Skip to contentSkip to conversation

scsi: mpt3sas: Fix clear pending bit in ioctl status

PATCH New Sasha Levin 1 participant 42 messages Dec 11, 2019

Subsystems (11)
lore
Share & tools
lore

Sasha Levin

author maintainer
#0 lore raw

PATCH 1/42 scsi: mpt3sas: Fix clear pending bit in ioctl status

From: Sreekanth Reddy <[email protected]>

[ Upstream commit 782b281883caf70289ba6a186af29441a117d23e ]

When user issues diag register command from application with required size, and if driver unable to allocate the memory, then it will fail the register command. While failing the register command, driver is not currently clearing MPT3_CMD_PENDING bit in ctl_cmds.status variable which was set before trying to allocate the memory. As this bit is set, subsequent register command will be failed with BUSY status even when user wants to register the trace buffer will less memory.

Clear MPT3_CMD_PENDING bit in ctl_cmds.status before returning the diag register command with no memory status.

---
 drivers/scsi/mpt3sas/mpt3sas_ctl.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/scsi/mpt3sas/mpt3sas_ctl.c +2 -1
index 26cdc127ac89c..90a87e59ff602 100644
@@ -1465,7 +1465,8 @@ _ctl_diag_register_2(struct MPT3SAS_ADAPTER *ioc,
 			    " for diag buffers, requested size(%d)\n",
 			    ioc->name, __func__, request_data_sz);
 			mpt3sas_base_free_smid(ioc, smid);
-			return -ENOMEM;
+			rc = -ENOMEM;
+			goto out;
 		}
 		ioc->diag_buffer[buffer_type] = request_data;
 		ioc->diag_buffer_sz[buffer_type] = request_data_sz;
Signature · 1 line
2.20.1
author maintainer
#1 lore raw

PATCH 2/42 scsi: lpfc: Fix locking on mailbox command completion

From: James Smart <[email protected]>

[ Upstream commit 07b8582430370097238b589f4e24da7613ca6dd3 ]

Symptoms were seen of the driver not having valid data for mailbox commands. After debugging, the following sequence was found:

The driver maintains a port-wide pointer of the mailbox command that is currently in execution. Once finished, the port-wide pointer is cleared (done in lpfc_sli4_mq_release()). The next mailbox command issued will set the next pointer and so on.

The mailbox response data is only copied if there is a valid port-wide pointer.

In the failing case, it was seen that a new mailbox command was being attempted in parallel with the completion. The parallel path was seeing the mailbox no long in use (flag check under lock) and thus set the port pointer. The completion path had cleared the active flag under lock, but had not touched the port pointer. The port pointer is cleared after the lock is released. In this case, the completion path cleared the just-set value by the parallel path.

Fix by making the calls that clear mbox state/port pointer while under lock. Also slightly cleaned up the error path.

---
 drivers/scsi/lpfc/lpfc_sli.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
drivers/scsi/lpfc/lpfc_sli.c +7 -1
index e1e0feb250031..1eb9d5f6cea05 100644
@@ -11962,13 +11962,19 @@ send_current_mbox:
 	phba->sli.sli_flag &= ~LPFC_SLI_MBOX_ACTIVE;
 	/* Setting active mailbox pointer need to be in sync to flag clear */
 	phba->sli.mbox_active = NULL;
+	if (bf_get(lpfc_trailer_consumed, mcqe))
+		lpfc_sli4_mq_release(phba->sli4_hba.mbx_wq);
 	spin_unlock_irqrestore(&phba->hbalock, iflags);
 	/* Wake up worker thread to post the next pending mailbox command */
 	lpfc_worker_wake_up(phba);
+	return workposted;
+
 out_no_mqe_complete:
+	spin_lock_irqsave(&phba->hbalock, iflags);
 	if (bf_get(lpfc_trailer_consumed, mcqe))
 		lpfc_sli4_mq_release(phba->sli4_hba.mbx_wq);
-	return workposted;
+	spin_unlock_irqrestore(&phba->hbalock, iflags);
+	return false;
 }
 
 /**
Signature · 1 line
2.20.1
author maintainer
#2 lore raw

PATCH 3/42 Input: atmel_mxt_ts - disable IRQ across suspend

In reply to Sasha Levin

From: Evan Green <[email protected]>

[ Upstream commit 463fa44eec2fef50d111ed0199cf593235065c04 ]

Across suspend and resume, we are seeing error messages like the following:

atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121) atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)

This occurs because the driver leaves its IRQ enabled. Upon resume, there is an IRQ pending, but the interrupt is serviced before both the driver and the underlying I2C bus have been resumed. This causes EREMOTEIO errors.

Disable the IRQ in suspend, and re-enable it on resume. If there are cases where the driver enters suspend with interrupts disabled, that's a bug we should fix separately.

---
 drivers/input/touchscreen/atmel_mxt_ts.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/input/touchscreen/atmel_mxt_ts.c +4 -0
index c2fb0236a47cc..8d871fcb7912a 100644
@@ -3206,6 +3206,8 @@ static int __maybe_unused mxt_suspend(struct device *dev)
 
 	mutex_unlock(&input_dev->mutex);
 
+	disable_irq(data->irq);
+
 	return 0;
 }
 
@@ -3218,6 +3220,8 @@ static int __maybe_unused mxt_resume(struct device *dev)
 	if (!input_dev)
 		return 0;
 
+	enable_irq(data->irq);
+
 	mutex_lock(&input_dev->mutex);
 
 	if (input_dev->users)
Signature · 1 line
2.20.1
author maintainer
#3 lore raw

PATCH 4/42 iommu/tegra-smmu: Fix page tables in > 4 GiB memory

In reply to Sasha Levin

From: Thierry Reding <[email protected]>

[ Upstream commit 96d3ab802e4930a29a33934373157d6dff1b2c7e ]

Page tables that reside in physical memory beyond the 4 GiB boundary are currently not working properly. The reason is that when the physical address for page directory entries is read, it gets truncated at 32 bits and can cause crashes when passing that address to the DMA API.

Fix this by first casting the PDE value to a dma_addr_t and then using the page frame number mask for the SMMU instance to mask out the invalid bits, which are typically used for mapping attributes, etc.

---
 drivers/iommu/tegra-smmu.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)
drivers/iommu/tegra-smmu.c +6 -5
index c4eb293b15242..04cec050e42bf 100644
@@ -153,9 +153,9 @@ static bool smmu_dma_addr_valid(struct tegra_smmu *smmu, dma_addr_t addr)
 	return (addr & smmu->pfn_mask) == addr;
 }
 
-static dma_addr_t smmu_pde_to_dma(u32 pde)
+static dma_addr_t smmu_pde_to_dma(struct tegra_smmu *smmu, u32 pde)
 {
-	return pde << 12;
+	return (dma_addr_t)(pde & smmu->pfn_mask) << 12;
 }
 
 static void smmu_flush_ptc_all(struct tegra_smmu *smmu)
@@ -540,6 +540,7 @@ static u32 *tegra_smmu_pte_lookup(struct tegra_smmu_as *as, unsigned long iova,
 				  dma_addr_t *dmap)
 {
 	unsigned int pd_index = iova_pd_index(iova);
+	struct tegra_smmu *smmu = as->smmu;
 	struct page *pt_page;
 	u32 *pd;
 
@@ -548,7 +549,7 @@ static u32 *tegra_smmu_pte_lookup(struct tegra_smmu_as *as, unsigned long iova,
 		return NULL;
 
 	pd = page_address(as->pd);
-	*dmap = smmu_pde_to_dma(pd[pd_index]);
+	*dmap = smmu_pde_to_dma(smmu, pd[pd_index]);
 
 	return tegra_smmu_pte_offset(pt_page, iova);
 }
@@ -590,7 +591,7 @@ static u32 *as_get_pte(struct tegra_smmu_as *as, dma_addr_t iova,
 	} else {
 		u32 *pd = page_address(as->pd);
 
-		*dmap = smmu_pde_to_dma(pd[pde]);
+		*dmap = smmu_pde_to_dma(smmu, pd[pde]);
 	}
 
 	return tegra_smmu_pte_offset(as->pts[pde], iova);
@@ -615,7 +616,7 @@ static void tegra_smmu_pte_put_use(struct tegra_smmu_as *as, unsigned long iova)
 	if (--as->count[pde] == 0) {
 		struct tegra_smmu *smmu = as->smmu;
 		u32 *pd = page_address(as->pd);
-		dma_addr_t pte_dma = smmu_pde_to_dma(pd[pde]);
+		dma_addr_t pte_dma = smmu_pde_to_dma(smmu, pd[pde]);
 
 		tegra_smmu_set_pde(as, iova, 0);
 
Signature · 1 line
2.20.1
author maintainer
#4 lore raw

PATCH 5/42 scsi: target: compare full CHAP_A Algorithm strings

In reply to Sasha Levin

From: David Disseldorp <[email protected]>

[ Upstream commit 9cef2a7955f2754257a7cddedec16edae7b587d0 ]

RFC 2307 states:

For CHAP [RFC1994], in the first step, the initiator MUST send:

      CHAP_A=<A1,A2...>

Where A1,A2... are proposed algorithms, in order of preference.
...
For the Algorithm, as stated in [RFC1994], one value is required to be implemented:

5 (CHAP with MD5)

LIO currently checks for this value by only comparing a single byte in the tokenized Algorithm string, which means that any value starting with a '5' (e.g. "55") is interpreted as "CHAP with MD5". Fix this by comparing the entire tokenized string.

---
 drivers/target/iscsi/iscsi_target_auth.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/target/iscsi/iscsi_target_auth.c +1 -1
index f0d97305575d7..aa3f98994c7d6 100644
@@ -74,7 +74,7 @@ static int chap_check_algorithm(const char *a_str)
 		if (!token)
 			goto out;
 
-		if (!strncmp(token, "5", 1)) {
+		if (!strcmp(token, "5")) {
 			pr_debug("Selected MD5 Algorithm\n");
 			kfree(orig);
 			return CHAP_DIGEST_MD5;
Signature · 1 line
2.20.1
author maintainer
#5 lore raw

PATCH 6/42 scsi: lpfc: Fix SLI3 hba in loop mode not discovering devices

In reply to Sasha Levin

From: James Smart <[email protected]>

[ Upstream commit feff8b3d84d3d9570f893b4d83e5eab6693d6a52 ]

When operating in private loop mode, PLOGI exchanges are racing and the driver tries to abort it's PLOGI. But the PLOGI abort ends up terminating the login with the other end causing the other end to abort its PLOGI as well. Discovery never fully completes.

Fix by disabling the PLOGI abort when private loop and letting the state machine play out.

---
 drivers/scsi/lpfc/lpfc_nportdisc.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/scsi/lpfc/lpfc_nportdisc.c +3 -1
index 21ec7b5b6c85c..fefef2884d590 100644
@@ -454,8 +454,10 @@ lpfc_rcv_plogi(struct lpfc_vport *vport, struct lpfc_nodelist *ndlp,
 	 * single discovery thread, this will cause a huge delay in
 	 * discovery. Also this will cause multiple state machines
 	 * running in parallel for this node.
+	 * This only applies to a fabric environment.
 	 */
-	if (ndlp->nlp_state == NLP_STE_PLOGI_ISSUE) {
+	if ((ndlp->nlp_state == NLP_STE_PLOGI_ISSUE) &&
+	    (vport->fc_flag & FC_FABRIC)) {
 		/* software abort outstanding PLOGI */
 		lpfc_els_abort(phba, ndlp);
 	}
Signature · 1 line
2.20.1
author maintainer
#6 lore raw

PATCH 7/42 scsi: csiostor: Don't enable IRQs too early

In reply to Sasha Levin

From: Dan Carpenter <[email protected]>

[ Upstream commit d6c9b31ac3064fbedf8961f120a4c117daa59932 ]

These are called with IRQs disabled from csio_mgmt_tmo_handler() so we can't call spin_unlock_irq() or it will enable IRQs prematurely.

Fixes a3667aaed569 ("[SCSI] csiostor: Chelsio FCoE offload driver")
---
 drivers/scsi/csiostor/csio_lnode.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)
drivers/scsi/csiostor/csio_lnode.c +9 -6
index be5ee2d378155..957767d383610 100644
@@ -301,6 +301,7 @@ csio_ln_fdmi_rhba_cbfn(struct csio_hw *hw, struct csio_ioreq *fdmi_req)
 	struct fc_fdmi_port_name *port_name;
 	uint8_t buf[64];
 	uint8_t *fc4_type;
+	unsigned long flags;
 
 	if (fdmi_req->wr_status != FW_SUCCESS) {
 		csio_ln_dbg(ln, "WR error:%x in processing fdmi rhba cmd\n",
@@ -377,13 +378,13 @@ csio_ln_fdmi_rhba_cbfn(struct csio_hw *hw, struct csio_ioreq *fdmi_req)
 	len = (uint32_t)(pld - (uint8_t *)cmd);
 
 	/* Submit FDMI RPA request */
-	spin_lock_irq(&hw->lock);
+	spin_lock_irqsave(&hw->lock, flags);
 	if (csio_ln_mgmt_submit_req(fdmi_req, csio_ln_fdmi_done,
 				FCOE_CT, &fdmi_req->dma_buf, len)) {
 		CSIO_INC_STATS(ln, n_fdmi_err);
 		csio_ln_dbg(ln, "Failed to issue fdmi rpa req\n");
 	}
-	spin_unlock_irq(&hw->lock);
+	spin_unlock_irqrestore(&hw->lock, flags);
 }
 
 /*
@@ -404,6 +405,7 @@ csio_ln_fdmi_dprt_cbfn(struct csio_hw *hw, struct csio_ioreq *fdmi_req)
 	struct fc_fdmi_rpl *reg_pl;
 	struct fs_fdmi_attrs *attrib_blk;
 	uint8_t buf[64];
+	unsigned long flags;
 
 	if (fdmi_req->wr_status != FW_SUCCESS) {
 		csio_ln_dbg(ln, "WR error:%x in processing fdmi dprt cmd\n",
@@ -483,13 +485,13 @@ csio_ln_fdmi_dprt_cbfn(struct csio_hw *hw, struct csio_ioreq *fdmi_req)
 	attrib_blk->numattrs = htonl(numattrs);
 
 	/* Submit FDMI RHBA request */
-	spin_lock_irq(&hw->lock);
+	spin_lock_irqsave(&hw->lock, flags);
 	if (csio_ln_mgmt_submit_req(fdmi_req, csio_ln_fdmi_rhba_cbfn,
 				FCOE_CT, &fdmi_req->dma_buf, len)) {
 		CSIO_INC_STATS(ln, n_fdmi_err);
 		csio_ln_dbg(ln, "Failed to issue fdmi rhba req\n");
 	}
-	spin_unlock_irq(&hw->lock);
+	spin_unlock_irqrestore(&hw->lock, flags);
 }
 
 /*
@@ -504,6 +506,7 @@ csio_ln_fdmi_dhba_cbfn(struct csio_hw *hw, struct csio_ioreq *fdmi_req)
 	void *cmd;
 	struct fc_fdmi_port_name *port_name;
 	uint32_t len;
+	unsigned long flags;
 
 	if (fdmi_req->wr_status != FW_SUCCESS) {
 		csio_ln_dbg(ln, "WR error:%x in processing fdmi dhba cmd\n",
@@ -534,13 +537,13 @@ csio_ln_fdmi_dhba_cbfn(struct csio_hw *hw, struct csio_ioreq *fdmi_req)
 	len += sizeof(*port_name);
 
 	/* Submit FDMI request */
-	spin_lock_irq(&hw->lock);
+	spin_lock_irqsave(&hw->lock, flags);
 	if (csio_ln_mgmt_submit_req(fdmi_req, csio_ln_fdmi_dprt_cbfn,
 				FCOE_CT, &fdmi_req->dma_buf, len)) {
 		CSIO_INC_STATS(ln, n_fdmi_err);
 		csio_ln_dbg(ln, "Failed to issue fdmi dprt req\n");
 	}
-	spin_unlock_irq(&hw->lock);
+	spin_unlock_irqrestore(&hw->lock, flags);
 }
 
 /**
Signature · 1 line
2.20.1
author maintainer
#7 lore raw

PATCH 8/42 powerpc/pseries: Mark accumulate_stolen_time() as notrace

In reply to Sasha Levin

From: Michael Ellerman <[email protected]>

[ Upstream commit eb8e20f89093b64f48975c74ccb114e6775cee22 ]

accumulate_stolen_time() is called prior to interrupt state being reconciled, which can trip the warning in arch_local_irq_restore():

  WARNING: CPU: 5 PID: 1017 at arch/powerpc/kernel/irq.c:258 .arch_local_irq_restore+0x9c/0x130
  ...
  NIP .arch_local_irq_restore+0x9c/0x130
  LR  .rb_start_commit+0x38/0x80
  Call Trace:
    .ring_buffer_lock_reserve+0xe4/0x620
    .trace_function+0x44/0x210
    .function_trace_call+0x148/0x170
    .ftrace_ops_no_ops+0x180/0x1d0
    ftrace_call+0x4/0x8
    .accumulate_stolen_time+0x1c/0xb0
    decrementer_common+0x124/0x160

For now just mark it as notrace. We may change the ordering to call it after interrupt state has been reconciled, but that is a larger change.

---
 arch/powerpc/kernel/time.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/powerpc/kernel/time.c +1 -1
index ab7b661b6da3a..412ac5d45160b 100644
@@ -257,7 +257,7 @@ static u64 scan_dispatch_log(u64 stop_tb)
  * Accumulate stolen time by scanning the dispatch trace log.
  * Called on entry from user mode.
  */
-void accumulate_stolen_time(void)
+void notrace accumulate_stolen_time(void)
 {
 	u64 sst, ust;
 	u8 save_soft_enabled = local_paca->soft_enabled;
Signature · 1 line
2.20.1
author maintainer
#8 lore raw

PATCH 9/42 powerpc/pseries: Don't fail hash page table insert for bolted mapping

In reply to Sasha Levin

From: "Aneesh Kumar K.V" <[email protected]>

[ Upstream commit 75838a3290cd4ebbd1f567f310ba04b6ef017ce4 ]

If the hypervisor returned H_PTEG_FULL for H_ENTER hcall, retry a hash page table insert by removing a random entry from the group.

After some runtime, it is very well possible to find all the 8 hash page table entry slot in the hpte group used for mapping. Don't fail a bolted entry insert in that case. With Storage class memory a user can find this error easily since a namespace enable/disable is equivalent to memory add/remove.

This results in failures as reported below:

$ ndctl create-namespace -r region1 -t pmem -m devdax -a 65536 -s 100M
libndctl: ndctl_dax_enable: dax1.3: failed to enable
  Error: namespace1.2: failed to enable

failed to create namespace: No such device or address

In kernel log we find the details as below:

Unable to create mapping for hot added memory 0xc000042006000000..0xc00004200d000000: -1
dax_pmem: probe of dax1.3 failed with error -14

This indicates that we failed to create a bolted hash table entry for direct-map address backing the namespace.

We also observe failures such that not all namespaces will be enabled with ndctl enable-namespace all command.

---
 arch/powerpc/mm/hash_utils_64.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)
arch/powerpc/mm/hash_utils_64.c +8 -1
index bd666287c5eda..de1d8cdd29915 100644
@@ -289,7 +289,14 @@ int htab_bolt_mapping(unsigned long vstart, unsigned long vend,
 		ret = mmu_hash_ops.hpte_insert(hpteg, vpn, paddr, tprot,
 					       HPTE_V_BOLTED, psize, psize,
 					       ssize);
-
+		if (ret == -1) {
+			/* Try to remove a non bolted entry */
+			ret = mmu_hash_ops.hpte_remove(hpteg);
+			if (ret != -1)
+				ret = mmu_hash_ops.hpte_insert(hpteg, vpn, paddr, tprot,
+							       HPTE_V_BOLTED, psize, psize,
+							       ssize);
+		}
 		if (ret < 0)
 			break;
 
Signature · 1 line
2.20.1
author maintainer
#9 lore raw

PATCH 10/42 dma-debug: add a schedule point in debug_dma_dump_mappings()

In reply to Sasha Levin

From: Eric Dumazet <[email protected]>

[ Upstream commit 9ff6aa027dbb98755f0265695354f2dd07c0d1ce ]

debug_dma_dump_mappings() can take a lot of cpu cycles :

lpk43:/# time wc -l /sys/kernel/debug/dma-api/dump
163435 /sys/kernel/debug/dma-api/dump

real 0m0.463s
user 0m0.003s
sys 0m0.459s

Let's add a cond_resched() to avoid holding cpu for too long.

Cc Corentin Labbe <[email protected]>
Cc Christoph Hellwig <[email protected]>
Cc Marek Szyprowski <[email protected]>
---
 lib/dma-debug.c | 1 +
 1 file changed, 1 insertion(+)
lib/dma-debug.c +1 -0
index 8971370bfb161..4435bec55fb59 100644
@@ -435,6 +435,7 @@ void debug_dma_dump_mappings(struct device *dev)
 		}
 
 		spin_unlock_irqrestore(&bucket->lock, flags);
+		cond_resched();
 	}
 }
 EXPORT_SYMBOL(debug_dma_dump_mappings);
Signature · 1 line
2.20.1
author maintainer
#10 lore raw

PATCH 11/42 clocksource/drivers/asm9260: Add a check for of_clk_get

In reply to Sasha Levin

From: Chuhong Yuan <[email protected]>

[ Upstream commit 6e001f6a4cc73cd06fc7b8c633bc4906c33dd8ad ]

asm9260_timer_init misses a check for of_clk_get.
Add a check for it and print errors like other clocksource drivers.

---
 drivers/clocksource/asm9260_timer.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/clocksource/asm9260_timer.c +4 -0
index 1ba871b7fe118..e5717807c00a7 100644
@@ -198,6 +198,10 @@ static int __init asm9260_timer_init(struct device_node *np)
 	}
 
 	clk = of_clk_get(np, 0);
+	if (IS_ERR(clk)) {
+		pr_err("Failed to get clk!\n");
+		return PTR_ERR(clk);
+	}
 
 	ret = clk_prepare_enable(clk);
 	if (ret) {
Signature · 1 line
2.20.1
author maintainer
#11 lore raw

PATCH 12/42 powerpc/security/book3s64: Report L1TF status in sysfs

In reply to Sasha Levin

From: Anthony Steinhauser <[email protected]>

[ Upstream commit 8e6b6da91ac9b9ec5a925b6cb13f287a54bd547d ]

Some PowerPC CPUs are vulnerable to L1TF to the same extent as to Meltdown. It is also mitigated by flushing the L1D on privilege transition.

Currently the sysfs gives a false negative on L1TF on CPUs that I verified to be vulnerable, a Power9 Talos II Boston 004e 1202, PowerNV T2P9D01.

[mpe: Just have cpu_show_l1tf() call cpu_show_meltdown() directly]
---
 arch/powerpc/kernel/security.c | 5 +++++
 1 file changed, 5 insertions(+)
arch/powerpc/kernel/security.c +5 -0
index 11fff9669cfdf..db66f25c190c9 100644
@@ -161,6 +161,11 @@ ssize_t cpu_show_meltdown(struct device *dev, struct device_attribute *attr, cha
 
 	return sprintf(buf, "Vulnerable\n");
 }
+
+ssize_t cpu_show_l1tf(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	return cpu_show_meltdown(dev, attr, buf);
+}
 #endif
 
 ssize_t cpu_show_spectre_v1(struct device *dev, struct device_attribute *attr, char *buf)
Signature · 1 line
2.20.1
author maintainer
#12 lore raw

PATCH 13/42 powerpc/book3s64/hash: Add cond_resched to avoid soft lockup warning

In reply to Sasha Levin

From: "Aneesh Kumar K.V" <[email protected]>

[ Upstream commit 16f6b67cf03cb43db7104acb2ca877bdc2606c92 ]

With large memory (8TB and more) hotplug, we can get soft lockup warnings as below. These were caused by a long loop without any explicit cond_resched which is a problem for !PREEMPT kernels.

Avoid this using cond_resched() while inserting hash page table entries. We already do similar cond_resched() in __add_pages(), see commit f64ac5e6e306 ("mm, memory_hotplug: add scheduling point to __add_pages").

rcu: 3-....: (24002 ticks this GP) idle=13e/1/0x4000000000000002 softirq=722/722 fqs=12001
(t=24003 jiffies g=4285 q=2002)
NMI backtrace for cpu 3

  CPU: 3 PID: 3870 Comm: ndctl Not tainted 5.3.0-197.18-default+ #2
  Call Trace:
    dump_stack+0xb0/0xf4 (unreliable)
    nmi_cpu_backtrace+0x124/0x130
    nmi_trigger_cpumask_backtrace+0x1ac/0x1f0
    arch_trigger_cpumask_backtrace+0x28/0x3c
    rcu_dump_cpu_stacks+0xf8/0x154
    rcu_sched_clock_irq+0x878/0xb40
    update_process_times+0x48/0x90
    tick_sched_handle.isra.16+0x4c/0x80
    tick_sched_timer+0x68/0xe0
    __hrtimer_run_queues+0x180/0x430
    hrtimer_interrupt+0x110/0x300
    timer_interrupt+0x108/0x2f0
    decrementer_common+0x114/0x120
  --- interrupt: 901 at arch_add_memory+0xc0/0x130
      LR = arch_add_memory+0x74/0x130
    memremap_pages+0x494/0x650
    devm_memremap_pages+0x3c/0xa0
    pmem_attach_disk+0x188/0x750
    nvdimm_bus_probe+0xac/0x2c0
    really_probe+0x148/0x570
    driver_probe_device+0x19c/0x1d0
    device_driver_attach+0xcc/0x100
    bind_store+0x134/0x1c0
    drv_attr_store+0x44/0x60
    sysfs_kf_write+0x64/0x90
    kernfs_fop_write+0x1a0/0x270
    __vfs_write+0x3c/0x70
    vfs_write+0xd0/0x260
    ksys_write+0xdc/0x130
    system_call+0x5c/0x68
---
 arch/powerpc/mm/hash_utils_64.c | 1 +
 1 file changed, 1 insertion(+)
arch/powerpc/mm/hash_utils_64.c +1 -0
index de1d8cdd29915..2dc1fc445f357 100644
@@ -300,6 +300,7 @@ int htab_bolt_mapping(unsigned long vstart, unsigned long vend,
 		if (ret < 0)
 			break;
 
+		cond_resched();
 #ifdef CONFIG_DEBUG_PAGEALLOC
 		if (debug_pagealloc_enabled() &&
 			(paddr >> PAGE_SHIFT) < linear_map_hash_count)
Signature · 1 line
2.20.1
author maintainer
#13 lore raw

PATCH 14/42 jbd2: Fix statistics for the number of logged blocks

In reply to Sasha Levin

From: Jan Kara <[email protected]>

[ Upstream commit 015c6033068208d6227612c878877919f3fcf6b6 ]

jbd2 statistics counting number of blocks logged in a transaction was wrong. It didn't count the commit block and more importantly it didn't count revoke descriptor blocks. Make sure these get properly counted.

---
 fs/jbd2/commit.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
fs/jbd2/commit.c +3 -1
index 10ec276761913..d002b2b6895fe 100644
@@ -722,7 +722,6 @@ start_journal_io:
 				submit_bh(REQ_OP_WRITE, WRITE_SYNC, bh);
 			}
 			cond_resched();
-			stats.run.rs_blocks_logged += bufs;
 
 			/* Force a new descriptor to be generated next
                            time round the loop. */
@@ -809,6 +808,7 @@ start_journal_io:
 		if (unlikely(!buffer_uptodate(bh)))
 			err = -EIO;
 		jbd2_unfile_log_bh(bh);
+		stats.run.rs_blocks_logged++;
 
 		/*
 		 * The list contains temporary buffer heads created by
@@ -854,6 +854,7 @@ start_journal_io:
 		BUFFER_TRACE(bh, "ph5: control buffer writeout done: unfile");
 		clear_buffer_jwrite(bh);
 		jbd2_unfile_log_bh(bh);
+		stats.run.rs_blocks_logged++;
 		__brelse(bh);		/* One for getblk */
 		/* AKPM: bforget here */
 	}
@@ -875,6 +876,7 @@ start_journal_io:
 	}
 	if (cbh)
 		err = journal_wait_on_commit_record(journal, cbh);
+	stats.run.rs_blocks_logged++;
 	if (jbd2_has_feature_async_commit(journal) &&
 	    journal->j_flags & JBD2_BARRIER) {
 		blkdev_issue_flush(journal->j_dev, GFP_NOFS, NULL);
Signature · 1 line
2.20.1
author maintainer
#14 lore raw

PATCH 15/42 scsi: tracing: Fix handling of TRANSFER LENGTH == 0 for READ(6) and WRITE(6)

In reply to Sasha Levin

From: Bart Van Assche <[email protected]>

[ Upstream commit f6b8540f40201bff91062dd64db8e29e4ddaaa9d ]

According to SBC-2 a TRANSFER LENGTH field of zero means that 256 logical blocks must be transferred. Make the SCSI tracing code follow SBC-2.

Fixes bf8162354233 ("[SCSI] add scsi trace core functions and put trace points")
Cc Christoph Hellwig <[email protected]>
Cc Hannes Reinecke <[email protected]>
Cc Douglas Gilbert <[email protected]>
---
 drivers/scsi/scsi_trace.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)
drivers/scsi/scsi_trace.c +7 -4
index 0ff083bbf5b1f..617a607375908 100644
@@ -30,15 +30,18 @@ static const char *
 scsi_trace_rw6(struct trace_seq *p, unsigned char *cdb, int len)
 {
 	const char *ret = trace_seq_buffer_ptr(p);
-	sector_t lba = 0, txlen = 0;
+	u32 lba = 0, txlen;
 
 	lba |= ((cdb[1] & 0x1F) << 16);
 	lba |=  (cdb[2] << 8);
 	lba |=   cdb[3];
-	txlen = cdb[4];
+	/*
+	 * From SBC-2: a TRANSFER LENGTH field set to zero specifies that 256
+	 * logical blocks shall be read (READ(6)) or written (WRITE(6)).
+	 */
+	txlen = cdb[4] ? cdb[4] : 256;
 
-	trace_seq_printf(p, "lba=%llu txlen=%llu",
-			 (unsigned long long)lba, (unsigned long long)txlen);
+	trace_seq_printf(p, "lba=%u txlen=%u", lba, txlen);
 	trace_seq_putc(p, 0);
 
 	return ret;
Signature · 1 line
2.20.1
author maintainer
#15 lore raw

PATCH 16/42 scsi: lpfc: Fix duplicate unreg_rpi error in port offline flow

In reply to Sasha Levin

From: James Smart <[email protected]>

[ Upstream commit 7cfd5639d99bec0d27af089d0c8c114330e43a72 ]

If the driver receives a login that is later then LOGO'd by the remote port (aka ndlp), the driver, upon the completion of the LOGO ACC transmission, will logout the node and unregister the rpi that is being used for the node. As part of the unreg, the node's rpi value is replaced by the LPFC_RPI_ALLOC_ERROR value. If the port is subsequently offlined, the offline walks the nodes and ensures they are logged out, which possibly entails unreg'ing their rpi values. This path does not validate the node's rpi value, thus doesn't detect that it has been unreg'd already. The replaced rpi value is then used when accessing the rpi bitmask array which tracks active rpi values. As the LPFC_RPI_ALLOC_ERROR value is not a valid index for the bitmask, it may fault the system.

Revise the rpi release code to detect when the rpi value is the replaced RPI_ALLOC_ERROR value and ignore further release steps.

---
 drivers/scsi/lpfc/lpfc_sli.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/scsi/lpfc/lpfc_sli.c +7 -0
index 1eb9d5f6cea05..cbe808e83f477 100644
@@ -15995,6 +15995,13 @@ lpfc_sli4_alloc_rpi(struct lpfc_hba *phba)
 static void
 __lpfc_sli4_free_rpi(struct lpfc_hba *phba, int rpi)
 {
+	/*
+	 * if the rpi value indicates a prior unreg has already
+	 * been done, skip the unreg.
+	 */
+	if (rpi == LPFC_RPI_ALLOC_ERROR)
+		return;
+
 	if (test_and_clear_bit(rpi, phba->sli4_hba.rpi_bmask)) {
 		phba->sli4_hba.rpi_count--;
 		phba->sli4_hba.max_cfg_param.rpi_used--;
Signature · 1 line
2.20.1
author maintainer
#16 lore raw

PATCH 17/42 clk: qcom: Allow constant ratio freq tables for rcg

In reply to Sasha Levin

From: Jeffrey Hugo <[email protected]>

[ Upstream commit efd164b5520afd6fb2883b68e0d408a7de29c491 ]

Some RCGs (the gfx_3d_src_clk in msm8998 for example) are basically just some constant ratio from the input across the entire frequency range. It would be great if we could specify the frequency table as a single entry constant ratio instead of a long list, ie:

	{ .src = P_GPUPLL0_OUT_EVEN, .pre_div = 3 },
        { }

So, lets support that.

We need to fix a corner case in qcom_find_freq() where if the freq table is non-null, but has no frequencies, we end up returning an "entry" before the table array, which is bad. Then, we need ignore the freq from the table, and instead base everything on the requested freq.

---
 drivers/clk/qcom/clk-rcg2.c | 2 ++
 drivers/clk/qcom/common.c   | 3 +++
 2 files changed, 5 insertions(+)
drivers/clk/qcom/clk-rcg2.c +2 -0
index a071bba8018c4..0ae1b0a66eb55 100644
@@ -196,6 +196,8 @@ static int _freq_tbl_determine_rate(struct clk_hw *hw,
 	p = clk_hw_get_parent_by_index(hw, index);
 	if (clk_flags & CLK_SET_RATE_PARENT) {
 		if (f->pre_div) {
+			if (!rate)
+				rate = req->rate;
 			rate /= 2;
 			rate *= f->pre_div + 1;
 		}
drivers/clk/qcom/common.c +3 -0
index fffcbaf0fba74..f89a9f0aa606e 100644
@@ -37,6 +37,9 @@ struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, unsigned long rate)
 	if (!f)
 		return NULL;
 
+	if (!f->freq)
+		return f;
+
 	for (; f->freq; f++)
 		if (rate <= f->freq)
 			return f;
Signature · 1 line
2.20.1
author maintainer
#17 lore raw

PATCH 18/42 irqchip/irq-bcm7038-l1: Enable parent IRQ if necessary

In reply to Sasha Levin

From: Florian Fainelli <[email protected]>

[ Upstream commit 27eebb60357ed5aa6659442f92907c0f7368d6ae ]

If the 'brcm,irq-can-wake' property is specified, make sure we also enable the corresponding parent interrupt we are attached to.

---
 drivers/irqchip/irq-bcm7038-l1.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/irqchip/irq-bcm7038-l1.c +4 -0
index 6e24facebb46d..a571d9c6e42ae 100644
@@ -282,6 +282,10 @@ static int __init bcm7038_l1_init_one(struct device_node *dn,
 		pr_err("failed to map parent interrupt %d\n", parent_irq);
 		return -EINVAL;
 	}
+
+	if (of_property_read_bool(dn, "brcm,irq-can-wake"))
+		enable_irq_wake(parent_irq);
+
 	irq_set_chained_handler_and_data(parent_irq, bcm7038_l1_irq_handle,
 					 intc);
 
Signature · 1 line
2.20.1
author maintainer
#18 lore raw

PATCH 19/42 irqchip: ingenic: Error out if IRQ domain creation failed

In reply to Sasha Levin

From: Paul Cercueil <[email protected]>

[ Upstream commit 52ecc87642f273a599c9913b29fd179c13de457b ]

If we cannot create the IRQ domain, the driver should fail to probe instead of succeeding with just a warning message.

---
 drivers/irqchip/irq-ingenic.c | 15 ++++++++++-----
 1 file changed, 10 insertions(+), 5 deletions(-)
drivers/irqchip/irq-ingenic.c +10 -5
index fc5953dea509a..b2e16dca76a60 100644
@@ -117,6 +117,14 @@ static int __init ingenic_intc_of_init(struct device_node *node,
 		goto out_unmap_irq;
 	}
 
+	domain = irq_domain_add_legacy(node, num_chips * 32,
+				       JZ4740_IRQ_BASE, 0,
+				       &irq_domain_simple_ops, NULL);
+	if (!domain) {
+		err = -ENOMEM;
+		goto out_unmap_base;
+	}
+
 	for (i = 0; i < num_chips; i++) {
 		/* Mask all irqs */
 		writel(0xffffffff, intc->base + (i * CHIP_SIZE) +
@@ -143,14 +151,11 @@ static int __init ingenic_intc_of_init(struct device_node *node,
 				       IRQ_NOPROBE | IRQ_LEVEL);
 	}
 
-	domain = irq_domain_add_legacy(node, num_chips * 32, JZ4740_IRQ_BASE, 0,
-				       &irq_domain_simple_ops, NULL);
-	if (!domain)
-		pr_warn("unable to register IRQ domain\n");
-
 	setup_irq(parent_irq, &intc_cascade_action);
 	return 0;
 
+out_unmap_base:
+	iounmap(intc->base);
 out_unmap_irq:
 	irq_dispose_mapping(parent_irq);
 out_free:
Signature · 1 line
2.20.1
author maintainer
#19 lore raw

PATCH 20/42 mfd: mfd-core: Honour Device Tree's request to disable a child-device

In reply to Sasha Levin

From: Lee Jones <[email protected]>

[ Upstream commit 6b5c350648b857047b47acf74a57087ad27d6183 ]

Until now, MFD has assumed all child devices passed to it (via mfd_cells) are to be registered. It does not take into account requests from Device Tree and the like to disable child devices on a per-platform basis.

Well now it does.

---
 drivers/mfd/mfd-core.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/mfd/mfd-core.c +5 -0
index 5c8ed2150c8bf..fae7bfe7a21a1 100644
@@ -178,6 +178,11 @@ static int mfd_add_device(struct device *parent, int id,
 	if (parent->of_node && cell->of_compatible) {
 		for_each_child_of_node(parent->of_node, np) {
 			if (of_device_is_compatible(np, cell->of_compatible)) {
+				if (!of_device_is_available(np)) {
+					/* Ignore disabled devices error free */
+					ret = 0;
+					goto fail_alias;
+				}
 				pdev->dev.of_node = np;
 				pdev->dev.fwnode = &np->fwnode;
 				break;
Signature · 1 line
2.20.1
author maintainer
#20 lore raw

PATCH 21/42 fs/quota: handle overflows of sysctl fs.quota.* and report as unsigned long

In reply to Sasha Levin

From: Konstantin Khlebnikov <[email protected]>

[ Upstream commit 6fcbcec9cfc7b3c6a2c1f1a23ebacedff7073e0a ]

Quota statistics counted as 64-bit per-cpu counter. Reading sums per-cpu fractions as signed 64-bit int, filters negative values and then reports lower half as signed 32-bit int.

Result may looks like:

fs.quota.allocated_dquots = 22327
fs.quota.cache_hits = -489852115
fs.quota.drops = -487288718
fs.quota.free_dquots = 22083
fs.quota.lookups = -486883485
fs.quota.reads = 22327
fs.quota.syncs = 335064
fs.quota.writes = 3088689

Values bigger than 2^31-1 reported as negative.

All counters except "allocated_dquots" and "free_dquots" are monotonic, thus they should be reported as is without filtering negative values.

Kernel doesn't have generic helper for 64-bit sysctl yet, let's use at least unsigned long.

---
 fs/quota/dquot.c      | 29 +++++++++++++++++------------
 include/linux/quota.h |  2 +-
 2 files changed, 18 insertions(+), 13 deletions(-)
fs/quota/dquot.c +17 -12
index f9246ac4eef81..b09f7876f4467 100644
@@ -2848,68 +2848,73 @@ EXPORT_SYMBOL(dquot_quotactl_sysfile_ops);
 static int do_proc_dqstats(struct ctl_table *table, int write,
 		     void __user *buffer, size_t *lenp, loff_t *ppos)
 {
-	unsigned int type = (int *)table->data - dqstats.stat;
+	unsigned int type = (unsigned long *)table->data - dqstats.stat;
+	s64 value = percpu_counter_sum(&dqstats.counter[type]);
+
+	/* Filter negative values for non-monotonic counters */
+	if (value < 0 && (type == DQST_ALLOC_DQUOTS ||
+			  type == DQST_FREE_DQUOTS))
+		value = 0;
 
 	/* Update global table */
-	dqstats.stat[type] =
-			percpu_counter_sum_positive(&dqstats.counter[type]);
-	return proc_dointvec(table, write, buffer, lenp, ppos);
+	dqstats.stat[type] = value;
+	return proc_doulongvec_minmax(table, write, buffer, lenp, ppos);
 }
 
 static struct ctl_table fs_dqstats_table[] = {
 	{
 		.procname	= "lookups",
 		.data		= &dqstats.stat[DQST_LOOKUPS],
-		.maxlen		= sizeof(int),
+		.maxlen		= sizeof(unsigned long),
 		.mode		= 0444,
 		.proc_handler	= do_proc_dqstats,
 	},
 	{
 		.procname	= "drops",
 		.data		= &dqstats.stat[DQST_DROPS],
-		.maxlen		= sizeof(int),
+		.maxlen		= sizeof(unsigned long),
 		.mode		= 0444,
 		.proc_handler	= do_proc_dqstats,
 	},
 	{
 		.procname	= "reads",
 		.data		= &dqstats.stat[DQST_READS],
-		.maxlen		= sizeof(int),
+		.maxlen		= sizeof(unsigned long),
 		.mode		= 0444,
 		.proc_handler	= do_proc_dqstats,
 	},
 	{
 		.procname	= "writes",
 		.data		= &dqstats.stat[DQST_WRITES],
-		.maxlen		= sizeof(int),
+		.maxlen		= sizeof(unsigned long),
 		.mode		= 0444,
 		.proc_handler	= do_proc_dqstats,
 	},
 	{
 		.procname	= "cache_hits",
 		.data		= &dqstats.stat[DQST_CACHE_HITS],
-		.maxlen		= sizeof(int),
+		.maxlen		= sizeof(unsigned long),
 		.mode		= 0444,
 		.proc_handler	= do_proc_dqstats,
 	},
 	{
 		.procname	= "allocated_dquots",
 		.data		= &dqstats.stat[DQST_ALLOC_DQUOTS],
-		.maxlen		= sizeof(int),
+		.maxlen		= sizeof(unsigned long),
 		.mode		= 0444,
 		.proc_handler	= do_proc_dqstats,
 	},
 	{
 		.procname	= "free_dquots",
 		.data		= &dqstats.stat[DQST_FREE_DQUOTS],
-		.maxlen		= sizeof(int),
+		.maxlen		= sizeof(unsigned long),
 		.mode		= 0444,
 		.proc_handler	= do_proc_dqstats,
 	},
 	{
 		.procname	= "syncs",
 		.data		= &dqstats.stat[DQST_SYNCS],
-		.maxlen		= sizeof(int),
+		.maxlen		= sizeof(unsigned long),
 		.mode		= 0444,
 		.proc_handler	= do_proc_dqstats,
 	},
include/linux/quota.h +1 -1
index 55107a8ff8877..23eb8ea07def3 100644
@@ -263,7 +263,7 @@ enum {
 };
 
 struct dqstats {
-	int stat[_DQST_DQSTAT_LAST];
+	unsigned long stat[_DQST_DQSTAT_LAST];
 	struct percpu_counter counter[_DQST_DQSTAT_LAST];
 };
 
Signature · 1 line
2.20.1
author maintainer
#21 lore raw

PATCH 22/42 scsi: lpfc: fix: Coverity: lpfc_cmpl_els_rsp(): Null pointer dereferences

In reply to Sasha Levin

From: James Smart <[email protected]>

[ Upstream commit 6c6d59e0fe5b86cf273d6d744a6a9768c4ecc756 ]

Coverity reported the following:

*** CID 101747: Null pointer dereferences (FORWARD_NULL) /drivers/scsi/lpfc/lpfc_els.c: 4439 in lpfc_cmpl_els_rsp()

4433     			kfree(mp);
4434     		}
4435     		mempool_free(mbox, phba->mbox_mem_pool);
4436     	}
4437     out:
4438     	if (ndlp && NLP_CHK_NODE_ACT(ndlp)) {
vvv     CID 101747:  Null pointer dereferences  (FORWARD_NULL)
vvv     Dereferencing null pointer "shost".
4439     		spin_lock_irq(shost->host_lock);
4440     		ndlp->nlp_flag &= ~(NLP_ACC_REGLOGIN | NLP_RM_DFLT_RPI);
4441     		spin_unlock_irq(shost->host_lock);

4442
4443 /* If the node is not being used by another discovery thread,
4444 * and we are sending a reject, we are done with it.

Fix by adding a check for non-null shost in line 4438. The scenario when shost is set to null is when ndlp is null. As such, the ndlp check present was sufficient. But better safe than sorry so add the shost check.

Addresses-Coverity-ID: 101747 ("Null pointer dereferences")

Fixes 2e0fef85e098 ("[SCSI] lpfc: NPIV: split ports")
---
 drivers/scsi/lpfc/lpfc_els.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/scsi/lpfc/lpfc_els.c +1 -1
index 3702497b5b169..4901bf24916b5 100644
@@ -3863,7 +3863,7 @@ lpfc_cmpl_els_rsp(struct lpfc_hba *phba, struct lpfc_iocbq *cmdiocb,
 		mempool_free(mbox, phba->mbox_mem_pool);
 	}
 out:
-	if (ndlp && NLP_CHK_NODE_ACT(ndlp)) {
+	if (ndlp && NLP_CHK_NODE_ACT(ndlp) && shost) {
 		spin_lock_irq(shost->host_lock);
 		ndlp->nlp_flag &= ~(NLP_ACC_REGLOGIN | NLP_RM_DFLT_RPI);
 		spin_unlock_irq(shost->host_lock);
Signature · 1 line
2.20.1
author maintainer
#22 lore raw

PATCH 23/42 scsi: ufs: fix potential bug which ends in system hang

In reply to Sasha Levin

From: Bean Huo <[email protected]>

[ Upstream commit cfcbae3895b86c390ede57b2a8f601dd5972b47b ]

In function __ufshcd_query_descriptor(), in the event of an error happening, we directly goto out_unlock and forget to invaliate hba->dev_cmd.query.descriptor pointer. This results in this pointer still valid in ufshcd_copy_query_response() for other query requests which go through ufshcd_exec_raw_upiu_cmd(). This will cause __memcpy() crash and system hangs. Log as shown below:

Unable to handle kernel paging request at virtual address

ffff000012233c40
Mem abort info:
ESR = 0x96000047
Exception class = DABT (current EL), IL = 32 bits SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000047
CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp = 0000000028cc735c [ffff000012233c40] pgd=00000000bffff003, pud=00000000bfffe003, pmd=00000000ba8b8003, pte=0000000000000000

 Internal error: Oops: 96000047 [#2] PREEMPT SMP
 ...
 Call trace:
  __memcpy+0x74/0x180
  ufshcd_issue_devman_upiu_cmd+0x250/0x3c0
  ufshcd_exec_raw_upiu_cmd+0xfc/0x1a8
  ufs_bsg_request+0x178/0x3b0
  bsg_queue_rq+0xc0/0x118
  blk_mq_dispatch_rq_list+0xb0/0x538
  blk_mq_sched_dispatch_requests+0x18c/0x1d8
  __blk_mq_run_hw_queue+0xb4/0x118
  blk_mq_run_work_fn+0x28/0x38
  process_one_work+0x1ec/0x470
  worker_thread+0x48/0x458
  kthread+0x130/0x138
  ret_from_fork+0x10/0x1c
 Code: 540000ab a8c12027 a88120c7 a8c12027 (a88120c7)
 ---[ end trace 793e1eb5dff69f2d ]---
 note: kworker/0:2H[2054] exited with preempt_count 1

This patch is to move "descriptor = NULL" down to below the label "out_unlock".

---
 drivers/scsi/ufs/ufshcd.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/scsi/ufs/ufshcd.c +1 -1
index 26f259fb6e3ca..094e879af1213 100644
@@ -2006,10 +2006,10 @@ static int __ufshcd_query_descriptor(struct ufs_hba *hba,
 		goto out_unlock;
 	}
 
-	hba->dev_cmd.query.descriptor = NULL;
 	*buf_len = be16_to_cpu(response->upiu_res.length);
 
 out_unlock:
+	hba->dev_cmd.query.descriptor = NULL;
 	mutex_unlock(&hba->dev_cmd.lock);
 out:
 	ufshcd_release(hba);
Signature · 1 line
2.20.1
author maintainer
#23 lore raw

PATCH 24/42 powerpc/pseries/cmm: Implement release() function for sysfs device

In reply to Sasha Levin

From: David Hildenbrand <[email protected]>

[ Upstream commit 7d8212747435c534c8d564fbef4541a463c976ff ]

When unloading the module, one gets

  ------------[ cut here ]------------
  Device 'cmm0' does not have a release() function, it is broken and must be fixed. See Documentation/kobject.txt.
  WARNING: CPU: 0 PID: 19308 at drivers/base/core.c:1244 .device_release+0xcc/0xf0
  ...

We only have one static fake device. There is nothing to do when releasing the device (via cmm_exit()).

---
 arch/powerpc/platforms/pseries/cmm.c | 5 +++++
 1 file changed, 5 insertions(+)
arch/powerpc/platforms/pseries/cmm.c +5 -0
index 66e7227469b8c..b5ff5ee3e39cb 100644
@@ -391,6 +391,10 @@ static struct bus_type cmm_subsys = {
 	.dev_name = "cmm",
 };
 
+static void cmm_release_device(struct device *dev)
+{
+}
+
 /**
  * cmm_sysfs_register - Register with sysfs
  *
@@ -406,6 +410,7 @@ static int cmm_sysfs_register(struct device *dev)
 
 	dev->id = 0;
 	dev->bus = &cmm_subsys;
+	dev->release = cmm_release_device;
 
 	if ((rc = device_register(dev)))
 		goto subsys_unregister;
Signature · 1 line
2.20.1
author maintainer
#24 lore raw

PATCH 25/42 powerpc/security: Fix wrong message when RFI Flush is disable

In reply to Sasha Levin

From: "Gustavo L. F. Walbon" <[email protected]>

[ Upstream commit 4e706af3cd8e1d0503c25332b30cad33c97ed442 ]

The issue was showing "Mitigation" message via sysfs whatever the state of "RFI Flush", but it should show "Vulnerable" when it is disabled.

If you have "L1D private" feature enabled and not "RFI Flush" you are vulnerable to meltdown attacks.

"RFI Flush" is the key feature to mitigate the meltdown whatever the "L1D private" state.

SEC_FTR_L1D_THREAD_PRIV is a feature for Power9 only.

So the message should be as the truth table shows:

  CPU | L1D private | RFI Flush |                sysfs
  ----|-------------|-----------|-------------------------------------
   P9 |    False    |   False   | Vulnerable
   P9 |    False    |   True    | Mitigation: RFI Flush
   P9 |    True     |   False   | Vulnerable: L1D private per thread
   P9 |    True     |   True    | Mitigation: RFI Flush, L1D private per thread
   P8 |    False    |   False   | Vulnerable
   P8 |    False    |   True    | Mitigation: RFI Flush

Output before this fix:

  # cat /sys/devices/system/cpu/vulnerabilities/meltdown
  Mitigation: RFI Flush, L1D private per thread
  # echo 0 > /sys/kernel/debug/powerpc/rfi_flush
  # cat /sys/devices/system/cpu/vulnerabilities/meltdown
  Mitigation: L1D private per thread

Output after fix:

  # cat /sys/devices/system/cpu/vulnerabilities/meltdown
  Mitigation: RFI Flush, L1D private per thread
  # echo 0 > /sys/kernel/debug/powerpc/rfi_flush
  # cat /sys/devices/system/cpu/vulnerabilities/meltdown
  Vulnerable: L1D private per thread
---
 arch/powerpc/kernel/security.c | 16 ++++++----------
 1 file changed, 6 insertions(+), 10 deletions(-)
arch/powerpc/kernel/security.c +6 -10
index db66f25c190c9..ff85fc8001836 100644
@@ -135,26 +135,22 @@ ssize_t cpu_show_meltdown(struct device *dev, struct device_attribute *attr, cha
 
 	thread_priv = security_ftr_enabled(SEC_FTR_L1D_THREAD_PRIV);
 
-	if (rfi_flush || thread_priv) {
+	if (rfi_flush) {
 		struct seq_buf s;
 		seq_buf_init(&s, buf, PAGE_SIZE - 1);
 
-		seq_buf_printf(&s, "Mitigation: ");
-
-		if (rfi_flush)
-			seq_buf_printf(&s, "RFI Flush");
-
-		if (rfi_flush && thread_priv)
-			seq_buf_printf(&s, ", ");
-
+		seq_buf_printf(&s, "Mitigation: RFI Flush");
 		if (thread_priv)
-			seq_buf_printf(&s, "L1D private per thread");
+			seq_buf_printf(&s, ", L1D private per thread");
 
 		seq_buf_printf(&s, "\n");
 
 		return s.len;
 	}
 
+	if (thread_priv)
+		return sprintf(buf, "Vulnerable: L1D private per thread\n");
+
 	if (!security_ftr_enabled(SEC_FTR_L1D_FLUSH_HV) &&
 	    !security_ftr_enabled(SEC_FTR_L1D_FLUSH_PR))
 		return sprintf(buf, "Not affected\n");
Signature · 1 line
2.20.1
author maintainer
#25 lore raw

PATCH 26/42 scsi: atari_scsi: sun3_scsi: Set sg_tablesize to 1 instead of SG_NONE

In reply to Sasha Levin

From: Finn Thain <[email protected]>

[ Upstream commit 79172ab20bfd8437b277254028efdb68484e2c21 ]

Since the scsi subsystem adopted the blk-mq API, a host with zero sg_tablesize crashes with a NULL pointer dereference.

blk_queue_max_segments: set to minimum 1
scsi 0:0:0:0: Direct-Access QEMU QEMU HARDDISK 2.5+ PQ: 0 ANSI: 5
scsi target0:0:0: Beginning Domain Validation
scsi target0:0:0: Domain Validation skipping write tests
scsi target0:0:0: Ending Domain Validation
blk_queue_max_segments: set to minimum 1
scsi 0:0:1:0: Direct-Access QEMU QEMU HARDDISK 2.5+ PQ: 0 ANSI: 5
scsi target0:0:1: Beginning Domain Validation
scsi target0:0:1: Domain Validation skipping write tests
scsi target0:0:1: Ending Domain Validation
blk_queue_max_segments: set to minimum 1
scsi 0:0:2:0: CD-ROM QEMU QEMU CD-ROM 2.5+ PQ: 0 ANSI: 5
scsi target0:0:2: Beginning Domain Validation
scsi target0:0:2: Domain Validation skipping write tests
scsi target0:0:2: Ending Domain Validation
blk_queue_max_segments: set to minimum 1
blk_queue_max_segments: set to minimum 1
blk_queue_max_segments: set to minimum 1
blk_queue_max_segments: set to minimum 1
sr 0:0:2:0: Power-on or device reset occurred
sd 0:0:0:0: Power-on or device reset occurred
sd 0:0:1:0: Power-on or device reset occurred
sd 0:0:0:0: [sda] 10485762 512-byte logical blocks: (5.37 GB/5.00 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

Unable to handle kernel NULL pointer dereference at virtual address (ptrval)
Oops: 00000000
Modules linked in:
PC: [<001cd874>] blk_mq_free_request+0x66/0xe2
SR: 2004  SP: (ptrval)  a2: 00874520
d0: 00000000    d1: 00000000    d2: 009ba800    d3: 00000000
d4: 00000000    d5: 08000002    a0: 0087be68    a1: 009a81e0

Process kworker/u2:2 (pid: 15, task=(ptrval)) Frame format=7 eff addr=0000007a ssw=0505 faddr=0000007a wb 1 stat/addr/data: 0000 00000000 00000000
wb 2 stat/addr/data: 0000 00000000 00000000
wb 3 stat/addr/data: 0000 0000007a 00000000 push data: 00000000 00000000 00000000 00000000 Stack from 0087bd98:

        00000002 00000000 0087be72 009a7820 0087bdb4 001c4f6c 009a7820 0087bdd4
        0024d200 009a7820 0024d0dc 0087be72 009baa00 0087be68 009a5000 0087be7c
        00265d10 009a5000 0087be72 00000003 00000000 00000000 00000000 0087be68
        00000bb8 00000005 00000000 00000000 00000000 00000000 00265c56 00000000
        009ba60c 0036ddf4 00000002 ffffffff 009baa00 009ba600 009a50d6 0087be74
        00227ba0 009baa08 00000001 009baa08 009ba60c 0036ddf4 00000000 00000000
Call Trace: [<001c4f6c>] blk_put_request+0xe/0x14
 [<0024d200>] __scsi_execute+0x124/0x174
 [<0024d0dc>] __scsi_execute+0x0/0x174
 [<00265d10>] sd_revalidate_disk+0xba/0x1f02
 [<00265c56>] sd_revalidate_disk+0x0/0x1f02
 [<0036ddf4>] strlen+0x0/0x22
 [<00227ba0>] device_add+0x3da/0x604
 [<0036ddf4>] strlen+0x0/0x22
 [<00267e64>] sd_probe+0x30c/0x4b4
 [<0002da44>] process_one_work+0x0/0x402
 [<0022b978>] really_probe+0x226/0x354
 [<0022bc34>] driver_probe_device+0xa4/0xf0
 [<0002da44>] process_one_work+0x0/0x402
 [<0022bcd0>] __driver_attach_async_helper+0x50/0x70
 [<00035dae>] async_run_entry_fn+0x36/0x130
 [<0002db88>] process_one_work+0x144/0x402
 [<0002e1aa>] worker_thread+0x0/0x570
 [<0002e29a>] worker_thread+0xf0/0x570
 [<0002e1aa>] worker_thread+0x0/0x570
 [<003768d8>] schedule+0x0/0xb8
 [<0003f58c>] __init_waitqueue_head+0x0/0x12
 [<00033e92>] kthread+0xc2/0xf6
 [<000331e8>] kthread_parkme+0x0/0x4e
 [<003768d8>] schedule+0x0/0xb8
 [<00033dd0>] kthread+0x0/0xf6
 [<00002c10>] ret_from_kernel_thread+0xc/0x14
Code: 0280 0006 0800 56c0 4400 0280 0000 00ff <52b4> 0c3a 082b 0006 0013 6706 2042 53a8 00c4 4ab9 0047 3374 6640 202d 000c 670c

Disabling lock debugging due to kernel taint

Avoid this by setting sg_tablesize = 1.

References: commit 68ab2d76e4be ("scsi: cxlflash: Set sg_tablesize to 1 instead of SG_NONE")

---
 drivers/scsi/atari_scsi.c | 6 +++---
 drivers/scsi/mac_scsi.c   | 2 +-
 drivers/scsi/sun3_scsi.c  | 4 ++--
 3 files changed, 6 insertions(+), 6 deletions(-)
drivers/scsi/atari_scsi.c +3 -3
index a59ad94ea52b3..9dc4b689f94b0 100644
@@ -753,7 +753,7 @@ static int __init atari_scsi_probe(struct platform_device *pdev)
 		atari_scsi_template.sg_tablesize = SG_ALL;
 	} else {
 		atari_scsi_template.can_queue    = 1;
-		atari_scsi_template.sg_tablesize = SG_NONE;
+		atari_scsi_template.sg_tablesize = 1;
 	}
 
 	if (setup_can_queue > 0)
@@ -762,8 +762,8 @@ static int __init atari_scsi_probe(struct platform_device *pdev)
 	if (setup_cmd_per_lun > 0)
 		atari_scsi_template.cmd_per_lun = setup_cmd_per_lun;
 
-	/* Leave sg_tablesize at 0 on a Falcon! */
-	if (ATARIHW_PRESENT(TT_SCSI) && setup_sg_tablesize >= 0)
+	/* Don't increase sg_tablesize on Falcon! */
+	if (ATARIHW_PRESENT(TT_SCSI) && setup_sg_tablesize > 0)
 		atari_scsi_template.sg_tablesize = setup_sg_tablesize;
 
 	if (setup_hostid >= 0) {
drivers/scsi/mac_scsi.c +1 -1
index 5648d30c73768..5aa60bbbd09ad 100644
@@ -378,7 +378,7 @@ static int __init mac_scsi_probe(struct platform_device *pdev)
 		mac_scsi_template.can_queue = setup_can_queue;
 	if (setup_cmd_per_lun > 0)
 		mac_scsi_template.cmd_per_lun = setup_cmd_per_lun;
-	if (setup_sg_tablesize >= 0)
+	if (setup_sg_tablesize > 0)
 		mac_scsi_template.sg_tablesize = setup_sg_tablesize;
 	if (setup_hostid >= 0)
 		mac_scsi_template.this_id = setup_hostid & 7;
drivers/scsi/sun3_scsi.c +2 -2
index 3c4c07038948d..6f75693cf7d28 100644
@@ -419,7 +419,7 @@ static struct scsi_host_template sun3_scsi_template = {
 	.eh_bus_reset_handler	= sun3scsi_bus_reset,
 	.can_queue		= 16,
 	.this_id		= 7,
-	.sg_tablesize		= SG_NONE,
+	.sg_tablesize		= 1,
 	.cmd_per_lun		= 2,
 	.use_clustering		= DISABLE_CLUSTERING,
 	.cmd_size		= NCR5380_CMD_SIZE,
@@ -440,7 +440,7 @@ static int __init sun3_scsi_probe(struct platform_device *pdev)
 		sun3_scsi_template.can_queue = setup_can_queue;
 	if (setup_cmd_per_lun > 0)
 		sun3_scsi_template.cmd_per_lun = setup_cmd_per_lun;
-	if (setup_sg_tablesize >= 0)
+	if (setup_sg_tablesize > 0)
 		sun3_scsi_template.sg_tablesize = setup_sg_tablesize;
 	if (setup_hostid >= 0)
 		sun3_scsi_template.this_id = setup_hostid & 7;
Signature · 1 line
2.20.1
author maintainer
#26 lore raw

PATCH 27/42 clk: pxa: fix one of the pxa RTC clocks

In reply to Sasha Levin

From: Robert Jarzmik <[email protected]>

[ Upstream commit 46acbcb4849b2ca2e6e975e7c8130c1d61c8fd0c ]

The pxa27x platforms have a single IP with 2 drivers, sa1100-rtc and rtc-pxa drivers.

A previous patch fixed the sa1100-rtc case, but the pxa-rtc wasn't fixed. This patch completes the previous one.

Fixes 8b6d10345e16 ("clk: pxa: add missing pxa27x clocks for Irda and sa1100-rtc")
---
 drivers/clk/pxa/clk-pxa27x.c | 1 +
 1 file changed, 1 insertion(+)
drivers/clk/pxa/clk-pxa27x.c +1 -0
index c40b1804f58ca..bb556f9bbeda0 100644
@@ -362,6 +362,7 @@ struct dummy_clk {
 };
 static struct dummy_clk dummy_clks[] __initdata = {
 	DUMMY_CLK(NULL, "pxa27x-gpio", "osc_32_768khz"),
+	DUMMY_CLK(NULL, "pxa-rtc", "osc_32_768khz"),
 	DUMMY_CLK(NULL, "sa1100-rtc", "osc_32_768khz"),
 	DUMMY_CLK("UARTCLK", "pxa2xx-ir", "STUART"),
 };
Signature · 1 line
2.20.1
author maintainer
#27 lore raw

PATCH 28/42 bcache: at least try to shrink 1 node in bch_mca_scan()

In reply to Sasha Levin

From: Coly Li <[email protected]>

[ Upstream commit 9fcc34b1a6dd4b8e5337e2b6ef45e428897eca6b ]

In bch_mca_scan(), the number of shrinking btree node is calculated by code like this,

	unsigned long nr = sc->nr_to_scan;

        nr /= c->btree_pages;
        nr = min_t(unsigned long, nr, mca_can_free(c));

variable sc->nr_to_scan is number of objects (here is bcache B+tree nodes' number) to shrink, and pointer variable sc is sent from memory management code as parametr of a callback.

If sc->nr_to_scan is smaller than c->btree_pages, after the above calculation, variable 'nr' will be 0 and nothing will be shrunk. It is frequeently observed that only 1 or 2 is set to sc->nr_to_scan and make nr to be zero. Then bch_mca_scan() will do nothing more then acquiring and releasing mutex c->bucket_lock.

This patch checkes whether nr is 0 after the above calculation, if 0 is the result then set 1 to variable 'n'. Then at least bch_mca_scan() will try to shrink a single B+tree node.

---
 drivers/md/bcache/btree.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/md/bcache/btree.c +2 -0
index 4e34afb6e36a5..c8c5e3368b8b8 100644
@@ -681,6 +681,8 @@ static unsigned long bch_mca_scan(struct shrinker *shrink,
 	 * IO can always make forward progress:
 	 */
 	nr /= c->btree_pages;
+	if (nr == 0)
+		nr = 1;
 	nr = min_t(unsigned long, nr, mca_can_free(c));
 
 	i = 0;
Signature · 1 line
2.20.1
author maintainer
#28 lore raw

PATCH 29/42 ext4: fix a bug in ext4_wait_for_tail_page_commit

In reply to Sasha Levin

From: yangerkun <[email protected]>

[ Upstream commit 565333a1554d704789e74205989305c811fd9c7a ]

No need to wait for any commit once the page is fully truncated. Besides, it may confuse e.g. concurrent ext4_writepage() with the page still be dirty (will be cleared by truncate_pagecache() in ext4_setattr()) but buffers has been freed; and then trigger a bug show as below:

[   26.057508] ------------[ cut here ]------------
[   26.058531] kernel BUG at fs/ext4/inode.c:2134!
...
[   26.088130] Call trace:
[   26.088695]  ext4_writepage+0x914/0xb28
[   26.089541]  writeout.isra.4+0x1b4/0x2b8
[   26.090409]  move_to_new_page+0x3b0/0x568
[   26.091338]  __unmap_and_move+0x648/0x988
[   26.092241]  unmap_and_move+0x48c/0xbb8
[   26.093096]  migrate_pages+0x220/0xb28
[   26.093945]  kernel_mbind+0x828/0xa18
[   26.094791]  __arm64_sys_mbind+0xc8/0x138
[   26.095716]  el0_svc_common+0x190/0x490
[   26.096571]  el0_svc_handler+0x60/0xd0
[   26.097423]  el0_svc+0x8/0xc

Run the procedure (generate by syzkaller) parallel with ext3.

void main()

{
	int fd, fd1, ret;
	void *addr;
	size_t length = 4096;
	int flags;
	off_t offset = 0;
	char *str = "12345";

	fd = open("a", O_RDWR | O_CREAT);
	assert(fd >= 0);

	/* Truncate to 4k */
	ret = ftruncate(fd, length);
	assert(ret == 0);

	/* Journal data mode */
	flags = 0xc00f;
	ret = ioctl(fd, _IOW('f', 2, long), &flags);
	assert(ret == 0);

	/* Truncate to 0 */
	fd1 = open("a", O_TRUNC | O_NOATIME);
	assert(fd1 >= 0);

	addr = mmap(NULL, length, PROT_WRITE | PROT_READ,
					MAP_SHARED, fd, offset);
	assert(addr != (void *)-1);

	memcpy(addr, str, 5);
	mbind(addr, length, 0, 0, 0, MPOL_MF_MOVE);
}

And the bug will be triggered once we seen the below order.

reproduce1 reproduce2

...                            |   ...
truncate to 4k                 |
change to journal data mode    |
                               |   memcpy(set page dirty)
truncate to 0:                 |
ext4_setattr:                  |
...                            |
ext4_wait_for_tail_page_commit |
                               |   mbind(trigger bug)
truncate_pagecache(clean dirty)|   ...
...                            |

mbind will call ext4_writepage() since the page still be dirty, and then report the bug since the buffers has been free. Fix it by return directly once offset equals to 0 which means the page has been fully truncated.

---
 fs/ext4/inode.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)
fs/ext4/inode.c +8 -4
index a73056e06bdef..00c320e2ba1ee 100644
@@ -5080,11 +5080,15 @@ static void ext4_wait_for_tail_page_commit(struct inode *inode)
 
 	offset = inode->i_size & (PAGE_SIZE - 1);
 	/*
-	 * All buffers in the last page remain valid? Then there's nothing to
-	 * do. We do the check mainly to optimize the common PAGE_SIZE ==
-	 * blocksize case
+	 * If the page is fully truncated, we don't need to wait for any commit
+	 * (and we even should not as __ext4_journalled_invalidatepage() may
+	 * strip all buffers from the page but keep the page dirty which can then
+	 * confuse e.g. concurrent ext4_writepage() seeing dirty page without
+	 * buffers). Also we don't need to wait for any commit if all buffers in
+	 * the page remain valid. This is most beneficial for the common case of
+	 * blocksize == PAGESIZE.
 	 */
-	if (offset > PAGE_SIZE - i_blocksize(inode))
+	if (!offset || offset > (PAGE_SIZE - i_blocksize(inode)))
 		return;
 	while (1) {
 		page = find_lock_page(inode->i_mapping,
Signature · 1 line
2.20.1
author maintainer
#29 lore raw

PATCH 30/42 HID: Improve Windows Precision Touchpad detection.

In reply to Sasha Levin

From: Blaž Hrastnik <[email protected]>

[ Upstream commit 2dbc6f113acd74c66b04bf49fb027efd830b1c5a ]

Per Microsoft spec, usage 0xC5 (page 0xFF) returns a blob containing data used to verify the touchpad as a Windows Precision Touchpad.

   0x85, REPORTID_PTPHQA,    //    REPORT_ID (PTPHQA)
    0x09, 0xC5,              //    USAGE (Vendor Usage 0xC5)
    0x15, 0x00,              //    LOGICAL_MINIMUM (0)
    0x26, 0xff, 0x00,        //    LOGICAL_MAXIMUM (0xff)
    0x75, 0x08,              //    REPORT_SIZE (8)
    0x96, 0x00, 0x01,        //    REPORT_COUNT (0x100 (256))
    0xb1, 0x02,              //    FEATURE (Data,Var,Abs)

However, some devices, namely Microsoft's Surface line of products instead implement a "segmented device certification report" (usage 0xC6) which returns the same report, but in smaller chunks.

    0x06, 0x00, 0xff,        //     USAGE_PAGE (Vendor Defined)
    0x85, REPORTID_PTPHQA,   //     REPORT_ID (PTPHQA)
    0x09, 0xC6,              //     USAGE (Vendor usage for segment #)
    0x25, 0x08,              //     LOGICAL_MAXIMUM (8)
    0x75, 0x08,              //     REPORT_SIZE (8)
    0x95, 0x01,              //     REPORT_COUNT (1)
    0xb1, 0x02,              //     FEATURE (Data,Var,Abs)
    0x09, 0xC7,              //     USAGE (Vendor Usage)
    0x26, 0xff, 0x00,        //     LOGICAL_MAXIMUM (0xff)
    0x95, 0x20,              //     REPORT_COUNT (32)
    0xb1, 0x02,              //     FEATURE (Data,Var,Abs)

By expanding Win8 touchpad detection to also look for the segmented report, all Surface touchpads are now properly recognized by hid-multitouch.

---
 drivers/hid/hid-core.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/hid/hid-core.c +4 -0
index 42d1b350afd2a..c89eb3c3965cb 100644
@@ -761,6 +761,10 @@ static void hid_scan_feature_usage(struct hid_parser *parser, u32 usage)
 	if (usage == 0xff0000c5 && parser->global.report_count == 256 &&
 	    parser->global.report_size == 8)
 		parser->scan_flags |= HID_SCAN_FLAG_MT_WIN_8;
+
+	if (usage == 0xff0000c6 && parser->global.report_count == 1 &&
+	    parser->global.report_size == 8)
+		parser->scan_flags |= HID_SCAN_FLAG_MT_WIN_8;
 }
 
 static void hid_scan_collection(struct hid_parser *parser, unsigned type)
Signature · 1 line
2.20.1
author maintainer
#30 lore raw

PATCH 31/42 ext4: work around deleting a file with i_nlink == 0 safely

In reply to Sasha Levin

From: Theodore Ts'o <[email protected]>

[ Upstream commit c7df4a1ecb8579838ec8c56b2bb6a6716e974f37 ]

If the file system is corrupted such that a file's i_links_count is too small, then it's possible that when unlinking that file, i_nlink will already be zero. Previously we were working around this kind of corruption by forcing i_nlink to one; but we were doing this before trying to delete the directory entry --- and if the file system is corrupted enough that ext4_delete_entry() fails, then we exit with i_nlink elevated, and this causes the orphan inode list handling to be FUBAR'ed, such that when we unmount the file system, the orphan inode list can get corrupted.

A better way to fix this is to simply skip trying to call drop_nlink() if i_nlink is already zero, thus moving the check to the place where it makes the most sense.

https://bugzilla.kernel.org/show_bug.cgi?id=205433

---
 fs/ext4/namei.c | 11 +++++------
 1 file changed, 5 insertions(+), 6 deletions(-)
fs/ext4/namei.c +5 -6
index 29dc02758a52b..b8082ca9e3bac 100644
@@ -3078,18 +3078,17 @@ static int ext4_unlink(struct inode *dir, struct dentry *dentry)
 	if (IS_DIRSYNC(dir))
 		ext4_handle_sync(handle);
 
-	if (inode->i_nlink == 0) {
-		ext4_warning_inode(inode, "Deleting file '%.*s' with no links",
-				   dentry->d_name.len, dentry->d_name.name);
-		set_nlink(inode, 1);
-	}
 	retval = ext4_delete_entry(handle, dir, de, bh);
 	if (retval)
 		goto end_unlink;
 	dir->i_ctime = dir->i_mtime = ext4_current_time(dir);
 	ext4_update_dx_flag(dir);
 	ext4_mark_inode_dirty(handle, dir);
-	drop_nlink(inode);
+	if (inode->i_nlink == 0)
+		ext4_warning_inode(inode, "Deleting file '%.*s' with no links",
+				   dentry->d_name.len, dentry->d_name.name);
+	else
+		drop_nlink(inode);
 	if (!inode->i_nlink)
 		ext4_orphan_add(handle, inode);
 	inode->i_ctime = ext4_current_time(inode);
Signature · 1 line
2.20.1
author maintainer
#31 lore raw

PATCH 32/42 scsi: pm80xx: Fix for SATA device discovery

In reply to Sasha Levin

From: peter chang <[email protected]>

[ Upstream commit ce21c63ee995b7a8b7b81245f2cee521f8c3c220 ]

Driver was missing complete() call in mpi_sata_completion which result in SATA abort error handling timing out. That causes the device to be left in the in_recovery state so subsequent commands sent to the device fail and the OS removes access to it.

---
 drivers/scsi/pm8001/pm80xx_hwi.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/scsi/pm8001/pm80xx_hwi.c +2 -0
index 9edd61c063a1a..df5f0bc295875 100644
@@ -2368,6 +2368,8 @@ mpi_sata_completion(struct pm8001_hba_info *pm8001_ha, void *piomb)
 			pm8001_printk("task 0x%p done with io_status 0x%x"
 			" resp 0x%x stat 0x%x but aborted by upper layer!\n",
 			t, status, ts->resp, ts->stat));
+		if (t->slow_task)
+			complete(&t->slow_task->completion);
 		pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
 	} else {
 		spin_unlock_irqrestore(&t->task_state_lock, flags);
Signature · 1 line
2.20.1
author maintainer
#32 lore raw

PATCH 33/42 scsi: scsi_debug: num_tgts must be >= 0

In reply to Sasha Levin

From: Maurizio Lombardi <[email protected]>

[ Upstream commit aa5334c4f3014940f11bf876e919c956abef4089 ]

Passing the parameter "num_tgts=-1" will start an infinite loop that exhausts the system memory

---
 drivers/scsi/scsi_debug.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/scsi/scsi_debug.c +5 -0
index 2b0e61557317f..d7118d3767c35 100644
@@ -4953,6 +4953,11 @@ static int __init scsi_debug_init(void)
 		return -EINVAL;
 	}
 
+	if (sdebug_num_tgts < 0) {
+		pr_err("num_tgts must be >= 0\n");
+		return -EINVAL;
+	}
+
 	if (sdebug_guard > 1) {
 		pr_err("guard must be 0 or 1\n");
 		return -EINVAL;
Signature · 1 line
2.20.1
author maintainer
#33 lore raw

PATCH 34/42 scsi: target: iscsi: Wait for all commands to finish before freeing a session

In reply to Sasha Levin

From: Bart Van Assche <[email protected]>

[ Upstream commit e9d3009cb936bd0faf0719f68d98ad8afb1e613b ]

The iSCSI target driver is the only target driver that does not wait for ongoing commands to finish before freeing a session. Make the iSCSI target driver wait for ongoing commands to finish before freeing a session. This patch fixes the following KASAN complaint:

BUG: KASAN: use-after-free in __lock_acquire+0xb1a/0x2710
Read of size 8 at addr ffff8881154eca70 by task kworker/0:2/247

CPU: 0 PID: 247 Comm: kworker/0:2 Not tainted 5.4.0-rc1-dbg+ #6
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Workqueue: target_completion target_complete_ok_work [target_core_mod]
Call Trace:
 dump_stack+0x8a/0xd6
 print_address_description.constprop.0+0x40/0x60
 __kasan_report.cold+0x1b/0x33
 kasan_report+0x16/0x20
 __asan_load8+0x58/0x90
 __lock_acquire+0xb1a/0x2710
 lock_acquire+0xd3/0x200
 _raw_spin_lock_irqsave+0x43/0x60
 target_release_cmd_kref+0x162/0x7f0 [target_core_mod]
 target_put_sess_cmd+0x2e/0x40 [target_core_mod]
 lio_check_stop_free+0x12/0x20 [iscsi_target_mod]
 transport_cmd_check_stop_to_fabric+0xd8/0xe0 [target_core_mod]
 target_complete_ok_work+0x1b0/0x790 [target_core_mod]
 process_one_work+0x549/0xa40
 worker_thread+0x7a/0x5d0
 kthread+0x1bc/0x210
 ret_from_fork+0x24/0x30

Allocated by task 889:
 save_stack+0x23/0x90
 __kasan_kmalloc.constprop.0+0xcf/0xe0
 kasan_slab_alloc+0x12/0x20
 kmem_cache_alloc+0xf6/0x360
 transport_alloc_session+0x29/0x80 [target_core_mod]
 iscsi_target_login_thread+0xcd6/0x18f0 [iscsi_target_mod]
 kthread+0x1bc/0x210
 ret_from_fork+0x24/0x30

Freed by task 1025:
 save_stack+0x23/0x90
 __kasan_slab_free+0x13a/0x190
 kasan_slab_free+0x12/0x20
 kmem_cache_free+0x146/0x400
 transport_free_session+0x179/0x2f0 [target_core_mod]
 transport_deregister_session+0x130/0x180 [target_core_mod]
 iscsit_close_session+0x12c/0x350 [iscsi_target_mod]
 iscsit_logout_post_handler+0x136/0x380 [iscsi_target_mod]
 iscsit_response_queue+0x8de/0xbe0 [iscsi_target_mod]
 iscsi_target_tx_thread+0x27f/0x370 [iscsi_target_mod]
 kthread+0x1bc/0x210
 ret_from_fork+0x24/0x30

The buggy address belongs to the object at ffff8881154ec9c0
 which belongs to the cache se_sess_cache of size 352
The buggy address is located 176 bytes inside of
 352-byte region [ffff8881154ec9c0, ffff8881154ecb20)
The buggy address belongs to the page:
page:ffffea0004553b00 refcount:1 mapcount:0 mapping:ffff888101755400 index:0x0 compound_mapcount: 0
flags: 0x2fff000000010200(slab|head)
raw: 2fff000000010200 dead000000000100 dead000000000122 ffff888101755400
raw: 0000000000000000 0000000080130013 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff8881154ec900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffff8881154ec980: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
>ffff8881154eca00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                                                             ^
 ffff8881154eca80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8881154ecb00: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
---
 drivers/target/iscsi/iscsi_target.c | 10 ++++++++--
 include/scsi/iscsi_proto.h          |  1 +
 2 files changed, 9 insertions(+), 2 deletions(-)
drivers/target/iscsi/iscsi_target.c +8 -2
index b6c4f55f79e7a..e5674e5857bf8 100644
@@ -1168,7 +1168,9 @@ int iscsit_setup_scsi_cmd(struct iscsi_conn *conn, struct iscsi_cmd *cmd,
 		hdr->cmdsn, be32_to_cpu(hdr->data_length), payload_length,
 		conn->cid);
 
-	target_get_sess_cmd(&cmd->se_cmd, true);
+	if (target_get_sess_cmd(&cmd->se_cmd, true) < 0)
+		return iscsit_add_reject_cmd(cmd,
+				ISCSI_REASON_WAITING_FOR_LOGOUT, buf);
 
 	cmd->sense_reason = transport_lookup_cmd_lun(&cmd->se_cmd,
 						     scsilun_to_int(&hdr->lun));
@@ -1986,7 +1988,9 @@ iscsit_handle_task_mgt_cmd(struct iscsi_conn *conn, struct iscsi_cmd *cmd,
 			      conn->sess->se_sess, 0, DMA_NONE,
 			      TCM_SIMPLE_TAG, cmd->sense_buffer + 2);
 
-	target_get_sess_cmd(&cmd->se_cmd, true);
+	if (target_get_sess_cmd(&cmd->se_cmd, true) < 0)
+		return iscsit_add_reject_cmd(cmd,
+				ISCSI_REASON_WAITING_FOR_LOGOUT, buf);
 
 	/*
 	 * TASK_REASSIGN for ERL=2 / connection stays inside of
@@ -4243,6 +4247,8 @@ int iscsit_close_connection(
 	 * must wait until they have completed.
 	 */
 	iscsit_check_conn_usage_count(conn);
+	target_sess_cmd_list_set_waiting(sess->se_sess);
+	target_wait_for_sess_cmds(sess->se_sess);
 
 	ahash_request_free(conn->conn_tx_hash);
 	if (conn->conn_rx_hash) {
include/scsi/iscsi_proto.h +1 -0
index c1260d80ef30d..1a2ae0862e23a 100644
@@ -638,6 +638,7 @@ struct iscsi_reject {
 #define ISCSI_REASON_BOOKMARK_INVALID	9
 #define ISCSI_REASON_BOOKMARK_NO_RESOURCES	10
 #define ISCSI_REASON_NEGOTIATION_RESET	11
+#define ISCSI_REASON_WAITING_FOR_LOGOUT	12
 
 /* Max. number of Key=Value pairs in a text message */
 #define MAX_KEY_VALUE_PAIRS	8192
Signature · 1 line
2.20.1
author maintainer
#34 lore raw

PATCH 35/42 gpio: mpc8xxx: Don't overwrite default irq_set_type callback

In reply to Sasha Levin

From: Vladimir Oltean <[email protected]>

[ Upstream commit 4e50573f39229d5e9c985fa3b4923a8b29619ade ]

The per-SoC devtype structures can contain their own callbacks that overwrite mpc8xxx_gpio_devtype_default.

The clear intention is that mpc8xxx_irq_set_type is used in case the SoC does not specify a more specific callback. But what happens is that if the SoC doesn't specify one, its .irq_set_type is de-facto NULL, and this overwrites mpc8xxx_irq_set_type to a no-op. This means that the following SoCs are affected:

- fsl,mpc8572-gpio
- fsl,ls1028a-gpio
- fsl,ls1088a-gpio

On these boards, the irq_set_type does exactly nothing, and the GPIO controller keeps its GPICR register in the hardware-default state. On the LS1028A, that is ACTIVE_BOTH, which means 2 interrupts are raised even if the IRQ client requests LEVEL_HIGH. Another implication is that the IRQs are not checked (e.g. level-triggered interrupts are not rejected, although they are not supported).

Fixes 82e39b0d8566 ("gpio: mpc8xxx: handle differences between incarnations at a single place")
---
 drivers/gpio/gpio-mpc8xxx.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpio/gpio-mpc8xxx.c +2 -1
index 793518a30afe6..bd777687233b1 100644
@@ -337,7 +337,8 @@ static int mpc8xxx_probe(struct platform_device *pdev)
 	 * It's assumed that only a single type of gpio controller is available
 	 * on the current machine, so overwriting global data is fine.
 	 */
-	mpc8xxx_irq_chip.irq_set_type = devtype->irq_set_type;
+	if (devtype->irq_set_type)
+		mpc8xxx_irq_chip.irq_set_type = devtype->irq_set_type;
 
 	if (devtype->gpio_dir_out)
 		gc->direction_output = devtype->gpio_dir_out;
Signature · 1 line
2.20.1
author maintainer
#35 lore raw

PATCH 36/42 scripts/kallsyms: fix definitely-lost memory leak

In reply to Sasha Levin

From: Masahiro Yamada <[email protected]>

[ Upstream commit 21915eca088dc271c970e8351290e83d938114ac ]

build_initial_tok_table() overwrites unused sym_entry to shrink the table size. Before the entry is overwritten, table[i].sym must be freed since it is malloc'ed data.

This fixes the 'definitely lost' report from valgrind. I ran valgrind against x86_64_defconfig of v5.4-rc8 kernel, and here is the summary:

[Before the fix]

LEAK SUMMARY:

     definitely lost: 53,184 bytes in 2,874 blocks

[After the fix]

LEAK SUMMARY:
definitely lost: 0 bytes in 0 blocks

---
 scripts/kallsyms.c | 2 ++
 1 file changed, 2 insertions(+)
scripts/kallsyms.c +2 -0
index 2c8b8c662da59..6402b0d362914 100644
@@ -498,6 +498,8 @@ static void build_initial_tok_table(void)
 				table[pos] = table[i];
 			learn_symbol(table[pos].sym, table[pos].len);
 			pos++;
+		} else {
+			free(table[i].sym);
 		}
 	}
 	table_cnt = pos;
Signature · 1 line
2.20.1
author maintainer
#36 lore raw

PATCH 37/42 cdrom: respect device capabilities during opening action

In reply to Sasha Levin

From: Diego Elio Pettenò <[email protected]>

[ Upstream commit 366ba7c71ef77c08d06b18ad61b26e2df7352338 ]

Reading the TOC only works if the device can play audio, otherwise these commands fail (and possibly bring the device to an unhealthy state.)

Similarly, cdrom_mmc3_profile() should only be called if the device supports generic packet commands.

To: Jens Axboe <[email protected]>

---
 drivers/cdrom/cdrom.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)
drivers/cdrom/cdrom.c +11 -1
index a46f188f679e7..782dbab5ad56a 100644
@@ -998,6 +998,12 @@ static void cdrom_count_tracks(struct cdrom_device_info *cdi, tracktype *tracks)
 	tracks->xa = 0;
 	tracks->error = 0;
 	cd_dbg(CD_COUNT_TRACKS, "entering cdrom_count_tracks\n");
+
+	if (!CDROM_CAN(CDC_PLAY_AUDIO)) {
+		tracks->error = CDS_NO_INFO;
+		return;
+	}
+
 	/* Grab the TOC header so we can see how many tracks there are */
 	ret = cdi->ops->audio_ioctl(cdi, CDROMREADTOCHDR, &header);
 	if (ret) {
@@ -1164,7 +1170,8 @@ int cdrom_open(struct cdrom_device_info *cdi, struct block_device *bdev,
 		ret = open_for_data(cdi);
 		if (ret)
 			goto err;
-		cdrom_mmc3_profile(cdi);
+		if (CDROM_CAN(CDC_GENERIC_PACKET))
+			cdrom_mmc3_profile(cdi);
 		if (mode & FMODE_WRITE) {
 			ret = -EROFS;
 			if (cdrom_open_write(cdi))
@@ -2873,6 +2880,9 @@ int cdrom_get_last_written(struct cdrom_device_info *cdi, long *last_written)
 	   it doesn't give enough information or fails. then we return
 	   the toc contents. */
 use_toc:
+	if (!CDROM_CAN(CDC_PLAY_AUDIO))
+		return -ENOSYS;
+
 	toc.cdte_format = CDROM_MSF;
 	toc.cdte_track = CDROM_LEADOUT;
 	if ((ret = cdi->ops->audio_ioctl(cdi, CDROMREADTOCENTRY, &toc)))
Signature · 1 line
2.20.1
author maintainer
#37 lore raw

PATCH 38/42 perf regs: Make perf_reg_name() return "unknown" instead of NULL

In reply to Sasha Levin

From: Arnaldo Carvalho de Melo <[email protected]>

[ Upstream commit 5b596e0ff0e1852197d4c82d3314db5e43126bf7 ]

To avoid breaking the build on arches where this is not wired up, at least all the other features should be made available and when using this specific routine, the "unknown" should point the user/developer to the need to wire this up on this particular hardware architecture.

Detected in a container mipsel debian cross build environment, where it shows up as:

In file included from /usr/mipsel-linux-gnu/include/stdio.h:867,

                   from /git/linux/tools/perf/lib/include/perf/cpumap.h:6,
                   from util/session.c:13:
  In function 'printf',
      inlined from 'regs_dump__printf' at util/session.c:1103:3,
      inlined from 'regs__printf' at util/session.c:1131:2:
  /usr/mipsel-linux-gnu/include/bits/stdio2.h:107:10: error: '%-5s' directive argument is null [-Werror=format-overflow=]
    107 |   return __printf_chk (__USE_FORTIFY_LEVEL - 1, __fmt, __va_arg_pack ());
        |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

cross compiler details:

mipsel-linux-gnu-gcc (Debian 9.2.1-8) 9.2.1 20190909

Also on mips64:

In file included from /usr/mips64-linux-gnuabi64/include/stdio.h:867,

                   from /git/linux/tools/perf/lib/include/perf/cpumap.h:6,
                   from util/session.c:13:
  In function 'printf',
      inlined from 'regs_dump__printf' at util/session.c:1103:3,
      inlined from 'regs__printf' at util/session.c:1131:2,
      inlined from 'regs_user__printf' at util/session.c:1139:3,
      inlined from 'dump_sample' at util/session.c:1246:3,
      inlined from 'machines__deliver_event' at util/session.c:1421:3:
  /usr/mips64-linux-gnuabi64/include/bits/stdio2.h:107:10: error: '%-5s' directive argument is null [-Werror=format-overflow=]
    107 |   return __printf_chk (__USE_FORTIFY_LEVEL - 1, __fmt, __va_arg_pack ());
        |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  In function 'printf',
      inlined from 'regs_dump__printf' at util/session.c:1103:3,
      inlined from 'regs__printf' at util/session.c:1131:2,
      inlined from 'regs_intr__printf' at util/session.c:1147:3,
      inlined from 'dump_sample' at util/session.c:1249:3,
      inlined from 'machines__deliver_event' at util/session.c:1421:3:
  /usr/mips64-linux-gnuabi64/include/bits/stdio2.h:107:10: error: '%-5s' directive argument is null [-Werror=format-overflow=]
    107 |   return __printf_chk (__USE_FORTIFY_LEVEL - 1, __fmt, __va_arg_pack ());
        |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

cross compiler details:

mips64-linux-gnuabi64-gcc (Debian 9.2.1-8) 9.2.1 20190909

Fixes 2bcd355b71da ("perf tools: Add interface to arch registers sets")
Cc Adrian Hunter <[email protected]>
Cc Jiri Olsa <[email protected]>
Cc Namhyung Kim <[email protected]>
---
 tools/perf/util/perf_regs.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/perf/util/perf_regs.h +1 -1
index 679d6e4939622..e6324397b295b 100644
@@ -26,7 +26,7 @@ int perf_reg_value(u64 *valp, struct regs_dump *regs, int id);
 
 static inline const char *perf_reg_name(int id __maybe_unused)
 {
-	return NULL;
+	return "unknown";
 }
 
 static inline int perf_reg_value(u64 *valp __maybe_unused,
Signature · 1 line
2.20.1
author maintainer
#38 lore raw

PATCH 39/42 libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h

In reply to Sasha Levin

From: Masahiro Yamada <[email protected]>

[ Upstream commit a8de1304b7df30e3a14f2a8b9709bb4ff31a0385 ]

The DTC v1.5.1 added references to (U)INT32_MAX.

This is no problem for user-space programs since <stdint.h> defines (U)INT32_MAX along with (u)int32_t.

For the kernel space, libfdt_env.h needs to be adjusted before we pull in the changes.

In the kernel, we usually use s/u32 instead of (u)int32_t for the fixed-width types.

Accordingly, we already have S/U32_MAX for their max values. So, we should not add (U)INT32_MAX to <linux/limits.h> any more.

Instead, add them to the in-kernel libfdt_env.h to compile the latest libfdt.

---
 arch/arm/boot/compressed/libfdt_env.h | 4 +++-
 arch/powerpc/boot/libfdt_env.h        | 2 ++
 include/linux/libfdt_env.h            | 3 +++
 3 files changed, 8 insertions(+), 1 deletion(-)
arch/arm/boot/compressed/libfdt_env.h +3 -1
index 005bf4ff1b4cb..f3ddd4f599e3e 100644
@@ -1,11 +1,13 @@
 #ifndef _ARM_LIBFDT_ENV_H
 #define _ARM_LIBFDT_ENV_H
 
+#include <linux/limits.h>
 #include <linux/types.h>
 #include <linux/string.h>
 #include <asm/byteorder.h>
 
-#define INT_MAX			((int)(~0U>>1))
+#define INT32_MAX	S32_MAX
+#define UINT32_MAX	U32_MAX
 
 typedef __be16 fdt16_t;
 typedef __be32 fdt32_t;
arch/powerpc/boot/libfdt_env.h +2 -0
index 0b3db6322c793..5f2cb1c53e151 100644
@@ -5,6 +5,8 @@
 #include <string.h>
 
 #define INT_MAX			((int)(~0U>>1))
+#define UINT32_MAX		((u32)~0U)
+#define INT32_MAX		((s32)(UINT32_MAX >> 1))
 
 #include "of.h"
 
include/linux/libfdt_env.h +3 -0
index 8850e243c9406..bd0a55821177a 100644
@@ -6,6 +6,9 @@
 
 #include <asm/byteorder.h>
 
+#define INT32_MAX	S32_MAX
+#define UINT32_MAX	U32_MAX
+
 typedef __be16 fdt16_t;
 typedef __be32 fdt32_t;
 typedef __be64 fdt64_t;
Signature · 7 lines
2.20.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#39 lore raw

PATCH 40/42 s390/cpum_sf: Check for SDBT and SDB consistency

In reply to Sasha Levin

From: Thomas Richter <[email protected]>

[ Upstream commit 247f265fa502e7b17a0cb0cc330e055a36aafce4 ]

Each SBDT is located at a 4KB page and contains 512 entries. Each entry of a SDBT points to a SDB, a 4KB page containing sampled data. The last entry is a link to another SDBT page.

When an event is created the function sequence executed is:

__hw_perf_event_init()

  +--> allocate_buffers()
       +--> realloc_sampling_buffers()
	    +---> alloc_sample_data_block()

Both functions realloc_sampling_buffers() and alloc_sample_data_block() allocate pages and the allocation can fail. This is handled correctly and all allocated pages are freed and error -ENOMEM is returned to the top calling function. Finally the event is not created.

Once the event has been created, the amount of initially allocated SDBT and SDB can be too low. This is detected during measurement interrupt handling, where the amount of lost samples is calculated. If the number of lost samples is too high considering sampling frequency and already allocated SBDs, the number of SDBs is enlarged during the next execution of cpumsf_pmu_enable().

If more SBDs need to be allocated, functions

       realloc_sampling_buffers()
       +---> alloc-sample_data_block()

are called to allocate more pages. Page allocation may fail and the returned error is ignored. A SDBT and SDB setup already exists.

However the modified SDBTs and SDBs might end up in a situation where the first entry of an SDBT does not point to an SDB, but another SDBT, basicly an SBDT without payload. This can not be handled by the interrupt handler, where an SDBT must have at least one entry pointing to an SBD.

Add a check to avoid SDBTs with out payload (SDBs) when enlarging the buffer setup.

---
 arch/s390/kernel/perf_cpum_sf.c | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)
arch/s390/kernel/perf_cpum_sf.c +15 -2
index f46e5c0cb6d95..02476d2333df3 100644
@@ -185,7 +185,7 @@ static int realloc_sampling_buffer(struct sf_buffer *sfb,
 				   unsigned long num_sdb, gfp_t gfp_flags)
 {
 	int i, rc;
-	unsigned long *new, *tail;
+	unsigned long *new, *tail, *tail_prev = NULL;
 
 	if (!sfb->sdbt || !sfb->tail)
 		return -EINVAL;
@@ -224,6 +224,7 @@ static int realloc_sampling_buffer(struct sf_buffer *sfb,
 			sfb->num_sdbt++;
 			/* Link current page to tail of chain */
 			*tail = (unsigned long)(void *) new + 1;
+			tail_prev = tail;
 			tail = new;
 		}
 
@@ -233,10 +234,22 @@ static int realloc_sampling_buffer(struct sf_buffer *sfb,
 		 * issue, a new realloc call (if required) might succeed.
 		 */
 		rc = alloc_sample_data_block(tail, gfp_flags);
-		if (rc)
+		if (rc) {
+			/* Undo last SDBT. An SDBT with no SDB at its first
+			 * entry but with an SDBT entry instead can not be
+			 * handled by the interrupt handler code.
+			 * Avoid this situation.
+			 */
+			if (tail_prev) {
+				sfb->num_sdbt--;
+				free_page((unsigned long) new);
+				tail = tail_prev;
+			}
 			break;
+		}
 		sfb->num_sdb++;
 		tail++;
+		tail_prev = new = NULL;	/* Allocated at least one SBD */
 	}
 
 	/* Link sampling buffer to its origin */
Signature · 1 line
2.20.1
author maintainer
#40 lore raw

PATCH 41/42 ocfs2: fix passing zero to 'PTR_ERR' warning

In reply to Sasha Levin

From: Ding Xiang <[email protected]>

[ Upstream commit 188c523e1c271d537f3c9f55b6b65bf4476de32f ]

Fix a static code checker warning:
fs/ocfs2/acl.c:331
ocfs2_acl_chmod() warn: passing zero to 'PTR_ERR'

Fixes 5ee0fbd50fd ("ocfs2: revert using ocfs2_acl_chmod to avoid inode cluster lock hang")
Cc Mark Fasheh <[email protected]>
Cc Joel Becker <[email protected]>
Cc Junxiao Bi <[email protected]>
Cc Changwei Ge <[email protected]>
Cc Gang He <[email protected]>
Cc Jun Piao <[email protected]>
---
 fs/ocfs2/acl.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
fs/ocfs2/acl.c +2 -2
index ee8dbbae78b6a..6dc714a56c37a 100644
@@ -338,8 +338,8 @@ int ocfs2_acl_chmod(struct inode *inode, struct buffer_head *bh)
 	down_read(&OCFS2_I(inode)->ip_xattr_sem);
 	acl = ocfs2_get_acl_nolock(inode, ACL_TYPE_ACCESS, bh);
 	up_read(&OCFS2_I(inode)->ip_xattr_sem);
-	if (IS_ERR(acl) || !acl)
-		return PTR_ERR(acl);
+	if (IS_ERR_OR_NULL(acl))
+		return PTR_ERR_OR_ZERO(acl);
 	ret = __posix_acl_chmod(&acl, GFP_KERNEL, inode->i_mode);
 	if (ret)
 		return ret;
Signature · 1 line
2.20.1
author maintainer
#41 lore raw

PATCH 42/42 kernel: sysctl: make drop_caches write-only

In reply to Sasha Levin

From: Johannes Weiner <[email protected]>

[ Upstream commit 204cb79ad42f015312a5bbd7012d09c93d9b46fb ]

Currently, the drop_caches proc file and sysctl read back the last value written, suggesting this is somehow a stateful setting instead of a one-time command. Make it write-only, like e.g. compact_memory.

While mitigating a VM problem at scale in our fleet, there was confusion about whether writing to this file will permanently switch the kernel into a non-caching mode. This influences the decision making in a tense situation, where tens of people are trying to fix tens of thousands of affected machines: Do we need a rollback strategy? What are the performance implications of operating in a non-caching state for several days? It also caused confusion when the kernel team said we may need to write the file several times to make sure it's effective ("But it already reads back 3?").

---
 kernel/sysctl.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/sysctl.c +1 -1
index 6af1ac551ea3a..34449ec0689d0 100644
@@ -1398,7 +1398,7 @@ static struct ctl_table vm_table[] = {
 		.procname	= "drop_caches",
 		.data		= &sysctl_drop_caches,
 		.maxlen		= sizeof(int),
-		.mode		= 0644,
+		.mode		= 0200,
 		.proc_handler	= drop_caches_sysctl_handler,
 		.extra1		= &one,
 		.extra2		= &four,
Signature · 1 line
2.20.1