arm64: dts: qcom: sc7180: Add nodes for eMMC and SD card
Subsystems (5)
PATCH v2 1/1 arm64: dts: qcom: sc7180: Add nodes for eMMC and SD card
Add sdhc instances for supporting eMMC and SD-card on sc7180. The regulators should be in HPM state for proper functionality of eMMC and SD-card. Updating corresponding regulators accordingly.
---
This depends on the patch series (dt support for sc7180):
https://lkml.org/lkml/2019/11/8/149
Also depends on documentation commit 2078158 (Present on mmc-next)
Changes since V1:
- Updated the regulator min, max voltages as per eMMC/SD-card voltage requirements
- Enabled IOMMU for eMMC and SD-card.
- Added pull and drive strength to SD-card cd-gpio.
- Incorporated review comments by Matthias Kaehlcke.
--- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++--- arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++ 2 files changed, 183 insertions(+), 12 deletions(-)
arch/arm64/boot/dts/qcom/sc7180-idp.dts +35 -12
@@ -7,6 +7,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sc7180.dtsi" #include "pm6150.dtsi"
@@ -101,9 +102,9 @@ }; vreg_l12a_1p8: ldo12 { - regulator-min-microvolt = <1696000>; - regulator-max-microvolt = <1952000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l13a_1p8: ldo13 {
@@ -143,9 +144,9 @@ }; vreg_l19a_2p9: ldo19 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; };
@@ -189,9 +190,9 @@ }; vreg_l6c_2p9: ldo6 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l7c_3p0: ldo7 {
@@ -207,9 +208,9 @@ }; vreg_l9c_2p9: ldo9 { - regulator-min-microvolt = <2952000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l10c_3p3: ldo10 {
@@ -400,3 +401,25 @@ bias-pull-up; }; }; + +&sdhc_1 { + status = "ok"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + vmmc-supply = <&vreg_l19a_2p9>; + vqmmc-supply = <&vreg_l12a_1p8>; +}; + +&sdhc_2 { + status = "ok"; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + + cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>; +};
arch/arm64/boot/dts/qcom/sc7180.dtsi +148 -0
160 lines not on this page · raw message
Signature · 1 line
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc., is a member of Code Aurora Forum, a Linux Foundation Collaborative Project
Quoted 5 lines · Veerabhadrarao Badiganti
Add sdhc instances for supporting eMMC and SD-card on sc7180. The regulators should be in HPM state for proper functionality of eMMC and SD-card. Updating corresponding regulators accordingly.
Signed-off-by Veerabhadrarao Badiganti <[email protected]>
The patch doesn't apply against qcom/for-next, looks like you need to rebase it.
Quoted 97 lines
---
This depends on the patch series (dt support for sc7180):
https://lkml.org/lkml/2019/11/8/149
Also depends on documentation commit 2078158 (Present on mmc-next)Changes since V1:
- Updated the regulator min, max voltages as per eMMC/SD-card voltage requirements
- Enabled IOMMU for eMMC and SD-card.
- Added pull and drive strength to SD-card cd-gpio.
- Incorporated review comments by Matthias Kaehlcke.--- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++--- arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++ 2 files changed, 183 insertions(+), 12 deletions(-)arch/arm64/boot/dts/qcom/sc7180-idp.dts +25
-12@@ -7,6 +7,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sc7180.dtsi" #include "pm6150.dtsi"@@ -101,9 +102,9 @@ }; vreg_l12a_1p8: ldo12 { - regulator-min-microvolt = <1696000>; - regulator-max-microvolt = <1952000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l13a_1p8: ldo13 {@@ -143,9 +144,9 @@ }; vreg_l19a_2p9: ldo19 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; };@@ -189,9 +190,9 @@ }; vreg_l6c_2p9: ldo6 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l7c_3p0: ldo7 {@@ -207,9 +208,9 @@ }; vreg_l9c_2p9: ldo9 { - regulator-min-microvolt = <2952000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l10c_3p3: ldo10 {@@ -400,3 +401,25 @@ bias-pull-up; }; }; + +&sdhc_1 { + status = "ok"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + vmmc-supply = <&vreg_l19a_2p9>; + vqmmc-supply = <&vreg_l12a_1p8>; +}; + +&sdhc_2 {
arch/arm64/boot/dts/qcom/sc7180-idp.dts line 425
Quoted 10 lines
arch/arm64/boot/dts/qcom/sc7180-idp.dts +10
-0+ status = "ok"; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + + cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>; +};
You are adding these entries to the pinctrl section, they belong above the "/* PINCTRL - additions to nodes defined in sc7180.dtsi */" comment.
Quoted 38 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +26
-0@@ -182,6 +182,32 @@ #power-domain-cells = <1>; }; + sdhc_1: sdhci@7c4000 { + compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x7c4000 0 0x1000>; + reg-names = "hc_mem"; + + interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_APPS_CLK>, + <&gcc GCC_SDCC1_AHB_CLK>; + clock-names = "core", "iface"; + + iommus = <&apps_smmu 0x60 0x0>; + + bus-width = <8>; + non-removable; + + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + + status = "disabled"; + }; + qupv3_id_0: geniqup@8c0000 { compatible = "qcom,geni-se-qup"; reg = <0 0x008c0000 0 0x6000>;
arch/arm64/boot/dts/qcom/sc7180.dtsi line 928
Quoted 6 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +3
-0@@ -897,6 +923,128 @@ function = "qup15"; }; }; + + sdc1_on: sdc1-on { + clk {
judging from some other nodes the convention seems to be to call the nodes 'pinconf-<name>'.
Quoted 6 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +6
-0+ pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd {
arch/arm64/boot/dts/qcom/sc7180.dtsi line 944
Quoted 10 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +10
-0+ pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <10>; + };
cmd and data have the same configuration, in theory you could combine them in a single node. Not sure if it's strictly required, in this case with just two pins it doesn't make a big difference.
Quoted 23 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +23
-0+ + rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc1_off: sdc1-off { + clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data { + pins = "sdc1_data"; + bias-pull-up;
arch/arm64/boot/dts/qcom/sc7180.dtsi line 977
Quoted 10 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +10
-0+ drive-strength = <2>; + }; + + rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc2_on: sdc2_on {
nit: sdc2_on: sdc2-on
Quoted 16 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +16
-0+ clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>;
arch/arm64/boot/dts/qcom/sc7180.dtsi line 1003
Quoted 10 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +10
-0+ }; + + sd-cd { + pins = "gpio69"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_off: sdc2_off {
nit: sdc2_off: sdc2-off
Quoted 178 lines · Matthias Kaehlcke
Quoted 5 lines · Veerabhadrarao Badiganti
Add sdhc instances for supporting eMMC and SD-card on sc7180. The regulators should be in HPM state for proper functionality of eMMC and SD-card. Updating corresponding regulators accordingly.
Signed-off-by Veerabhadrarao Badiganti <[email protected]>The patch doesn't apply against qcom/for-next, looks like you need to rebase it.
Quoted 97 lines
---
This depends on the patch series (dt support for sc7180):
https://lkml.org/lkml/2019/11/8/149
Also depends on documentation commit 2078158 (Present on mmc-next)Changes since V1:
- Updated the regulator min, max voltages as per eMMC/SD-card voltage requirements
- Enabled IOMMU for eMMC and SD-card.
- Added pull and drive strength to SD-card cd-gpio.
- Incorporated review comments by Matthias Kaehlcke.--- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++--- arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++ 2 files changed, 183 insertions(+), 12 deletions(-)arch/arm64/boot/dts/qcom/sc7180-idp.dts +25
-12@@ -7,6 +7,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sc7180.dtsi" #include "pm6150.dtsi"@@ -101,9 +102,9 @@ }; vreg_l12a_1p8: ldo12 { - regulator-min-microvolt = <1696000>; - regulator-max-microvolt = <1952000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l13a_1p8: ldo13 {@@ -143,9 +144,9 @@ }; vreg_l19a_2p9: ldo19 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; };@@ -189,9 +190,9 @@ }; vreg_l6c_2p9: ldo6 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l7c_3p0: ldo7 {@@ -207,9 +208,9 @@ }; vreg_l9c_2p9: ldo9 { - regulator-min-microvolt = <2952000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l10c_3p3: ldo10 {@@ -400,3 +401,25 @@ bias-pull-up; }; }; + +&sdhc_1 { + status = "ok"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + vmmc-supply = <&vreg_l19a_2p9>; + vqmmc-supply = <&vreg_l12a_1p8>; +}; + +&sdhc_2 {arch/arm64/boot/dts/qcom/sc7180-idp.dts line 425
Quoted 10 lines
arch/arm64/boot/dts/qcom/sc7180-idp.dts +10
-0+ status = "ok"; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + + cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>; +};You are adding these entries to the pinctrl section, they belong above the "/* PINCTRL - additions to nodes defined in
sc7180.dtsi*/" comment.Quoted 38 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +26
-0@@ -182,6 +182,32 @@ #power-domain-cells = <1>; }; + sdhc_1: sdhci@7c4000 { + compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x7c4000 0 0x1000>; + reg-names = "hc_mem"; + + interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_APPS_CLK>, + <&gcc GCC_SDCC1_AHB_CLK>; + clock-names = "core", "iface"; + + iommus = <&apps_smmu 0x60 0x0>; + + bus-width = <8>; + non-removable; + + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + + status = "disabled"; + }; + qupv3_id_0: geniqup@8c0000 { compatible = "qcom,geni-se-qup"; reg = <0 0x008c0000 0 0x6000>;arch/arm64/boot/dts/qcom/sc7180.dtsi line 928
Quoted 6 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +3
-0@@ -897,6 +923,128 @@ function = "qup15"; }; }; + + sdc1_on: sdc1-on { + clk {judging from some other nodes the convention seems to be to call the nodes 'pinconf-<name>'.
Quoted 11 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +11
-0+ pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <10>; + }; +
Quoted 8 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi line 944
Quoted 5 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +5
-0+ data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <10>; + };cmd and data have the same configuration, in theory you could combine them in a single node. Not sure if it's strictly required, in this case with just two pins it doesn't make a big difference.
Though both have same configuration, each corresponds to different bit fields in register
for updating drive-strengths and pull. It configures the right bit field based on pin name.
So separate pins needed for cmd and data here.
Quoted 54 lines
Quoted 23 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +23
-0+ + rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc1_off: sdc1-off { + clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data { + pins = "sdc1_data"; + bias-pull-up;arch/arm64/boot/dts/qcom/sc7180.dtsi line 977
Quoted 10 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +10
-0+ drive-strength = <2>; + }; + + rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc2_on: sdc2_on {nit:
sdc2_on: sdc2-onQuoted 19 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +19
-0+ clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + sd-cd {
Quoted 8 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi line 1003
Quoted 7 lines
arch/arm64/boot/dts/qcom/sc7180.dtsi +7
-0+ pins = "gpio69"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_off: sdc2_off {nit:
sdc2_off: sdc2-off
Will incorporate the rest of the changes that you commented.
Thanks,
Veera
Quoted 87 lines · Veerabhadrarao Badiganti
Add sdhc instances for supporting eMMC and SD-card on sc7180. The regulators should be in HPM state for proper functionality of eMMC and SD-card. Updating corresponding regulators accordingly.
Signed-off-by Veerabhadrarao Badiganti <[email protected]>---
This depends on the patch series (dt support for sc7180):
https://lkml.org/lkml/2019/11/8/149
Also depends on documentation commit 2078158 (Present on mmc-next)Changes since V1:
- Updated the regulator min, max voltages as per eMMC/SD-card voltage requirements
- Enabled IOMMU for eMMC and SD-card.
- Added pull and drive strength to SD-card cd-gpio.
- Incorporated review comments by Matthias Kaehlcke.--- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++--- arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++ 2 files changed, 183 insertions(+), 12 deletions(-)arch/arm64/boot/dts/qcom/sc7180-idp.dts +13
-12@@ -7,6 +7,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sc7180.dtsi" #include "pm6150.dtsi"@@ -101,9 +102,9 @@ }; vreg_l12a_1p8: ldo12 { - regulator-min-microvolt = <1696000>; - regulator-max-microvolt = <1952000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l13a_1p8: ldo13 {@@ -143,9 +144,9 @@ }; vreg_l19a_2p9: ldo19 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; };@@ -189,9 +190,9 @@ }; vreg_l6c_2p9: ldo6 { - regulator-min-microvolt = <2696000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l7c_3p0: ldo7 {@@ -207,9 +208,9 @@ }; vreg_l9c_2p9: ldo9 { - regulator-min-microvolt = <2952000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l10c_3p3: ldo10 {
arch/arm64/boot/dts/qcom/sc7180-idp.dts line 406
Quoted 6 lines
arch/arm64/boot/dts/qcom/sc7180-idp.dts +3
-0@@ -400,3 +401,25 @@ bias-pull-up; }; }; + +&sdhc_1 { + status = "ok";
another nit: the DT code is fine with both "okay" and "ok", however the rest of this file uses "okay", so let's be consistent and use the same string in all nodes.
arch/arm64/boot/dts/qcom/sc7180-idp.dts line 416
Quoted 10 lines
arch/arm64/boot/dts/qcom/sc7180-idp.dts +10
-0+ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + vmmc-supply = <&vreg_l19a_2p9>; + vqmmc-supply = <&vreg_l12a_1p8>; +}; + +&sdhc_2 { + status = "ok";
ditto