Skip to contentSkip to conversation

Add support for H6 PWM

PATCH Superseded Clément Péron 2 participants 14 messages Nov 21, 2019 – Nov 23, 2019

Subsystems (2)

v8 of 9 Superseded Latest is v9 →

lore
Share & tools
lore
#0 lore raw

v8 cover Add support for H6 PWM

Hi,

This is a rework of Jernej's previous work[1] taking account all the previous remarks.

Bindings is still strict but probe in the driver are now optionnals.

If someone could confirm that the PWM is not broken, as my board doesn't output it.

Thanks,
Clément

Jernej's cover:
Allwinner H6 SoC has PWM core which is basically the same as that found in A20, it's just depends on additional bus clock and reset line.

This series adds support for it and extends PWM driver functionality in a way that it's now possible to bypass whole core and output PWM source clock directly as a PWM signal. This functionality is needed by AC200 chip, which is bundled in same physical package as H6 SoC, to serve as a clock source of 24 MHz. AC200 clock input pin is bonded internally to the second PWM channel.

I would be grateful if anyone can test this patch series for any kind of regression on other SoCs.

[1]: https://patchwork.kernel.org/cover/11061737/

Changes in v8:
- Display error return code
- split commit
- bypass is false if unsupported
- return instead of goto

Changes in v7:
- Fix indent in Yaml bindings

Changes in v6:
- Update git commit log
- Distinguish error message

Changes in v5:
- Move bypass calculation to pwm_calculate
- Split mod_clock fallback from bus_clk probe
- Update comment
- Move my SoB after acked-by/reviewed-by

Changes in v4:
- item description in correct order and add a blank line
- use %pe for printing PTR_ERR
- don't print error when it's an EPROBE_DEFER
- change output clock bypass formula to match PWM policy

Changes in v3:
- Documentation update to allow one clock without name
- Change reset optional to shared
- If reset probe failed return an error
- Remove old clock probe
- Update bypass enabled formula

Changes in v2:
- Remove allOf in Documentation
- Add H6 example in Documentation
- Change clock name from "pwm" to "mod"
- Change reset quirk to optional probe
- Change bus_clock quirk to optional probe
- Add limitation comment about mod_clk_output
- Add quirk for mod_clk_output
- Change bypass formula

Clément Péron (2):
pwm: sun4i: Prefer "mod" clock to unnamed
pwm: sun4i: Always calculate params when applying new parameters

Jernej Skrabec (4):
pwm: sun4i: Add an optional probe for reset line
pwm: sun4i: Add an optional probe for bus clock
pwm: sun4i: Add support to output source clock directly
pwm: sun4i: Add support for H6 PWM

 drivers/pwm/pwm-sun4i.c | 187 +++++++++++++++++++++++++++++++++-------
 1 file changed, 156 insertions(+), 31 deletions(-)
Signature · 6 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20191121195902.6906-1-peron.clem%40gmail.com.
#1 lore raw

PATCH v8 1/6 pwm: sun4i: Add an optional probe for reset line

From: Jernej Skrabec <[email protected]>

H6 PWM core needs deasserted reset line in order to work.

Add an optional probe for it.

---
 drivers/pwm/pwm-sun4i.c | 34 ++++++++++++++++++++++++++++++++--
 1 file changed, 32 insertions(+), 2 deletions(-)
drivers/pwm/pwm-sun4i.c +32 -2
index 581d23287333..e353a03ec614 100644
@@ -16,6 +16,7 @@
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/pwm.h>
+#include <linux/reset.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
 #include <linux/time.h>
@@ -78,6 +79,7 @@ struct sun4i_pwm_data {
 struct sun4i_pwm_chip {
 	struct pwm_chip chip;
 	struct clk *clk;
+	struct reset_control *rst;
 	void __iomem *base;
 	spinlock_t ctrl_lock;
 	const struct sun4i_pwm_data *data;
@@ -364,6 +366,22 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 	if (IS_ERR(pwm->clk))
 		return PTR_ERR(pwm->clk);
 
+	pwm->rst = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
+	if (IS_ERR(pwm->rst)) {
+		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "get reset failed %pe\n",
+				pwm->rst);
+		return PTR_ERR(pwm->rst);
+	}
+
+	/* Deassert reset */
+	ret = reset_control_deassert(pwm->rst);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot deassert reset control: %d\n",
+			ret);
+		return ret;
+	}
+
 	pwm->chip.dev = &pdev->dev;
 	pwm->chip.ops = &sun4i_pwm_ops;
 	pwm->chip.base = -1;
@@ -376,19 +394,31 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 	ret = pwmchip_add(&pwm->chip);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "failed to add PWM chip: %d\n", ret);
-		return ret;
+		goto err_pwm_add;
 	}
 
 	platform_set_drvdata(pdev, pwm);
 
 	return 0;
+
+err_pwm_add:
+	reset_control_assert(pwm->rst);
+
+	return ret;
 }
 
 static int sun4i_pwm_remove(struct platform_device *pdev)
 {
 	struct sun4i_pwm_chip *pwm = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = pwmchip_remove(&pwm->chip);
+	if (ret)
+		return ret;
+
+	reset_control_assert(pwm->rst);
 
-	return pwmchip_remove(&pwm->chip);
+	return 0;
 }
 
 static struct platform_driver sun4i_pwm_driver = {
Signature · 6 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20191121195902.6906-2-peron.clem%40gmail.com.
#2 lore raw

PATCH v8 2/6 pwm: sun4i: Prefer "mod" clock to unnamed

In reply to Clément Péron

New device tree bindings called the source clock of the module "mod" when several clocks are defined.

Try to get a clock called "mod" if nothing is found try to get an unnamed clock.

---
 drivers/pwm/pwm-sun4i.c | 29 +++++++++++++++++++++++++++--
 1 file changed, 27 insertions(+), 2 deletions(-)
drivers/pwm/pwm-sun4i.c +27 -2
index e353a03ec614..369990ae7d09 100644
@@ -362,9 +362,34 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 	if (IS_ERR(pwm->base))
 		return PTR_ERR(pwm->base);
 
-	pwm->clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(pwm->clk))
+	/*
+	 * All hardware variants need a source clock that is divided and
+	 * then feeds the counter that defines the output wave form. In the
+	 * device tree this clock is either unnamed or called "mod".
+	 * Some variants (e.g. H6) need another clock to access the
+	 * hardware registers; this is called "bus".
+	 * So we request "mod" first (and ignore the corner case that a
+	 * parent provides a "mod" clock while the right one would be the
+	 * unnamed one of the PWM device) and if this is not found we fall
+	 * back to the first clock of the PWM.
+	 */
+	pwm->clk = devm_clk_get_optional(&pdev->dev, "mod");
+	if (IS_ERR(pwm->clk)) {
+		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "get mod clock failed %pe\n",
+				pwm->clk);
 		return PTR_ERR(pwm->clk);
+	}
+
+	if (!pwm->clk) {
+		pwm->clk = devm_clk_get(&pdev->dev, NULL);
+		if (IS_ERR(pwm->clk)) {
+			if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "get unnamed clock failed %pe\n",
+					pwm->clk);
+			return PTR_ERR(pwm->clk);
+		}
+	}
 
 	pwm->rst = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
 	if (IS_ERR(pwm->rst)) {
Signature · 6 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20191121195902.6906-3-peron.clem%40gmail.com.
#3 lore raw

PATCH v8 3/6 pwm: sun4i: Add an optional probe for bus clock

In reply to Clément Péron

From: Jernej Skrabec <[email protected]>

H6 PWM core needs bus clock to be enabled in order to work.

Add an optional probe for it.

---
 drivers/pwm/pwm-sun4i.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)
drivers/pwm/pwm-sun4i.c +23 -0
index 369990ae7d09..66befd8d6f9c 100644
@@ -78,6 +78,7 @@ struct sun4i_pwm_data {
 
 struct sun4i_pwm_chip {
 	struct pwm_chip chip;
+	struct clk *bus_clk;
 	struct clk *clk;
 	struct reset_control *rst;
 	void __iomem *base;
@@ -391,6 +392,14 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 		}
 	}
 
+	pwm->bus_clk = devm_clk_get_optional(&pdev->dev, "bus");
+	if (IS_ERR(pwm->bus_clk)) {
+		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "get bus clock failed %pe\n",
+				pwm->bus_clk);
+		return PTR_ERR(pwm->bus_clk);
+	}
+
 	pwm->rst = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
 	if (IS_ERR(pwm->rst)) {
 		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
@@ -407,6 +416,17 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	/*
+	 * We're keeping the bus clock on for the sake of simplicity.
+	 * Actually it only needs to be on for hardware register accesses.
+	 */
+	ret = clk_prepare_enable(pwm->bus_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot prepare and enable bus_clk %d\n",
+			ret);
+		goto err_bus;
+	}
+
 	pwm->chip.dev = &pdev->dev;
 	pwm->chip.ops = &sun4i_pwm_ops;
 	pwm->chip.base = -1;
@@ -427,6 +447,8 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 	return 0;
 
 err_pwm_add:
+	clk_disable_unprepare(pwm->bus_clk);
+err_bus:
 	reset_control_assert(pwm->rst);
 
 	return ret;
@@ -441,6 +463,7 @@ static int sun4i_pwm_remove(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
+	clk_disable_unprepare(pwm->bus_clk);
 	reset_control_assert(pwm->rst);
 
 	return 0;
Signature · 6 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20191121195902.6906-4-peron.clem%40gmail.com.
#4 lore raw

Re: [PATCH v8 3/6] pwm: sun4i: Add an optional probe for bus clock

Quoted 41 lines · Clément Péron

From: Jernej Skrabec <[email protected]>

H6 PWM core needs bus clock to be enabled in order to work.

Add an optional probe for it.

---
 drivers/pwm/pwm-sun4i.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)
drivers/pwm/pwm-sun4i.c +9 -0
index 369990ae7d09..66befd8d6f9c 100644
@@ -78,6 +78,7 @@ struct sun4i_pwm_data {
 
 struct sun4i_pwm_chip {
 	struct pwm_chip chip;
+	struct clk *bus_clk;
 	struct clk *clk;
 	struct reset_control *rst;
 	void __iomem *base;
@@ -391,6 +392,14 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 		}
 	}
 
+	pwm->bus_clk = devm_clk_get_optional(&pdev->dev, "bus");
+	if (IS_ERR(pwm->bus_clk)) {
+		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "get bus clock failed %pe\n",
+				pwm->bus_clk);
+		return PTR_ERR(pwm->bus_clk);
+	}
+
 	pwm->rst = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
 	if (IS_ERR(pwm->rst)) {
 		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
@@ -407,6 +416,17 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 		return ret;

drivers/pwm/pwm-sun4i.c static int sun4i_pwm_probe(struct platform_device *pdev) · line 426

Quoted 10 lines
drivers/pwm/pwm-sun4i.c +8 -0
 	}
 
+	/*
+	 * We're keeping the bus clock on for the sake of simplicity.
+	 * Actually it only needs to be on for hardware register accesses.
+	 */
+	ret = clk_prepare_enable(pwm->bus_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot prepare and enable bus_clk %d\n",
+			ret);

nitpick: other error messages in this driver start with a lower case letter.

Until there is an equivalent for %pe that consumes an int, I suggest to use

	dev_err(&pdev->dev, "Cannot prepare and enable bus_clk: %pe\n",
	        ERR_PTR(ret));

to benefit from a symbolic error name instead of an error constant.

Best regards
Uwe

Signature · 2 lines
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |
#5 lore raw

Re: [PATCH v8 3/6] pwm: sun4i: Add an optional probe for bus clock

Hi Uwe,

Quoted 57 lines · Uwe Kleine-König
Quoted 41 lines · Clément Péron

From: Jernej Skrabec <[email protected]>

H6 PWM core needs bus clock to be enabled in order to work.

Add an optional probe for it.

---
 drivers/pwm/pwm-sun4i.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)
drivers/pwm/pwm-sun4i.c +9 -0
index 369990ae7d09..66befd8d6f9c 100644
@@ -78,6 +78,7 @@ struct sun4i_pwm_data {
 
 struct sun4i_pwm_chip {
      struct pwm_chip chip;
+     struct clk *bus_clk;
      struct clk *clk;
      struct reset_control *rst;
      void __iomem *base;
@@ -391,6 +392,14 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
              }
      }
 
+     pwm->bus_clk = devm_clk_get_optional(&pdev->dev, "bus");
+     if (IS_ERR(pwm->bus_clk)) {
+             if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
+                     dev_err(&pdev->dev, "get bus clock failed %pe\n",
+                             pwm->bus_clk);
+             return PTR_ERR(pwm->bus_clk);
+     }
+
      pwm->rst = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
      if (IS_ERR(pwm->rst)) {
              if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
@@ -407,6 +416,17 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
              return ret;

drivers/pwm/pwm-sun4i.c static int sun4i_pwm_probe(struct platform_device *pdev) · line 426

Quoted 10 lines
drivers/pwm/pwm-sun4i.c +8 -0
      }
 
+     /*
+      * We're keeping the bus clock on for the sake of simplicity.
+      * Actually it only needs to be on for hardware register accesses.
+      */
+     ret = clk_prepare_enable(pwm->bus_clk);
+     if (ret) {
+             dev_err(&pdev->dev, "Cannot prepare and enable bus_clk %d\n",
+                     ret);

nitpick: other error messages in this driver start with a lower case letter.

Quoted 7 lines

Until there is an equivalent for %pe that consumes an int, I suggest to use

        dev_err(&pdev->dev, "Cannot prepare and enable bus_clk: %pe\n",
                ERR_PTR(ret));

to benefit from a symbolic error name instead of an error constant.

Ok i will fix both

Thanks,
Clement

Quoted 7 lines

Best regards
Uwe

--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | https://www.pengutronix.de/ |

Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCcfj7rngTgbZQDwjKoLgRGcqsYscBvrCP095zzyASKSqdQ%40mail.gmail.com.
#6 lore raw

PATCH v8 4/6 pwm: sun4i: Always calculate params when applying new parameters

In reply to Clément Péron

Bypass mode will require to be re-calculated when the pwm state is changed.

Remove the condition so pwm_sun4i_calculate is always called.

---
 drivers/pwm/pwm-sun4i.c | 52 ++++++++++++++++++-----------------------
 1 file changed, 23 insertions(+), 29 deletions(-)
drivers/pwm/pwm-sun4i.c +23 -29
index 66befd8d6f9c..1fa2057419fb 100644
@@ -202,9 +202,9 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 {
 	struct sun4i_pwm_chip *sun4i_pwm = to_sun4i_pwm_chip(chip);
 	struct pwm_state cstate;
-	u32 ctrl;
+	u32 ctrl, duty, period, val;
 	int ret;
-	unsigned int delay_us;
+	unsigned int delay_us, prescaler;
 	unsigned long now;
 
 	pwm_get_state(pwm, &cstate);
@@ -220,43 +220,37 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 	spin_lock(&sun4i_pwm->ctrl_lock);
 	ctrl = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
-	if ((cstate.period != state->period) ||
-	    (cstate.duty_cycle != state->duty_cycle)) {
-		u32 period, duty, val;
-		unsigned int prescaler;
-
-		ret = sun4i_pwm_calculate(sun4i_pwm, state,
-					  &duty, &period, &prescaler);
-		if (ret) {
-			dev_err(chip->dev, "period exceeds the maximum value\n");
-			spin_unlock(&sun4i_pwm->ctrl_lock);
-			if (!cstate.enabled)
-				clk_disable_unprepare(sun4i_pwm->clk);
-			return ret;
-		}
-
-		if (PWM_REG_PRESCAL(ctrl, pwm->hwpwm) != prescaler) {
-			/* Prescaler changed, the clock has to be gated */
-			ctrl &= ~BIT_CH(PWM_CLK_GATING, pwm->hwpwm);
-			sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
+	ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler);
+	if (ret) {
+		dev_err(chip->dev, "period exceeds the maximum value\n");
+		spin_unlock(&sun4i_pwm->ctrl_lock);
+		if (!cstate.enabled)
+			clk_disable_unprepare(sun4i_pwm->clk);
+		return ret;
+	}
 
-			ctrl &= ~BIT_CH(PWM_PRESCAL_MASK, pwm->hwpwm);
-			ctrl |= BIT_CH(prescaler, pwm->hwpwm);
-		}
+	if (PWM_REG_PRESCAL(ctrl, pwm->hwpwm) != prescaler) {
+		/* Prescaler changed, the clock has to be gated */
+		ctrl &= ~BIT_CH(PWM_CLK_GATING, pwm->hwpwm);
+		sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
 
-		val = (duty & PWM_DTY_MASK) | PWM_PRD(period);
-		sun4i_pwm_writel(sun4i_pwm, val, PWM_CH_PRD(pwm->hwpwm));
-		sun4i_pwm->next_period[pwm->hwpwm] = jiffies +
-			usecs_to_jiffies(cstate.period / 1000 + 1);
-		sun4i_pwm->needs_delay[pwm->hwpwm] = true;
+		ctrl &= ~BIT_CH(PWM_PRESCAL_MASK, pwm->hwpwm);
+		ctrl |= BIT_CH(prescaler, pwm->hwpwm);
 	}
 
+	val = (duty & PWM_DTY_MASK) | PWM_PRD(period);
+	sun4i_pwm_writel(sun4i_pwm, val, PWM_CH_PRD(pwm->hwpwm));
+	sun4i_pwm->next_period[pwm->hwpwm] = jiffies +
+		usecs_to_jiffies(cstate.period / 1000 + 1);
+	sun4i_pwm->needs_delay[pwm->hwpwm] = true;
+
 	if (state->polarity != PWM_POLARITY_NORMAL)
 		ctrl &= ~BIT_CH(PWM_ACT_STATE, pwm->hwpwm);
 	else
 		ctrl |= BIT_CH(PWM_ACT_STATE, pwm->hwpwm);
 
 	ctrl |= BIT_CH(PWM_CLK_GATING, pwm->hwpwm);
+
 	if (state->enabled) {
 		ctrl |= BIT_CH(PWM_EN, pwm->hwpwm);
 	} else if (!sun4i_pwm->needs_delay[pwm->hwpwm]) {
Signature · 6 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20191121195902.6906-5-peron.clem%40gmail.com.
Reviewed-by on v8 4/6
#7 lore raw

Re: [PATCH v8 4/6] pwm: sun4i: Always calculate params when applying new parameters

Quoted 6 lines · Clément Péron

Bypass mode will require to be re-calculated when the pwm state is changed.

Remove the condition so pwm_sun4i_calculate is always called.

When applying this patch and looking at it using git show -b it is obvious the patch does exactly what is promised here. (Apart from the introduced empty line in the last hunk which is ok in my book.)

Thanks
Uwe

Signature · 2 lines
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |
#8 lore raw

PATCH v8 5/6 pwm: sun4i: Add support to output source clock directly

In reply to Clément Péron

From: Jernej Skrabec <[email protected]>

PWM core has an option to bypass whole logic and output unchanged source clock as PWM output. This is achieved by enabling bypass bit.

Note that when bypass is enabled, no other setting has any meaning, not even enable bit.

This mode of operation is needed to achieve high enough frequency to serve as clock source for AC200 chip which is integrated into same package as H6 SoC.

---
 drivers/pwm/pwm-sun4i.c | 48 +++++++++++++++++++++++++++++++++++++++--
 1 file changed, 46 insertions(+), 2 deletions(-)
drivers/pwm/pwm-sun4i.c +46 -2
index 1fa2057419fb..0fe9c680d6d0 100644
@@ -3,6 +3,10 @@
  * Driver for Allwinner sun4i Pulse Width Modulation Controller
  *
  * Copyright (C) 2014 Alexandre Belloni <[email protected]>
+ *
+ * Limitations:
+ * - When outputing the source clock directly, the PWM logic will be bypassed
+ *   and the currently running period is not guaranteed to be completed
  */
 
 #include <linux/bitops.h>
@@ -73,6 +77,7 @@ static const u32 prescaler_table[] = {
 
 struct sun4i_pwm_data {
 	bool has_prescaler_bypass;
+	bool has_direct_mod_clk_output;
 	unsigned int npwm;
 };
 
@@ -118,6 +123,20 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
 	val = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
+	/*
+	 * PWM chapter in H6 manual has a diagram which explains that if bypass
+	 * bit is set, no other setting has any meaning. Even more, experiment
+	 * proved that also enable bit is ignored in this case.
+	 */
+	if ((val & BIT_CH(PWM_BYPASS, pwm->hwpwm)) &&
+	    sun4i_pwm->data->has_direct_mod_clk_output) {
+		state->period = DIV_ROUND_UP_ULL(NSEC_PER_SEC, clk_rate);
+		state->duty_cycle = DIV_ROUND_UP_ULL(state->period, 2);
+		state->polarity = PWM_POLARITY_NORMAL;
+		state->enabled = true;
+		return;
+	}
+
 	if ((PWM_REG_PRESCAL(val, pwm->hwpwm) == PWM_PRESCAL_MASK) &&
 	    sun4i_pwm->data->has_prescaler_bypass)
 		prescaler = 1;
@@ -149,13 +168,24 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
 static int sun4i_pwm_calculate(struct sun4i_pwm_chip *sun4i_pwm,
 			       const struct pwm_state *state,
-			       u32 *dty, u32 *prd, unsigned int *prsclr)
+			       u32 *dty, u32 *prd, unsigned int *prsclr,
+			       bool *bypass)
 {
 	u64 clk_rate, div = 0;
 	unsigned int pval, prescaler = 0;
 
 	clk_rate = clk_get_rate(sun4i_pwm->clk);
 
+	*bypass = sun4i_pwm->data->has_direct_mod_clk_output &&
+		  state->enabled &&
+		  (state->period * clk_rate >= NSEC_PER_SEC) &&
+		  (state->period * clk_rate < 2 * NSEC_PER_SEC) &&
+		  (state->duty_cycle * clk_rate * 2 >= NSEC_PER_SEC);
+
+	/* Skip calculation of other parameters if we bypass them */
+	if (*bypass)
+		return 0;
+
 	if (sun4i_pwm->data->has_prescaler_bypass) {
 		/* First, test without any prescaler when available */
 		prescaler = PWM_PRESCAL_MASK;
@@ -206,6 +236,7 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 	int ret;
 	unsigned int delay_us, prescaler;
 	unsigned long now;
+	bool bypass;
 
 	pwm_get_state(pwm, &cstate);
 
@@ -220,7 +251,8 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 	spin_lock(&sun4i_pwm->ctrl_lock);
 	ctrl = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
-	ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler);
+	ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler,
+				  &bypass);
 	if (ret) {
 		dev_err(chip->dev, "period exceeds the maximum value\n");
 		spin_unlock(&sun4i_pwm->ctrl_lock);
@@ -229,6 +261,18 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 		return ret;
 	}
 
+	if (sun4i_pwm->data->has_direct_mod_clk_output) {
+		if (bypass) {
+			ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
+			/* We can skip other parameter */
+			sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
+			spin_unlock(&sun4i_pwm->ctrl_lock);
+			return 0;
+		} else {
+			ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
+		}
+	}
+
 	if (PWM_REG_PRESCAL(ctrl, pwm->hwpwm) != prescaler) {
 		/* Prescaler changed, the clock has to be gated */
 		ctrl &= ~BIT_CH(PWM_CLK_GATING, pwm->hwpwm);
Signature · 6 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20191121195902.6906-6-peron.clem%40gmail.com.
#9 lore raw

Re: [PATCH v8 5/6] pwm: sun4i: Add support to output source clock directly

Quoted 111 lines · Clément Péron

From: Jernej Skrabec <[email protected]>

PWM core has an option to bypass whole logic and output unchanged source clock as PWM output. This is achieved by enabling bypass bit.

Note that when bypass is enabled, no other setting has any meaning, not even enable bit.

This mode of operation is needed to achieve high enough frequency to serve as clock source for AC200 chip which is integrated into same package as H6 SoC.

---
 drivers/pwm/pwm-sun4i.c | 48 +++++++++++++++++++++++++++++++++++++++--
 1 file changed, 46 insertions(+), 2 deletions(-)
drivers/pwm/pwm-sun4i.c +35 -2
index 1fa2057419fb..0fe9c680d6d0 100644
@@ -3,6 +3,10 @@
  * Driver for Allwinner sun4i Pulse Width Modulation Controller
  *
  * Copyright (C) 2014 Alexandre Belloni <[email protected]>
+ *
+ * Limitations:
+ * - When outputing the source clock directly, the PWM logic will be bypassed
+ *   and the currently running period is not guaranteed to be completed
  */
 
 #include <linux/bitops.h>
@@ -73,6 +77,7 @@ static const u32 prescaler_table[] = {
 
 struct sun4i_pwm_data {
 	bool has_prescaler_bypass;
+	bool has_direct_mod_clk_output;
 	unsigned int npwm;
 };
 
@@ -118,6 +123,20 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
 	val = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
+	/*
+	 * PWM chapter in H6 manual has a diagram which explains that if bypass
+	 * bit is set, no other setting has any meaning. Even more, experiment
+	 * proved that also enable bit is ignored in this case.
+	 */
+	if ((val & BIT_CH(PWM_BYPASS, pwm->hwpwm)) &&
+	    sun4i_pwm->data->has_direct_mod_clk_output) {
+		state->period = DIV_ROUND_UP_ULL(NSEC_PER_SEC, clk_rate);
+		state->duty_cycle = DIV_ROUND_UP_ULL(state->period, 2);
+		state->polarity = PWM_POLARITY_NORMAL;
+		state->enabled = true;
+		return;
+	}
+
 	if ((PWM_REG_PRESCAL(val, pwm->hwpwm) == PWM_PRESCAL_MASK) &&
 	    sun4i_pwm->data->has_prescaler_bypass)
 		prescaler = 1;
@@ -149,13 +168,24 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
 static int sun4i_pwm_calculate(struct sun4i_pwm_chip *sun4i_pwm,
 			       const struct pwm_state *state,
-			       u32 *dty, u32 *prd, unsigned int *prsclr)
+			       u32 *dty, u32 *prd, unsigned int *prsclr,
+			       bool *bypass)
 {
 	u64 clk_rate, div = 0;
 	unsigned int pval, prescaler = 0;
 
 	clk_rate = clk_get_rate(sun4i_pwm->clk);
 
+	*bypass = sun4i_pwm->data->has_direct_mod_clk_output &&
+		  state->enabled &&
+		  (state->period * clk_rate >= NSEC_PER_SEC) &&
+		  (state->period * clk_rate < 2 * NSEC_PER_SEC) &&
+		  (state->duty_cycle * clk_rate * 2 >= NSEC_PER_SEC);
+
+	/* Skip calculation of other parameters if we bypass them */
+	if (*bypass)
+		return 0;
+
 	if (sun4i_pwm->data->has_prescaler_bypass) {
 		/* First, test without any prescaler when available */
 		prescaler = PWM_PRESCAL_MASK;
@@ -206,6 +236,7 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 	int ret;
 	unsigned int delay_us, prescaler;
 	unsigned long now;
+	bool bypass;
 
 	pwm_get_state(pwm, &cstate);
 
@@ -220,7 +251,8 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 	spin_lock(&sun4i_pwm->ctrl_lock);
 	ctrl = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
-	ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler);
+	ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler,
+				  &bypass);
 	if (ret) {
 		dev_err(chip->dev, "period exceeds the maximum value\n");
 		spin_unlock(&sun4i_pwm->ctrl_lock);
@@ -229,6 +261,18 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 		return ret;
 	}
 
+	if (sun4i_pwm->data->has_direct_mod_clk_output) {

drivers/pwm/pwm-sun4i.c static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 274

Quoted 10 lines
drivers/pwm/pwm-sun4i.c +10 -0
+		if (bypass) {
+			ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
+			/* We can skip other parameter */
+			sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
+			spin_unlock(&sun4i_pwm->ctrl_lock);
+			return 0;
+		} else {
+			ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
+		}
+	}

This could be simplified to:

	if (bypass) {
		ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
		/*
		 * Other parameters are not relevant in this mode and so
		 * writing them can be skipped
		 */
		sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
		spin_unlock(&sun4i_pwm->ctrl_lock);
		return 0;
	} else {
		ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
	}

which has the advantage(?) that the bypass bit is also (more obviously) cleared for SoCs that don't support it and it reduces the indention level.

Best regards
Uwe

Signature · 7 lines
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20191121211630.slgayfbuykwvlvdt%40pengutronix.de.
#10 lore raw

Re: [PATCH v8 5/6] pwm: sun4i: Add support to output source clock directly

Hi Uwe,

Quoted 139 lines · Uwe Kleine-König
Quoted 111 lines · Clément Péron

From: Jernej Skrabec <[email protected]>

PWM core has an option to bypass whole logic and output unchanged source clock as PWM output. This is achieved by enabling bypass bit.

Note that when bypass is enabled, no other setting has any meaning, not even enable bit.

This mode of operation is needed to achieve high enough frequency to serve as clock source for AC200 chip which is integrated into same package as H6 SoC.

---
 drivers/pwm/pwm-sun4i.c | 48 +++++++++++++++++++++++++++++++++++++++--
 1 file changed, 46 insertions(+), 2 deletions(-)
drivers/pwm/pwm-sun4i.c +35 -2
index 1fa2057419fb..0fe9c680d6d0 100644
@@ -3,6 +3,10 @@
  * Driver for Allwinner sun4i Pulse Width Modulation Controller
  *
  * Copyright (C) 2014 Alexandre Belloni <[email protected]>
+ *
+ * Limitations:
+ * - When outputing the source clock directly, the PWM logic will be bypassed
+ *   and the currently running period is not guaranteed to be completed
  */
 
 #include <linux/bitops.h>
@@ -73,6 +77,7 @@ static const u32 prescaler_table[] = {
 
 struct sun4i_pwm_data {
      bool has_prescaler_bypass;
+     bool has_direct_mod_clk_output;
      unsigned int npwm;
 };
 
@@ -118,6 +123,20 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
      val = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
+     /*
+      * PWM chapter in H6 manual has a diagram which explains that if bypass
+      * bit is set, no other setting has any meaning. Even more, experiment
+      * proved that also enable bit is ignored in this case.
+      */
+     if ((val & BIT_CH(PWM_BYPASS, pwm->hwpwm)) &&
+         sun4i_pwm->data->has_direct_mod_clk_output) {
+             state->period = DIV_ROUND_UP_ULL(NSEC_PER_SEC, clk_rate);
+             state->duty_cycle = DIV_ROUND_UP_ULL(state->period, 2);
+             state->polarity = PWM_POLARITY_NORMAL;
+             state->enabled = true;
+             return;
+     }
+
      if ((PWM_REG_PRESCAL(val, pwm->hwpwm) == PWM_PRESCAL_MASK) &&
          sun4i_pwm->data->has_prescaler_bypass)
              prescaler = 1;
@@ -149,13 +168,24 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
 static int sun4i_pwm_calculate(struct sun4i_pwm_chip *sun4i_pwm,
                             const struct pwm_state *state,
-                            u32 *dty, u32 *prd, unsigned int *prsclr)
+                            u32 *dty, u32 *prd, unsigned int *prsclr,
+                            bool *bypass)
 {
      u64 clk_rate, div = 0;
      unsigned int pval, prescaler = 0;
 
      clk_rate = clk_get_rate(sun4i_pwm->clk);
 
+     *bypass = sun4i_pwm->data->has_direct_mod_clk_output &&
+               state->enabled &&
+               (state->period * clk_rate >= NSEC_PER_SEC) &&
+               (state->period * clk_rate < 2 * NSEC_PER_SEC) &&
+               (state->duty_cycle * clk_rate * 2 >= NSEC_PER_SEC);
+
+     /* Skip calculation of other parameters if we bypass them */
+     if (*bypass)
+             return 0;
+
      if (sun4i_pwm->data->has_prescaler_bypass) {
              /* First, test without any prescaler when available */
              prescaler = PWM_PRESCAL_MASK;
@@ -206,6 +236,7 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
      int ret;
      unsigned int delay_us, prescaler;
      unsigned long now;
+     bool bypass;
 
      pwm_get_state(pwm, &cstate);
 
@@ -220,7 +251,8 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
      spin_lock(&sun4i_pwm->ctrl_lock);
      ctrl = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
-     ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler);
+     ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler,
+                               &bypass);
      if (ret) {
              dev_err(chip->dev, "period exceeds the maximum value\n");
              spin_unlock(&sun4i_pwm->ctrl_lock);
@@ -229,6 +261,18 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
              return ret;
      }
 
+     if (sun4i_pwm->data->has_direct_mod_clk_output) {

drivers/pwm/pwm-sun4i.c static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 274

Quoted 10 lines
drivers/pwm/pwm-sun4i.c +10 -0
+             if (bypass) {
+                     ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
+                     /* We can skip other parameter */
+                     sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
+                     spin_unlock(&sun4i_pwm->ctrl_lock);
+                     return 0;
+             } else {
+                     ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
+             }
+     }

This could be simplified to:

        if (bypass) {
                ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
                /*
                 * Other parameters are not relevant in this mode and so
                 * writing them can be skipped
                 */
                sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
                spin_unlock(&sun4i_pwm->ctrl_lock);
                return 0;
        } else {
                ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
        }
Quoted 3 lines

which has the advantage(?) that the bypass bit is also (more obviously) cleared for SoCs that don't support it and it reduces the indention level.

This bit is not guaranteed to be reserved for all the SoC variants.

I don't think it's a good idea to set to 0 a bit which is undefined.

Regards,
Clement

Quoted 7 lines

Best regards
Uwe

--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | https://www.pengutronix.de/ |

Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCcdhH9zbRMMYsZbBYL-H8YWn2kimvJEjZ8Z8kF7Uh9MCpg%40mail.gmail.com.
#11 lore raw

Re: [PATCH v8 5/6] pwm: sun4i: Add support to output source clock directly

Hi Uwe,

Quoted 144 lines · Clément Péron

Hi Uwe,

Quoted 139 lines · Uwe Kleine-König
Quoted 111 lines · Clément Péron

From: Jernej Skrabec <[email protected]>

PWM core has an option to bypass whole logic and output unchanged source clock as PWM output. This is achieved by enabling bypass bit.

Note that when bypass is enabled, no other setting has any meaning, not even enable bit.

This mode of operation is needed to achieve high enough frequency to serve as clock source for AC200 chip which is integrated into same package as H6 SoC.

---
 drivers/pwm/pwm-sun4i.c | 48 +++++++++++++++++++++++++++++++++++++++--
 1 file changed, 46 insertions(+), 2 deletions(-)
drivers/pwm/pwm-sun4i.c +35 -2
index 1fa2057419fb..0fe9c680d6d0 100644
@@ -3,6 +3,10 @@
  * Driver for Allwinner sun4i Pulse Width Modulation Controller
  *
  * Copyright (C) 2014 Alexandre Belloni <[email protected]>
+ *
+ * Limitations:
+ * - When outputing the source clock directly, the PWM logic will be bypassed
+ *   and the currently running period is not guaranteed to be completed
  */
 
 #include <linux/bitops.h>
@@ -73,6 +77,7 @@ static const u32 prescaler_table[] = {
 
 struct sun4i_pwm_data {
      bool has_prescaler_bypass;
+     bool has_direct_mod_clk_output;
      unsigned int npwm;
 };
 
@@ -118,6 +123,20 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
      val = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
+     /*
+      * PWM chapter in H6 manual has a diagram which explains that if bypass
+      * bit is set, no other setting has any meaning. Even more, experiment
+      * proved that also enable bit is ignored in this case.
+      */
+     if ((val & BIT_CH(PWM_BYPASS, pwm->hwpwm)) &&
+         sun4i_pwm->data->has_direct_mod_clk_output) {
+             state->period = DIV_ROUND_UP_ULL(NSEC_PER_SEC, clk_rate);
+             state->duty_cycle = DIV_ROUND_UP_ULL(state->period, 2);
+             state->polarity = PWM_POLARITY_NORMAL;
+             state->enabled = true;
+             return;
+     }
+
      if ((PWM_REG_PRESCAL(val, pwm->hwpwm) == PWM_PRESCAL_MASK) &&
          sun4i_pwm->data->has_prescaler_bypass)
              prescaler = 1;
@@ -149,13 +168,24 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
 static int sun4i_pwm_calculate(struct sun4i_pwm_chip *sun4i_pwm,
                             const struct pwm_state *state,
-                            u32 *dty, u32 *prd, unsigned int *prsclr)
+                            u32 *dty, u32 *prd, unsigned int *prsclr,
+                            bool *bypass)
 {
      u64 clk_rate, div = 0;
      unsigned int pval, prescaler = 0;
 
      clk_rate = clk_get_rate(sun4i_pwm->clk);
 
+     *bypass = sun4i_pwm->data->has_direct_mod_clk_output &&
+               state->enabled &&
+               (state->period * clk_rate >= NSEC_PER_SEC) &&
+               (state->period * clk_rate < 2 * NSEC_PER_SEC) &&
+               (state->duty_cycle * clk_rate * 2 >= NSEC_PER_SEC);
+
+     /* Skip calculation of other parameters if we bypass them */
+     if (*bypass)
+             return 0;
+
      if (sun4i_pwm->data->has_prescaler_bypass) {
              /* First, test without any prescaler when available */
              prescaler = PWM_PRESCAL_MASK;
@@ -206,6 +236,7 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
      int ret;
      unsigned int delay_us, prescaler;
      unsigned long now;
+     bool bypass;
 
      pwm_get_state(pwm, &cstate);
 
@@ -220,7 +251,8 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
      spin_lock(&sun4i_pwm->ctrl_lock);
      ctrl = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
-     ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler);
+     ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler,
+                               &bypass);
      if (ret) {
              dev_err(chip->dev, "period exceeds the maximum value\n");
              spin_unlock(&sun4i_pwm->ctrl_lock);
@@ -229,6 +261,18 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
              return ret;
      }
 
+     if (sun4i_pwm->data->has_direct_mod_clk_output) {

drivers/pwm/pwm-sun4i.c static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 274

Quoted 10 lines
drivers/pwm/pwm-sun4i.c +10 -0
+             if (bypass) {
+                     ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
+                     /* We can skip other parameter */
+                     sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
+                     spin_unlock(&sun4i_pwm->ctrl_lock);
+                     return 0;
+             } else {
+                     ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
+             }
+     }

This could be simplified to:

        if (bypass) {
                ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
                /*
                 * Other parameters are not relevant in this mode and so
                 * writing them can be skipped
                 */
                sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
                spin_unlock(&sun4i_pwm->ctrl_lock);
                return 0;
        } else {
                ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
        }
Quoted 7 lines
Quoted 3 lines

which has the advantage(?) that the bypass bit is also (more obviously) cleared for SoCs that don't support it and it reduces the indention level.

This bit is not guaranteed to be reserved for all the SoC variants.

I don't think it's a good idea to set to 0 a bit which is undefined.

Let me know if you agree or not with this and I send the v9 according to your answer.

Regards,
Clément

Quoted 11 lines

Regards,
Clement

Quoted 7 lines

Best regards
Uwe

--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | https://www.pengutronix.de/ |

Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCcd8VK2xHqRuWTVpNvw4e%2BrCR9-KjOSF5KsTcN9qQhaNVw%40mail.gmail.com.
#12 lore raw

Re: [PATCH v8 5/6] pwm: sun4i: Add support to output source clock directly

Quoted 151 lines · Clément Péron

Hi Uwe,

Quoted 148 lines · Clément Péron

Hi Uwe,

Quoted 142 lines · Uwe Kleine-König
Quoted 111 lines · Clément Péron

From: Jernej Skrabec <[email protected]>

PWM core has an option to bypass whole logic and output unchanged source clock as PWM output. This is achieved by enabling bypass bit.

Note that when bypass is enabled, no other setting has any meaning, not even enable bit.

This mode of operation is needed to achieve high enough frequency to serve as clock source for AC200 chip which is integrated into same package as H6 SoC.

---
 drivers/pwm/pwm-sun4i.c | 48 +++++++++++++++++++++++++++++++++++++++--
 1 file changed, 46 insertions(+), 2 deletions(-)
drivers/pwm/pwm-sun4i.c +35 -2
index 1fa2057419fb..0fe9c680d6d0 100644
@@ -3,6 +3,10 @@
  * Driver for Allwinner sun4i Pulse Width Modulation Controller
  *
  * Copyright (C) 2014 Alexandre Belloni <[email protected]>
+ *
+ * Limitations:
+ * - When outputing the source clock directly, the PWM logic will be bypassed
+ *   and the currently running period is not guaranteed to be completed
  */
 
 #include <linux/bitops.h>
@@ -73,6 +77,7 @@ static const u32 prescaler_table[] = {
 
 struct sun4i_pwm_data {
      bool has_prescaler_bypass;
+     bool has_direct_mod_clk_output;
      unsigned int npwm;
 };
 
@@ -118,6 +123,20 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
      val = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
+     /*
+      * PWM chapter in H6 manual has a diagram which explains that if bypass
+      * bit is set, no other setting has any meaning. Even more, experiment
+      * proved that also enable bit is ignored in this case.
+      */
+     if ((val & BIT_CH(PWM_BYPASS, pwm->hwpwm)) &&
+         sun4i_pwm->data->has_direct_mod_clk_output) {
+             state->period = DIV_ROUND_UP_ULL(NSEC_PER_SEC, clk_rate);
+             state->duty_cycle = DIV_ROUND_UP_ULL(state->period, 2);
+             state->polarity = PWM_POLARITY_NORMAL;
+             state->enabled = true;
+             return;
+     }
+
      if ((PWM_REG_PRESCAL(val, pwm->hwpwm) == PWM_PRESCAL_MASK) &&
          sun4i_pwm->data->has_prescaler_bypass)
              prescaler = 1;
@@ -149,13 +168,24 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
 static int sun4i_pwm_calculate(struct sun4i_pwm_chip *sun4i_pwm,
                             const struct pwm_state *state,
-                            u32 *dty, u32 *prd, unsigned int *prsclr)
+                            u32 *dty, u32 *prd, unsigned int *prsclr,
+                            bool *bypass)
 {
      u64 clk_rate, div = 0;
      unsigned int pval, prescaler = 0;
 
      clk_rate = clk_get_rate(sun4i_pwm->clk);
 
+     *bypass = sun4i_pwm->data->has_direct_mod_clk_output &&
+               state->enabled &&
+               (state->period * clk_rate >= NSEC_PER_SEC) &&
+               (state->period * clk_rate < 2 * NSEC_PER_SEC) &&
+               (state->duty_cycle * clk_rate * 2 >= NSEC_PER_SEC);
+
+     /* Skip calculation of other parameters if we bypass them */
+     if (*bypass)
+             return 0;
+
      if (sun4i_pwm->data->has_prescaler_bypass) {
              /* First, test without any prescaler when available */
              prescaler = PWM_PRESCAL_MASK;
@@ -206,6 +236,7 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
      int ret;
      unsigned int delay_us, prescaler;
      unsigned long now;
+     bool bypass;
 
      pwm_get_state(pwm, &cstate);
 
@@ -220,7 +251,8 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
      spin_lock(&sun4i_pwm->ctrl_lock);
      ctrl = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
-     ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler);
+     ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler,
+                               &bypass);
      if (ret) {
              dev_err(chip->dev, "period exceeds the maximum value\n");
              spin_unlock(&sun4i_pwm->ctrl_lock);
@@ -229,6 +261,18 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
              return ret;
      }
 
+     if (sun4i_pwm->data->has_direct_mod_clk_output) {

drivers/pwm/pwm-sun4i.c static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 274

Quoted 10 lines
drivers/pwm/pwm-sun4i.c +10 -0
+             if (bypass) {
+                     ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
+                     /* We can skip other parameter */
+                     sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
+                     spin_unlock(&sun4i_pwm->ctrl_lock);
+                     return 0;
+             } else {
+                     ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
+             }
+     }

This could be simplified to:

        if (bypass) {
                ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
                /*
                 * Other parameters are not relevant in this mode and so
                 * writing them can be skipped
                 */
                sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
                spin_unlock(&sun4i_pwm->ctrl_lock);
                return 0;
        } else {
                ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
        }

which has the advantage(?) that the bypass bit is also (more obviously) cleared for SoCs that don't support it and it reduces the indention level.

Quoted 6 lines
Quoted 3 lines

This bit is not guaranteed to be reserved for all the SoC variants.

I don't think it's a good idea to set to 0 a bit which is undefined.

Let me know if you agree or not with this and I send the v9 according to your answer.

If my suggestion is not safe according to the documentation, it is obviously wrong. So only take it into account if a zero can be safely written.

Best regards
Uwe

Signature · 7 lines
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20191123200058.kz2farbyvruybtjj%40pengutronix.de.
#13 lore raw

PATCH v8 6/6 pwm: sun4i: Add support for H6 PWM

In reply to Clément Péron

From: Jernej Skrabec <[email protected]>

Now that sun4i PWM driver supports deasserting reset line and enabling bus clock, support for H6 PWM can be added.

Note that while H6 PWM has two channels, only first one is wired to output pin. Second channel is used as a clock source to companion AC200 chip which is bundled into same package.

---
 drivers/pwm/pwm-sun4i.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/pwm/pwm-sun4i.c +9 -0
index 0fe9c680d6d0..84f3ccab47f9 100644
@@ -360,6 +360,12 @@ static const struct sun4i_pwm_data sun4i_pwm_single_bypass = {
 	.npwm = 1,
 };
 
+static const struct sun4i_pwm_data sun50i_h6_pwm_data = {
+	.has_prescaler_bypass = true,
+	.has_direct_mod_clk_output = true,
+	.npwm = 2,
+};
+
 static const struct of_device_id sun4i_pwm_dt_ids[] = {
 	{
 		.compatible = "allwinner,sun4i-a10-pwm",
@@ -376,6 +382,9 @@ static const struct of_device_id sun4i_pwm_dt_ids[] = {
 	}, {
 		.compatible = "allwinner,sun8i-h3-pwm",
 		.data = &sun4i_pwm_single_bypass,
+	}, {
+		.compatible = "allwinner,sun50i-h6-pwm",
+		.data = &sun50i_h6_pwm_data,
 	}, {
 		/* sentinel */
 	},
Signature · 6 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20191121195902.6906-7-peron.clem%40gmail.com.