Skip to contentSkip to conversation

content: document speed, duplex

PATCH In review Michael S. Tsirkin 2 participants 2 messages Dec 3, 2019

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 content: document speed, duplex

Document as used by Linux.

---

changes from v2:
fix up units
actually there's no way for driver to know that link up
changed: it might have changed back.
make the device requirement a weaker "SHOULD" and instead ask that driver re-read on each config change notification

 content.tex | 39 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)
content.tex +39 -0
index d68cfaf..f7a6971 100644
@@ -2823,6 +2823,7 @@ \subsection{Feature bits}\label{sec:Device Types / Network Device / Feature bits
 
 \item[VIRTIO_NET_F_STANDBY(62)] Device may act as a standby for a primary
     device with the same MAC address.
+\item[VIRTIO_NET_F_SPEED_DUPLEX(63)] Device reports speed and duplex.
 \end{description}
 
 \subsubsection{Feature bit requirements}\label{sec:Device Types / Network Device / Feature bits / Feature bit requirements}
@@ -2882,12 +2883,28 @@ \subsection{Device configuration layout}\label{sec:Device Types / Network Device
 VIRTIO_NET_F_MTU is set. This field specifies the maximum MTU for the driver to
 use.
 
+The following two fields, \field{speed} and \field{duplex}, only
+exist if VIRTIO_NET_F_SPEED_DUPLEX is set.
+
+\field{speed} contains the device speed, in units of 1 MBit per
+second, 0 to 0x7ffffffff, or 0xfffffffff for unknown speed.
+
+\field{duplex} has the values of 0x00 for full duplex, 0x01 for
+half duplex and 0xff for unknown duplex state.
+
+Both \field{speed} and \field{duplex} can change, thus the driver
+is expected to re-read these values after receiving a
+configuration change notification.
+
 \begin{lstlisting}
 struct virtio_net_config {
         u8 mac[6];
         le16 status;
         le16 max_virtqueue_pairs;
         le16 mtu;
+        le32 speed;
+        u8 duplex;
+
 };
 \end{lstlisting}
 
@@ -2916,6 +2933,19 @@ \subsection{Device configuration layout}\label{sec:Device Types / Network Device
 If the driver negotiates the VIRTIO_NET_F_STANDBY feature, the device MAY act
 as a standby device for a primary device with the same MAC address.
 
+If VIRTIO_NET_F_SPEED_DUPLEX has been negotiated, \field{speed}
+MUST contain the device speed, in units of 1 MBit per second, 0 to
+0x7ffffffff, or 0xfffffffff for unknown.
+
+If VIRTIO_NET_F_SPEED_DUPLEX has been negotiated, \field{duplex}
+MUST have the values of 0x00 for full duplex, 0x01 for half
+duplex, or 0xff for unknown.
+
+If VIRTIO_NET_F_SPEED_DUPLEX and VIRTIO_NET_F_STATUS have both
+been negotiated, the device SHOULD NOT change the \field{speed} and
+\field{duplex} fields as long as VIRTIO_NET_S_LINK_UP is set in
+the \field{status}.
+
 \drivernormative{\subsubsection}{Device configuration layout}{Device Types / Network Device / Device configuration layout}
 
 A driver SHOULD negotiate VIRTIO_NET_F_MAC if the device offers it.
@@ -2940,6 +2970,15 @@ \subsection{Device configuration layout}\label{sec:Device Types / Network Device
 
 A driver SHOULD negotiate the VIRTIO_NET_F_STANDBY feature if the device offers it.
 
+If VIRTIO_NET_F_SPEED_DUPLEX has been negotiated,
+the driver MUST treat any value of \field{speed} above
+0x7fffffff as well as any value of \field{duplex} not
+matching 0x00 or 0x01 as an unknown value.
+
+If VIRTIO_NET_F_SPEED_DUPLEX has been negotiated, the driver
+SHOULD re-read \field{speed} and \field{duplex} after a
+configuration change notification.
+
 \subsubsection{Legacy Interface: Device configuration layout}\label{sec:Device Types / Network Device / Device configuration layout / Legacy Interface: Device configuration layout}
 \label{sec:Device Types / Block Device / Feature bits / Device configuration layout / Legacy Interface: Device configuration layout}
 When using the legacy interface, transitional devices and drivers
Signature · 7 lines
MST


---------------------------------------------------------------------
To unsubscribe from this mail list, you must leave the OASIS TC that 
generates this mail.  Follow this link to all your TCs in OASIS at:
https://www.oasis-open.org/apps/org/workgroup/portal/my_workgroups.php 
#1 lore raw
Quoted 14 lines · On Tue, 3 Dec 2019 05:39:23 -0500 "Michael S. Tsirkin" <[email protected]> wrote:

Document as used by Linux.

---

changes from v2:
fix up units
actually there's no way for driver to know that link up
changed: it might have changed back.
make the device requirement a weaker "SHOULD" and instead ask that driver re-read on each config change notification

Quoted 2 lines
 content.tex | 39 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)

Looks good to me.

---------------------------------------------------------------------
To unsubscribe from this mail list, you must leave the OASIS TC that generates this mail. Follow this link to all your TCs in OASIS at:
https://www.oasis-open.org/apps/org/workgroup/portal/my_workgroups.php