ARM: imx6: DHCOM i.MX6 PDK: Fixing reset
cover ARM: imx6: DHCOM i.MX6 PDK: Fixing reset
Hi,
currently the reset on the DHCOM i.MX6 board is brocken in u-boot.
This patchset fixes that by integrating the sysreset and watchdog dm driver.
regards,
Claudius
Claudius Heine (4):
ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
ARM: imx6: DHCOM i.MX6 PDK: Enable sysreset driver
ARM: imx6: DHCOM i.MX6 PDK: Enable wdt command
ARM: imx6: DHCOM i.MX6 PDK: Use HW_WATCHDOG in SPL
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi | 5 +++++ configs/dh_imx6_defconfig | 3 +++ include/configs/dh_imx6.h | 5 +++++ 3 files changed, 13 insertions(+)
Signature · 1 line
2.21.0
PATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
--- arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +5 -0
@@ -30,6 +30,11 @@ mux-int-port = <1>; mux-ext-port = <3>; }; + + wdt-reboot { + compatible = "wdt-reboot"; + wdt = <&wdog1>; + }; }; &audmux {
Signature · 1 line
2.21.0
PATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
Quoted 11 lines · Claudius Heine
Signed-off-by Claudius Heine <[email protected]>--- arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +0
-0@@ -30,6 +30,11 @@ mux-int-port = <1>;
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi line 40
Quoted 10 lines
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +5
-0mux-ext-port = <3>; }; + + wdt-reboot { + compatible = "wdt-reboot"; + wdt = <&wdog1>; + }; }; &audmux {
This should go into separate -u-boot.dtsi , so the base DT can be easily synced with Linux one.
PATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
Quoted 21 lines · Marek Vasut
Quoted 20 lines · Claudius Heine
Signed-off-by Claudius Heine <[email protected]>--- arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +5
-0@@ -30,6 +30,11 @@ mux-int-port = <1>; mux-ext-port = <3>; }; + + wdt-reboot { + compatible = "wdt-reboot"; + wdt = <&wdog1>; + }; };
Quoted 5 lines
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi line 40
Quoted 1 line
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +0
-0&audmux {This should go into separate
-u-boot.dtsi, so the base DT can be easily synced with Linux one.
Ok. Will do that in v2. Thanks!
Fabio Estevam
reviewerPATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
In reply to Claudius HeineHi Claudius,
Quoted 11 lines · Claudius Heine
Signed-off-by Claudius Heine <[email protected]>--- arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +0
-0
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi line 38
Quoted 9 lines
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +5
-0@@ -30,6 +30,11 @@ mux-int-port = <1>; mux-ext-port = <3>; }; + + wdt-reboot { + compatible = "wdt-reboot"; + wdt = <&wdog1>; + }; };
Could you use the the same way that Linux handles the imx2_wdt?
Please see the commit below:
commit ceea0c145d0c38badfcfc5443138e94ab094dc4a
Author: Robert Hancock <[email protected]> Date: Tue Aug 6 11:05:29 2019 -0600
watchdog: imx: Add DT ext-reset handling
The Linux imx2_wdt driver uses a fsl,ext-reset-output boolean in the device tree to specify whether the board design should use the external reset instead of the internal reset. Use this boolean to determine which mode to use rather than using external reset unconditionally.
For the legacy non-DM mode, the external reset is always used in order to maintain the previous behavior.
PATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
Hello Claudius, Fabio,
Quoted 33 lines · Fabio Estevam
Hi Claudius,
Quoted 10 lines · Claudius Heine
Signed-off-by Claudius Heine <[email protected]>--- arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +0
-0arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi line 38
Quoted 9 lines
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +5
-0@@ -30,6 +30,11 @@ mux-int-port = <1>; mux-ext-port = <3>; }; + + wdt-reboot { + compatible = "wdt-reboot"; + wdt = <&wdog1>; + }; };Could you use the the same way that Linux handles the
imx2_wdt?Please see the commit below:
commit
ceea0c145d0c38badfcfc5443138e94ab094dc4aAuthor: Robert Hancock <[email protected]> Date: Tue Aug 6 11:05:29 2019 -0600watchdog: imx: Add DT ext-reset handling
Quoted 7 lines
The Linux
imx2_wdtdriver uses a fsl,ext-reset-output boolean in the device tree to specify whether the board design should use the external reset instead of the internal reset. Use this boolean to determine which mode to use rather than using external reset unconditionally.For the legacy non-DM mode, the external reset is always used in order to maintain the previous behavior.
I think the source of the problem lies within this: The old behavior (before commit f2929d11a639 ("watchdog: imx: Use immediate reset bits for expire_now")) was asserting *both* external and internal reset. The datasheet mentions the following for the bit to enable external reset:
| There is no effect on [internal reset] upon writing on this bit. | [External reset] gets asserted along with [internal reset] if this bit | is set.
If the intention was to keep the old behavior, the imx_watchdog_expire_now() function needs to be changed to either
- (ext_reset == false) write WCR_WDE | WCR_WDA (ie. assert only internal), or
- (ext_reset == true) write WCR_WDE (ie. assert both internal and external).
Signature · 5 lines
Harald DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-62 Fax: +49-8142-66989-80 Email: hws at denx.de
PATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
In reply to Fabio EstevamHi Fabio,
Quoted 9 lines · Fabio Estevam
Hi Claudius,
Quoted 6 lines · Claudius Heine
Signed-off-by Claudius Heine <[email protected]>--- arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi | 5 +++++ 1 file changed, 5 insertions(+)
Quoted 16 lines
Quoted 5 lines
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +0
-0arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi line 38
Quoted 9 lines
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +5
-0@@ -30,6 +30,11 @@ mux-int-port = <1>; mux-ext-port = <3>; }; + + wdt-reboot { + compatible = "wdt-reboot"; + wdt = <&wdog1>; + }; };Could you use the the same way that Linux handles the
imx2_wdt?
That is the sysreset device node, not the imx2_wdt one. (I will move that into a '*-u-boot.dtsi' in v2)
Or am I misunderstanding you?
Fabio Estevam
reviewerPATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
Hi Claudius,
Quoted 4 lines · Claudius Heine
That is the sysreset device node, not the
imx2_wdtone. (I will move that into a '*-u-boot.dtsi' in v2)Or am I misunderstanding you?
What I am asking is: why do we need a specific sysreset node for U-Boot?
Can't we just add the wdog node the same way we do in the kernel (from the imx2_wdt binding) and get it to work?
Thanks
PATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
Quoted 10 lines · Fabio Estevam
Hi Claudius,
Quoted 4 lines · Claudius Heine
That is the sysreset device node, not the
imx2_wdtone. (I will move that into a '*-u-boot.dtsi' in v2)Or am I misunderstanding you?
What I am asking is: why do we need a specific sysreset node for U-Boot?
Good question. But I don't know a better answer to that than just saying that this is currently the way the reset is implemented in u-boot with DM AFAIK.
Quoted 2 lines
Can't we just add the wdog node the same way we do in the kernel (from the
imx2_wdtbinding) and get it to work?
Probably. But I currently don't know a way to do it that doesn't involve implementing new code.
I am currently more or less just doing what others have done before for similar boards (display5).
Fabio Estevam
reviewerPATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
Quoted 17 lines · Claudius Heine
Quoted 10 lines · Fabio Estevam
Hi Claudius,
Quoted 4 lines · Claudius Heine
That is the sysreset device node, not the
imx2_wdtone. (I will move that into a '*-u-boot.dtsi' in v2)Or am I misunderstanding you?
What I am asking is: why do we need a specific sysreset node for U-Boot?
Good question. But I don't know a better answer to that than just saying that this is currently the way the reset is implemented in u-boot with DM AFAIK.
Quoted 5 lines
Quoted 2 lines
Can't we just add the wdog node the same way we do in the kernel (from the
imx2_wdtbinding) and get it to work?Probably. But I currently don't know a way to do it that doesn't involve implementing new code.
Could you please try passing the wdog node the same we do in the kernel?
I prefer we have a single way to deal with watchdog instead of having a specific U-Boot method.
PATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
Quoted 21 lines · Fabio Estevam
Quoted 20 lines · Claudius Heine
Quoted 10 lines · Fabio Estevam
Hi Claudius,
Quoted 4 lines · Claudius Heine
That is the sysreset device node, not the
imx2_wdtone. (I will move that into a '*-u-boot.dtsi' in v2)Or am I misunderstanding you?
What I am asking is: why do we need a specific sysreset node for U-Boot?
Good question. But I don't know a better answer to that than just saying that this is currently the way the reset is implemented in u-boot with DM AFAIK.
Quoted 2 lines
Can't we just add the wdog node the same way we do in the kernel (from the
imx2_wdtbinding) and get it to work?
Quoted 7 lines
Quoted 2 lines
Probably. But I currently don't know a way to do it that doesn't involve implementing new code.
Could you please try passing the wdog node the same we do in the kernel?
I prefer we have a single way to deal with watchdog instead of having a specific U-Boot method.
Sorry, but we are probably misunderstanding each other here. So I try to go step by step to show how I think about this. Maybe that way we figure out where our understanding differs. Please bear with me, its a bit verbose :)
My patch adds the 'wdt-reboot' device node which is needed by u-boot to reset the device but doesn't exist in the linux kernel (since there is no 'wdt-reboot' driver):
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdog1>;
+ };
This 'wdt-reboot' node instruments its driver (drivers/sysreset/sysreset_watchdog.c [1]) to use the watchdog node (arch/arm/dts/imx6qdl.dtsi [2]) and its driver (drivers/watchdog/imx_watchdog.c [3]).
Neither the watchdog node in imx6qdl.dtsi [2], that is nearly identical to the one in the linux kernel [4], nor its driver [3] was touched by the changes in this patchset. The thing that has changed however is that 'CONFIG_SYSRESET_WATCHDOG' was enabled, which in turn enabled the 'CONFIG_WDT' switch. 'CONFIG_WDT' in turn disabled the 'hw_watchdog*' function definitions in the imx-watchdog driver and enabled 'CONFIG_WATCHDOG' and disabled 'CONFIG_HW_WATCHDOG'.
The 'CONFIG_WATCHDOG' and 'CONFIG_HW_WATCHDOG' changes cause the 'WATCHDOG_RESET*' defines in [5] to no longer refer to the 'hw_watchdog*' but instead to the 'watchdog*' functions. Those functions are handled by the watchdog DM class driver [6].
[1]
https://gitlab.denx.de/u-boot/u-boot/blob/4b19b89ca4a866b7baa642533e6dbd67cd832d27/drivers/sysreset/sysreset_watchdog.c#L48
[2]
https://gitlab.denx.de/u-boot/u-boot/blob/4b19b89ca4a866b7baa642533e6dbd67cd832d27/arch/arm/dts/imx6qdl.dtsi#L659
[3]
https://gitlab.denx.de/u-boot/u-boot/blob/4b19b89ca4a866b7baa642533e6dbd67cd832d27/drivers/watchdog/imx_watchdog.c
[4]
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/imx6qdl.dtsi?h=v5.4#n672
[5]
https://gitlab.denx.de/u-boot/u-boot/blob/4b19b89ca4a866b7baa642533e6dbd67cd832d27/include/watchdog.h#L38
[6]
https://gitlab.denx.de/u-boot/u-boot/blob/4b19b89ca4a866b7baa642533e6dbd67cd832d27/drivers/watchdog/wdt-uclass.c#L74
Fabio Estevam
reviewerPATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
Hi Claudius,
Quoted 4 lines · Claudius Heine
Sorry, but we are probably misunderstanding each other here. So I try to go step by step to show how I think about this. Maybe that way we figure out where our understanding differs. Please bear with me, its a bit verbose :)
What I don't understand is why do we need "wdt-reboot" for i.MX in U-Boot?
The i.MX watchdog driver is capable of resetting via internal watchdog or via a WDOG_B pin when the fsl,ext-reset-output property is passed.
Quoted 2 lines
My patch adds the 'wdt-reboot' device node which is needed by u-boot to reset the device but doesn't exist in the linux kernel (since there is
Right. This is the point I don't understand: why do we need a U-Boot wdt-reboot implementation in the first place?
The imx watchdog works in the kernel with DT. Why can't you just use the same binding in U-Boot?
Thanks
PATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
Quoted 14 lines · Fabio Estevam
Hi Claudius,
Quoted 4 lines · Claudius Heine
Sorry, but we are probably misunderstanding each other here. So I try to go step by step to show how I think about this. Maybe that way we figure out where our understanding differs. Please bear with me, its a bit verbose :)
What I don't understand is why do we need "wdt-reboot" for i.MX in U-Boot?
The i.MX watchdog driver is capable of resetting via internal watchdog or via a
WDOG_Bpin when the fsl,ext-reset-output property is passed.
Quoted 8 lines
Quoted 2 lines
My patch adds the 'wdt-reboot' device node which is needed by u-boot to reset the device but doesn't exist in the linux kernel (since there is
Right. This is the point I don't understand: why do we need a U-Boot wdt-reboot implementation in the first place?
The imx watchdog works in the kernel with DT. Why can't you just use the same binding in U-Boot?
I ended up needing to add this node for our board as well to be able to reset from U-Boot using DM. The watchdog itself is set up just from its own device tree entry, but there's nothing to tie the sysreset code into using the watchdog (and which one to use, since iMX has two of them) without that node being present.
In Linux this works differently - the watchdog drivers that are capable of triggering an immediate reset will register themselves as a reset handler automatically so the system will try to use that functionality in order to reboot the system. To avoid the need for that explicit wdt-reboot node, something like this would need to be implemented in U-Boot.
Quoted 3 lines
Thanks
Signature · 4 lines
Robert Hancock Senior Software Developer SED Systems, a division of Calian Ltd. Email: hancock at sedsystems.ca
Fabio Estevam
reviewerPATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
Hi Robert,
Quoted 11 lines · Robert Hancock
I ended up needing to add this node for our board as well to be able to reset from U-Boot using DM. The watchdog itself is set up just from its own device tree entry, but there's nothing to tie the sysreset code into using the watchdog (and which one to use, since iMX has two of them) without that node being present.
In Linux this works differently - the watchdog drivers that are capable of triggering an immediate reset will register themselves as a reset handler automatically so the system will try to use that functionality in order to reboot the system. To avoid the need for that explicit wdt-reboot node, something like this would need to be implemented in U-Boot.
Thanks for the clarification!
PATCH 1/4 ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
In reply to Fabio EstevamHi Fabio,
Quoted 9 lines · Fabio Estevam
Hi Claudius,
Quoted 4 lines · Claudius Heine
Sorry, but we are probably misunderstanding each other here. So I try to go step by step to show how I think about this. Maybe that way we figure out where our understanding differs. Please bear with me, its a bit verbose :)
Quoted 4 lines
What I don't understand is why do we need "wdt-reboot" for i.MX in U-Boot?
The i.MX watchdog driver is capable of resetting via internal watchdog or via a
WDOG_Bpin when the fsl,ext-reset-output property is passed.
Ok, right. Well my patches fixes the 'reset' command in u-boot and for that we need a sysreset driver in u-boot currently.
The watchdog itself works fine IIRC.
Quoted 12 lines
Quoted 3 lines
My patch adds the 'wdt-reboot' device node which is needed by u-boot to reset the device but doesn't exist in the linux kernel (since there is
Right. This is the point I don't understand: why do we need a U-Boot wdt-reboot implementation in the first place?
The imx watchdog works in the kernel with DT. Why can't you just use the same binding in U-Boot?
Thanks
PATCH 2/4 ARM: imx6: DHCOM i.MX6 PDK: Enable sysreset driver
In reply to Claudius Heine--- configs/dh_imx6_defconfig | 2 ++ 1 file changed, 2 insertions(+)
configs/dh_imx6_defconfig +2 -0
@@ -77,6 +77,8 @@ CONFIG_DM_SCSI=y CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_MXC_SPI=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_WATCHDOG=y CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_GADGET=y
Signature · 1 line
2.21.0
PATCH 3/4 ARM: imx6: DHCOM i.MX6 PDK: Enable wdt command
In reply to Claudius Heine--- configs/dh_imx6_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/dh_imx6_defconfig +1 -0
@@ -37,6 +37,7 @@ CONFIG_CMD_MMC=y CONFIG_CMD_SATA=y CONFIG_CMD_USB=y CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_WDT=y CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT4_WRITE=y
Signature · 1 line
2.21.0
PATCH 4/4 ARM: imx6: DHCOM i.MX6 PDK: Use HW_WATCHDOG in SPL
In reply to Claudius HeineThe SPL does not have DM enabled and therefor needs to use the hardware watchdog interface provided by the imx-watchdog driver.
--- include/configs/dh_imx6.h | 5 +++++ 1 file changed, 5 insertions(+)
include/configs/dh_imx6.h +5 -0
@@ -87,6 +87,11 @@#endif /* Watchdog */ +#if defined(CONFIG_SPL_BUILD ) +#undef CONFIG_WDT +#undef CONFIG_WATCHDOG +#define CONFIG_HW_WATCHDOG +#endif /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE
Signature · 1 line
2.21.0
cover ARM: imx6: DHCOM i.MX6 PDK: Fixing reset
In reply to Claudius HeineHello Claudius,
Quoted 5 lines · Claudius Heine
Hi,
currently the reset on the DHCOM i.MX6 board is brocken in u-boot.
This patchset fixes that by integrating the sysreset and watchdog dm driver.
I think you should clarify that reset was broken by commit f2929d11a639 ("watchdog: imx: Use immediate reset bits for expire_now") which changed reset to, by default, only assert the external reset [1]. DHCOM i.MX6 needs the internal reset though, which previously was asserted as as well. Maybe you can add a Fixes: line to one of your commits?
Additionally, I am still unsure whether the current default behavior is correct. I'd rather assert both external and internal reset, which is what the i.MX watchdog does on timeout as well (as long as WDT bit is set, which we do by default [2]). There is also an inconsistency between the non-DM implementation (external by default) and DM implementation (internal by default).
Quoted 9 lines
regards,
ClaudiusClaudius Heine (4):
ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
ARM: imx6: DHCOM i.MX6 PDK: Enable sysreset driver
ARM: imx6: DHCOM i.MX6 PDK: Enable wdt command
ARM: imx6: DHCOM i.MX6 PDK: UseHW_WATCHDOGin SPL
Quoted 5 lines
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi | 5 +++++ configs/dh_imx6_defconfig | 3 +++ include/configs/dh_imx6.h | 5 +++++ 3 files changed, 13 insertions(+)
[1]: https://gitlab.denx.de/u-boot/u-boot/blob/master/drivers/watchdog/imx_watchdog.c#L45
[2]: https://gitlab.denx.de/u-boot/u-boot/blob/master/drivers/watchdog/imx_watchdog.c#L96
Signature · 1 line
Harald
cover ARM: imx6: DHCOM i.MX6 PDK: Fixing reset
Hi Harald,
Quoted 7 lines · Harald Seiler
Hello Claudius,
Quoted 4 lines · Claudius Heine
Hi,
currently the reset on the DHCOM i.MX6 board is brocken in u-boot.
Quoted 7 lines
Quoted 1 line
This patchset fixes that by integrating the sysreset and watchdog dm driver.
I think you should clarify that reset was broken by commit
f2929d11a639("watchdog: imx: Use immediate reset bits forexpire_now") which changed reset to, by default, only assert the external reset [1]. DHCOM i.MX6 needs the internal reset though, which previously was asserted as as well. Maybe you can add aFixes:line to one of your commits?
Hmm... Not sure which of the commit should have the 'Fixes' line though, since each does some part of fixing it. Maybe I should squash them?
Quoted 7 lines
Additionally, I am still unsure whether the current default behavior is correct. I'd rather assert both external and internal reset, which is what the i.MX watchdog does on timeout as well (as long as WDT bit is set, which we do by default [2]). There is also an inconsistency between the non-DM implementation (external by default) and DM implementation (internal by default).
Yes, but that is a separate discussion IMO. This patch just addresses the stuff for DHCOM does not touch the imx-watchdog driver. Maybe an RFC patch that fixes the inconsistency might be useful to start it.
regards,
Claudius
cover ARM: imx6: DHCOM i.MX6 PDK: Fixing reset
In reply to Harald SeilerQuoted 7 lines · Harald Seiler
Hello Claudius,
Quoted 4 lines · Claudius Heine
Hi,
currently the reset on the DHCOM i.MX6 board is brocken in u-boot.
Quoted 7 lines
Quoted 1 line
This patchset fixes that by integrating the sysreset and watchdog dm driver.
I think you should clarify that reset was broken by commit
f2929d11a639("watchdog: imx: Use immediate reset bits forexpire_now") which changed reset to, by default, only assert the external reset [1]. DHCOM i.MX6 needs the internal reset though, which previously was asserted as as well. Maybe you can add aFixes:line to one of your commits?
The behavior of the driver in the DM mode should match what the Linux IMX watchdog driver is doing for both the watchdog timeout and reset operations. The reset operation there explicitly uses either internal reset or external reset, not both. For the actual watchdog timeout, they both set the WDT bit or not depending on whether ext-reset is set, which it seems would result in either internal+external reset or just internal reset (it doesn't look like you can trigger only an external reset on timeout).
Quoted 7 lines
Additionally, I am still unsure whether the current default behavior is correct. I'd rather assert both external and internal reset, which is what the i.MX watchdog does on timeout as well (as long as WDT bit is set, which we do by default [2]). There is also an inconsistency between the non-DM implementation (external by default) and DM implementation (internal by default).
The legacy non-DM implementation kept the settings for timeout the same as they were before. For the reset, it appears that it used to do internal+external reset whereas now it does external only, so it's possible that might cause an issue on some boards. However, they should really be switching to DM and setting the ext-reset attribute properly depending on which reset they actually want, as that's needed to get proper watchdog timeout/restart behavior in Linux as well. I doubt any board actually needs both internal and external resets since then Linux would be unable to reboot properly.
Quoted 19 lines
Quoted 10 lines
regards,
ClaudiusClaudius Heine (4):
ARM: dts: dh-imx6: add wdt-reboot node for sysreset driver
ARM: imx6: DHCOM i.MX6 PDK: Enable sysreset driver
ARM: imx6: DHCOM i.MX6 PDK: Enable wdt command
ARM: imx6: DHCOM i.MX6 PDK: UseHW_WATCHDOGin SPLQuoted 5 lines
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi | 5 +++++ configs/dh_imx6_defconfig | 3 +++ include/configs/dh_imx6.h | 5 +++++ 3 files changed, 13 insertions(+)[1]: https://gitlab.denx.de/u-boot/u-boot/blob/master/drivers/watchdog/imx_watchdog.c#L45
[2]: https://gitlab.denx.de/u-boot/u-boot/blob/master/drivers/watchdog/imx_watchdog.c#L96
Signature · 4 lines
Robert Hancock Senior Software Developer SED Systems, a division of Calian Ltd. Email: hancock at sedsystems.ca
cover ARM: imx6: DHCOM i.MX6 PDK: Fixing reset
Hi Robert,
Quoted 33 lines · Robert Hancock
Quoted 7 lines · Harald Seiler
Hello Claudius,
Quoted 4 lines · Claudius Heine
Hi,
currently the reset on the DHCOM i.MX6 board is brocken in u-boot.
Quoted 7 lines
Quoted 1 line
This patchset fixes that by integrating the sysreset and watchdog dm driver.
I think you should clarify that reset was broken by commit
f2929d11a639("watchdog: imx: Use immediate reset bits forexpire_now") which changed reset to, by default, only assert the external reset [1]. DHCOM i.MX6 needs the internal reset though, which previously was asserted as as well. Maybe you can add aFixes:line to one of your commits?The behavior of the driver in the DM mode should match what the Linux IMX watchdog driver is doing for both the watchdog timeout and reset operations. The reset operation there explicitly uses either internal reset or external reset, not both. For the actual watchdog timeout, they both set the WDT bit or not depending on whether ext-reset is set, which it seems would result in either internal+external reset or just internal reset (it doesn't look like you can trigger only an external reset on timeout).
Quoted 7 lines
Additionally, I am still unsure whether the current default behavior is correct. I'd rather assert both external and internal reset, which is what the i.MX watchdog does on timeout as well (as long as WDT bit is set, which we do by default [2]). There is also an inconsistency between the non-DM implementation (external by default) and DM implementation (internal by default).
Quoted 9 lines
The legacy non-DM implementation kept the settings for timeout the same as they were before. For the reset, it appears that it used to do internal+external reset whereas now it does external only, so it's possible that might cause an issue on some boards. However, they should really be switching to DM and setting the ext-reset attribute properly depending on which reset they actually want, as that's needed to get proper watchdog timeout/restart behavior in Linux as well. I doubt any board actually needs both internal and external resets since then Linux would be unable to reboot properly.
Thx, for the explanation! An issue I could think of is in the SPL, where DM is not possible because of size limitations. If that SPL wants to trigger a reset, will that not cause only an external reset and boards that need a internal one will just hang?
If that is the case, then there probably should be a way to configure that or let it trigger both like it did before.
regards,
Claudius
Signature · 6 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-54 Fax: (+49)-8142-66989-80 Email: ch at denx.de
PGP key: 6FF2 E59F 00C6 BC28 31D8 64C1 1173 CB19 9808 B153
Keyserver: hkp://pool.sks-keyservers.net