mtd: rawnand: denali_dt: Add support for configuring SPARE_AREA_SKIP_BYTES
Subsystems (3)
PATCH v2 1/1 mtd: rawnand: denali_dt: Add support for configuring SPARE_AREA_SKIP_BYTES
The SPARE_AREA_SKIP_BYTES register is reset when the controller reset signal is toggled. Yet, this register must be configured to match the content of the NAND OOB area. The current default value is always set to 8 and is programmed into the hardware in case the hardware was not programmed before (e.g. in a bootloader) with a different value. This however does not work when the block is reset properly by Linux.
On Altera SoCFPGA CycloneV, ArriaV and Arria10, which are the SoCFPGA platforms which support booting from NAND, the SPARE_AREA_SKIP_BYTES value must be set to 2. On Socionext Uniphier, the value is 8. This patch adds support for preconfiguring the default value and handles the special SoCFPGA case by setting the default to 2 on all SoCFPGA platforms, while retaining the original behavior and default value of 8 on all the other platforms.
---
V2: Move denali->oob_skip_bytes = data->oob_skip_bytes; right after
of_device_get_match_data()
--- drivers/mtd/nand/raw/denali.c | 13 ++++++++++--- drivers/mtd/nand/raw/denali_dt.c | 5 +++++ 2 files changed, 15 insertions(+), 3 deletions(-)
drivers/mtd/nand/raw/denali.c +10 -3
@@ -1302,14 +1302,21 @@ int denali_init(struct denali_controller *denali)/* * Set how many bytes should be skipped before writing data in OOB. +* If a non-zero value has already been configured, update it in HW. * If a non-zero value has already been set (by firmware or something), * just use it. Otherwise, set the driver's default. */ - denali->oob_skip_bytes =ioread32 (denali->reg +SPARE_AREA_SKIP_BYTES ); -if (!denali->oob_skip_bytes) { - denali->oob_skip_bytes =DENALI_DEFAULT_OOB_SKIP_BYTES ; +if (denali->oob_skip_bytes) {iowrite32 (denali->oob_skip_bytes, denali->reg +SPARE_AREA_SKIP_BYTES ); + }else { + denali->oob_skip_bytes = +ioread32 (denali->reg +SPARE_AREA_SKIP_BYTES ); +if (!denali->oob_skip_bytes) { + denali->oob_skip_bytes =DENALI_DEFAULT_OOB_SKIP_BYTES ; +iowrite32 (denali->oob_skip_bytes, + denali->reg +SPARE_AREA_SKIP_BYTES ); + } }iowrite32 (0 , denali->reg +TRANSFER_SPARE_REG );
drivers/mtd/nand/raw/denali_dt.c +5 -0
@@ -27,6 +27,7 @@ struct denali_dt {struct denali_dt_data {unsigned int revision;unsigned int caps; +unsigned int oob_skip_bytes;const struct nand_ecc_caps *ecc_caps; };
@@ -34,6 +35,7 @@ NAND_ECC_CAPS_SINGLE(denali_socfpga_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);static const struct denali_dt_data denali_socfpga_data = { .caps =DENALI_CAP_HW_ECC_FIXUP , + .oob_skip_bytes =2 , .ecc_caps = &denali_socfpga_ecc_caps, };
@@ -42,6 +44,7 @@ NAND_ECC_CAPS_SINGLE(denali_uniphier_v5a_ecc_caps, denali_calc_ecc_bytes,static const struct denali_dt_data denali_uniphier_v5a_data = { .caps =DENALI_CAP_HW_ECC_FIXUP |DENALI_CAP_DMA_64BIT , + .oob_skip_bytes =8 , .ecc_caps = &denali_uniphier_v5a_ecc_caps, };
@@ -51,6 +54,7 @@ static const struct denali_dt_data denali_uniphier_v5b_data = { .revision = 0x0501, .caps = DENALI_CAP_HW_ECC_FIXUP | DENALI_CAP_DMA_64BIT, + .oob_skip_bytes = 8, .ecc_caps = &denali_uniphier_v5b_ecc_caps, };
@@ -122,6 +126,7 @@ static int denali_dt_probe(struct platform_device *pdev) denali->revision = data->revision; denali->caps = data->caps; denali->ecc_caps = data->ecc_caps; + denali->oob_skip_bytes = data->oob_skip_bytes; } denali->dev = dev;
Signature · 6 lines
2.24.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Quoted 21 lines · Marek Vasut
The
SPARE_AREA_SKIP_BYTESregister is reset when the controller reset signal is toggled. Yet, this register must be configured to match the content of the NAND OOB area. The current default value is always set to 8 and is programmed into the hardware in case the hardware was not programmed before (e.g. in a bootloader) with a different value. This however does not work when the block is reset properly by Linux.On Altera SoCFPGA CycloneV, ArriaV and Arria10, which are the SoCFPGA platforms which support booting from NAND, the
SPARE_AREA_SKIP_BYTESvalue must be set to 2. On Socionext Uniphier, the value is 8. This patch adds support for preconfiguring the default value and handles the special SoCFPGA case by setting the default to 2 on all SoCFPGA platforms, while retaining the original behavior and default value of 8 on all the other platforms.Signed-off-by Marek Vasut <[email protected]>Cc Masahiro Yamada <[email protected]>Cc Miquel Raynal <[email protected]>Cc Richard Weinberger <[email protected]>Cc Vignesh Raghavendra <[email protected]>
Quoted 5 lines
Reviewed-by Tudor Ambarus <[email protected]>---
V2: Movedenali->oob_skip_bytes=data->oob_skip_bytes; right after
of_device_get_match_data()
FYI.
This patch was rebased to avoid a conflict:
http://patchwork.ozlabs.org/patch/1214018/
My Ack is in v3.
I solved a merge conflict, and bundled in a series:
http://patchwork.ozlabs.org/project/linux-mtd/list/?series=149821
Quoted 85 lines
--- drivers/mtd/nand/raw/denali.c | 13 ++++++++++--- drivers/mtd/nand/raw/denali_dt.c | 5 +++++ 2 files changed, 15 insertions(+), 3 deletions(-)drivers/mtd/nand/raw/denali.c +10
-3@@ -1302,14 +1302,21 @@ int denali_init(struct denali_controller *denali)/* * Set how many bytes should be skipped before writing data in OOB. +* If a non-zero value has already been configured, update it in HW. * If a non-zero value has already been set (by firmware or something), * just use it. Otherwise, set the driver's default. */ - denali->oob_skip_bytes =ioread32 (denali->reg +SPARE_AREA_SKIP_BYTES ); -if (!denali->oob_skip_bytes) { - denali->oob_skip_bytes =DENALI_DEFAULT_OOB_SKIP_BYTES ; +if (denali->oob_skip_bytes) {iowrite32 (denali->oob_skip_bytes, denali->reg +SPARE_AREA_SKIP_BYTES ); + }else { + denali->oob_skip_bytes = +ioread32 (denali->reg +SPARE_AREA_SKIP_BYTES ); +if (!denali->oob_skip_bytes) { + denali->oob_skip_bytes =DENALI_DEFAULT_OOB_SKIP_BYTES ; +iowrite32 (denali->oob_skip_bytes, + denali->reg +SPARE_AREA_SKIP_BYTES ); + } }iowrite32 (0 , denali->reg +TRANSFER_SPARE_REG );drivers/mtd/nand/raw/denali_dt.c +5
-1@@ -27,6 +27,7 @@ struct denali_dt {struct denali_dt_data {unsigned int revision;unsigned int caps; +unsigned int oob_skip_bytes;const struct nand_ecc_caps *ecc_caps; };@@ -34,6 +35,7 @@ NAND_ECC_CAPS_SINGLE(denali_socfpga_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);static const struct denali_dt_data denali_socfpga_data = { .caps =DENALI_CAP_HW_ECC_FIXUP , + .oob_skip_bytes =2 , .ecc_caps = &denali_socfpga_ecc_caps, };@@ -42,6 +44,7 @@ NAND_ECC_CAPS_SINGLE(denali_uniphier_v5a_ecc_caps, denali_calc_ecc_bytes,static const struct denali_dt_data denali_uniphier_v5a_data = { .caps =DENALI_CAP_HW_ECC_FIXUP |DENALI_CAP_DMA_64BIT , + .oob_skip_bytes =8 , .ecc_caps = &denali_uniphier_v5a_ecc_caps, };@@ -51,6 +54,7 @@ static const struct denali_dt_data denali_uniphier_v5b_data = { .revision = 0x0501, .caps = DENALI_CAP_HW_ECC_FIXUP | DENALI_CAP_DMA_64BIT, + .oob_skip_bytes = 8, .ecc_caps = &denali_uniphier_v5b_ecc_caps, };@@ -122,6 +126,7 @@ static int denali_dt_probe(struct platform_device *pdev) denali->revision = data->revision; denali->caps = data->caps; denali->ecc_caps = data->ecc_caps; + denali->oob_skip_bytes = data->oob_skip_bytes; } denali->dev = dev; --2.24.1
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Signature · 6 lines
Best Regards Masahiro Yamada ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Miquel Raynal
maintainerHi Masahiro,
Masahiro Yamada <[email protected]> wrote on Fri, 10 Jan 2020 01:06:20 +0900:
Quoted 29 lines · Marek Vasut
Quoted 21 lines
The
SPARE_AREA_SKIP_BYTESregister is reset when the controller reset signal is toggled. Yet, this register must be configured to match the content of the NAND OOB area. The current default value is always set to 8 and is programmed into the hardware in case the hardware was not programmed before (e.g. in a bootloader) with a different value. This however does not work when the block is reset properly by Linux.On Altera SoCFPGA CycloneV, ArriaV and Arria10, which are the SoCFPGA platforms which support booting from NAND, the
SPARE_AREA_SKIP_BYTESvalue must be set to 2. On Socionext Uniphier, the value is 8. This patch adds support for preconfiguring the default value and handles the special SoCFPGA case by setting the default to 2 on all SoCFPGA platforms, while retaining the original behavior and default value of 8 on all the other platforms.Signed-off-by Marek Vasut <[email protected]>Cc Masahiro Yamada <[email protected]>Cc Miquel Raynal <[email protected]>Cc Richard Weinberger <[email protected]>Cc Vignesh Raghavendra <[email protected]>Quoted 5 lines
Reviewed-by Tudor Ambarus <[email protected]>---
V2: Movedenali->oob_skip_bytes=data->oob_skip_bytes; right after
of_device_get_match_data()
Quoted 6 lines
FYI.
This patch was rebased to avoid a conflict:
http://patchwork.ozlabs.org/patch/1214018/My Ack is in v3.
It is indeed about to be applied :)
Cheers,
Miquèl
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/