tools/imximage: share DCD information via Kconfig
Subsystems (3)
PATCH 1/1 tools/imximage: share DCD information via Kconfig
IMX based platforms can have the DCD table located on different addresses due to differences in their memory maps (ie iMX7ULP).
This information is required by the user to sign the images for secure boot so continue making it accessible via mkimage.
--- arch/arm/mach-imx/Kconfig | 11 +++++++++++ tools/imximage.c | 5 +++-- 2 files changed, 14 insertions(+), 2 deletions(-)
arch/arm/mach-imx/Kconfig +11 -0
@@ -113,3 +113,14 @@ config DDRMC_VF610_CALIBRATION config SPL_IMX_ROMAPI_LOADADDR hex "Default load address to load image through ROM API" depends on IMX8MN + +config IMX_DCD_ADDR + hex "DCD Blocks location on the image" + default 0x00910000 if !ARCH_MX7ULP + default 0x2f010000 if ARCH_MX7ULP + help + Indicates where the Device Configuration Data, a binary table used by + the ROM code to configure the device at early boot stage, is located. + This information is shared with the user via mkimage -l just so the + image can be signed. +
tools/imximage.c +3 -2
@@ -11,6 +11,7 @@#include "imagetool.h" #include <image.h> #include "imximage.h" +#include <generated/autoconf.h> #define UNDEFINED 0xFFFFFFFF
@@ -524,8 +525,8 @@ static void print_hdr_v2(struct imx_header *imx_hdr)printf ("HAB Blocks: 0x%08x 0x%08x 0x%08x\n" , (uint32_t )fhdr_v2->self,0 , (uint32_t )(fhdr_v2->csf - fhdr_v2->self)); -printf ("DCD Blocks: 0x00910000 0x%08x 0x%08x\n" , - offs,be16_to_cpu (dcdlen)); +printf ("DCD Blocks: 0x%08x 0x%08x 0x%08x\n" , + offs,CONFIG_IMX_DCD_ADDR ,be16_to_cpu (dcdlen)); } }else {imx_header_v2_t *next_hdr_v2;
Signature · 1 line
2.17.1
Fabio Estevam
reviewerPATCH 1/1 tools/imximage: share DCD information via Kconfig
Quoted 8 lines · Jorge Ramirez-Ortiz
IMX based platforms can have the DCD table located on different addresses due to differences in their memory maps (ie iMX7ULP).
This information is required by the user to sign the images for secure boot so continue making it accessible via mkimage.
Signed-off-by Jorge Ramirez-Ortiz <[email protected]>
Stefano,
This is a bug fix for 2020.01.
Thanks
PATCH 1/1 tools/imximage: share DCD information via Kconfig
Hi Jorge, Fabio,
Quoted 8 lines · Fabio Estevam
Quoted 7 lines · Jorge Ramirez-Ortiz
IMX based platforms can have the DCD table located on different addresses due to differences in their memory maps (ie iMX7ULP).
This information is required by the user to sign the images for secure boot so continue making it accessible via mkimage.
Quoted 8 lines
Quoted 1 line
Signed-off-by Jorge Ramirez-Ortiz <[email protected]>Reviewed-by Fabio Estevam <[email protected]>Stefano,
This is a bug fix for 2020.01.
It is, but CONFIG_IMX_DCD_ADDR is then undefined for all architectures outside i.MX (because the config does not run), while imximage.c is always built. Then outside i.MX leads to broken build. I would at least add in imximage a check if it is not set and set it to the default value, like:
#if !defined(CONFIG_IMX_DCD_ADDR)
#define CONFIG_IMX_DCD_ADDR 0x00910000
#endif
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH 1/1 tools/imximage: share DCD information via Kconfig
In reply to Jorge Ramirez-OrtizQuoted 6 lines
IMX based platforms can have the DCD table located on different addresses due to differences in their memory maps (ie iMX7ULP). This information is required by the user to sign the images for secure boot so continue making it accessible via mkimage.
Signed-off-by Jorge Ramirez-Ortiz <[email protected]>Reviewed-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================