ARM: dts: exynos5420: add mali dt node and enable mali on Odroid XU3/4
Subsystems (2)
PATCH v6 1/1 ARM: dts: exynos5420: add mali dt node and enable mali on Odroid XU3/4
Add device tree node for Mali GPU for Exynos 542x SoC. GPU is disabled by default, and is enabled for each board after the regulator is defined. Tested on Odroid-XU4.
---
Changes since v5:
- fixed compile warnings
Changes since v4:
- fixed so it applies for latest 5.4-rc7
Changes since v3:
- fixed compatible to match bindings
Changes since v2:
- separate patch for bindings
- fixed bindings typo
Changes since v1:
- used generic node and label for GPU
- added bindings for compatible
- fixed irq indentation
- fixed interrupt-names to match bindings
- added cooling cells for future TMU connection
- used generic node and label for GPU opp table
- removed always-on from SoC GPU regulator
--- arch/arm/boot/dts/exynos5420.dtsi | 50 +++++++++++++++++++++++++++ arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 6 +++- 2 files changed, 55 insertions(+), 1 deletion(-)
arch/arm/boot/dts/exynos5420.dtsi +50 -0
@@ -670,6 +670,56 @@ iommus = <&sysmmu_gscl1>; }; + gpu: gpu@11800000 { + compatible = "samsung,exynos5420-mali", "arm,mali-t628"; + reg = <0x11800000 0x5000>; + interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "job", "mmu", "gpu"; + + clocks = <&clock CLK_G3D>; + clock-names = "core"; + power-domains = <&g3d_pd>; + operating-points-v2 = <&gpu_opp_table>; + + status = "disabled"; + #cooling-cells = <2>; + + gpu_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-177000000 { + opp-hz = /bits/ 64 <177000000>; + opp-microvolt = <812500>; + }; + opp-266000000 { + opp-hz = /bits/ 64 <266000000>; + opp-microvolt = <862500>; + }; + opp-350000000 { + opp-hz = /bits/ 64 <350000000>; + opp-microvolt = <912500>; + }; + opp-420000000 { + opp-hz = /bits/ 64 <420000000>; + opp-microvolt = <962500>; + }; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <1000000>; + }; + opp-543000000 { + opp-hz = /bits/ 64 <543000000>; + opp-microvolt = <1037500>; + }; + opp-600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1150000>; + }; + }; + }; + scaler_0: scaler@12800000 { compatible = "samsung,exynos5420-scaler"; reg = <0x12800000 0x1294>;
arch/arm/boot/dts/exynos5422-odroid-core.dtsi +5 -1
@@ -522,7 +522,6 @@ regulator-name = "vdd_g3d"; regulator-min-microvolt = <800000>; regulator-max-microvolt = <1400000>; - regulator-always-on; regulator-boot-on; regulator-state-mem {
@@ -654,6 +653,11 @@ vtmu-supply = <&ldo7_reg>; }; +&gpu { + mali-supply = <&buck4_reg>; + status = "okay"; +}; + &rtc { status = "okay"; clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
Signature · 1 line
2.14.1
Quoted 29 lines · Marian Mihailescu
Add device tree node for Mali GPU for Exynos 542x SoC. GPU is disabled by default, and is enabled for each board after the regulator is defined. Tested on Odroid-XU4.
Signed-off-by Marian Mihailescu <[email protected]>---
Changes since v5:
- fixed compile warningsChanges since v4:
- fixed so it applies for latest 5.4-rc7Changes since v3:
- fixed compatible to match bindingsChanges since v2:
- separate patch for bindings
- fixed bindings typoChanges since v1:
- used generic node and label for GPU
- added bindings for compatible
- fixed irq indentation
- fixed interrupt-names to match bindings
- added cooling cells for future TMU connection
- used generic node and label for GPU opp table
- removed always-on from SoC GPU regulator
Quoted 3 lines
--- arch/arm/boot/dts/exynos5420.dtsi | 50 +++++++++++++++++++++++++++ arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 6 +++-
Thanks, applied.
Best regards,
Krzysztof