PCI: layerscape: Add Support for ls2085a and ls2080a EP mode
PATCH 1/3 PCI: layerscape: Add Support for ls2085a and ls2080a EP mode
Due to the ls2085a and ls2080a use difference way to set the BAR size, so add the BAR size init code here.
depends on: http://patchwork.ozlabs.org/project/uboot/list/?series=108172&state=*
--- drivers/pci/pcie_layerscape.c | 19 +++++++++++++------ 1 file changed, 13 insertions(+), 6 deletions(-)
drivers/pci/pcie_layerscape.c +13 -6
@@ -467,18 +467,25 @@ static void ls_pcie_setup_ep(struct ls_pcie *pcie)*/ writel (0 , pcie->dbi +PCIE_MISC_CONTROL_1_OFF ); + bar_base = pcie->dbi + +PCIE_MASK_OFFSET (pcie->cfg2_flag, pf); +if (pcie->cfg2_flag) { -for (vf =0 ; vf <=PCIE_VF_NUM ; vf++) { +ctrl_writel (pcie, +PCIE_LCTRL0_VAL (pf,0 ), +PCIE_PF_VF_CTRL ); +ls_pcie_ep_setup_bars (bar_base); + +for (vf =1 ; vf <=PCIE_VF_NUM ; vf++) {ctrl_writel (pcie,PCIE_LCTRL0_VAL (pf, vf),PCIE_PF_VF_CTRL ); +ls_pcie_ep_setup_vf_bars (bar_base); } + }else { +ls_pcie_ep_setup_bars (bar_base); +ls_pcie_ep_setup_vf_bars (bar_base); } - bar_base = pcie->dbi + -PCIE_MASK_OFFSET (pcie->cfg2_flag, pf); -ls_pcie_ep_setup_bars (bar_base); -ls_pcie_ep_setup_vf_bars (bar_base); -ls_pcie_ep_setup_atu (pcie, pf); }
Signature · 1 line
2.9.5
PATCH 2/3 PCI: layerscape: Add the configuration for PF1 and VFs
Add the INBOUND configuration for PF1 and VFs of PF1 and PF0, Modify the outbound configuration for PF0 and PF1.
--- drivers/pci/pcie_layerscape.c | 95 +++++++++++++++++++++++++++---------------- drivers/pci/pcie_layerscape.h | 9 ++-- 2 files changed, 65 insertions(+), 39 deletions(-)
drivers/pci/pcie_layerscape.c +59 -36
@@ -93,7 +93,7 @@ static void ls_pcie_cfg1_set_busdev(struct ls_pcie *pcie, u32 busdev) }static void ls_pcie_atu_outbound_set (struct ls_pcie *pcie,int idx,int type, -u64 phys,u64 bus_addr,pci_size_t size) +u64 phys,u64 bus_addr,u64 size) {dbi_writel (pcie,PCIE_ATU_REGION_OUTBOUND | idx,PCIE_ATU_VIEWPORT );dbi_writel (pcie, (u32 )phys,PCIE_ATU_LOWER_BASE );
@@ -106,30 +106,27 @@ static void ls_pcie_atu_outbound_set(struct ls_pcie *pcie, int idx, int type, }/* Use bar match mode and MEM type as default */ -static void ls_pcie_atu_inbound_set (struct ls_pcie *pcie,int idx, -int bar,u64 phys,u32 pf) +static void ls_pcie_atu_inbound_set (struct ls_pcie *pcie,u32 pf,u32 vf_flag, +int idx,int bar,u64 phys) { -u32 cr1 =0 ; - -if (pf) - cr1 |=PCIE_CTRL1_FUNC_NUM ; -dbi_writel (pcie,PCIE_ATU_REGION_INBOUND | idx,PCIE_ATU_VIEWPORT );dbi_writel (pcie, (u32 )phys,PCIE_ATU_LOWER_TARGET );dbi_writel (pcie, phys >>32 ,PCIE_ATU_UPPER_TARGET ); -dbi_writel (pcie,PCIE_ATU_TYPE_MEM | cr1,PCIE_ATU_CR1 ); +dbi_writel (pcie,PCIE_ATU_TYPE_MEM |PCIE_ATU_FUNC_NUM (pf), +PCIE_ATU_CR1 );dbi_writel (pcie,PCIE_ATU_ENABLE |PCIE_ATU_BAR_MODE_ENABLE | + (pcie->sriov_flag ?PCIE_ATU_FUNC_NUM_MATCH_EN :0 ) | + (vf_flag ?PCIE_ATU_VFBAR_MATCH_MODE_EN :0 ) |PCIE_ATU_BAR_NUM (bar),PCIE_ATU_CR2 ); } -static void ls_pcie_dump_atu (struct ls_pcie *pcie) +static void ls_pcie_dump_atu (struct ls_pcie *pcie,u32 win_num,u32 type) { -int i; +int win_idx; -for (i =0 ; i <PCIE_ATU_REGION_NUM ; i++) { -dbi_writel (pcie,PCIE_ATU_REGION_OUTBOUND | i, -PCIE_ATU_VIEWPORT ); -debug ("iATU%d:\n" , i); +for (win_idx =0 ; win_idx < win_num; win_idx++) { +dbi_writel (pcie, type | win_idx,PCIE_ATU_VIEWPORT ); +debug ("iATU%d:\n" , win_idx);debug ("\tLOWER PHYS 0x%08x\n" ,dbi_readl (pcie,PCIE_ATU_LOWER_BASE )); debug("\tUPPER PHYS 0x%08x\n",
@@ -225,7 +222,7 @@ static void ls_pcie_setup_atu(struct ls_pcie *pcie) pref->bus_start, pref->size); -ls_pcie_dump_atu (pcie); +ls_pcie_dump_atu (pcie,PCIE_ATU_REGION_NUM ,PCIE_ATU_REGION_OUTBOUND ); }/* Return 0 if the address is valid, -errno if not valid */
@@ -352,33 +349,52 @@ static void ls_pcie_setup_ctrl(struct ls_pcie *pcie)static void ls_pcie_ep_setup_atu (struct ls_pcie *pcie,u32 pf) { -pci_size_t atu_size =CONFIG_SYS_PCI_MEMORY_SIZE ;u64 phys =0 ; +u32 vf_flag =0 ; - phys =CONFIG_SYS_PCI_EP_MEMORY_BASE + pf *SZ_2M ; + phys =CONFIG_SYS_PCI_EP_MEMORY_BASE + pf *SZ_64M ; - phys =ALIGN (phys,PCIE_BAR0_SIZE );/* ATU 0 : INBOUND : map BAR0 */ -ls_pcie_atu_inbound_set (pcie,0 + pf *BAR_NUM ,0 , phys, pf); + phys =ALIGN (phys,PCIE_BAR0_SIZE ); +ls_pcie_atu_inbound_set (pcie, pf, vf_flag,0 + pf *BAR_NUM ,0 , phys);/* ATU 1 : INBOUND : map BAR1 */ phys =ALIGN (phys +PCIE_BAR0_SIZE ,PCIE_BAR1_SIZE ); -ls_pcie_atu_inbound_set (pcie,1 + pf *BAR_NUM ,1 , phys, pf); +ls_pcie_atu_inbound_set (pcie, pf, vf_flag,1 + pf *BAR_NUM ,1 , phys);/* ATU 2 : INBOUND : map BAR2 */ phys =ALIGN (phys +PCIE_BAR1_SIZE ,PCIE_BAR2_SIZE ); -ls_pcie_atu_inbound_set (pcie,2 + pf *BAR_NUM ,2 , phys, pf); -/* ATU 3 : INBOUND : map BAR2 */ - phys =ALIGN (phys +PCIE_BAR2_SIZE ,PCIE_BAR2_SIZE ); -ls_pcie_atu_inbound_set (pcie,3 + pf *BAR_NUM ,4 , phys, pf); - -/* ATU 0 : OUTBOUND : map MEM */ -ls_pcie_atu_outbound_set (pcie,PCIE_ATU_REGION_INDEX0 , -PCIE_ATU_TYPE_MEM , (u64 )pcie->cfg_res.start, -0 , atu_size); +ls_pcie_atu_inbound_set (pcie, pf, vf_flag,2 + pf *BAR_NUM ,2 , phys); +/* ATU 3 : INBOUND : map BAR4 */ + phys =ALIGN (phys +PCIE_BAR2_SIZE ,PCIE_BAR4_SIZE ); +ls_pcie_atu_inbound_set (pcie, pf, vf_flag,3 + pf *BAR_NUM ,4 , phys); + +if (pcie->sriov_flag) { + vf_flag =1 ; +/* ATU 4 : INBOUND : map BAR0 */ + phys =ALIGN (phys +PCIE_BAR4_SIZE ,PCIE_BAR0_SIZE ); +ls_pcie_atu_inbound_set (pcie, pf, vf_flag, +4 + pf *BAR_NUM ,0 , phys); +/* ATU 5 : INBOUND : map BAR1 */ + phys =ALIGN (phys +PCIE_BAR0_SIZE *PCIE_VF_NUM , +PCIE_BAR1_SIZE ); +ls_pcie_atu_inbound_set (pcie, pf, vf_flag, +5 + pf *BAR_NUM ,1 , phys); +/* ATU 6 : INBOUND : map BAR2 */ + phys =ALIGN (phys +PCIE_BAR1_SIZE *PCIE_VF_NUM , +PCIE_BAR2_SIZE ); +ls_pcie_atu_inbound_set (pcie, pf, vf_flag, +6 + pf *BAR_NUM ,2 , phys); +/* ATU 7 : INBOUND : map BAR4 */ + phys =ALIGN (phys +PCIE_BAR2_SIZE *PCIE_VF_NUM , +PCIE_BAR4_SIZE ); +ls_pcie_atu_inbound_set (pcie, pf, vf_flag, +7 + pf *BAR_NUM ,4 , phys); + } -/* ATU 1 : OUTBOUND : map MEM */ -ls_pcie_atu_outbound_set (pcie,PCIE_ATU_REGION_INDEX1 , -PCIE_ATU_TYPE_MEM , (u64 )pcie->cfg_res.start - + atu_size, atu_size, atu_size); +/* ATU: OUTBOUND : map MEM */ +ls_pcie_atu_outbound_set (pcie, pf,PCIE_ATU_TYPE_MEM , + (u64 )pcie->cfg_res.start + + pf *CONFIG_SYS_PCI_MEMORY_SIZE , +0 ,CONFIG_SYS_PCI_MEMORY_SIZE ); }/* BAR0 and BAR1 are 32bit BAR2 and BAR4 are 64bit */
@@ -491,9 +507,13 @@ static void ls_pcie_setup_ep(struct ls_pcie *pcie)if (pcie->cfg2_flag)/* Disable CFG2 */ ctrl_writel (pcie,0 ,PCIE_PF_VF_CTRL ); +ls_pcie_dump_atu (pcie,PCIE_ATU_REGION_NUM_SRIOV , +PCIE_ATU_REGION_INBOUND ); }else {ls_pcie_ep_setup_bars (pcie->dbi +PCIE_NO_SRIOV_BAR_BASE );ls_pcie_ep_setup_atu (pcie,0 ); +ls_pcie_dump_atu (pcie,PCIE_ATU_REGION_NUM , +PCIE_ATU_REGION_INBOUND ); }ls_pcie_ep_enable_cfg (pcie);
@@ -566,7 +586,6 @@ static int ls_pcie_probe(struct udevice *dev)* Fix the pcie memory map address and PF control registers address * for LS2088A series SoCs */ - pcie->cfg2_flag =1 ;if (svr ==SVR_LS2088A || svr ==SVR_LS2084A || svr ==SVR_LS2048A || svr ==SVR_LS2044A || svr ==SVR_LS2081A || svr ==SVR_LS2041A ) {
@@ -575,8 +594,12 @@ static int ls_pcie_probe(struct udevice *dev)LS2088A_PCIE_PHYS_SIZE * pcie->idx; pcie->cfg_res.end = pcie->cfg_res.start + cfg_size; pcie->ctrl = pcie->lut +0x40000 ; - pcie->cfg2_flag =0 ; } + +if (svr ==SVR_LS2080A || svr ==SVR_LS2085A ) + pcie->cfg2_flag =1 ; +else + pcie->cfg2_flag =0 ;#endif /* CONFIG_FSL_LAYERSCAPE */ pcie->cfg0 = map_physmem(pcie->cfg_res.start,
drivers/pci/pcie_layerscape.h +6 -3
@@ -20,7 +20,7 @@#endif #ifndef CONFIG_SYS_PCI_MEMORY_SIZE -#define CONFIG_SYS_PCI_MEMORY_SIZE (2 * 1024 * 1024 * 1024UL)/* 2G */ +#define CONFIG_SYS_PCI_MEMORY_SIZE SZ_4G#endif #ifndef CONFIG_SYS_PCI_EP_MEMORY_BASE
@@ -40,14 +40,18 @@#define PCIE_ATU_REGION_INDEX2 (0x2 << 0)#define PCIE_ATU_REGION_INDEX3 (0x3 << 0)#define PCIE_ATU_REGION_NUM 6 +#define PCIE_ATU_REGION_NUM_SRIOV 24#define PCIE_ATU_CR1 0x904#define PCIE_ATU_TYPE_MEM (0x0 << 0)#define PCIE_ATU_TYPE_IO (0x2 << 0)#define PCIE_ATU_TYPE_CFG0 (0x4 << 0)#define PCIE_ATU_TYPE_CFG1 (0x5 << 0) +#define PCIE_ATU_FUNC_NUM (pf) (pf << 20)#define PCIE_ATU_CR2 0x908#define PCIE_ATU_ENABLE (0x1 << 31)#define PCIE_ATU_BAR_MODE_ENABLE (0x1 << 30) +#define PCIE_ATU_FUNC_NUM_MATCH_EN (1 << 19) +#define PCIE_ATU_VFBAR_MATCH_MODE_EN (1 << 26)#define PCIE_ATU_BAR_NUM (bar) ((bar) << 8)#define PCIE_ATU_LOWER_BASE 0x90C#define PCIE_ATU_UPPER_BASE 0x910
@@ -86,7 +90,7 @@#define PCIE_PF_NUM 2#define PCIE_VF_NUM 64 -#define BAR_NUM 4 +#define BAR_NUM 8#define PCIE_BAR0_SIZE SZ_4K/* 4K */ #define PCIE_BAR1_SIZE SZ_8K/* 8K for MSIX */
@@ -95,7 +99,6 @@#define PCIE_SRIOV_VFBAR0 0x19C#define PCIE_MISC_CONTROL_1_OFF 0x8BC -#define PCIE_CTRL1_FUNC_NUM 0x00100000#define PCIE_MASK_OFFSET (flag, pf) ((flag) ? 0 : (0x1000 + 0x20000 * (pf)))
Signature · 1 line
2.9.5
PATCH 3/3 PCI: layerscape: Add the PCIe EP mode support for lx2160a-v2
In reply to Xiaowei BaoAdd the PCIe EP mode support for lx2160a-v2 platform.
--- drivers/pci/pcie_layerscape.c | 8 +++++++- drivers/pci/pcie_layerscape.h | 9 ++++++++- 2 files changed, 15 insertions(+), 2 deletions(-)
drivers/pci/pcie_layerscape.c +7 -1
@@ -484,7 +484,8 @@ static void ls_pcie_setup_ep(struct ls_pcie *pcie)writel (0 , pcie->dbi +PCIE_MISC_CONTROL_1_OFF ); bar_base = pcie->dbi + -PCIE_MASK_OFFSET (pcie->cfg2_flag, pf); +PCIE_MASK_OFFSET (pcie->cfg2_flag, pf, + pcie->pf1_offset);if (pcie->cfg2_flag) { ctrl_writel(pcie,
@@ -596,6 +597,11 @@ static int ls_pcie_probe(struct udevice *dev) pcie->ctrl = pcie->lut +0x40000 ; } +if (svr ==SVR_LX2160A ) + pcie->pf1_offset =LX2160_PCIE_PF1_OFFSET ; +else + pcie->pf1_offset =LS_PCIE_PF1_OFFSET ; +if (svr ==SVR_LS2080A || svr ==SVR_LS2085A ) pcie->cfg2_flag =1 ;else
drivers/pci/pcie_layerscape.h +8 -1
@@ -100,7 +100,7 @@#define PCIE_SRIOV_VFBAR0 0x19C#define PCIE_MISC_CONTROL_1_OFF 0x8BC -#define PCIE_MASK_OFFSET (flag, pf) ((flag) ? 0 : (0x1000 + 0x20000 * (pf))) +#define PCIE_MASK_OFFSET (flag, pf, off) ((flag) ? 0 : (0x1000 + (off) * (pf)))/* LUT registers */ #define PCIE_LUT_UDR (n) (0x800 + (n) * 8)
@@ -132,6 +132,12 @@#define LS1021_PEXMSCPORTSR (pex_idx) (0x94 + (pex_idx) * 4)#define LS1021_LTSSM_STATE_SHIFT 20 +/* LX2160a PF1 offset */ +#define LX2160_PCIE_PF1_OFFSET 0x8000 + +/* layerscape PF1 offset */ +#define LS_PCIE_PF1_OFFSET 0x20000 +struct ls_pcie {int idx;struct list_head list;
@@ -150,6 +156,7 @@ struct ls_pcie {int next_lut_index;uint sriov_flag;uint cfg2_flag; +uint pf1_offset;int stream_id_cur;int mode; };
Signature · 1 line
2.9.5
PATCH 1/3 PCI: layerscape: Add Support for ls2085a and ls2080a EP mode
In reply to Xiaowei BaoQuoted 10 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Xiaowei Bao
Sent: Friday, November 22, 2019 1:04 PM
To:M.h. Lian <[email protected]>; Z.q. Hou <[email protected]>; Mingkai Hu <[email protected]>; Jagdish Gediya <[email protected]>; Pankaj Bansal <[email protected]>; u-boot at lists.denx.de
Cc: Xiaowei Bao <[email protected]>
Subject: [U-Boot] [PATCH 1/3] PCI: layerscape: Add Support for ls2085a and ls2080a EP mode
Quoted 5 lines
Due to the ls2085a and ls2080a use difference way to set the BAR size, so add the BAR size init code here.
Signed-off-by Xiaowei Bao <[email protected]> depends on:http://patchwork.ozlabs.org/project/uboot/list/?series=108172&state=*
<snip>
Depends-on patches are marked as "Changes Requested". Please help to provide latest version of those patches.
Priyanka
PATCH 1/3 PCI: layerscape: Add Support for ls2085a and ls2080a EP mode
Quoted 25 lines
-----Original Message-----
From: Priyanka Jain <[email protected]>
Sent: 2019年12月23日 18:43
To: Xiaowei Bao <[email protected]>;M.h. Lian <[email protected]>; Z.q. Hou <[email protected]>; Mingkai Hu <[email protected]>; Jagdish Gediya <[email protected]>; Pankaj Bansal <[email protected]>; u-boot at lists.denx.de
Cc: Xiaowei Bao <[email protected]>
Subject: RE: [U-Boot] [PATCH 1/3] PCI: layerscape: Add Support for ls2085a and ls2080a EP modeQuoted 4 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Xiaowei Bao
Sent: Friday, November 22, 2019 1:04 PM
To:M.h. Lian <[email protected]>; Z.q. HouQuoted 7 lines
Mingkai Hu <[email protected]>; Jagdish Gediya <[email protected]>; Pankaj Bansal <[email protected]>; u-boot at lists.denx.de
Cc: Xiaowei Bao <[email protected]>
Subject: [U-Boot] [PATCH 1/3] PCI: layerscape: Add Support for ls2085a and ls2080a EP mode
Quoted 8 lines
Quoted 5 lines
Due to the ls2085a and ls2080a use difference way to set the BAR size, so add the BAR size init code here.
Signed-off-by Xiaowei Bao <[email protected]> depends on:http://patchwork.ozlabs.org/project/uboot/list/?series=108172&state=*
<snip>
Depends-on patches are marked as "Changes Requested". Please help to provide latest version of those patches.
I have not start on this work, if spilt EP and RC driver in u-boot, maybe spend more time, I plan to do this in Feb, thanks.
Quoted 2 lines
Priyanka