combine bindings for simple panels in a few files
Subsystems (4)
v2 cover combine bindings for simple panels in a few files
This patchset introduces two files:
panel-simple.yaml
panel-simple-dsi.yaml
The two files will be used for bindings for simple panels that have only a single power-supply.
For now only a few bindings are migrated - the reamining bindings will be migrated when we have agreed on the format.
v2:
- updated binding description in panel-simple.yaml
- fixed exampe in panel-simple.yaml
(I was missing libyaml-dev - now the examples are checked properly here)
- added panel-simple-dsi.yaml
Sam
Sam Ravnborg (2):
dt-bindings: one binding file for all simple panels
dt-bindings: one file of all simple DSI panels
.../display/panel/ampire,am-480272h3tmqw-t01h.yaml | 42 -------------- .../display/panel/ampire,am800480r3tmqwa1h.txt | 7 --- .../display/panel/panasonic,vvx10f034n00.txt | 20 ------- .../bindings/display/panel/panel-simple-dsi.yaml | 67 ++++++++++++++++++++++ .../bindings/display/panel/panel-simple.yaml | 59 +++++++++++++++++++ 5 files changed, 126 insertions(+), 69 deletions(-)
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH v2 1/2 dt-bindings: one binding file for all simple panels
There is an increasing number of new simple panels. Common for many of these simple panels are that they have one mandatory power-supply and some of them have backlight and / or an enable gpio.
The binding file to describe these panels adds overhead that really do not add value.
The binding are known and there is nothing gained from a dedicated binding file nor for any dedicated example.
The following patch introduces a single panel-simple.yaml and converts two ampire bindings over to the new file.
The conversion - if applied will have following effects:
- The maintainer for the individual file will change
There is no need for many different maintainers for a simple binding. We have the same situation with the panel-simple driver in the kernel.
- The license will change to (GPL-2.0-only OR BSD-2-Clause) There is usually only a single line copied from the original file, a line that is often copied from a datasheet. This license change should be acceptable considered what little is copied.
If the license change is not OK we can use a dedicated binding file in these cases.
This is a follow-up on Rob's big patch converting a lot of panel bindings to individual files:
"dt-bindings: display: Convert a bunch of panels to DT schema"
https://patchwork.ozlabs.org/patch/1197683/
The objectives with one file for the relevant simple panels are:
- Make it simpler to add bindings for simple panels
- Keep the number of bindings file lower and thus easier to find a relevant file to copy from when adding new panels.
- Keep the binding documentation for simple panels more consistent
- Make it simpler to add support for new panels
v2:
- spelling fixes (imirkin via irc, Rob)
- updated description (Rob)
- list properires in alphabetical order
- added power-supply to example (Rob)
- updated title
- reworded changelog a little
--- .../panel/ampire,am-480272h3tmqw-t01h.yaml | 42 ------------- .../panel/ampire,am800480r3tmqwa1h.txt | 7 --- .../bindings/display/panel/panel-simple.yaml | 59 +++++++++++++++++++ 3 files changed, 59 insertions(+), 49 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am800480r3tmqwa1h.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-simple.yaml
Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml deleted +0 -42
@@ -1,42 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/display/panel/ampire,am-480272h3tmqw-t01h.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel - -maintainers: - - Yannick Fertre <[email protected]> - - Thierry Reding <[email protected]> - -allOf: - - $ref: panel-common.yaml# - -properties: - compatible: - const: ampire,am-480272h3tmqw-t01h - - power-supply: true - enable-gpios: true - backlight: true - port: true - -required: - - compatible - -additionalProperties: false - -examples: - - | - panel_rgb: panel { - compatible = "ampire,am-480272h3tmqw-t01h"; - enable-gpios = <&gpioa 8 1>; - port { - panel_in_rgb: endpoint { - remote-endpoint = <&controller_out_rgb>; - }; - }; - }; - -...
Documentation/devicetree/bindings/display/panel/ampire,am800480r3tmqwa1h.txt deleted +0 -7
@@ -1,7 +0,0 @@ -Ampire AM-800480R3TMQW-A1H 7.0" WVGA TFT LCD panel - -Required properties: -- compatible: should be "ampire,am800480r3tmqwa1h" - -This binding is compatible with the simple-panel binding, which is specified -in simple-panel.txt in this directory.
Documentation/devicetree/bindings/display/panel/panel-simple.yaml new file +59 -0
59 lines not on this page · raw message
Signature · 6 lines
2.20.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 1/2] dt-bindings: one binding file for all simple panels
Quoted 170 lines · Sam Ravnborg
There is an increasing number of new simple panels. Common for many of these simple panels are that they have one mandatory power-supply and some of them have backlight and / or an enable gpio.
The binding file to describe these panels adds overhead that really do not add value.
The binding are known and there is nothing gained from a dedicated binding file nor for any dedicated example.The following patch introduces a single
panel-simple.yamland converts two ampire bindings over to the new file.The conversion - if applied will have following effects:
- The maintainer for the individual file will change
There is no need for many different maintainers for a simple binding. We have the same situation with the panel-simple driver in the kernel.- The license will change to (GPL-2.0-only OR BSD-2-Clause) There is usually only a single line copied from the original file, a line that is often copied from a datasheet. This license change should be acceptable considered what little is copied.
If the license change is not OK we can use a dedicated binding file in these cases.This is a follow-up on Rob's big patch converting a lot of panel bindings to individual files:
"dt-bindings: display: Convert a bunch of panels to DT schema"
https://patchwork.ozlabs.org/patch/1197683/The objectives with one file for the relevant simple panels are:
- Make it simpler to add bindings for simple panels
- Keep the number of bindings file lower and thus easier to find a relevant file to copy from when adding new panels.
- Keep the binding documentation for simple panels more consistent
- Make it simpler to add support for new panelsv2:
- spelling fixes (imirkin via irc, Rob)
- updated description (Rob)
- list properires in alphabetical order
- added power-supply to example (Rob)
- updated title
- reworded changelog a littleSigned-off-by Sam Ravnborg <[email protected]>Cc Thierry Reding <[email protected]>Cc Rob Herring <[email protected]>Cc Maxime Ripard <[email protected]>Cc Yannick Fertre <[email protected]>Cc Mark Rutland <[email protected]>Cc Daniel Vetter <[email protected]>--- .../panel/ampire,am-480272h3tmqw-t01h.yaml | 42 ------------- .../panel/ampire,am800480r3tmqwa1h.txt | 7 --- .../bindings/display/panel/panel-simple.yaml | 59 +++++++++++++++++++ 3 files changed, 59 insertions(+), 49 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am800480r3tmqwa1h.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-simple.yamlDocumentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml deleted +0
-42@@ -1,42 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/display/panel/ampire,am-480272h3tmqw-t01h.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel - -maintainers: - - Yannick Fertre <[email protected]> - - Thierry Reding <[email protected]> - -allOf: - - $ref: panel-common.yaml# - -properties: - compatible: - const: ampire,am-480272h3tmqw-t01h - - power-supply: true - enable-gpios: true - backlight: true - port: true - -required: - - compatible - -additionalProperties: false - -examples: - - | - panel_rgb: panel { - compatible = "ampire,am-480272h3tmqw-t01h"; - enable-gpios = <&gpioa 8 1>; - port { - panel_in_rgb: endpoint { - remote-endpoint = <&controller_out_rgb>; - }; - }; - }; - -...Documentation/devicetree/bindings/display/panel/ampire,am800480r3tmqwa1h.txt deleted +0
-7@@ -1,7 +0,0 @@ -Ampire AM-800480R3TMQW-A1H 7.0" WVGA TFT LCD panel - -Required properties: -- compatible: should be "ampire,am800480r3tmqwa1h" - -This binding is compatible with the simple-panel binding, which is specified -in simple-panel.txt in this directory.Documentation/devicetree/bindings/display/panel/panel-simple.yaml new file +36
-0@@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-simple.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Simple panels with one power supply + +maintainers: + - Thierry Reding <[email protected]> + - Sam Ravnborg <[email protected]> + +description: | + This binding file is a collection of the simple (dumb) panels that + requires only a single power-supply. + There are optionally a backlight and an enable GPIO. + The panel may use an OF graph binding for the association to the display, + or it may be a direct child node of the display. + + If the panel is more advanced a dedicated binding file is required. + +allOf: + - $ref: panel-common.yaml# + +properties: + + compatible: + enum: + # compatible must be listed in alphabetical order, ordered by compatible. + # The description in the comment is mandatory for each compatible. + + # Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel + - ampire,am-480272h3tmqw-t01h + # Ampire AM-800480R3TMQW-A1H 7.0" WVGA TFT LCD panel + - ampire,am800480r3tmqwa1h +
Documentation/devicetree/bindings/display/panel/panel-simple.yaml line 46
Quoted 10 lines
Documentation/devicetree/bindings/display/panel/panel-simple.yaml new file +10
-0+ backlight: true + enable-gpios: true + port: true + power-supply: true + +additionalProperties: false + +required: + - compatible + - power-supply
Hi Sam,
power-supply property should be optional like it was in ampire,am-480272h3tmqw-t01h.yaml
else it looks good for me.
Benjamin
Quoted 16 lines
Documentation/devicetree/bindings/display/panel/panel-simple.yaml new file +13
-1+ +examples: + - | + panel_rgb: panel-rgb { + compatible = "ampire,am-480272h3tmqw-t01h"; + power-supply = <&vcc_lcd_reg>; + + port { + panel_in_rgb: endpoint { + remote-endpoint = <<dc_out_rgb>; + }; + }; + }; --2.20.1
Quoted 4 lines
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 1/2] dt-bindings: one binding file for all simple panels
Hi Benjamin.
Quoted 10 lines
Documentation/devicetree/bindings/display/panel/panel-simple.yaml line 46
Quoted 4 lines
Documentation/devicetree/bindings/display/panel/panel-simple.yaml new file +4
-0+ +required: + - compatible + - power-supplyHi Sam,
power-supply property should be optional like it was in ampire,am-480272h3tmqw-t01h.yaml
else it looks good for me.
power-supply was discussed in PATRCH 2/2 and the conclusion was that power-supply is required.
Thus I take this as an Acked-by:
And I have committed to drm-misc-next
Sam
Re: [PATCH v2 1/2] dt-bindings: one binding file for all simple panels
In reply to Sam RavnborgQuoted 58 lines · Sam Ravnborg
There is an increasing number of new simple panels. Common for many of these simple panels are that they have one mandatory power-supply and some of them have backlight and / or an enable gpio.
The binding file to describe these panels adds overhead that really do not add value.
The binding are known and there is nothing gained from a dedicated binding file nor for any dedicated example.The following patch introduces a single
panel-simple.yamland converts two ampire bindings over to the new file.The conversion - if applied will have following effects:
- The maintainer for the individual file will change
There is no need for many different maintainers for a simple binding. We have the same situation with the panel-simple driver in the kernel.- The license will change to (GPL-2.0-only OR BSD-2-Clause) There is usually only a single line copied from the original file, a line that is often copied from a datasheet. This license change should be acceptable considered what little is copied.
If the license change is not OK we can use a dedicated binding file in these cases.This is a follow-up on Rob's big patch converting a lot of panel bindings to individual files:
"dt-bindings: display: Convert a bunch of panels to DT schema"
https://patchwork.ozlabs.org/patch/1197683/The objectives with one file for the relevant simple panels are:
- Make it simpler to add bindings for simple panels
- Keep the number of bindings file lower and thus easier to find a relevant file to copy from when adding new panels.
- Keep the binding documentation for simple panels more consistent
- Make it simpler to add support for new panelsv2:
- spelling fixes (imirkin via irc, Rob)
- updated description (Rob)
- list properires in alphabetical order
- added power-supply to example (Rob)
- updated title
- reworded changelog a littleSigned-off-by Sam Ravnborg <[email protected]>Cc Thierry Reding <[email protected]>Cc Rob Herring <[email protected]>Cc Maxime Ripard <[email protected]>Cc Yannick Fertre <[email protected]>Cc Mark Rutland <[email protected]>Cc Daniel Vetter <[email protected]>
Quoted 8 lines
--- .../panel/ampire,am-480272h3tmqw-t01h.yaml | 42 ------------- .../panel/ampire,am800480r3tmqwa1h.txt | 7 --- .../bindings/display/panel/panel-simple.yaml | 59 +++++++++++++++++++ 3 files changed, 59 insertions(+), 49 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am800480r3tmqwa1h.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-simple.yaml
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 1/2] dt-bindings: one binding file for all simple panels
In reply to Sam RavnborgHi Jyri, Rob, Paul, Miquel.
Following patch is now applied to drm-misc-next.
Please add your simple panels to this file so we avoid independent bindings files for ecah panel.
I will handle the inevitable conflicts when I apply.
Sam
Quoted 194 lines · Sam Ravnborg
There is an increasing number of new simple panels. Common for many of these simple panels are that they have one mandatory power-supply and some of them have backlight and / or an enable gpio.
The binding file to describe these panels adds overhead that really do not add value.
The binding are known and there is nothing gained from a dedicated binding file nor for any dedicated example.The following patch introduces a single
panel-simple.yamland converts two ampire bindings over to the new file.The conversion - if applied will have following effects:
- The maintainer for the individual file will change
There is no need for many different maintainers for a simple binding. We have the same situation with the panel-simple driver in the kernel.- The license will change to (GPL-2.0-only OR BSD-2-Clause) There is usually only a single line copied from the original file, a line that is often copied from a datasheet. This license change should be acceptable considered what little is copied.
If the license change is not OK we can use a dedicated binding file in these cases.This is a follow-up on Rob's big patch converting a lot of panel bindings to individual files:
"dt-bindings: display: Convert a bunch of panels to DT schema"
https://patchwork.ozlabs.org/patch/1197683/The objectives with one file for the relevant simple panels are:
- Make it simpler to add bindings for simple panels
- Keep the number of bindings file lower and thus easier to find a relevant file to copy from when adding new panels.
- Keep the binding documentation for simple panels more consistent
- Make it simpler to add support for new panelsv2:
- spelling fixes (imirkin via irc, Rob)
- updated description (Rob)
- list properires in alphabetical order
- added power-supply to example (Rob)
- updated title
- reworded changelog a littleSigned-off-by Sam Ravnborg <[email protected]>Cc Thierry Reding <[email protected]>Cc Rob Herring <[email protected]>Cc Maxime Ripard <[email protected]>Cc Yannick Fertre <[email protected]>Cc Mark Rutland <[email protected]>Cc Daniel Vetter <[email protected]>--- .../panel/ampire,am-480272h3tmqw-t01h.yaml | 42 ------------- .../panel/ampire,am800480r3tmqwa1h.txt | 7 --- .../bindings/display/panel/panel-simple.yaml | 59 +++++++++++++++++++ 3 files changed, 59 insertions(+), 49 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am800480r3tmqwa1h.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-simple.yamlDocumentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml deleted +0
-42@@ -1,42 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/display/panel/ampire,am-480272h3tmqw-t01h.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel - -maintainers: - - Yannick Fertre <[email protected]> - - Thierry Reding <[email protected]> - -allOf: - - $ref: panel-common.yaml# - -properties: - compatible: - const: ampire,am-480272h3tmqw-t01h - - power-supply: true - enable-gpios: true - backlight: true - port: true - -required: - - compatible - -additionalProperties: false - -examples: - - | - panel_rgb: panel { - compatible = "ampire,am-480272h3tmqw-t01h"; - enable-gpios = <&gpioa 8 1>; - port { - panel_in_rgb: endpoint { - remote-endpoint = <&controller_out_rgb>; - }; - }; - }; - -...Documentation/devicetree/bindings/display/panel/ampire,am800480r3tmqwa1h.txt deleted +0
-7@@ -1,7 +0,0 @@ -Ampire AM-800480R3TMQW-A1H 7.0" WVGA TFT LCD panel - -Required properties: -- compatible: should be "ampire,am800480r3tmqwa1h" - -This binding is compatible with the simple-panel binding, which is specified -in simple-panel.txt in this directory.Documentation/devicetree/bindings/display/panel/panel-simple.yaml new file +59
-0@@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-simple.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Simple panels with one power supply + +maintainers: + - Thierry Reding <[email protected]> + - Sam Ravnborg <[email protected]> + +description: | + This binding file is a collection of the simple (dumb) panels that + requires only a single power-supply. + There are optionally a backlight and an enable GPIO. + The panel may use an OF graph binding for the association to the display, + or it may be a direct child node of the display. + + If the panel is more advanced a dedicated binding file is required. + +allOf: + - $ref: panel-common.yaml# + +properties: + + compatible: + enum: + # compatible must be listed in alphabetical order, ordered by compatible. + # The description in the comment is mandatory for each compatible. + + # Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel + - ampire,am-480272h3tmqw-t01h + # Ampire AM-800480R3TMQW-A1H 7.0" WVGA TFT LCD panel + - ampire,am800480r3tmqwa1h + + backlight: true + enable-gpios: true + port: true + power-supply: true + +additionalProperties: false + +required: + - compatible + - power-supply + +examples: + - | + panel_rgb: panel-rgb { + compatible = "ampire,am-480272h3tmqw-t01h"; + power-supply = <&vcc_lcd_reg>; + + port { + panel_in_rgb: endpoint { + remote-endpoint = <<dc_out_rgb>; + }; + }; + };Signature · 1 line
2.20.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH v2 2/2 dt-bindings: one file of all simple DSI panels
In reply to Sam RavnborgTo complement panel-simple.yaml, create panel-simple-dsi.yaml. panel-simple-dsi-yaml are for all simple DSP panels with a single power-supply and optional backlight / enable GPIO.
Migrate panasonic,vvx10f034n00 over to the new file.
The objectives with one file for all the simple DSI panels are:
- Make it simpler to add bindings for simple DSI panels
- Keep the number of bindings file lower
- Keep the binding documentation for simple DSI panels more consistent
--- .../display/panel/panasonic,vvx10f034n00.txt | 20 ------ .../display/panel/panel-simple-dsi.yaml | 67 +++++++++++++++++++ 2 files changed, 67 insertions(+), 20 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml
Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt deleted +0 -20
@@ -1,20 +0,0 @@ -Panasonic 10" WUXGA TFT LCD panel - -Required properties: -- compatible: should be "panasonic,vvx10f034n00" -- reg: DSI virtual channel of the peripheral -- power-supply: phandle of the regulator that provides the supply voltage - -Optional properties: -- backlight: phandle of the backlight device attached to the panel - -Example: - - mdss_dsi@fd922800 { - panel@0 { - compatible = "panasonic,vvx10f034n00"; - reg = <0>; - power-supply = <&vreg_vsp>; - backlight = <&lp8566_wled>; - }; - };
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +67 -0
67 lines not on this page · raw message
Signature · 6 lines
2.20.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 2/2] dt-bindings: one file of all simple DSI panels
Quoted 83 lines · Sam Ravnborg
To complement
panel-simple.yaml, createpanel-simple-dsi.yaml. panel-simple-dsi-yaml are for all simple DSP panels with a single power-supply and optional backlight / enable GPIO.Migrate panasonic,vvx10f034n00 over to the new file.
The objectives with one file for all the simple DSI panels are:
- Make it simpler to add bindings for simple DSI panels
- Keep the number of bindings file lower
- Keep the binding documentation for simple DSI panels more consistentSigned-off-by Sam Ravnborg <[email protected]>Cc Thierry Reding <[email protected]>Cc Rob Herring <[email protected]>Cc Maxime Ripard <[email protected]>Cc Yannick Fertre <[email protected]>Cc Mark Rutland <[email protected]>Cc Daniel Vetter <[email protected]>--- .../display/panel/panasonic,vvx10f034n00.txt | 20 ------ .../display/panel/panel-simple-dsi.yaml | 67 +++++++++++++++++++ 2 files changed, 67 insertions(+), 20 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yamlDocumentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt deleted +0
-20@@ -1,20 +0,0 @@ -Panasonic 10" WUXGA TFT LCD panel - -Required properties: -- compatible: should be "panasonic,vvx10f034n00" -- reg: DSI virtual channel of the peripheral -- power-supply: phandle of the regulator that provides the supply voltage - -Optional properties: -- backlight: phandle of the backlight device attached to the panel - -Example: - - mdss_dsi@fd922800 { - panel@0 { - compatible = "panasonic,vvx10f034n00"; - reg = <0>; - power-supply = <&vreg_vsp>; - backlight = <&lp8566_wled>; - }; - };Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +23
-0@@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-simple-dsi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Simple DSI panels with a single power-supply + +maintainers: + - Thierry Reding <[email protected]> + - Sam Ravnborg <[email protected]> + +description: | + This binding file is a collection of the DSI panels that + requires only a single power-supply. + There are optionally a backlight and an enable GPIO. + The panel may use an OF graph binding for the association to the display, + or it may be a direct child node of the display. + + If the panel is more advanced a dedicated binding file is required. + +allOf: + - $ref: panel-common.yaml#
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 33
Quoted 10 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +10
-0+ +properties: + + compatible: + enum: + # compatible must be listed in alphabetical order, ordered by compatible. + # The description in the comment is mandatory for each compatible. + + # Panasonic 10" WUXGA TFT LCD panel + - panasonic,vvx10f034n00
Hi Sam,
I have tested your patch with these 2 dsi panels:
# Orise Tech OTM8009A is a 3.97" 480x800 TFT LCD
- orisetech,otm8009a
# Raydium Semiconductor Corporation RM68200 is a 5.5" 720x1280 TFT LCD
- raydium,rm68200
It is close to be fine for me but I have minors comments below.
Benjamin
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 42
Quoted 9 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +9
-0+ + reg: + maxItems: 1 + description: DSI virtual channel + + backlight: true + enable-gpios: true + port: true + power-supply: true
add reset-gpios: true to support orisetech panel
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 48
Quoted 6 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +6
-0+ +additionalProperties: false + +required: + - compatible + - power-supply
power-supply should optional
Quoted 26 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +19
-1+ - reg + +examples: + - | + mdss_dsi@fd922800 { + #address-cells = <1>; + #size-cells = <0>; + panel@0 { + compatible = "panasonic,vvx10f034n00"; + reg = <0>; + power-supply = <&vcc_lcd_reg>; + + port { + panel: endpoint { + remote-endpoint = <<dc_out>; + }; + }; + }; + }; --2.20.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Rob Herring
maintainerRe: [PATCH v2 2/2] dt-bindings: one file of all simple DSI panels
Quoted 108 lines · Benjamin Gaignard
Quoted 83 lines · Sam Ravnborg
To complement
panel-simple.yaml, createpanel-simple-dsi.yaml. panel-simple-dsi-yaml are for all simple DSP panels with a single power-supply and optional backlight / enable GPIO.Migrate panasonic,vvx10f034n00 over to the new file.
The objectives with one file for all the simple DSI panels are:
- Make it simpler to add bindings for simple DSI panels
- Keep the number of bindings file lower
- Keep the binding documentation for simple DSI panels more consistentSigned-off-by Sam Ravnborg <[email protected]>Cc Thierry Reding <[email protected]>Cc Rob Herring <[email protected]>Cc Maxime Ripard <[email protected]>Cc Yannick Fertre <[email protected]>Cc Mark Rutland <[email protected]>Cc Daniel Vetter <[email protected]>--- .../display/panel/panasonic,vvx10f034n00.txt | 20 ------ .../display/panel/panel-simple-dsi.yaml | 67 +++++++++++++++++++ 2 files changed, 67 insertions(+), 20 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yamlDocumentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt deleted +0
-20@@ -1,20 +0,0 @@ -Panasonic 10" WUXGA TFT LCD panel - -Required properties: -- compatible: should be "panasonic,vvx10f034n00" -- reg: DSI virtual channel of the peripheral -- power-supply: phandle of the regulator that provides the supply voltage - -Optional properties: -- backlight: phandle of the backlight device attached to the panel - -Example: - - mdss_dsi@fd922800 { - panel@0 { - compatible = "panasonic,vvx10f034n00"; - reg = <0>; - power-supply = <&vreg_vsp>; - backlight = <&lp8566_wled>; - }; - };Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +23
-0@@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-simple-dsi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Simple DSI panels with a single power-supply + +maintainers: + - Thierry Reding <[email protected]> + - Sam Ravnborg <[email protected]> + +description: | + This binding file is a collection of the DSI panels that + requires only a single power-supply. + There are optionally a backlight and an enable GPIO. + The panel may use an OF graph binding for the association to the display, + or it may be a direct child node of the display. + + If the panel is more advanced a dedicated binding file is required. + +allOf: + - $ref: panel-common.yaml#Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 33
Quoted 10 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +10
-0+ +properties: + + compatible: + enum: + # compatible must be listed in alphabetical order, ordered by compatible. + # The description in the comment is mandatory for each compatible. + + # Panasonic 10" WUXGA TFT LCD panel + - panasonic,vvx10f034n00Hi Sam,
I have tested your patch with these 2 dsi panels:
# Orise Tech OTM8009A is a 3.97" 480x800 TFT LCD
- orisetech,otm8009a
# Raydium Semiconductor Corporation RM68200 is a 5.5" 720x1280 TFT LCD
- raydium,rm68200It is close to be fine for me but I have minors comments below.
Benjamin
Quoted 11 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 42
Quoted 9 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +9
-0+ + reg: + maxItems: 1 + description: DSI virtual channel + + backlight: true + enable-gpios: true + port: true + power-supply: trueadd reset-gpios: true to support orisetech panel
Nope. If not a single GPIO and single supply, not a simple panel.
Maybe reset could be allowed, but we have to draw the line somewhere.
Quoted 8 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 48
Quoted 6 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +6
-0+ +additionalProperties: false + +required: + - compatible + - power-supplypower-supply should optional
The panel works without power? The dts should have a fixed supply if not controllable.
Here's the problem. If it is not required, then panels with multiple supplies will get added here because they didn't care to begin with. Then when someone decides to think about the supplies it will have to be moved. Bindings need to be complete from the start.
Rob
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 2/2] dt-bindings: one file of all simple DSI panels
Quoted 136 lines · Rob Herring
Quoted 108 lines · Benjamin Gaignard
Quoted 83 lines · Sam Ravnborg
To complement
panel-simple.yaml, createpanel-simple-dsi.yaml. panel-simple-dsi-yaml are for all simple DSP panels with a single power-supply and optional backlight / enable GPIO.Migrate panasonic,vvx10f034n00 over to the new file.
The objectives with one file for all the simple DSI panels are:
- Make it simpler to add bindings for simple DSI panels
- Keep the number of bindings file lower
- Keep the binding documentation for simple DSI panels more consistentSigned-off-by Sam Ravnborg <[email protected]>Cc Thierry Reding <[email protected]>Cc Rob Herring <[email protected]>Cc Maxime Ripard <[email protected]>Cc Yannick Fertre <[email protected]>Cc Mark Rutland <[email protected]>Cc Daniel Vetter <[email protected]>--- .../display/panel/panasonic,vvx10f034n00.txt | 20 ------ .../display/panel/panel-simple-dsi.yaml | 67 +++++++++++++++++++ 2 files changed, 67 insertions(+), 20 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yamlDocumentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt deleted +0
-20@@ -1,20 +0,0 @@ -Panasonic 10" WUXGA TFT LCD panel - -Required properties: -- compatible: should be "panasonic,vvx10f034n00" -- reg: DSI virtual channel of the peripheral -- power-supply: phandle of the regulator that provides the supply voltage - -Optional properties: -- backlight: phandle of the backlight device attached to the panel - -Example: - - mdss_dsi@fd922800 { - panel@0 { - compatible = "panasonic,vvx10f034n00"; - reg = <0>; - power-supply = <&vreg_vsp>; - backlight = <&lp8566_wled>; - }; - };Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +23
-0@@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-simple-dsi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Simple DSI panels with a single power-supply + +maintainers: + - Thierry Reding <[email protected]> + - Sam Ravnborg <[email protected]> + +description: | + This binding file is a collection of the DSI panels that + requires only a single power-supply. + There are optionally a backlight and an enable GPIO. + The panel may use an OF graph binding for the association to the display, + or it may be a direct child node of the display. + + If the panel is more advanced a dedicated binding file is required. + +allOf: + - $ref: panel-common.yaml#Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 33
Quoted 10 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +10
-0+ +properties: + + compatible: + enum: + # compatible must be listed in alphabetical order, ordered by compatible. + # The description in the comment is mandatory for each compatible. + + # Panasonic 10" WUXGA TFT LCD panel + - panasonic,vvx10f034n00Hi Sam,
I have tested your patch with these 2 dsi panels:
# Orise Tech OTM8009A is a 3.97" 480x800 TFT LCD
- orisetech,otm8009a
# Raydium Semiconductor Corporation RM68200 is a 5.5" 720x1280 TFT LCD
- raydium,rm68200It is close to be fine for me but I have minors comments below.
Benjamin
Quoted 11 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 42
Quoted 9 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +9
-0+ + reg: + maxItems: 1 + description: DSI virtual channel + + backlight: true + enable-gpios: true + port: true + power-supply: trueadd reset-gpios: true to support orisetech panel
Nope. If not a single GPIO and single supply, not a simple panel.
Maybe reset could be allowed, but we have to draw the line somewhere.
Quoted 8 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 48
Quoted 6 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +6
-0+ +additionalProperties: false + +required: + - compatible + - power-supplypower-supply should optional
Quoted 7 lines
The panel works without power? The dts should have a fixed supply if not controllable.
Here's the problem. If it is not required, then panels with multiple supplies will get added here because they didn't care to begin with. Then when someone decides to think about the supplies it will have to be moved. Bindings need to be complete from the start.
Fair enough, I will add fixed supply in dts files.
If reset-gpios could be added in this schema then we could include oristech panel here.
Benjamin
Quoted 2 lines
Rob
Re: [PATCH v2 2/2] dt-bindings: one file of all simple DSI panels
Quoted 141 lines · Benjamin Gaignard
Quoted 139 lines · Rob Herring
Quoted 108 lines · Benjamin Gaignard
Quoted 83 lines · Sam Ravnborg
To complement
panel-simple.yaml, createpanel-simple-dsi.yaml. panel-simple-dsi-yaml are for all simple DSP panels with a single power-supply and optional backlight / enable GPIO.Migrate panasonic,vvx10f034n00 over to the new file.
The objectives with one file for all the simple DSI panels are:
- Make it simpler to add bindings for simple DSI panels
- Keep the number of bindings file lower
- Keep the binding documentation for simple DSI panels more consistentSigned-off-by Sam Ravnborg <[email protected]>Cc Thierry Reding <[email protected]>Cc Rob Herring <[email protected]>Cc Maxime Ripard <[email protected]>Cc Yannick Fertre <[email protected]>Cc Mark Rutland <[email protected]>Cc Daniel Vetter <[email protected]>--- .../display/panel/panasonic,vvx10f034n00.txt | 20 ------ .../display/panel/panel-simple-dsi.yaml | 67 +++++++++++++++++++ 2 files changed, 67 insertions(+), 20 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yamlDocumentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt deleted +0
-20@@ -1,20 +0,0 @@ -Panasonic 10" WUXGA TFT LCD panel - -Required properties: -- compatible: should be "panasonic,vvx10f034n00" -- reg: DSI virtual channel of the peripheral -- power-supply: phandle of the regulator that provides the supply voltage - -Optional properties: -- backlight: phandle of the backlight device attached to the panel - -Example: - - mdss_dsi@fd922800 { - panel@0 { - compatible = "panasonic,vvx10f034n00"; - reg = <0>; - power-supply = <&vreg_vsp>; - backlight = <&lp8566_wled>; - }; - };Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +23
-0@@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-simple-dsi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Simple DSI panels with a single power-supply + +maintainers: + - Thierry Reding <[email protected]> + - Sam Ravnborg <[email protected]> + +description: | + This binding file is a collection of the DSI panels that + requires only a single power-supply. + There are optionally a backlight and an enable GPIO. + The panel may use an OF graph binding for the association to the display, + or it may be a direct child node of the display. + + If the panel is more advanced a dedicated binding file is required. + +allOf: + - $ref: panel-common.yaml#Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 33
Quoted 10 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +10
-0+ +properties: + + compatible: + enum: + # compatible must be listed in alphabetical order, ordered by compatible. + # The description in the comment is mandatory for each compatible. + + # Panasonic 10" WUXGA TFT LCD panel + - panasonic,vvx10f034n00Hi Sam,
I have tested your patch with these 2 dsi panels:
# Orise Tech OTM8009A is a 3.97" 480x800 TFT LCD
- orisetech,otm8009a
# Raydium Semiconductor Corporation RM68200 is a 5.5" 720x1280 TFT LCD
- raydium,rm68200It is close to be fine for me but I have minors comments below.
Benjamin
Quoted 11 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 42
Quoted 9 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +9
-0+ + reg: + maxItems: 1 + description: DSI virtual channel + + backlight: true + enable-gpios: true + port: true + power-supply: trueadd reset-gpios: true to support orisetech panel
Nope. If not a single GPIO and single supply, not a simple panel.
Maybe reset could be allowed, but we have to draw the line somewhere.
Quoted 8 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 48
Quoted 6 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +6
-0+ +additionalProperties: false + +required: + - compatible + - power-supplypower-supply should optional
The panel works without power? The dts should have a fixed supply if not controllable.
Quoted 8 lines
Quoted 4 lines
Here's the problem. If it is not required, then panels with multiple supplies will get added here because they didn't care to begin with. Then when someone decides to think about the supplies it will have to be moved. Bindings need to be complete from the start.
Fair enough, I will add fixed supply in dts files.
If reset-gpios could be added in this schema then we could include oristech panel here.
Does this patch has been merged ?
Regards,
Benjamin
Quoted 5 lines
Benjamin
Quoted 2 lines
Rob
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 2/2] dt-bindings: one file of all simple DSI panels
Hi Benjamin.
Quoted 11 lines
Quoted 9 lines
Quoted 5 lines
Here's the problem. If it is not required, then panels with multiple supplies will get added here because they didn't care to begin with. Then when someone decides to think about the supplies it will have to be moved. Bindings need to be complete from the start.
Fair enough, I will add fixed supply in dts files.
If reset-gpios could be added in this schema then we could include oristech panel here.Does this patch has been merged ?
I was sidetracked by other things.
Maybe you can move it forward?
Sam
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 2/2] dt-bindings: one file of all simple DSI panels
Quoted 8 lines · Sam Ravnborg
Hi Benjamin.
Quoted 6 lines
Quoted 6 lines
Quoted 5 lines
Here's the problem. If it is not required, then panels with multiple supplies will get added here because they didn't care to begin with. Then when someone decides to think about the supplies it will have to be moved. Bindings need to be complete from the start.
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
Fair enough, I will add fixed supply in dts files.
If reset-gpios could be added in this schema then we could include oristech panel here.Does this patch has been merged ?
I was sidetracked by other things.
Maybe you can move it forward?
Yes I will send a v3.
Benjamin
Quoted 2 lines
Sam
Re: [PATCH v2 2/2] dt-bindings: one file of all simple DSI panels
In reply to Sam RavnborgQuoted 21 lines · Sam Ravnborg
To complement
panel-simple.yaml, createpanel-simple-dsi.yaml. panel-simple-dsi-yaml are for all simple DSP panels with a single power-supply and optional backlight / enable GPIO.Migrate panasonic,vvx10f034n00 over to the new file.
The objectives with one file for all the simple DSI panels are:
- Make it simpler to add bindings for simple DSI panels
- Keep the number of bindings file lower
- Keep the binding documentation for simple DSI panels more consistentSigned-off-by Sam Ravnborg <[email protected]>Cc Thierry Reding <[email protected]>Cc Rob Herring <[email protected]>Cc Maxime Ripard <[email protected]>Cc Yannick Fertre <[email protected]>Cc Mark Rutland <[email protected]>Cc Daniel Vetter <[email protected]>
Quoted 6 lines
--- .../display/panel/panasonic,vvx10f034n00.txt | 20 ------ .../display/panel/panel-simple-dsi.yaml | 67 +++++++++++++++++++ 2 files changed, 67 insertions(+), 20 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt create mode 100644 Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml
Quoted 53 lines
Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt deleted +0
-20@@ -1,20 +0,0 @@ -Panasonic 10" WUXGA TFT LCD panel - -Required properties: -- compatible: should be "panasonic,vvx10f034n00" -- reg: DSI virtual channel of the peripheral -- power-supply: phandle of the regulator that provides the supply voltage - -Optional properties: -- backlight: phandle of the backlight device attached to the panel - -Example: - - mdss_dsi@fd922800 { - panel@0 { - compatible = "panasonic,vvx10f034n00"; - reg = <0>; - power-supply = <&vreg_vsp>; - backlight = <&lp8566_wled>; - }; - };Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +20
-0@@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-simple-dsi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Simple DSI panels with a single power-supply + +maintainers: + - Thierry Reding <[email protected]> + - Sam Ravnborg <[email protected]> + +description: | + This binding file is a collection of the DSI panels that + requires only a single power-supply. + There are optionally a backlight and an enable GPIO. + The panel may use an OF graph binding for the association to the display, + or it may be a direct child node of the display. + + If the panel is more advanced a dedicated binding file is required.
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 30
Quoted 10 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +10
-0+ +allOf: + - $ref: panel-common.yaml# + +properties: + + compatible: + enum: + # compatible must be listed in alphabetical order, ordered by compatible. + # The description in the comment is mandatory for each compatible.
To answer your irc question, this is fine. You could do it like this instead:
oneOf:
- description: ...
const: compat-string
- description: ...
const: compat-string-2
The advantage is being able to extract 'description' if say you wanted to generate documentation. Even so, I somewhat prefer how you have it.
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 32
Quoted 2 lines
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +2
-0+ + # Panasonic 10" WUXGA TFT LCD panel
I'd align the # with the string to keep the list '-' a bit more visible. IOW, 2 more spaces (before my next comment).
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml line 33
Quoted 1 line
Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml new file +1
-0+ - panasonic,vvx10f034n00
This should be indented 2 more spaces.
BTW, I extracted all the panels from my patch with this:
git show | grep -E '(title|const)' | sed -e 's/\+title:/ #/' -e 's/+
const:/\-/'
There's a few with more than just 'title'.
Rob
Quoted 24 lines · Sam Ravnborg
This patchset introduces two files:
panel-simple.yaml
panel-simple-dsi.yamlThe two files will be used for bindings for simple panels that have only a single power-supply.
For now only a few bindings are migrated - the reamining bindings will be migrated when we have agreed on the format.
v2:
- updated binding description inpanel-simple.yaml
- fixed exampe inpanel-simple.yaml
(I was missing libyaml-dev - now the examples are checked properly here)
- addedpanel-simple-dsi.yamlSam
Sam Ravnborg (2):
dt-bindings: one binding file for all simple panels
dt-bindings: one file of all simple DSI panels
Quoted 6 lines
.../display/panel/ampire,am-480272h3tmqw-t01h.yaml | 42 -------------- .../display/panel/ampire,am800480r3tmqwa1h.txt | 7 --- .../display/panel/panasonic,vvx10f034n00.txt | 20 ------- .../bindings/display/panel/panel-simple-dsi.yaml | 67 ++++++++++++++++++++++ .../bindings/display/panel/panel-simple.yaml | 59 +++++++++++++++++++ 5 files changed, 126 insertions(+), 69 deletions(-)
I like this. With the improved structure that the YAML bindings provide this becomes rather neat. You may want to update the subject of the patches to better reflect the style (most seem to use "dt-bindings:
display: " as prefix, for example). But overall, looks good:
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel