Enable BeagleBone AI
cover Enable BeagleBone AI
The following patches
1) Add device tree file for BeagleBone AI
2) Minor change to dra7.dtsi
Caleb Robey (2):
ARM: dts: am5729: beaglebone-ai: adding device tree
ARM: dts: am5729: beaglebone-ai: dra7 reqs in dts
arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am5729-beagleboneai.dts | 733 ++++++++++++++++++++++ arch/arm/boot/dts/dra7.dtsi | 2 +- 3 files changed, 735 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts
Signature · 1 line
2.17.1
PATCH 1/2 ARM: dts: am5729: beaglebone-ai: adding device tree
From: Jason Kridner <[email protected]>
BeagleBoard.org BeagleBone AI is an open source hardware single board computer based on the Texas Instruments AM5729 SoC featuring dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital signal processor (DSP), quad-core embedded vision engine (EVE), Arm Cortex-M4 processors, dual programmable realtime unit industrial control subsystems and more. The board features 1GB DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash, 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion headers.
For more information, refer to:
https://beaglebone.ai
This patch introduces the BeagleBone AI device tree.
Note that the device use the "ti,tpd12s016" component which is software compatible with "ti,tpd12s015". Thus we only use the latter driver.
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am5729-beagleboneai.dts | 733 ++++++++++++++++++++++ 2 files changed, 734 insertions(+) create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -791,6 +791,7 @@ dtb-$(CONFIG_SOC_DRA7XX) += \ am57xx-beagle-x15.dtb \ am57xx-beagle-x15-revb1.dtb \ am57xx-beagle-x15-revc.dtb \ + am5729-beagleboneai.dtb \ am57xx-cl-som-am57x.dtb \ am57xx-sbc-am57x.dtb \ am572x-idk.dtb \
arch/arm/boot/dts/am5729-beagleboneai.dts new file +733 -0
733 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [uL PATCH 1/2] ARM: dts: am5729: beaglebone-ai: adding device tree
Quoted 17 lines · Caleb Robey
From: Jason Kridner <[email protected]>
BeagleBoard.org BeagleBone AI is an open source hardware single board computer based on the Texas Instruments AM5729 SoC featuring dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital signal processor (DSP), quad-core embedded vision engine (EVE), Arm Cortex-M4 processors, dual programmable realtime unit industrial control subsystems and more. The board features 1GB DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash, 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion headers.
For more information, refer to:
https://beaglebone.aiThis patch introduces the BeagleBone AI device tree.
Quoted 7 lines
Note that the device use the "ti,tpd12s016" component which is software compatible with "ti,tpd12s015". Thus we only use the latter driver.
Signed-off-by Jason Kridner <[email protected]>Cc Robert Nelson <[email protected]>Cc Caleb Robey <[email protected]>
Hmm so this one has "From: Jason Kridner <[email protected]>", but seems like you may have updated it and are sending it out, so it probably should also have your Signed-off-by.
Note that you can summarize your additions with something like:
Regards,
Tony
PATCH 2/2 ARM: dts: am5729: beaglebone-ai: dra7 reqs in dts
In reply to Caleb RobeySmall nomenclature change for beaglebone AI compatibility.
--- arch/arm/boot/dts/dra7.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/dra7.dtsi +1 -1
@@ -143,7 +143,7 @@ * the moment, just use a fake OCP bus entry to represent the whole bus * hierarchy. */ - ocp { + ocp: ocp { compatible = "ti,dra7-l3-noc", "simple-bus"; #address-cells = <1>; #size-cells = <1>;
Signature · 1 line
2.17.1
Re: [uL PATCH 2/2] ARM: dts: am5729: beaglebone-ai: dra7 reqs in dts
Quoted 3 lines · Caleb Robey
Small nomenclature change for beaglebone AI compatibility.
Signed-off-by Jason Kridner <[email protected]>
Hmm so should this patch be also "From: Jason Kridner <[email protected]>" if Jason's patch?
If so, please resend, and since you're the one sending it, please also add your Signed-off-by.
Thanks,
Tony
Quoted 19 lines
arch/arm/boot/dts/dra7.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/boot/dts/dra7.dtsi +1
-1@@ -143,7 +143,7 @@ * the moment, just use a fake OCP bus entry to represent the whole bus * hierarchy. */ - ocp { + ocp: ocp { compatible = "ti,dra7-l3-noc", "simple-bus"; #address-cells = <1>; #size-cells = <1>;Signature · 1 line
2.17.1