enetc: add support time specific departure base on the qos etf
Subsystems (3)
ENETC implement time specific departure capability, which enables the user to specify when a frame can be transmitted. When this capability is enabled, the device will delay the transmission of the frame so that it can be transmitted at the precisely specified time. The delay departure time up to 0.5 seconds in the future. If the departure time in the transmit BD has not yet been reached, based on the current time, the packet will not be transmitted.
This driver was loaded by Qos driver ETF. User could load it by tc commands. Here are the example commands:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 etf \
clockid CLOCK_TAI delta 30000 offload
These example try to set queue mapping first and then set queue 7 with 30us ahead dequeue time.
Then user send test frame should set SO_TXTIME feature for socket.
There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure operation are mutually exclusive.
--- drivers/net/ethernet/freescale/enetc/enetc.c | 12 +++++++ drivers/net/ethernet/freescale/enetc/enetc.h | 3 ++ .../net/ethernet/freescale/enetc/enetc_hw.h | 10 +++++- .../net/ethernet/freescale/enetc/enetc_qos.c | 31 +++++++++++++++++++ 4 files changed, 55 insertions(+), 1 deletion(-)
drivers/net/ethernet/freescale/enetc/enetc.c +12 -0
@@ -149,11 +149,21 @@ static int enetc_map_tx_buffs(struct enetc_bdr *tx_ring, struct sk_buff *skb,if (enetc_tx_csum (skb, &temp_bd)) flags |=ENETC_TXBD_FLAGS_CSUM |ENETC_TXBD_FLAGS_L4CS ; +else if (tx_ring->tsd_enable) + flags |=ENETC_TXBD_FLAGS_TSE |ENETC_TXBD_FLAGS_TXSTART ;/* first BD needs frm_len and offload flags set */ temp_bd.frm_len =cpu_to_le16 (skb->len); temp_bd.flags = flags; +if (flags &ENETC_TXBD_FLAGS_TSE ) { +u32 temp; + + temp = (skb->skb_mstamp_ns >>5 &ENETC_TXBD_TXSTART_MASK ) + | (flags <<ENETC_TXBD_FLAGS_OFFSET ); + temp_bd.txstart =cpu_to_le32 (temp); + } +if (flags &ENETC_TXBD_FLAGS_EX ) {u8 e_flags =0 ; *txbd = temp_bd;
@@ -1505,6 +1515,8 @@ int enetc_setup_tc(struct net_device *ndev, enum tc_setup_type type,return enetc_setup_tc_taprio (ndev, type_data);case TC_SETUP_QDISC_CBS :return enetc_setup_tc_cbs (ndev, type_data); +case TC_SETUP_QDISC_ETF : +return enetc_setup_tc_txtime (ndev, type_data);default :return -EOPNOTSUPP ; }
drivers/net/ethernet/freescale/enetc/enetc.h +3 -0
@@ -72,6 +72,7 @@ struct enetc_bdr {struct enetc_ring_stats stats;dma_addr_t bd_dma_base; +u8 tsd_enable;/* Time specific departure */ }____cacheline_aligned_in_smp ;static inline void enetc_bdr_idx_inc (struct enetc_bdr *bdr,int *i)
@@ -256,8 +257,10 @@ int enetc_send_cmd(struct enetc_si *si, struct enetc_cbd *cbd);int enetc_setup_tc_taprio (struct net_device *ndev,void *type_data);void enetc_sched_speed_set (struct net_device *ndev);int enetc_setup_tc_cbs (struct net_device *ndev,void *type_data); +int enetc_setup_tc_txtime (struct net_device *ndev,void *type_data);#else #define enetc_setup_tc_taprio (ndev, type_data) -EOPNOTSUPP#define enetc_sched_speed_set (ndev) (void)0#define enetc_setup_tc_cbs (ndev, type_data) -EOPNOTSUPP +#define enetc_setup_tc_txtime (ndev, type_data) -EOPNOTSUPP#endif
drivers/net/ethernet/freescale/enetc/enetc_hw.h +9 -1
@@ -358,6 +358,7 @@ union enetc_tx_bd {u8 l4_csoff;u8 flags; };/* default layout */ +__le32 txstart;__le32 lstatus; }; };
@@ -378,11 +379,14 @@ union enetc_tx_bd { };#define ENETC_TXBD_FLAGS_L4CS BIT(0) +#define ENETC_TXBD_FLAGS_TSE BIT(1)#define ENETC_TXBD_FLAGS_W BIT(2)#define ENETC_TXBD_FLAGS_CSUM BIT(3) +#define ENETC_TXBD_FLAGS_TXSTART BIT(4)#define ENETC_TXBD_FLAGS_EX BIT(6)#define ENETC_TXBD_FLAGS_F BIT(7) - +#define ENETC_TXBD_TXSTART_MASK GENMASK(24, 0) +#define ENETC_TXBD_FLAGS_OFFSET 24static inline void enetc_clear_tx_bd (union enetc_tx_bd *txbd) {memset (txbd,0 ,sizeof (*txbd));
@@ -615,3 +619,7 @@ struct enetc_cbd {/* Port time gating capability register */ #define ENETC_QBV_PTGCAPR_OFFSET 0x11a08#define ENETC_QBV_MAX_GCL_LEN_MASK GENMASK(15, 0) + +/* Port time specific departure */ +#define ENETC_PTCTSDR (n) (0x1210 + 4 * (n)) +#define ENETC_TSDE BIT(31)
drivers/net/ethernet/freescale/enetc/enetc_qos.c +31 -0
@@ -156,6 +156,11 @@ int enetc_setup_tc_taprio(struct net_device *ndev, void *type_data)int err;int i; +/* TSD and Qbv are mutually exclusive in hardware */ +for (i =0 ; i < priv->num_tx_rings; i++) +if (priv->tx_ring[i]->tsd_enable) +return -EBUSY ; +for (i =0 ; i < priv->num_tx_rings; i++) enetc_set_bdr_prio(&priv->si->hw, priv->tx_ring[i]->index,
@@ -297,3 +302,29 @@ int enetc_setup_tc_cbs(struct net_device *ndev, void *type_data)return 0 ; } + +int enetc_setup_tc_txtime (struct net_device *ndev,void *type_data) +{ +struct enetc_ndev_priv *priv =netdev_priv (ndev); +struct tc_etf_qopt_offload *qopt = type_data; +u8 tc_nums =netdev_get_num_tc (ndev); +int tc; + +if (!tc_nums) +return -EOPNOTSUPP ; + + tc = qopt->queue; + +if (tc <0 || tc > priv->num_tx_rings) +return -EINVAL ; + +/* TSD and Qbv are mutually exclusive in hardware */ +if (enetc_rd (&priv->si->hw,ENETC_QBV_PTGCR_OFFSET ) &ENETC_QBV_TGE ) +return -EBUSY ; + + priv->tx_ring[tc]->tsd_enable = qopt->enable; +enetc_port_wr (&priv->si->hw,ENETC_PTCTSDR (tc), + qopt->enable ?ENETC_TSDE :0 ); + +return 0 ; +}
Signature · 1 line
2.17.1
David Miller
maintainerFrom: Po Liu <[email protected]>
Date: Mon, 23 Dec 2019 03:42:39 +0000
Quoted 2 lines
- Transmit checksum offloads and time specific departure operation are mutually exclusive.
I do not see anything which enforces this conflict.
It looks to me like if the user configures time specific departure, and TX SKBs will be checksum offloaded, the time specific departure will simply not be performed.
If true, this behavior will be very surprising for the user.
Instead, the configuration operation that creates the conflict should throw and error and fail.
Thank you.
Br,
Po Liu
Quoted 24 lines
-----Original Message-----
From: David Miller <[email protected]>
Sent: 2019年12月27日 7:10
To: Po Liu <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; Claudiu Manoil <[email protected]>; Vladimir Oltean <[email protected]>; Alexandru Marginean <[email protected]>; Xiaoliang Yang <[email protected]>; Roy Zang <[email protected]>; Mingkai Hu <[email protected]>; Jerry Huang <[email protected]>; Leo Li <[email protected]>; [email protected]
Subject: [EXT] Re: [net-next] enetc: add support time specific departure base on the qos etfCaution: EXT Email
From: Po Liu <[email protected]>
Date: Mon, 23 Dec 2019 03:42:39 +0000Quoted 2 lines
- Transmit checksum offloads and time specific departure operation are mutually exclusive.
I do not see anything which enforces this conflict.
Quoted 7 lines
It looks to me like if the user configures time specific departure, and TX SKBs will be checksum offloaded, the time specific departure will simply not be performed.
If true, this behavior will be very surprising for the user.
Instead, the configuration operation that creates the conflict should throw and error and fail.
I would fix it.
Quoted 2 lines
Thank you.
PATCH v2 1/1 enetc: add support time specific departure base on the qos etf
In reply to Po LiuENETC implement time specific departure capability, which enables the user to specify when a frame can be transmitted. When this capability is enabled, the device will delay the transmission of the frame so that it can be transmitted at the precisely specified time. The delay departure time up to 0.5 seconds in the future. If the departure time in the transmit BD has not yet been reached, based on the current time, the packet will not be transmitted.
This driver was loaded by Qos driver ETF. User could load it by tc commands. Here are the example commands:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 etf \
clockid CLOCK_TAI delta 30000 offload
These example try to set queue mapping first and then set queue 7 with 30us ahead dequeue time.
Then user send test frame should set SO_TXTIME feature for socket.
There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure operation are mutually exclusive.
---
changes log:
v2:
- fix the csum and time specific deaprture return directly if both offloading enabled
drivers/net/ethernet/freescale/enetc/enetc.c | 18 +++++++++++ drivers/net/ethernet/freescale/enetc/enetc.h | 3 ++ .../net/ethernet/freescale/enetc/enetc_hw.h | 10 +++++- .../net/ethernet/freescale/enetc/enetc_qos.c | 31 +++++++++++++++++++ 4 files changed, 61 insertions(+), 1 deletion(-)
drivers/net/ethernet/freescale/enetc/enetc.c +18 -0
@@ -149,11 +149,27 @@ static int enetc_map_tx_buffs(struct enetc_bdr *tx_ring, struct sk_buff *skb,if (enetc_tx_csum (skb, &temp_bd)) flags |=ENETC_TXBD_FLAGS_CSUM |ENETC_TXBD_FLAGS_L4CS ; +if (tx_ring->tsd_enable) + flags |=ENETC_TXBD_FLAGS_TSE |ENETC_TXBD_FLAGS_TXSTART ; + +if (flags &ENETC_TXBD_FLAGS_TSE && flags &ENETC_TXBD_FLAGS_CSUM ) { +dev_err (tx_ring->dev, +"Both TXSTART and CSUM enabled not support!" ); +return 0 ; + }/* first BD needs frm_len and offload flags set */ temp_bd.frm_len =cpu_to_le16 (skb->len); temp_bd.flags = flags; +if (flags &ENETC_TXBD_FLAGS_TSE ) { +u32 temp; + + temp = (skb->skb_mstamp_ns >>5 &ENETC_TXBD_TXSTART_MASK ) + | (flags <<ENETC_TXBD_FLAGS_OFFSET ); + temp_bd.txstart =cpu_to_le32 (temp); + } +if (flags &ENETC_TXBD_FLAGS_EX ) {u8 e_flags =0 ; *txbd = temp_bd;
@@ -1505,6 +1521,8 @@ int enetc_setup_tc(struct net_device *ndev, enum tc_setup_type type,return enetc_setup_tc_taprio (ndev, type_data);case TC_SETUP_QDISC_CBS :return enetc_setup_tc_cbs (ndev, type_data); +case TC_SETUP_QDISC_ETF : +return enetc_setup_tc_txtime (ndev, type_data);default :return -EOPNOTSUPP ; }
drivers/net/ethernet/freescale/enetc/enetc.h +3 -0
@@ -72,6 +72,7 @@ struct enetc_bdr {struct enetc_ring_stats stats;dma_addr_t bd_dma_base; +u8 tsd_enable;/* Time specific departure */ }____cacheline_aligned_in_smp ;static inline void enetc_bdr_idx_inc (struct enetc_bdr *bdr,int *i)
@@ -256,8 +257,10 @@ int enetc_send_cmd(struct enetc_si *si, struct enetc_cbd *cbd);int enetc_setup_tc_taprio (struct net_device *ndev,void *type_data);void enetc_sched_speed_set (struct net_device *ndev);int enetc_setup_tc_cbs (struct net_device *ndev,void *type_data); +int enetc_setup_tc_txtime (struct net_device *ndev,void *type_data);#else #define enetc_setup_tc_taprio (ndev, type_data) -EOPNOTSUPP#define enetc_sched_speed_set (ndev) (void)0#define enetc_setup_tc_cbs (ndev, type_data) -EOPNOTSUPP +#define enetc_setup_tc_txtime (ndev, type_data) -EOPNOTSUPP#endif
drivers/net/ethernet/freescale/enetc/enetc_hw.h +9 -1
@@ -358,6 +358,7 @@ union enetc_tx_bd {u8 l4_csoff;u8 flags; };/* default layout */ +__le32 txstart;__le32 lstatus; }; };
@@ -378,11 +379,14 @@ union enetc_tx_bd { };#define ENETC_TXBD_FLAGS_L4CS BIT(0) +#define ENETC_TXBD_FLAGS_TSE BIT(1)#define ENETC_TXBD_FLAGS_W BIT(2)#define ENETC_TXBD_FLAGS_CSUM BIT(3) +#define ENETC_TXBD_FLAGS_TXSTART BIT(4)#define ENETC_TXBD_FLAGS_EX BIT(6)#define ENETC_TXBD_FLAGS_F BIT(7) - +#define ENETC_TXBD_TXSTART_MASK GENMASK(24, 0) +#define ENETC_TXBD_FLAGS_OFFSET 24static inline void enetc_clear_tx_bd (union enetc_tx_bd *txbd) {memset (txbd,0 ,sizeof (*txbd));
@@ -615,3 +619,7 @@ struct enetc_cbd {/* Port time gating capability register */ #define ENETC_QBV_PTGCAPR_OFFSET 0x11a08#define ENETC_QBV_MAX_GCL_LEN_MASK GENMASK(15, 0) + +/* Port time specific departure */ +#define ENETC_PTCTSDR (n) (0x1210 + 4 * (n)) +#define ENETC_TSDE BIT(31)
drivers/net/ethernet/freescale/enetc/enetc_qos.c +31 -0
@@ -156,6 +156,11 @@ int enetc_setup_tc_taprio(struct net_device *ndev, void *type_data)int err;int i; +/* TSD and Qbv are mutually exclusive in hardware */ +for (i =0 ; i < priv->num_tx_rings; i++) +if (priv->tx_ring[i]->tsd_enable) +return -EBUSY ; +for (i =0 ; i < priv->num_tx_rings; i++) enetc_set_bdr_prio(&priv->si->hw, priv->tx_ring[i]->index,
@@ -297,3 +302,29 @@ int enetc_setup_tc_cbs(struct net_device *ndev, void *type_data)return 0 ; } + +int enetc_setup_tc_txtime (struct net_device *ndev,void *type_data) +{ +struct enetc_ndev_priv *priv =netdev_priv (ndev); +struct tc_etf_qopt_offload *qopt = type_data; +u8 tc_nums =netdev_get_num_tc (ndev); +int tc; + +if (!tc_nums) +return -EOPNOTSUPP ; + + tc = qopt->queue; + +if (tc <0 || tc > priv->num_tx_rings) +return -EINVAL ; + +/* TSD and Qbv are mutually exclusive in hardware */ +if (enetc_rd (&priv->si->hw,ENETC_QBV_PTGCR_OFFSET ) &ENETC_QBV_TGE ) +return -EBUSY ; + + priv->tx_ring[tc]->tsd_enable = qopt->enable; +enetc_port_wr (&priv->si->hw,ENETC_PTCTSDR (tc), + qopt->enable ?ENETC_TSDE :0 ); + +return 0 ; +}
Signature · 1 line
2.17.1
David Miller
maintainerFrom: Po Liu <[email protected]>
Date: Fri, 27 Dec 2019 03:12:18 +0000
Quoted 3 lines
v2:
- fix the csum and time specific deaprture return directly if both offloading enabled
The test is in the wrong location.
You are testing at run time when packets are being transmitted.
Instead, you should test when the configuration change is made which creates the conflict, and disallow the configuration change in such a conflicting case.
Quoted 24 lines
-----Original Message-----
From: David Miller <[email protected]>
Sent: 2019年12月31日 12:27
To: Po Liu <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; Claudiu Manoil <[email protected]>; Vladimir Oltean <[email protected]>; Alexandru Marginean <[email protected]>; Xiaoliang Yang <[email protected]>; Roy Zang <[email protected]>; Mingkai Hu <[email protected]>; Jerry Huang <[email protected]>; Leo Li <[email protected]>; [email protected]
Subject: [EXT] Re: [v2,net-next] enetc: add support time specific departure base on the qos etfCaution: EXT Email
From: Po Liu <[email protected]>
Date: Fri, 27 Dec 2019 03:12:18 +0000Quoted 3 lines
v2:
- fix the csum and time specific deaprture return directly if both offloading enabled
Quoted 6 lines
The test is in the wrong location.
You are testing at run time when packets are being transmitted.
Instead, you should test when the configuration change is made which creates the conflict, and disallow the configuration change in such a conflicting case.
Ok, thanks!
Br,
Po Liu
PATCH v3 1/1 enetc: add support time specific departure base on the qos etf
In reply to Po LiuENETC implement time specific departure capability, which enables the user to specify when a frame can be transmitted. When this capability is enabled, the device will delay the transmission of the frame so that it can be transmitted at the precisely specified time. The delay departure time up to 0.5 seconds in the future. If the departure time in the transmit BD has not yet been reached, based on the current time, the packet will not be transmitted.
This driver was loaded by Qos driver ETF. User could load it by tc commands. Here are the example commands:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 etf \
clockid CLOCK_TAI delta 30000 offload
These example try to set queue mapping first and then set queue 7 with 30us ahead dequeue time.
Then user send test frame should set SO_TXTIME feature for socket.
There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure operation are mutually exclusive.
---
Changes v2-v3:
- Avoid tx checking sum offload when setting TXTIME offload. This is not support in hardware.
drivers/net/ethernet/freescale/enetc/enetc.c | 12 +++++++ drivers/net/ethernet/freescale/enetc/enetc.h | 3 ++ .../net/ethernet/freescale/enetc/enetc_hw.h | 10 +++++- .../net/ethernet/freescale/enetc/enetc_qos.c | 35 +++++++++++++++++++ 4 files changed, 59 insertions(+), 1 deletion(-)
drivers/net/ethernet/freescale/enetc/enetc.c +12 -0
@@ -149,11 +149,21 @@ static int enetc_map_tx_buffs(struct enetc_bdr *tx_ring, struct sk_buff *skb,if (enetc_tx_csum (skb, &temp_bd)) flags |=ENETC_TXBD_FLAGS_CSUM |ENETC_TXBD_FLAGS_L4CS ; +else if (tx_ring->tsd_enable) + flags |=ENETC_TXBD_FLAGS_TSE |ENETC_TXBD_FLAGS_TXSTART ;/* first BD needs frm_len and offload flags set */ temp_bd.frm_len =cpu_to_le16 (skb->len); temp_bd.flags = flags; +if (flags &ENETC_TXBD_FLAGS_TSE ) { +u32 temp; + + temp = (skb->skb_mstamp_ns >>5 &ENETC_TXBD_TXSTART_MASK ) + | (flags <<ENETC_TXBD_FLAGS_OFFSET ); + temp_bd.txstart =cpu_to_le32 (temp); + } +if (flags &ENETC_TXBD_FLAGS_EX ) {u8 e_flags =0 ; *txbd = temp_bd;
@@ -1505,6 +1515,8 @@ int enetc_setup_tc(struct net_device *ndev, enum tc_setup_type type,return enetc_setup_tc_taprio (ndev, type_data);case TC_SETUP_QDISC_CBS :return enetc_setup_tc_cbs (ndev, type_data); +case TC_SETUP_QDISC_ETF : +return enetc_setup_tc_txtime (ndev, type_data);default :return -EOPNOTSUPP ; }
drivers/net/ethernet/freescale/enetc/enetc.h +3 -0
@@ -72,6 +72,7 @@ struct enetc_bdr {struct enetc_ring_stats stats;dma_addr_t bd_dma_base; +u8 tsd_enable;/* Time specific departure */ }____cacheline_aligned_in_smp ;static inline void enetc_bdr_idx_inc (struct enetc_bdr *bdr,int *i)
@@ -256,8 +257,10 @@ int enetc_send_cmd(struct enetc_si *si, struct enetc_cbd *cbd);int enetc_setup_tc_taprio (struct net_device *ndev,void *type_data);void enetc_sched_speed_set (struct net_device *ndev);int enetc_setup_tc_cbs (struct net_device *ndev,void *type_data); +int enetc_setup_tc_txtime (struct net_device *ndev,void *type_data);#else #define enetc_setup_tc_taprio (ndev, type_data) -EOPNOTSUPP#define enetc_sched_speed_set (ndev) (void)0#define enetc_setup_tc_cbs (ndev, type_data) -EOPNOTSUPP +#define enetc_setup_tc_txtime (ndev, type_data) -EOPNOTSUPP#endif
drivers/net/ethernet/freescale/enetc/enetc_hw.h +9 -1
@@ -358,6 +358,7 @@ union enetc_tx_bd {u8 l4_csoff;u8 flags; };/* default layout */ +__le32 txstart;__le32 lstatus; }; };
@@ -378,11 +379,14 @@ union enetc_tx_bd { };#define ENETC_TXBD_FLAGS_L4CS BIT(0) +#define ENETC_TXBD_FLAGS_TSE BIT(1)#define ENETC_TXBD_FLAGS_W BIT(2)#define ENETC_TXBD_FLAGS_CSUM BIT(3) +#define ENETC_TXBD_FLAGS_TXSTART BIT(4)#define ENETC_TXBD_FLAGS_EX BIT(6)#define ENETC_TXBD_FLAGS_F BIT(7) - +#define ENETC_TXBD_TXSTART_MASK GENMASK(24, 0) +#define ENETC_TXBD_FLAGS_OFFSET 24static inline void enetc_clear_tx_bd (union enetc_tx_bd *txbd) {memset (txbd,0 ,sizeof (*txbd));
@@ -615,3 +619,7 @@ struct enetc_cbd {/* Port time gating capability register */ #define ENETC_QBV_PTGCAPR_OFFSET 0x11a08#define ENETC_QBV_MAX_GCL_LEN_MASK GENMASK(15, 0) + +/* Port time specific departure */ +#define ENETC_PTCTSDR (n) (0x1210 + 4 * (n)) +#define ENETC_TSDE BIT(31)
drivers/net/ethernet/freescale/enetc/enetc_qos.c +35 -0
@@ -156,6 +156,11 @@ int enetc_setup_tc_taprio(struct net_device *ndev, void *type_data)int err;int i; +/* TSD and Qbv are mutually exclusive in hardware */ +for (i =0 ; i < priv->num_tx_rings; i++) +if (priv->tx_ring[i]->tsd_enable) +return -EBUSY ; +for (i =0 ; i < priv->num_tx_rings; i++) enetc_set_bdr_prio(&priv->si->hw, priv->tx_ring[i]->index,
@@ -297,3 +302,33 @@ int enetc_setup_tc_cbs(struct net_device *ndev, void *type_data)return 0 ; } + +int enetc_setup_tc_txtime (struct net_device *ndev,void *type_data) +{ +struct enetc_ndev_priv *priv =netdev_priv (ndev); +struct tc_etf_qopt_offload *qopt = type_data; +u8 tc_nums =netdev_get_num_tc (ndev); +int tc; + +if (!tc_nums) +return -EOPNOTSUPP ; + + tc = qopt->queue; + +if (tc <0 || tc > priv->num_tx_rings) +return -EINVAL ; + +/* Do not support TXSTART and TX CSUM offload simutaniously */ +if (ndev->features &NETIF_F_CSUM_MASK ) +return -EBUSY ; + +/* TSD and Qbv are mutually exclusive in hardware */ +if (enetc_rd (&priv->si->hw,ENETC_QBV_PTGCR_OFFSET ) &ENETC_QBV_TGE ) +return -EBUSY ; + + priv->tx_ring[tc]->tsd_enable = qopt->enable; +enetc_port_wr (&priv->si->hw,ENETC_PTCTSDR (tc), + qopt->enable ?ENETC_TSDE :0 ); + +return 0 ; +}
Signature · 1 line
2.17.1
David Miller
maintainerFrom: Po Liu <[email protected]>
Date: Thu, 2 Jan 2020 04:59:24 +0000
Quoted 27 lines
ENETC implement time specific departure capability, which enables the user to specify when a frame can be transmitted. When this capability is enabled, the device will delay the transmission of the frame so that it can be transmitted at the precisely specified time. The delay departure time up to 0.5 seconds in the future. If the departure time in the transmit BD has not yet been reached, based on the current time, the packet will not be transmitted.
This driver was loaded by Qos driver ETF. User could load it by tc commands. Here are the example commands:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1tc qdisc replace dev eth0 parent 1:8 etf \
clockidCLOCK_TAIdelta 30000 offloadThese example try to set queue mapping first and then set queue 7 with 30us ahead dequeue time.
Then user send test frame should set
SO_TXTIMEfeature for socket.There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure operation are mutually exclusive.
Quoted 6 lines
Signed-off-by Po Liu <[email protected]>Reviewed-by Vladimir Oltean <[email protected]>---
Changes v2-v3:
- Avoid tx checking sum offload when setting TXTIME offload. This is not support in hardware.
This looks a lot better, applied, thank you.