM can run 1000BASE-X-to-1000BASE-T and 100BASE-FX-to-100BASE-TX
+  conversions.  The DP83869HM can also support Bridge Conversion from RGMII to
+  SGMII and SGMII to RGMII.
+
+  Specifications about the charger can be found at:
+    http://www.ti.com/lit/ds/symlink/dp83869hm.pdf
+
+properties:
+  reg:
+    maxItems: 1
+
+  ti,min-output-impedance:
+    type: boolean
+    description: |
+       MAC Interface Impedance control to set the programmable output impedance
+       to a minimum value (35 ohms).
+
+  ti,max-output-impedance:
+    type: boolean
+    description: |
+       MAC Interface Impedance control to set the programmable output impedance
+       to a maximum value (70 ohms).
+
+  tx-fifo-depth:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+       Transmitt FIFO depth see dt-bindings/net/ti-dp83869.h for values
+
+  rx-fifo-depth:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+       Receive FIFO depth see dt-bindings/net/ti-dp83869.h for values
+
+  ti,clk-output-sel:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+       Muxing option for CLK_OUT pin see dt-bindings/net/ti-dp83869.h for values.
+
+  ti,op-mode:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description: |
+       Operational mode for the PHY.  If this is not set then the operational
+       mode is set by the straps. see dt-bindings/net/ti-dp83869.h for values
+
+required:
+  - reg
+
+examples:
+  - |
+    #include <dt-bindings/net/ti-dp83869.h>
+    mdio0 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      ethphy0: ethernet-phy@0 {
+        reg = <0>;
+        tx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>;
+        rx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>;
+        ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
+        ti,max-output-impedance = "true";
+        ti,clk-output-sel = <DP83869_CLK_O_SEL_CHN_A_RCLK>;
+      };
+    };
include/dt-bindings/net/ti-dp83869.h new file +43 -0

43 lines not on this page · raw message

Signature · 1 line
2.22.0.214.g8dca754b1e
author
#1 lore raw

PATCH v3 2/2 net: phy: dp83869: Add TI dp83869 phy

Add support for the TI DP83869 Gigabit ethernet phy device.

The DP83869 is a robust, low power, fully featured Physical Layer transceiver with integrated PMD sublayers to support 10BASE-T, 100BASE-TX and 1000BASE-T Ethernet protocols.

---
 drivers/net/phy/Kconfig   |   6 +
 drivers/net/phy/Makefile  |   1 +
 drivers/net/phy/dp83869.c | 431 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 438 insertions(+)
 create mode 100644 drivers/net/phy/dp83869.c
drivers/net/phy/Kconfig +6 -0
index fe602648b99f..4f8db1bb72a8 100644
@@ -364,6 +364,12 @@ config DP83867_PHY
 	---help---
 	  Currently supports the DP83867 PHY.
 
+config DP83869_PHY
+	tristate "Texas Instruments DP83869 Gigabit PHY"
+	---help---
+	  Currently supports the DP83869 PHY.  This PHY supports copper and
+	  fiber connections.
+
 config FIXED_PHY
 	tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs"
 	depends on PHYLIB
drivers/net/phy/Makefile +1 -0
index a03437e091f3..b433ec3bf9a6 100644
@@ -70,6 +70,7 @@ obj-$(CONFIG_DP83822_PHY)	+= dp83822.o
 obj-$(CONFIG_DP83TC811_PHY)	+= dp83tc811.o
 obj-$(CONFIG_DP83848_PHY)	+= dp83848.o
 obj-$(CONFIG_DP83867_PHY)	+= dp83867.o
+obj-$(CONFIG_DP83869_PHY)	+= dp83869.o
 obj-$(CONFIG_FIXED_PHY)		+= fixed_phy.o
 obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
 obj-$(CONFIG_INTEL_XWAY_PHY)	+= intel-xway.o
drivers/net/phy/dp83869.c new file +431 -0

431 lines not on this page · raw message

Signature · 1 line
2.22.0.214.g8dca754b1e
maintainer Applied
#2 lore raw

Re: [PATCH v3 2/2] net: phy: dp83869: Add TI dp83869 phy

From: Dan Murphy <[email protected]>
Date: Wed, 13 Nov 2019 10:42:26 -0600

Quoted 9 lines

Add support for the TI DP83869 Gigabit ethernet phy device.

The DP83869 is a robust, low power, fully featured Physical Layer transceiver with integrated PMD sublayers to support 10BASE-T, 100BASE-TX and 1000BASE-T Ethernet protocols.

Applied to net-next.