Skip to contentSkip to conversation

net: phy: dp83867: fix speed 10 in sgmii mode

PATCH In review Adrian Bunk 2 participants 3 messages Nov 26, 2019 – Nov 27, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 net: phy: dp83867: fix speed 10 in sgmii mode

From: Max Uvarov <[email protected]>

Commit 333061b924539c0de081339643f45514f5f1c1e6 upstream.

For supporting 10Mps speed in SGMII mode DP83867_10M_SGMII_RATE_ADAPT bit of DP83867_10M_SGMII_CFG register has to be cleared by software. That does not affect speeds 100 and 1000 so can be done on init.

Cc Heiner Kallweit <[email protected]>
Cc Florian Fainelli <[email protected]>
Cc Andrew Lunn <[email protected]>
[ adapted for kernels without phy_modify_mmd ]

---
- already in 5.3
- applies and builds against 4.14 and 4.19
- tested with 4.14

---
 drivers/net/phy/dp83867.c | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
drivers/net/phy/dp83867.c +19 -0
index 12b09e6e03ba..81106314e6da 100644
@@ -37,6 +37,8 @@
 #define DP83867_STRAP_STS1	0x006E
 #define DP83867_RGMIIDCTL	0x0086
 #define DP83867_IO_MUX_CFG	0x0170
+#define DP83867_10M_SGMII_CFG   0x016F
+#define DP83867_10M_SGMII_RATE_ADAPT_MASK BIT(7)
 
 #define DP83867_SW_RESET	BIT(15)
 #define DP83867_SW_RESTART	BIT(14)
@@ -283,6 +285,23 @@ static int dp83867_config_init(struct phy_device *phydev)
 		}
 	}
 
+	if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
+		/* For support SPEED_10 in SGMII mode
+		 * DP83867_10M_SGMII_RATE_ADAPT bit
+		 * has to be cleared by software. That
+		 * does not affect SPEED_100 and
+		 * SPEED_1000.
+		 */
+		val = phy_read_mmd(phydev, DP83867_DEVADDR,
+				   DP83867_10M_SGMII_CFG);
+		val &= ~DP83867_10M_SGMII_RATE_ADAPT_MASK;
+		ret = phy_write_mmd(phydev, DP83867_DEVADDR,
+				    DP83867_10M_SGMII_CFG, val);
+
+		if (ret)
+			return ret;
+	}
+
 	/* Enable Interrupt output INT_OE in CFG3 register */
 	if (phy_interrupt_is_valid(phydev)) {
 		val = phy_read(phydev, DP83867_CFG3);
Signature · 1 line
2.20.1
#1 lore raw

PATCH 2/2 net: phy: dp83867: increase SGMII autoneg timer duration

From: Max Uvarov <[email protected]>

Commit 1a97a477e666cbdededab93bd3754e508f0c09d7 upstream.

After reset SGMII Autoneg timer is set to 2us (bits 6 and 5 are 01). That is not enough to finalize autonegatiation on some devices. Increase this timer duration to maximum supported 16ms.

Cc Heiner Kallweit <[email protected]>
Cc Florian Fainelli <[email protected]>
Cc Andrew Lunn <[email protected]>
[ adapted for kernels without phy_modify_mmd ]

---
- already in 5.3
- applies and builds against 4.14 and 4.19
- tested with 4.14

---
 drivers/net/phy/dp83867.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
drivers/net/phy/dp83867.c +18 -0
index 81106314e6da..e03e91d5f1b1 100644
@@ -33,6 +33,12 @@
 
 /* Extended Registers */
 #define DP83867_CFG4            0x0031
+#define DP83867_CFG4_SGMII_ANEG_MASK (BIT(5) | BIT(6))
+#define DP83867_CFG4_SGMII_ANEG_TIMER_11MS   (3 << 5)
+#define DP83867_CFG4_SGMII_ANEG_TIMER_800US  (2 << 5)
+#define DP83867_CFG4_SGMII_ANEG_TIMER_2US    (1 << 5)
+#define DP83867_CFG4_SGMII_ANEG_TIMER_16MS   (0 << 5)
+
 #define DP83867_RGMIICTL	0x0032
 #define DP83867_STRAP_STS1	0x006E
 #define DP83867_RGMIIDCTL	0x0086
@@ -300,6 +306,18 @@ static int dp83867_config_init(struct phy_device *phydev)
 
 		if (ret)
 			return ret;
+
+		/* After reset SGMII Autoneg timer is set to 2us (bits 6 and 5
+		 * are 01). That is not enough to finalize autoneg on some
+		 * devices. Increase this timer duration to maximum 16ms.
+		 */
+		val = phy_read_mmd(phydev, DP83867_DEVADDR, DP83867_CFG4);
+		val &= ~DP83867_CFG4_SGMII_ANEG_MASK;
+		val |= DP83867_CFG4_SGMII_ANEG_TIMER_16MS;
+		ret = phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_CFG4, val);
+
+		if (ret)
+			return ret;
 	}
 
 	/* Enable Interrupt output INT_OE in CFG3 register */
Signature · 1 line
2.20.1
maintainer
#2 lore raw
In reply to Adrian Bunk
Quoted 15 lines · Adrian Bunk

From: Max Uvarov <[email protected]>

Commit 333061b924539c0de081339643f45514f5f1c1e6 upstream.

For supporting 10Mps speed in SGMII mode DP83867_10M_SGMII_RATE_ADAPT bit of DP83867_10M_SGMII_CFG register has to be cleared by software. That does not affect speeds 100 and 1000 so can be done on init.

Cc Heiner Kallweit <[email protected]>
Cc Florian Fainelli <[email protected]>
Cc Andrew Lunn <[email protected]>
[ adapted for kernels without phy_modify_mmd ]
Quoted 4 lines

---
- already in 5.3
- applies and builds against 4.14 and 4.19
- tested with 4.14

Looks like Greg took these in, thanks!

Signature · 2 lines
Thanks,
Sasha