ath10k: restore QCA9880-AR1A (v1) detection
Subsystems (2)
PATCH 1/1 ath10k: restore QCA9880-AR1A (v1) detection
commit f8914a14623a79b73f72b2b1ee4cd9b2cb91b735 upstream
---
From f8914a14623a79b73f72b2b1ee4cd9b2cb91b735 Mon Sep 17 00:00:00 2001
From: Christian Lamparter <[email protected]>
Date: Mon, 25 Mar 2019 13:50:19 +0100
Subject: [PATCH 4.4] ath10k: restore QCA9880-AR1A (v1) detection
To: [email protected],
[email protected]
Cc: Kalle Valo <[email protected]>
This patch restores the old behavior that read
the chip_id on the QCA988x before resetting the
chip. This needs to be done in this order since
the unsupported QCA988x AR1A chips fall off the
bus when resetted. Otherwise the next MMIO Op
after the reset causes a BUS ERROR and panic.
--- drivers/net/wireless/ath/ath10k/pci.c | 36 +++++++++++++++++++-------- 1 file changed, 25 insertions(+), 11 deletions(-)
drivers/net/wireless/ath/ath10k/pci.c +21 -6
@@ -2988,12 +2988,13 @@ static int ath10k_pci_probe(struct pci_dstruct ath10k_pci *ar_pci;enum ath10k_hw_rev hw_rev;u32 chip_id; -bool pci_ps; +bool pci_ps, is_qca988x = false;switch (pci_dev->device) {case QCA988X_2_0_DEVICE_ID : hw_rev =ATH10K_HW_QCA988X ; pci_ps = false; + is_qca988x = true;break ;case QCA6164_2_1_DEVICE_ID :case QCA6174_2_1_DEVICE_ID :
@@ -3087,6 +3088,19 @@ static int ath10k_pci_probe(struct pci_d goto err_deinit_irq; } +/* Read CHIP_ID before reset to catch QCA9880-AR1A v1 devices that +* fall off the bus during chip_reset. These chips have the same pci +* device id as the QCA9880 BR4A or 2R4E. So that's why the check. +*/ +if (is_qca988x) { + chip_id =ath10k_pci_soc_read32 (ar,SOC_CHIP_ID_ADDRESS ); +if (chip_id !=0xffffffff ) { +if (!ath10k_pci_chip_is_supported (pdev->device, + chip_id)) + goto err_unsupported; + } + } + ret =ath10k_pci_chip_reset (ar);if (ret) {ath10k_err (ar,"failed to reset chip: %d\n" , ret);
@@ -3099,11 +3113,8 @@ static int ath10k_pci_probe(struct pci_d goto err_free_irq; } -if (!ath10k_pci_chip_is_supported (pdev->device, chip_id)) { -ath10k_err (ar,"device %04x with chip_id %08x isn't supported\n" , - pdev->device, chip_id); - goto err_free_irq; - } +if (!ath10k_pci_chip_is_supported (pdev->device, chip_id)) + goto err_unsupported; ret =ath10k_core_register (ar, chip_id);if (ret) {
@@ -3113,6 +3124,10 @@ static int ath10k_pci_probe(struct pci_dreturn 0 ; +err_unsupported: +ath10k_err (ar,"device %04x with chip_id %08x isn't supported\n" , + pdev->device, bus_params.chip_id); + err_free_irq:ath10k_pci_free_irq (ar);ath10k_pci_kill_tasklet (ar);
Greg KH
maintainerQuoted 77 lines · Christian Lamparter
commit
f8914a14623a79b73f72b2b1ee4cd9b2cb91b735upstream
---Quoted 1 line
From
f8914a14623a79b73f72b2b1ee4cd9b2cb91b735Mon Sep 17 00:00:00 2001From: Christian Lamparter <[email protected]>
Date: Mon, 25 Mar 2019 13:50:19 +0100
Subject: [PATCH 4.4] ath10k: restore QCA9880-AR1A (v1) detection
To: [email protected],
[email protected]
Cc: Kalle Valo <[email protected]>This patch restores the old behavior that read
thechip_idon the QCA988x before resetting the
chip. This needs to be done in this order since
the unsupported QCA988x AR1A chips fall off the
bus when resetted. Otherwise the next MMIO Op
after the reset causes a BUS ERROR and panic.Cc [email protected] # 4.4Fixes 1a7fecb766c8 ("ath10k: reset chip before reading chip_id in probe")Signed-off-by Christian Lamparter <[email protected]>--- drivers/net/wireless/ath/ath10k/pci.c | 36 +++++++++++++++++++-------- 1 file changed, 25 insertions(+), 11 deletions(-)drivers/net/wireless/ath/ath10k/pci.c +17
-6@@ -2988,12 +2988,13 @@ static int ath10k_pci_probe(struct pci_dstruct ath10k_pci *ar_pci;enum ath10k_hw_rev hw_rev;u32 chip_id; -bool pci_ps; +bool pci_ps, is_qca988x = false;switch (pci_dev->device) {case QCA988X_2_0_DEVICE_ID : hw_rev =ATH10K_HW_QCA988X ; pci_ps = false; + is_qca988x = true;break ;case QCA6164_2_1_DEVICE_ID :case QCA6174_2_1_DEVICE_ID :@@ -3087,6 +3088,19 @@ static int ath10k_pci_probe(struct pci_d goto err_deinit_irq; } +/* Read CHIP_ID before reset to catch QCA9880-AR1A v1 devices that +* fall off the bus during chip_reset. These chips have the same pci +* device id as the QCA9880 BR4A or 2R4E. So that's why the check. +*/ +if (is_qca988x) { + chip_id =ath10k_pci_soc_read32 (ar,SOC_CHIP_ID_ADDRESS ); +if (chip_id !=0xffffffff ) { +if (!ath10k_pci_chip_is_supported (pdev->device, + chip_id)) + goto err_unsupported; + } + } + ret =ath10k_pci_chip_reset (ar);if (ret) {ath10k_err (ar,"failed to reset chip: %d\n" , ret);@@ -3099,11 +3113,8 @@ static int ath10k_pci_probe(struct pci_d goto err_free_irq; } -if (!ath10k_pci_chip_is_supported (pdev->device, chip_id)) { -ath10k_err (ar,"device %04x with chip_id %08x isn't supported\n" , - pdev->device, chip_id); - goto err_free_irq; - } +if (!ath10k_pci_chip_is_supported (pdev->device, chip_id)) + goto err_unsupported; ret =ath10k_core_register (ar, chip_id);if (ret) {
drivers/net/wireless/ath/ath10k/pci.c static int ath10k_pci_probe(struct pci_d · line 3129
Quoted 6 lines
drivers/net/wireless/ath/ath10k/pci.c +3
-0@@ -3113,6 +3124,10 @@ static int ath10k_pci_probe(struct pci_dreturn 0 ; +err_unsupported: +ath10k_err (ar,"device %04x with chip_id %08x isn't supported\n" , + pdev->device, bus_params.chip_id);
Backports are great, but as I mentioned before, this breaks the build, so we can't take it:
drivers/net/wireless/ath/ath10k/pci.c: In function ‘ath10k_pci_probe’:drivers/net/wireless/ath/ath10k/pci.c:3129:20: error: ‘bus_params’ undeclared (first use in this function); did you mean ‘key_params’?
3129 | pdev->device, bus_params.chip_id);
| ^~~~~~~~~~
| key_paramsPlease fix this up and resend backports again.
thanks,
greg k-h
Quoted 89 lines · Greg KH
Quoted 77 lines · Christian Lamparter
commit
f8914a14623a79b73f72b2b1ee4cd9b2cb91b735upstream
---Quoted 1 line
From
f8914a14623a79b73f72b2b1ee4cd9b2cb91b735Mon Sep 17 00:00:00 2001From: Christian Lamparter <[email protected]>
Date: Mon, 25 Mar 2019 13:50:19 +0100
Subject: [PATCH 4.4] ath10k: restore QCA9880-AR1A (v1) detection
To: [email protected],
[email protected]
Cc: Kalle Valo <[email protected]>This patch restores the old behavior that read
thechip_idon the QCA988x before resetting the
chip. This needs to be done in this order since
the unsupported QCA988x AR1A chips fall off the
bus when resetted. Otherwise the next MMIO Op
after the reset causes a BUS ERROR and panic.Cc [email protected] # 4.4Fixes 1a7fecb766c8 ("ath10k: reset chip before reading chip_id in probe")Signed-off-by Christian Lamparter <[email protected]>--- drivers/net/wireless/ath/ath10k/pci.c | 36 +++++++++++++++++++-------- 1 file changed, 25 insertions(+), 11 deletions(-)drivers/net/wireless/ath/ath10k/pci.c 2019-09-08 00:17:15.365912133 +0200 renamed from drivers/net/wireless/ath/ath10k/pci.c 2019-09-08 00:07:21.374565470 +0200 +17
-6@@ -2988,12 +2988,13 @@ static int ath10k_pci_probe(struct pci_d struct ath10k_pci *ar_pci; enum ath10k_hw_rev hw_rev; u32 chip_id; - bool pci_ps; + bool pci_ps, is_qca988x = false; switch (pci_dev->device) { case QCA988X_2_0_DEVICE_ID: hw_rev = ATH10K_HW_QCA988X; pci_ps = false; + is_qca988x = true; break; case QCA6164_2_1_DEVICE_ID: case QCA6174_2_1_DEVICE_ID:@@ -3087,6 +3088,19 @@ static int ath10k_pci_probe(struct pci_d goto err_deinit_irq; } + /* Read CHIP_ID before reset to catch QCA9880-AR1A v1 devices that + * fall off the bus during chip_reset. These chips have the same pci + * device id as the QCA9880 BR4A or 2R4E. So that's why the check. + */ + if (is_qca988x) { + chip_id = ath10k_pci_soc_read32(ar, SOC_CHIP_ID_ADDRESS); + if (chip_id != 0xffffffff) { + if (!ath10k_pci_chip_is_supported(pdev->device, + chip_id)) + goto err_unsupported; + } + } + ret = ath10k_pci_chip_reset(ar); if (ret) { ath10k_err(ar, "failed to reset chip: %d\n", ret);@@ -3099,11 +3113,8 @@ static int ath10k_pci_probe(struct pci_d goto err_free_irq; } - if (!ath10k_pci_chip_is_supported(pdev->device, chip_id)) { - ath10k_err(ar, "device %04x with chip_id %08x isn't supported\n", - pdev->device, chip_id); - goto err_free_irq; - } + if (!ath10k_pci_chip_is_supported(pdev->device, chip_id)) + goto err_unsupported; ret = ath10k_core_register(ar, chip_id); if (ret) {drivers/net/wireless/ath/ath10k/pci.c 2019-09-08 00:17:15.365912133 +0200 static int ath10k_pci_probe(struct pci_d · line 3129
Quoted 6 lines
drivers/net/wireless/ath/ath10k/pci.c 2019-09-08 00:17:15.365912133 +0200 renamed from drivers/net/wireless/ath/ath10k/pci.c 2019-09-08 00:07:21.374565470 +0200 +3
-0@@ -3113,6 +3124,10 @@ static int ath10k_pci_probe(struct pci_d return 0; +err_unsupported: + ath10k_err(ar, "device %04x with chip_id %08x isn't supported\n", + pdev->device, bus_params.chip_id);Backports are great, but as I mentioned before, this breaks the build, so we can't take it:
Quoted 6 lines
drivers/net/wireless/ath/ath10k/pci.c: In function ‘ath10k_pci_probe’:drivers/net/wireless/ath/ath10k/pci.c:3129:20: error: ‘bus_params’ undeclared (first use in this function); did you mean ‘key_params’?3129 | pdev->device, bus_params.chip_id); | ^~~~~~~~~~ | key_params
Ok, I see. That "bus_params." there has to go so just "chip_id" remains.
But, I'm sorry that I caused this havoc.
For a little bit of background: Getting the QCA9880-AR1A and the board it works back, will
take until next year. Since this card either doesn't fit (it's oversized mini-pcie) or flat-out
doesn't work (it crashes the vast majority of x86/AMD64 system during post). So doing tests with the hardware involves going through custom OpenWrt-builds.
Quoted 1 line
Please fix this up and resend backports again.
I guess, I can do that. Question is, given the bug has been around since 2015 and the
response for this patch has been negative (even from those who have crashes from it).
I'm thinking that I'll rather drop this and take the time off by doing something else for
a while.
Yours,
Christian
Greg KH
maintainerQuoted 106 lines · Christian Lamparter
Quoted 89 lines · Greg KH
Quoted 77 lines · Christian Lamparter
commit
f8914a14623a79b73f72b2b1ee4cd9b2cb91b735upstream
---Quoted 1 line
From
f8914a14623a79b73f72b2b1ee4cd9b2cb91b735Mon Sep 17 00:00:00 2001From: Christian Lamparter <[email protected]>
Date: Mon, 25 Mar 2019 13:50:19 +0100
Subject: [PATCH 4.4] ath10k: restore QCA9880-AR1A (v1) detection
To: [email protected],
[email protected]
Cc: Kalle Valo <[email protected]>This patch restores the old behavior that read
thechip_idon the QCA988x before resetting the
chip. This needs to be done in this order since
the unsupported QCA988x AR1A chips fall off the
bus when resetted. Otherwise the next MMIO Op
after the reset causes a BUS ERROR and panic.Cc [email protected] # 4.4Fixes 1a7fecb766c8 ("ath10k: reset chip before reading chip_id in probe")Signed-off-by Christian Lamparter <[email protected]>--- drivers/net/wireless/ath/ath10k/pci.c | 36 +++++++++++++++++++-------- 1 file changed, 25 insertions(+), 11 deletions(-)drivers/net/wireless/ath/ath10k/pci.c 2019-09-08 00:17:15.365912133 +0200 renamed from drivers/net/wireless/ath/ath10k/pci.c 2019-09-08 00:07:21.374565470 +0200 +17
-6@@ -2988,12 +2988,13 @@ static int ath10k_pci_probe(struct pci_d struct ath10k_pci *ar_pci; enum ath10k_hw_rev hw_rev; u32 chip_id; - bool pci_ps; + bool pci_ps, is_qca988x = false; switch (pci_dev->device) { case QCA988X_2_0_DEVICE_ID: hw_rev = ATH10K_HW_QCA988X; pci_ps = false; + is_qca988x = true; break; case QCA6164_2_1_DEVICE_ID: case QCA6174_2_1_DEVICE_ID:@@ -3087,6 +3088,19 @@ static int ath10k_pci_probe(struct pci_d goto err_deinit_irq; } + /* Read CHIP_ID before reset to catch QCA9880-AR1A v1 devices that + * fall off the bus during chip_reset. These chips have the same pci + * device id as the QCA9880 BR4A or 2R4E. So that's why the check. + */ + if (is_qca988x) { + chip_id = ath10k_pci_soc_read32(ar, SOC_CHIP_ID_ADDRESS); + if (chip_id != 0xffffffff) { + if (!ath10k_pci_chip_is_supported(pdev->device, + chip_id)) + goto err_unsupported; + } + } + ret = ath10k_pci_chip_reset(ar); if (ret) { ath10k_err(ar, "failed to reset chip: %d\n", ret);@@ -3099,11 +3113,8 @@ static int ath10k_pci_probe(struct pci_d goto err_free_irq; } - if (!ath10k_pci_chip_is_supported(pdev->device, chip_id)) { - ath10k_err(ar, "device %04x with chip_id %08x isn't supported\n", - pdev->device, chip_id); - goto err_free_irq; - } + if (!ath10k_pci_chip_is_supported(pdev->device, chip_id)) + goto err_unsupported; ret = ath10k_core_register(ar, chip_id); if (ret) {drivers/net/wireless/ath/ath10k/pci.c 2019-09-08 00:17:15.365912133 +0200 static int ath10k_pci_probe(struct pci_d · line 3129
Quoted 6 lines
drivers/net/wireless/ath/ath10k/pci.c 2019-09-08 00:17:15.365912133 +0200 renamed from drivers/net/wireless/ath/ath10k/pci.c 2019-09-08 00:07:21.374565470 +0200 +3
-0@@ -3113,6 +3124,10 @@ static int ath10k_pci_probe(struct pci_d return 0; +err_unsupported: + ath10k_err(ar, "device %04x with chip_id %08x isn't supported\n", + pdev->device, bus_params.chip_id);Backports are great, but as I mentioned before, this breaks the build, so we can't take it:
Quoted 6 lines
drivers/net/wireless/ath/ath10k/pci.c: In function ‘ath10k_pci_probe’:drivers/net/wireless/ath/ath10k/pci.c:3129:20: error: ‘bus_params’ undeclared (first use in this function); did you mean ‘key_params’?3129 | pdev->device, bus_params.chip_id); | ^~~~~~~~~~ | key_paramsOk, I see. That "
bus_params." there has to go so just "chip_id" remains.But, I'm sorry that I caused this havoc.
For a little bit of background: Getting the QCA9880-AR1A and the board it works back, will
take until next year. Since this card either doesn't fit (it's oversized mini-pcie) or flat-out
doesn't work (it crashes the vast majority of x86/AMD64 system during post). So doing tests with the hardware involves going through custom OpenWrt-builds.
Quoted 8 lines
Quoted 1 line
Please fix this up and resend backports again.
I guess, I can do that. Question is, given the bug has been around since 2015 and the
response for this patch has been negative (even from those who have crashes from it).
I'm thinking that I'll rather drop this and take the time off by doing something else for
a while.
That's fine, if someone has noticed this, then they just can use a new kernel version.
thanks,
greg k-h