ram: add SDRAM driver for i.MXRT SoCs
Subsystems (6)
PATCH 16/20 ram: add SDRAM driver for i.MXRT SoCs
Add SDRAM driver for i.MXRT SoCs.
--- drivers/ram/Kconfig | 8 + drivers/ram/Makefile | 2 + drivers/ram/imxrt_sdram.c | 439 +++++++++++++++++++++++ include/dt-bindings/memory/imxrt-sdram.h | 100 ++++++ 4 files changed, 549 insertions(+) create mode 100644 drivers/ram/imxrt_sdram.c create mode 100644 include/dt-bindings/memory/imxrt-sdram.h
drivers/ram/Kconfig +8 -0
@@ -65,5 +65,13 @@ config K3_J721E_DDRSS Enabling this config adds support for the DDR memory controller on J721E family of SoCs. +config IMXRT_SDRAM + bool "Enable i.MXRT SDRAM support" + depends on RAM + help + i.MXRT family devices support smart external memory controller(SEMC) + to support external memories like sdram, psram & nand. + This driver is for the sdram memory interface with the SEMC. + source "drivers/ram/rockchip/Kconfig" source "drivers/ram/stm32mp1/Kconfig"
drivers/ram/Makefile +2 -0
@@ -15,3 +15,5 @@ obj-$(CONFIG_ARCH_ROCKCHIP) += rockchip/ obj-$(CONFIG_K3_AM654_DDRSS) += k3-am654-ddrss.o obj-$(CONFIG_ARCH_MEDIATEK) += mediatek/ obj-$(CONFIG_K3_J721E_DDRSS) += k3-j721e/ + +obj-$(CONFIG_IMXRT_SDRAM) += imxrt_sdram.o
drivers/ram/imxrt_sdram.c new file +439 -0
439 lines not on this page · raw message
include/dt-bindings/memory/imxrt-sdram.h new file +100 -0
100 lines not on this page · raw message
Signature · 1 line
2.20.1
PATCH 17/20 mmc: fsl_esdhc: make if(CONFIG_IS_ENABLED(CLK)) an #if statement
Not all architectures(i.e. i.MXRT) support mxc_get_clock() and use DM_CLK instead. So building could result in failure due to missing mxc_get_clock().
Make if(CONFIG_IS_ENABLED(CLK)) an #if statement.
--- drivers/mmc/fsl_esdhc_imx.c | 38 ++++++++++++++++++------------------- 1 file changed, 19 insertions(+), 19 deletions(-)
drivers/mmc/fsl_esdhc_imx.c +19 -19
@@ -1514,27 +1514,27 @@ static int fsl_esdhc_probe(struct udevice *dev)init_clk_usdhc (dev->seq); -if (CONFIG_IS_ENABLED (CLK )) { -/* Assigned clock already set clock */ - ret =clk_get_by_name (dev,"per" , &priv->per_clk); -if (ret) { -printf ("Failed to get per_clk\n" ); -return ret; - } - ret =clk_enable (&priv->per_clk); -if (ret) { -printf ("Failed to enable per_clk\n" ); -return ret; - } +#if CONFIG_IS_ENABLED (CLK ) +/* Assigned clock already set clock */ + ret =clk_get_by_name (dev,"per" , &priv->per_clk); +if (ret) { +printf ("Failed to get per_clk\n" ); +return ret; + } + ret =clk_enable (&priv->per_clk); +if (ret) { +printf ("Failed to enable per_clk\n" ); +return ret; + } - priv->sdhc_clk =clk_get_rate (&priv->per_clk); - }else { - priv->sdhc_clk =mxc_get_clock (MXC_ESDHC_CLK + dev->seq); -if (priv->sdhc_clk <=0 ) { -dev_err (dev,"Unable to get clk for %s\n" , dev->name); -return -EINVAL ; - } + priv->sdhc_clk =clk_get_rate (&priv->per_clk); +#else + priv->sdhc_clk =mxc_get_clock (MXC_ESDHC_CLK + dev->seq); +if (priv->sdhc_clk <=0 ) { +dev_err (dev,"Unable to get clk for %s\n" , dev->name); +return -EINVAL ; } +#endif ret =fsl_esdhc_init (priv, plat);if (ret) {
Signature · 1 line
2.20.1
PATCH 18/20 mmc: fsl_esdhc: add compatible for fsl, imxrt-usdhc
In reply to Giulio BenettiAdd compatible "fsl,imxrt-usdhc" to make mmc working on i.MXRT platforms with CONFIG_DM_MMC=y.
--- drivers/mmc/Kconfig | 2 +- drivers/mmc/fsl_esdhc_imx.c | 3 ++- 2 files changed, 3 insertions(+), 2 deletions(-)
drivers/mmc/Kconfig +1 -1
@@ -732,7 +732,7 @@ config FSL_ESDHC_IMX config FSL_USDHC bool "Freescale/NXP i.MX uSDHC controller support" - depends on MX6 || MX7 ||ARCH_MX7ULP || IMX8 || IMX8M || TARGET_S32V234EVB + depends on MX6 || MX7 ||ARCH_MX7ULP || IMX8 || IMX8M || TARGET_S32V234EVB || ARCH_IMXRT select FSL_ESDHC_IMX help This enables the Ultra Secured Digital Host Controller enhancements
drivers/mmc/fsl_esdhc_imx.c +2 -1
@@ -78,7 +78,7 @@ struct fsl_esdhc {uint vendorspec;uint mmcboot;uint vendorspec2; -uint tuning_ctrl;/* on i.MX6/7/8 */ +uint tuning_ctrl;/* on i.MX6/7/8/RT */ char reserved5[44 ];uint hostver;/* Host controller version register */ char reserved6[4 ];/* reserved */
@@ -1651,6 +1651,7 @@ static const struct udevice_id fsl_esdhc_ids[] = { { .compatible = "fsl,imx8mm-usdhc", .data = (ulong)&usdhc_imx8qm_data,}, { .compatible = "fsl,imx8mn-usdhc", .data = (ulong)&usdhc_imx8qm_data,}, { .compatible = "fsl,imx8mq-usdhc", .data = (ulong)&usdhc_imx8qm_data,}, + { .compatible = "fsl,imxrt-usdhc", }, { .compatible = "fsl,esdhc", }, { /* sentinel */ } };
Signature · 1 line
2.20.1
PATCH 19/20 imx: Add basic support for the NXP IMXRT10xx SoC family
In reply to Giulio BenettiAdd i.IMXRT family basic support.
--- arch/arm/Kconfig | 10 ++++++ arch/arm/Makefile | 4 +-- arch/arm/include/asm/arch-imxrt/clock.h | 10 ++++++ arch/arm/include/asm/arch-imxrt/gpio.h | 19 +++++++++++ arch/arm/include/asm/arch-imxrt/imx-regs.h | 20 ++++++++++++ arch/arm/include/asm/arch-imxrt/imxrt.h | 11 +++++++ arch/arm/include/asm/arch-imxrt/sys_proto.h | 11 +++++++ arch/arm/mach-imx/Makefile | 3 +- arch/arm/mach-imx/imxrt/Kconfig | 21 +++++++++++++ arch/arm/mach-imx/imxrt/Makefile | 7 +++++ arch/arm/mach-imx/imxrt/soc.c | 35 +++++++++++++++++++++ 11 files changed, 148 insertions(+), 3 deletions(-) create mode 100644 arch/arm/include/asm/arch-imxrt/clock.h create mode 100644 arch/arm/include/asm/arch-imxrt/gpio.h create mode 100644 arch/arm/include/asm/arch-imxrt/imx-regs.h create mode 100644 arch/arm/include/asm/arch-imxrt/imxrt.h create mode 100644 arch/arm/include/asm/arch-imxrt/sys_proto.h create mode 100644 arch/arm/mach-imx/imxrt/Kconfig create mode 100644 arch/arm/mach-imx/imxrt/Makefile create mode 100644 arch/arm/mach-imx/imxrt/soc.c
arch/arm/Kconfig +10 -0
@@ -797,6 +797,14 @@ config ARCH_IMX8M select SUPPORT_SPL imply CMD_DM +config ARCH_IMXRT + bool "NXP i.MXRT platform" + select CPU_V7M + select DM + select DM_SERIAL + select SUPPORT_SPL + imply CMD_DM + config ARCH_MX23 bool "NXP i.MX23 family" select CPU_ARM926EJS
@@ -1720,6 +1728,8 @@ source "arch/arm/mach-imx/imx8/Kconfig" source "arch/arm/mach-imx/imx8m/Kconfig" +source "arch/arm/mach-imx/imxrt/Kconfig" + source "arch/arm/mach-imx/mxs/Kconfig" source "arch/arm/mach-omap2/Kconfig"
arch/arm/Makefile +2 -2
@@ -104,11 +104,11 @@ libs-y += arch/arm/cpu/ libs-y += arch/arm/lib/ ifeq ($(CONFIG_SPL_BUILD),y) -ifneq (,$(CONFIG_MX23)$(CONFIG_MX28)$(CONFIG_MX35)$(filter $(SOC), mx25 mx5 mx6 mx7 mx35 imx8m imx8)) +ifneq (,$(CONFIG_MX23)$(CONFIG_MX28)$(CONFIG_MX35)$(filter $(SOC), mx25 mx5 mx6 mx7 mx35 imx8m imx8 imxrt)) libs-y += arch/arm/mach-imx/ endif else -ifneq (,$(filter $(SOC), mx25 mx27 mx5 mx6 mx7 mx7ulp mx31 mx35 mxs imx8m imx8 vf610)) +ifneq (,$(filter $(SOC), mx25 mx27 mx5 mx6 mx7 mx7ulp mx31 mx35 mxs imx8m imx8 imxrt vf610)) libs-y += arch/arm/mach-imx/ endif endif
arch/arm/include/asm/arch-imxrt/clock.h new file +10 -0
@@ -0,0 +1,10 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (C) 2019 +* Author(s): Giulio Benetti <[email protected]> +*/ + +#ifndef __ASM_ARCH_CLOCK_H +#define __ASM_ARCH_CLOCK_H + +#endif /* __ASM_ARCH_CLOCK_H */
arch/arm/include/asm/arch-imxrt/gpio.h new file +19 -0
@@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (C) 2019 +* Author(s): Giulio Benetti <[email protected]> +*/ + +#ifndef __ASM_ARCH_GPIO_H__ +#define __ASM_ARCH_GPIO_H__ + +#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__)) +/* GPIO registers */ +struct gpio_regs { +u32 gpio_dr;/* data */ +u32 gpio_dir;/* direction */ +u32 gpio_psr;/* pad satus */ +}; +#endif + +#endif /* __ASM_ARCH_GPIO_H__ */
arch/arm/include/asm/arch-imxrt/imx-regs.h new file +20 -0
@@ -0,0 +1,20 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright(C) 2019 +* Author(s): Giulio Benetti <[email protected]> +*/ + +#ifndef __ASM_ARCH_IMX_REGS_H__ +#define __ASM_ARCH_IMX_REGS_H__ + +#define ARCH_MXC + +#define ANATOP_BASE_ADDR 0x400d8000 + +#define MXS_LCDIF_BASE 0x402b8000 + +#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__)) +#include <asm/mach-imx/regs-lcdif.h> +#endif + +#endif /* __ASM_ARCH_IMX_REGS_H__ */
arch/arm/include/asm/arch-imxrt/imxrt.h new file +11 -0
@@ -0,0 +1,11 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (C) 2019 +* Author(s): Giulio Benetti <[email protected]> +*/ + +#ifndef _ASM_ARCH_IMXRT_H +#define _ASM_ARCH_IMXRT_H + +#endif /* _ASM_ARCH_IMXRT_H */ +
arch/arm/include/asm/arch-imxrt/sys_proto.h new file +11 -0
@@ -0,0 +1,11 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (C) 2017 NXP +*/ + +#ifndef _ASM_ARCH_SYS_PROTO_H +#define _ASM_ARCH_SYS_PROTO_H + +#include <asm/mach-imx/sys_proto.h> + +#endif /* _ASM_ARCH_SYS_PROTO_H */
arch/arm/mach-imx/Makefile +2 -1
@@ -27,7 +27,7 @@ endif obj-$(CONFIG_GPT_TIMER) += timer.o obj-$(CONFIG_SYS_I2C_MXC) += i2c-mxv7.o endif -ifeq ($(SOC),$(filter $(SOC),mx7 mx6 mxs imx8m imx8)) +ifeq ($(SOC),$(filter $(SOC),mx7 mx6 mxs imx8m imx8 imxrt)) obj-y += misc.o obj-$(CONFIG_SPL_BUILD) += spl.o endif
@@ -226,5 +226,6 @@ obj-$(CONFIG_MX7) += mx7/ obj-$(CONFIG_ARCH_MX7ULP) += mx7ulp/ obj-$(CONFIG_IMX8M) += imx8m/ obj-$(CONFIG_ARCH_IMX8) += imx8/ +obj-$(CONFIG_ARCH_IMXRT) += imxrt/ obj-$(CONFIG_SPL_BOOTROM_SUPPORT) += spl_imx_romapi.o
arch/arm/mach-imx/imxrt/Kconfig new file +21 -0
@@ -0,0 +1,21 @@ +if ARCH_IMXRT + +config IMXRT1050 + bool + +config SYS_SOC + default "imxrt" + +choice + prompt "NXP i.MXRT board select" + optional + +config TARGET_IMXRT1050_EVK + bool "Support imxrt1050 EVK board" + select IMXRT1050 + +endchoice + +source "board/freescale/imxrt1050-evk/Kconfig" + +endif
arch/arm/mach-imx/imxrt/Makefile new file +7 -0
@@ -0,0 +1,7 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# (C) Copyright 2019 +# Author(s): Giulio Benetti <[email protected]> +# + +obj-y := soc.o
arch/arm/mach-imx/imxrt/soc.c new file +35 -0
@@ -0,0 +1,35 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2019 +* Author(s): Giulio Benetti <[email protected]> +*/ + +#include <common.h> +#include <asm/io.h> +#include <asm/armv7_mpu.h> + +int arch_cpu_init (void ) +{ +int i; + +struct mpu_region_config imxrt1050_region_config[] = { + {0x00000000 ,REGION_0 ,XN_DIS ,PRIV_RW_USR_RW , +STRONG_ORDER ,REGION_4GB }, + {PHYS_SDRAM ,REGION_1 ,XN_DIS ,PRIV_RW_USR_RW , +O_I_WB_RD_WR_ALLOC , (ffs (PHYS_SDRAM_SIZE ) -2 ) }, + {DMAMEM_BASE , +REGION_2 ,XN_DIS ,PRIV_RW_USR_RW , +STRONG_ORDER , (ffs (DMAMEM_SZ_ALL ) -2 ) }, + }; + +/* +* Configure the memory protection unit (MPU) to allow full access to +* the whole 4GB address space. +*/ +disable_mpu (); +for (i =0 ; i <ARRAY_SIZE (imxrt1050_region_config); i++) +mpu_config (&imxrt1050_region_config[i]); +enable_mpu (); + +return 0 ; +}
Signature · 1 line
2.20.1
PATCH 20/20 imx: imxrt1050-evk: Add support for the NXP i.MXRT1050-EVK
In reply to Giulio BenettiThis commit adds board support for i.MXRT1050-EVK from NXP. This board is an evaluation kit provided by NXP for i.MXRT105x processor family.
More information about this board can be found here:
https://www.nxp.com/design/development-boards/i.mx-evaluation-and-development-boards/i.mx-rt1050-evaluation-kit:MIMXRT1050-EVK
The initial supported/tested devices include:
- Debug serial
- SD
--- arch/arm/dts/Makefile | 2 + arch/arm/dts/imxrt1050-evk.dts | 209 ++++++++++++++++++ board/freescale/imxrt1050-evk/Kconfig | 22 ++ board/freescale/imxrt1050-evk/MAINTAINERS | 6 + board/freescale/imxrt1050-evk/Makefile | 6 + board/freescale/imxrt1050-evk/README | 31 +++ board/freescale/imxrt1050-evk/imximage.cfg | 36 +++ board/freescale/imxrt1050-evk/imxrt1050-evk.c | 81 +++++++ configs/imxrt1050-evk_defconfig | 74 +++++++ include/configs/imxrt1050-evk.h | 59 +++++ 10 files changed, 526 insertions(+) create mode 100644 arch/arm/dts/imxrt1050-evk.dts create mode 100644 board/freescale/imxrt1050-evk/Kconfig create mode 100644 board/freescale/imxrt1050-evk/MAINTAINERS create mode 100644 board/freescale/imxrt1050-evk/Makefile create mode 100644 board/freescale/imxrt1050-evk/README create mode 100644 board/freescale/imxrt1050-evk/imximage.cfg create mode 100644 board/freescale/imxrt1050-evk/imxrt1050-evk.c create mode 100644 configs/imxrt1050-evk_defconfig create mode 100644 include/configs/imxrt1050-evk.h
arch/arm/dts/Makefile +2 -0
@@ -672,6 +672,8 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mn-ddr4-evk.dtb \ imx8mq-evk.dtb +dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb + dtb-$(CONFIG_RCAR_GEN2) += \ r8a7790-lager-u-boot.dtb \ r8a7790-stout-u-boot.dtb \
arch/arm/dts/imxrt1050-evk.dts new file +209 -0
209 lines not on this page · raw message
board/freescale/imxrt1050-evk/Kconfig new file +22 -0
@@ -0,0 +1,22 @@ +if TARGET_IMXRT1050_EVK + +config SYS_BOARD + string + default "imxrt1050-evk" + +config SYS_VENDOR + string + default "freescale" + +config SYS_SOC + string + default "imxrt1050" + +config SYS_CONFIG_NAME + string + default "imxrt1050-evk" + +config IMX_CONFIG + default "board/freescale/imxrt1050-evk/imximage.cfg" + +endif
board/freescale/imxrt1050-evk/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +IMXRT1050 EVALUATION KIT +M: Giulio Benetti <[email protected]> +S: Maintained +F: board/freescale/imxrt1050-evk +F: include/configs/imxrt1050-evk.h +F: configs/imxrt1050-evk_defconfig
board/freescale/imxrt1050-evk/Makefile new file +6 -0
@@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2019 +# Author(s): Giulio Benetti <[email protected]> + +obj-y := imxrt1050-evk.o
board/freescale/imxrt1050-evk/README new file +31 -0
@@ -0,0 +1,31 @@ +How to use U-Boot on NXP i.MXRT1050 EVK +----------------------------------------------- + +- Build U-Boot for i.MXRT1050 EVK: + +$ make mrproper +$ make imxrt1050-evk_defconfig +$ make + +This will generate the SPL image called SPL and the u-boot.img. + +- Flash the SPL image into the micro SD card: + +sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync + +- Flash the u-boot.img image into the micro SD card: + +sudo dd if=u-boot.img of=/dev/sdb bs=1k seek=128; sync + +- Jumper settings: + +SW7: 1 0 1 0 + +where 0 means bottom position and 1 means top position (from the +switch label numbers reference). + +- Connect the USB cable between the EVK and the PC for the console. +(The USB console connector is the one close the ethernet connector) + +- Insert the micro SD card in the board, power it up and U-Boot messages should +come up.
board/freescale/imxrt1050-evk/imximage.cfg new file +36 -0
@@ -0,0 +1,36 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2019 + * Author(s): Giulio Benetti <[email protected]> + */ + +#define __ASSEMBLY__ +#include <config.h> + +/* image version */ + +IMAGE_VERSION 2 + +/* + * Boot Device : one of + * spi/sd/nand/onenand, qspi/nor + */ + +BOOT_FROM sd + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ + +/* Set all FlexRAM as OCRAM(01b) */ +DATA 4 0x400AC044 0x55555555 +/* Use FLEXRAM_BANK_CFG to config FlexRAM */ +SET_BIT 4 0x400AC040 0x4
board/freescale/imxrt1050-evk/imxrt1050-evk.c new file +81 -0
81 lines not on this page · raw message
configs/imxrt1050-evk_defconfig new file +74 -0
74 lines not on this page · raw message
include/configs/imxrt1050-evk.h new file +59 -0
59 lines not on this page · raw message
Signature · 1 line
2.20.1